双层加筋结构有源隔声物理机制研究

深入分析双层加筋结构有源隔声的物理机制有助于控制系统的优化设计。用模态叠加法和声振耦合理论对双层加筋有源隔声结构建模。在辐射加筋板声功率最小的控制条件下,从模态耦合的角度对有源隔声的物理本质进行了详细阐述。分析结果表明,由于双层加筋板中筋的耦合作用影响,系统的声能量传输规律及有源隔声机理与现有的模态分析结论相比均发生改变。结合筋的耦合影响,对空腔声场的模态抑制与重构机理进行修正和补充,清晰解释了双层加筋结构有源隔声的物理本质。      

双层加筋结构有源隔声物理机制研究

深入分析双层加筋结构有源隔声的物理机制有助于控制系统的优化设计。用模态叠加法和声振耦合理论对双层加筋有源隔声结构建模。在辐射加筋板声功率最小的控制条件下,从模态耦合的角度对有源隔声的物理本质进行了详细阐述。分析结果表明,由于双层加筋板中筋的耦合作用影响,系统的声能量传输规律及有源隔声机理与现有的模态分析结论相比均发生改变。结合筋的耦合影响,对空腔声场的模态抑制与重构机理进行修正和补充,清晰解释了双层加筋结构有源隔声的物理本质。     

极点配置法弹性平板有源隔声系统优化

对混响声场中的弹性平板有源隔声系统进行优化。根据激励频率范围确定受控模态阶次,在模态空间中建立系统降阶方程,基于极点配置方法,采用分布式系统增加受控模态的阻尼,降低低频共振声传输。同时设计模态滤波器,为控制器提供所需的状态信息。为提高控制效能,本文对传感器和作动器布放位置进行优化,尝试不同极点配置方案,并对耦合控制与独立模态控制方法的隔声效果进行比较。仿真结果显示,极点配置法有源隔声可以有效降低共振声传输,优化布放和独立模态控制方式下,控制力明显降低。优化后的有源隔声系统效能有所提升。      

充液管路系统流体声与结构声的复合有源控制

采用基于谐频自适应控制算法的有源消声与消振系统对充液管路系统突出的低频线谱噪声进行有源控制实验研究.建立了泵水循环管路实验系统,在管路中安装有源消声器对流体声进行控制,在管路出口障板上采用8×8通道有源消振系统控制结构声辐射。开展的低频线谱噪声与振动有源控制实验结果表明,在50~200 Hz频带内,通过结合有源噪声与振动控制可在多数频点取得10 dB以上的降噪效果。针对该实验系统,通过分别控制流体声和结构声分析了两者的贡献.实验结果验证了有源消声与消振系统具有较好的降噪性能,各频点处流体声与结构声占比情况不同,需要综合控制流体声与结构声才可以取得显著的降噪效果。      

轻质金属三明治板的隔声性能研究

基于金属三明治板的周期特性,建立了其夹芯层等效弹簧和扭簧组合模型.利用所建立的模型和空间谐波展开法,首先研究了中间为空气腔的双层板的隔声性能,理论结果与实验结果取得较好的一致,验证了模型的合理性;并进一步研究了中间层为瓦楞加筋三明治板的隔声性能.结果表明,声波入射角以及瓦楞加筋板与平板的夹角对其隔声性能影响显著,适当改变瓦楞加筋板与平板的夹角可以有效避开结构的隔声低谷;三明治板对垂直入射声波的隔声效果最好.     

基于平面声源的三层有源隔声结构物理机制研究

次级源为平面声源的三层有源隔声结构,深入理解有源隔声的物理机理有助于挖掘降噪潜力及实现系统优化设计。首先对三层有源隔声结构建模并求解系统的振动响应。然后,对控制前三层结构中声能量的传输规律进行深入分析。最后,在辐射板声功率最小条件下,通过分析控制前后声能量传输特性的变化阐述了隔声的物理机理。结果表明,声能量在三层结构中传输形成四个等效的传输通道,中间板与两腔的作用类似带通滤波器,不同的传输通道具有相似的带通特性。有源隔声机理在于,通过控制抑制了通带内的能量传输,显著提高了三层结构整体的隔声性能,从而有效阻止了声波的向后传播。      

水下充水圆柱声腔内声场自适应有源控制实验研究

本文研究了有限长充水圆柱置于水中，外声场透射形成的腔内声场自适应有源控制实验研究，结果显示，由于圆柱结构与水介质的耦合，有源控制中的声控制方法能够较好的抵消声腔主导模态和强耦合的结构主导模态，因而能够抵消在圆柱腔内较宽频带范围的声场，实验还研究了消声频带，误差传感器布放位置及肖声区域等问题。     

正交加筋板声透射的板梁理论模型研究

为了研究正交加筋板的声透射问题,基于经典薄板和梁振动理论,建立了正交加筋板声透射的板梁理论模型。首先通过分析加强筋的受迫弯曲和扭转运动,求得了平板和加强筋线接触之间的反力和反力矩,然后将其引入到平板振动控制方程中,得到了正交加筋板声振方程,最后采用空间谐波展开法求解该方程得到了传声损失的表达式;在此基础上,首先研究了无限大平板和单向加筋的隔声性能,通过与解析解及两种简化模型的计算结果作对比,验证了所建理论模型的有效性;并进一步研究了加筋形式对正交加筋板隔声性能的影响。结果表明:选择合适的加筋形式可以有效避开结构的隔声波谷。      

有源声学结构降噪的物理机制分析

有源声学结构是近年来提出的降低结构低频声辐射的有效方案,对其降噪中的物理机制进行分析将为系统优化设计、次级源和误差传感器布放及控制目标选取等关键问题提供直接指导。文中在最小辐射声功率条件下,从控制前后初、次级结构的辐射声功率变化以及声场中声强的分布来阐述降噪中的物理机制,研究结果表明:降噪中的能量转换分为能量抑制、能量吸收及能量反吸收三种机制;对于近场声强分布,有源控制效果主要通过声强幅度抑制和声强方向调整两种机制体现,部分区域的声能量在控制前向远场传递,控制后则流向声源。     

双层板腔结构声传输及其有源控制研究

利用子系统模态综合方法,结合阻抗-导纳矩阵法,建立了双层板腔结构向自由空间声传输及其在入射板PZT控制、辐射板PZT控制,和腔中次级声源作动等多种控制策略下,系统物理模型的统一的分析模型,导出了系统模态响应及最优次级源强度的统一的阻抗-导纳矩阵表达式。该模型表达式各部分物理意义清晰、明确,便于进行系统耦合理论、有源控制及其机理的分析和数值研究。然后,在此基础上对双层板腔结构声传输有源控制进行了全面深入的数值计算和分析研究,重点探讨了控制方法策略及系统参数对有源控制效果的影响及其对应的控制机理。结果表明:入射板PZT作动辐射声功率最小控制策略是通过入射板、声腔和辐射板三个子系统的模态抑制或重组达到消声的目的,涉及多种复杂控制机理,对入射板、辐射板和声腔模态均有效,但对入射板模态更有效;在低频段声腔(0,0,0)模态在系统耦合响应中起主导作用,因此利用腔中次级声源作动能获得较理想的控制效果,是一种较好的控制策略;由于声腔模态与结构模态间复杂的耦合关系,使得某些频率处腔中声势能一定程度上的降低并不一定导致系统声传输损失的增加,因此,腔中声势能最小控制策略不一定能够获得理想的声传输控制效果。      

Transmission loss of orthogonally rib-stiffened double-panel structures with cavity absorption

The transmission loss of sound through infinite orthogonally rib-stiffened double-panel structures having cavity-filling fibrous sound absorptive materials is theoretically investigated. The propagation of sound across the fibrous material is characterized using an equivalent fluid model, and the motions of the rib-stiffeners are described by including all possible vibrations, i.e., flexural displacements, bending, and torsional rotations. The effects of fluid-structure coupling are account for by enforcing velocity continuity conditions at fluid-panel interfaces. By taking full advantage of the periodic nature of the double-panel, the space-harmonic approach and virtual work principle are applied to solve the sets of resultant governing equations, which are eventually truncated as a finite system of simultaneous algebraic equations and numerically solved insofar as the solution converges. To validate the proposed model, a comparison between the present model predictions and existing numerical and experimental results for a simplified version of the double-panel structure is carried out, with overall agreement achieved. The model is subsequently employed to explore the influence of the fluid-structure coupling between fluid in the cavity and the two panels on sound transmission across the orthogonally rib-stiffened double-panel structure. Obtained results demonstrate that this fluid-structure coupling affects significantly sound transmission loss (STL) at low frequencies and cannot be ignored when the rib-stiffeners are sparsely distributed. As a highlight of this research, an integrated optimal algorithm toward lightweight, high-stiffness and superior sound insulation capability is proposed, based on which a preliminary optimal design of the double-panel structure is performed.     

高效半解析方法分析周期正交加筋板的振动-声辐射特性

为了对水下无穷大双周期正交加筋板结构模型在简谐面力激励下的振动响应及声辐射特性进行更为合理的理论预测与分析,建立了加筋板结构的数学模型。结合傅里叶变换、泊松迭加公式及空间波数法,将周期加筋板的振动响应及辐射声压表达为关于结构位移谐波分量的函数方程,对加筋板模型提出了高效分析求解方法并进行了谐波分量截断求解。验证了方法的正确性,并分析了结构的振动特性以及加强筋周期间距和扭矩对辐射声压的影响。结果表明,加强筋的扭转作用影响加筋板结构的振动模态频率,对于较高精度要求的工程应用,加强筋的扭转作用不能忽略。通过调节加强筋周期间距及横截面尺寸,可以降低薄板在较低频域区间的远场辐射声压。      

Mechanisms of active control of noise transmission through triple-panel system using single control force on the middle plate

This paper presents an active triple-panel sound insulation structure with an idealized controllable point force acting on the middle plate. A novel analytical approach based on sound energy transmission rule is proposed to achieve the physical mechanism study. The transfer impedance matrix of the incident and middle plate is calculated using numerical approach. And the rule of sound energy transmission through the triple-panel structure is concluded by indirectly analyzing the radiated sound power of the three plates. Finally the physical mechanism of noise insulation is investigated from the point of view of the change in behaviors of energy transmission in controlled and uncontrolled conditions. Results obtained demonstrate that there exist four different energy transmission paths for four panel mode groups. The energy transmission is independent in each path and they are all of band-pass characteristic. The role of the middle plate and two cavities is very similar to the band-pass filter whose pass-band is different for different mode groups. The essence of active noise insulation lies in the fact that the energy transmission in each path is suppressed in its pass-band after control. This greatly improves sound insulation capability of the triple-panel structure and leads to sound propagation being blocked.     

Effectiveness of T-shaped acoustic resonators in low-frequency sound transmission control of a finite double-panel partition

Double-panel partitions are widely used for sound insulation purposes. Their insulation efficiency is, however, deteriorated at low frequencies due to the structural and acoustic resonances. To tackle this problem, this paper proposes the use of long T-shaped acoustic resonators in a double-panel partition embedded along the edges. In order to facilitate the design and assess the performance of the structure, a general vibro-acoustic model, characterizing the interaction between the panels, air cavity, and integrated acoustic resonators, is developed. The effectiveness of the technique as well as the optimal locations of the acoustic resonators is examined at various frequencies where the system exhibits different coupling characteristics. The measured optimal locations are also compared with the predicted ones to verify the developed theory. Finally, the performance of the acoustic resonators in broadband sound transmission control is demonstrated.     

Efficient semi-analytical methods for the vibration response of and acoustic radiation from a periodical orthogonally rib-stiffened plate

In order to theoretically predict and analyze the vibration response and acoustic radiation characteristics of a periodical orthogonally rib-stiffened plate,its vibro-acoustic equations of an underwater infinite model are established.The rib-stiffened plate is stimulated by a harmonic plane pressure.By using the Fourier transforms,Poisson's summation formula and space harmonic method,the structural vibration response and acoustic radiation pressure are expressed as functions of displacement harmonic components.Efficient semi-analytical methods are proposed in this work,and then approximate solutions for finite terms of the harmonic components are obtained by employing the truncation technique.Effects of the vibration response,rib spacing and torsional moment of the ribs on the radiation pressure are examined,and the validity of the present methods is also verified.Theoretical results show that the torsional moment of the ribs affects the modal frequencies of the stiffened plate,which should not be neglected in engineering applications with high precision requirement.With attachment of the ribs to the thin plate,its far field radiation pressure can be reduced in the low frequency range by adjusting rib spacing and cross sectional size of the ribs.     

含损伤黏弹性阻尼加筋层合板声功率和指向性变异*

该文旨在研究损伤位置和程度对自由阻尼加筋层合板声辐射功率和指向性的影响。基于Mindlin和Timoshenko梁理论,建立了自由阻尼层合板-梁组合结构有限元模型。数值求解四边简支边界条件自由阻尼加筋层合板振动响应,继而通过Rayleigh积分计算加筋层合板辐射声功率和指向性。将计算得到的前4阶模态固有频率、声辐射功率与指向性与已有文献进行了对比基本一致,验证了数值模型的正确性。最后,详细讨论了损伤位置和程度对自由阻尼加筋层合板固有频率、振型、声辐射功率和指向性的影响,结果表明：随着结构损伤程度的增大,声辐射功率峰值向低频移动,在更多角度上出现明显的指向性;声辐射功率和指向性对损伤位置比损伤程度更加敏感。     

An indirect hybrid sound transmission loss controller

The control of sound transmission through panels is an important noise control problem in the aerospace, aeronautical, and automotive industries. The trend towards using lightweight composite materials that have lower sound insulation performance is a negative factor regarding low frequency transmission loss. Double-panel partitions with the gap filled with sound absorption materials are often employed to improve the sound insulation performance with reduced added weight penalty. However, in the low frequency range, the strong coupling between the panels through the air cavity and mechanical paths may greatly reduce the sound transmission performance, making it even lower than the performance of a single panel in some frequency ranges. In this work, an experimental investigation of a new kind of hybrid (active/passive) acoustic actuator is presented. The idea consists of replacing the acoustic absorption material by a hybrid actuator aiming at improving the transmission loss at low frequencies without altering the passive attenuation. A prototype of the system is tested in a plane wave acoustic tube setup. Different kinds of SISO feedforward control implementations were used to attenuate the sound power transmitted through the hybrid active–passive panel using an error microphone or a particle velocity sensor placed downstream with respect to the sample panel. Measurement results of the transmission loss with active and hybrid attenuation are presented and discussed.