幂函数型环形聚能器径向振动的等效电路

基于机电类比原理和变厚度薄圆环的平面应力方程,推导了幂函数型环形聚能器径向振动的等效电路、共振频率方程和位移放大系数。讨论了第一、二阶径向共振频率及相应的位移放大系数随圆环半径比的变化关系。结果表明,幂函数型环形聚能器径向振动的等效电路是一种非互易二端口等效网络;一阶和二阶共振频率随圆环内外半径比的增大而增大;一阶径向共振模式下位移放大系数随圆环半径比的增大先降低后升高,二阶径向共振模式下位移放大系数随圆环半径比的增大而降低,但二阶时的位移放大系数整体大于一阶,因此二阶径向共振模式具有更好的径向振动性能。用COMSOL有限元软件对解析理论分析结果进行了验证,仿真模拟结果与解析理论符合良好。根据幂函数型环形聚能器的等效电路模型,进一步设计了一种压电环形换能器,计算了第一、二阶径向共振频率、反共振频率及有效机电耦合系数,通过与COMSOL有限元软件模拟结果对比,符合良好。本文研究结果为幂函数型环形聚能器及压电环形换能器的工程应用提供了简明设计理论,文中研究结论可作为一种径向超声切割刀在超声工程中获得重要应用。      

夹心式径向复合压电超声换能器

对夹心式径向复合压电换能器径向振动特性进行了研究。该换能器由弹性内芯、预应力金属管及柱面压电陶瓷晶堆径向复合而成.利用机电类比法,得到了换能器的径向振动等效电路及频率方程。探讨了换能器第1、2阶径向共振频率及有效机电耦合系数与其几何尺寸的关系。研究表明,换能器第1阶径向共振频率随其内芯内径及预应力管壁厚度增大而降低;第2阶共振频率随内芯内径增大存在极小值,但随预应力管壁厚度增大单调下降。此外,采用第2阶径向共振模式能获得较高的有效机电耦合系数,并且压电陶瓷处于位移节线时,换能器有效机电耦合系数达极大值。对换能器共振频率的测试与有限元仿真表明。理论与实验及仿真结果符合较好。      

阶梯圆环压电超声换能器径向振动性能的理论研究*

提出了一种阶梯圆环径向振动压电超声换能器,根据力电类比原理建立了阶梯圆环及阶梯圆环换能器的径向振动等效电路,推导了阶梯圆环的径向共振频率方程和位移放大系数,在此基础上进一步推导了换能器的径向共振和反共振频率方程。通过理论推导和有限元仿真模拟分析了阶梯圆环压电超声换能器的径向振动性能。结果表明,增大阶梯圆环中内外环的径向厚度之比K1或减小轴向厚度之比K2,阶梯圆环的一阶径向共振频率减小,二阶径向共振频率增大;在二阶径向共振模式下,K1、K2值在一定范围内阶梯圆环可实现由内向外的径向位移振幅放大;随着压电陶瓷圆环的内半径增大,阶梯圆环压电超声换能器的一阶、二阶径向共振和反共振频率减小,二阶径向共振下的有效机电转换系数趋于零;增大阶梯圆环内环的外半径,换能器的一阶径向共振和反共振频率减小,二阶径向共振和反共振频率先增大后减小,理论推导与仿真模拟结果符合良好。本文研究结果为阶梯圆环压电超声换能器的工程应用提供理论参考。     

盘形聚能器设计理论

理论上研究了盘形聚能器的轴对称纯径向振动和纯扭转振动。所用盘形聚能器的厚度,沿半径按阶梯形,锥形和指数形变化。我们获得了解析解,然后给出了共振频率、速度分布、振幅比和节点位置公式。最后用两例实验来验证我们的理论,实验结果与理论符合地较好。     

径向复合圆柱压电超声换能器

提出一种三元径向复合圆柱压电超声换能器,并对其径向振动特性进行了研究。基于弹性力学理论及机电类比原理,导出了柱坐标系中分割处理径向极化压电陶瓷管准厚度模振动及薄壁短圆管径向振动的机电等效电路;利用径向力和振速连续的边界条件,得出了径向复合圆柱压电换能器系统的径向振动机电等效电路及其共振频率方程。探讨了换能器径向共振频率及有效机电耦合系数随其几何尺寸的变化关系。研究表明,换能器的径向共振频率及有效机电耦合系数随其内芯半径和预应力管壁厚度增大而降低。研制了一些径向复合圆柱压电换能器,并对其径向共振频率进行了测试。结果表明,理论与实验结果基本一致。      

基于2-2型压电复合材料的新型宽频带径向振动超声换能器

本文提出了一种基于2-2型压电复合材料的新型宽频带径向振动超声换能器,它主要由内金属圆环和外压电陶瓷复合材料圆环组成.首先利用Newnham串并联理论和均匀场理论推导了2-2型压电复合材料的等效参数;其次利用解析法得到了金属圆环和径向极化压电复合陶瓷圆环径向振动的机电等效电路;最后得到了换能器的六端机电等效电路,从而得到了换能器的频率方程.接着分析了换能器共振频率和反共振频率以及有效机电耦合系数与几何尺寸、两相体积占比的关系,采用仿真软件对新型换能器的径向振动进行了数值模拟.结果表明,利用解析法得到的共振频率和反共振频率与数值模拟结果吻合较好.此外,对换能器在水下的辐射声场进行了仿真研究,结果表明新型复合材料径向换能器相比传统纯陶瓷径向换能器,发射电压响应幅值更大,工作带宽提高接近一倍,声匹配更佳.     

径向极化压电陶瓷长圆管复合超声换能器的径向振动

提出了一种圆管式径向复合压电陶瓷换能器,并对其径向振动特性进行了分析。该换能器由径向极化的压电陶瓷圆管以及金属外圆管组成。利用解析法得出了金属圆管以及具有任意壁厚的径向极化压电陶瓷圆管径向振动的机电等效电路。基于金属圆管与压电圆管的机械边界条件,得出了换能器的六端机电等效电路。在此基础上得出了换能器共振及反共振频率方程的解析表达式,给出了换能器的共振及反共振频率与其几何尺寸之间的依赖关系。利用数值方法对换能器的径向振动特性进行了模拟及仿真,并与解析结果进行了比较。最后,设计并加工了一些径向复合管式压电陶瓷换能器,利用精密阻抗分析仪对其共振及反共振频率进行了实验测试。研究结果表明,利用解析理论得出的换能器共振及反共振频率与数值模拟结果以及实验测试结果符合很好。      

基于传输矩阵法的任意变厚度环型压电超声换能器

变厚度环型径向振动压电超声换能器可以实现阻抗变换、能量集中,具有辐射面积大、全指向性等优点,在功率超声、水声等领域被广泛应用.由于求解复杂变厚度金属圆环径向振动的波动方程比较困难,本文使用传输矩阵法将变厚度金属圆环的径向振动转化为N个等厚度金属圆环径向振动的叠加,得到了任意变厚度金属薄圆环径向振动的等效电路图、共振频率方程和位移放大系数表达式,分析了锥型、幂函数型、指数型、悬链线型金属圆环的位移放大系数与几何尺寸的关系.在此基础上,推导了由任意变厚度金属圆环和等厚度压电圆环复合而成的压电超声换能器径向振动的等效电路和共振频率方程.为了验证理论结果的正确性,使用有限元软件进行仿真,所得一阶、二阶的共振频率和位移放大系数的数值解与理论解符合较好.本研究给出了任意变厚度金属圆环径向振动的普适解,为设计和优化径向压电超声换能器提供了理论指导.     

径向复合压电陶瓷超声换能器的径向振动特性研究

对径向复合压电陶瓷超声换能器的径向振动特性进行了分析。该换能器由一个厚度极化的压电陶瓷实心圆盘和一个金属圆环在半径方向复合而成。论文首先研究了压电陶瓷圆盘及金属圆环的径向振动,推出了其径向振动的机电等效电路。在此基础上,利用换能器的径向边界条件,得出了径向复合压电陶瓷换能器的机电等效电路及其共振频率方程。探讨了换能器的共振频率和有效机电耦合系数与其几何尺寸之间的依赖关系。设计并实际制作了一些径向复合超声换能器,对其径向共振及反共振频率进行了测试,并利用有限元法进行了数值模拟。研究表明,利用文中理论得出的换能器的共振频率与实测值及数值模拟结果基本符合。     

同向振动L-L振动方向变换器的等效电路

基于表观弹性法和机电类比原理,推导了L-L振动方向变换器正交复合振动系统的机电等效电路及谐振频率方程。分别利用等效电路法、波动方程法,通过有限元法计算并结合实验测试分析了变换器同向振动的共振频率与其纵向及横向尺寸的变化规律。研究表明,变换器做同向振动时的共振频率随其纵向尺寸的增加而减小,随其横向尺寸的增加而增大;比较三种方法计算结果可知,本文给出的等效电路模型计算结果和有限元仿真结果均与实验测试结果相吻合,为该类超声振动系统的设计提供较为精确的设计理论。     

Radial vibration of a slit-type annular ultrasonic concentrator

The radial vibration characteristic of an annular ultrasonic concentrator with multislits is studied.Based on the electro-mechanical analogy and by introducing an area ratio coefficient,the radial vibrational equivalent circuit and the frequency equation of the concentrator are derived.The radial displacement amplitude magnification factor of it is obtained.By numerical calculating,the relationship between the radial displacement amplitude magnification factor,the resonance frequency of the concentrator at the first and second resonance and its radius ratio are investigated.Also,the relationship between the radial displacement amplitude magnification factor,the resonance frequency of the concentrator and the length,the angle and the number of the silts are analyzed.It is illustrated that a maximum of displacement amplitude magnification factor of the concentrator appears with the increase of the radius ratio,and the amplitude magnification factor increase as the length,the angle and the number of the silts increase,while the radial resonance frequency of the concentrator decreases as the length,the angle and the number of the silts increase.The theoretical resonance frequencies are in good agreement with that of the FEM simulations and measurement.     

Study on the step-type circular ring ultrasonic concentrator in radial vibration

In this paper, the plane radial vibration of an isotropic metal thin circular rings is studied and its equivalent circuit model is obtained. Based on the equivalent circuit model, the step-type circular ring concentrator consisting of two metal thin circular rings in radial vibration is analyzed. Its compound equivalent circuit is derived and the resonance frequency equation is obtained. The relationship between the resonance frequency, the radial displacement amplitude magnification and the geometrical dimensions is analyzed. The resonance frequency of the step-type radial concentrator is calculated based on the resonance frequency equation. For comparison, the resonance frequency of the step-type radial concentrator is also obtained by using numerical method. It is illustrated that the resonance frequencies from these two methods are in a good agreement with each other.     

Study on the radial vibration and acoustic field of an isotropic circular ring radiator

Based on the exact analytical theory, the radial vibration of an isotropic circular ring is studied and its electro-mechanical equivalent circuit is obtained. By means of the equivalent circuit model, the resonance frequency equation is derived; the relationship between the radial resonance frequency, the radial displacement amplitude magnification and the geometrical dimensions, the material property is analyzed. For comparison, numerical method is used to simulate the radial vibration of isotropic circular rings. The resonance frequency and the radial vibrational displacement distribution are obtained, and the radial radiation acoustic field of the circular ring in radial vibration is simulated. It is illustrated that the radial resonance frequencies from the analytical method and the numerical method are in good agreement when the height is much less than the radius. When the height becomes large relative to the radius, the frequency deviation from the two methods becomes large. The reason is that the exact analytical theory is limited to thin circular ring whose height must be much less than its radius.     

Radial vibration and ultrasonic field of a long tubular ultrasonic radiator

The radial vibration of a metal long circular tube is studied analytically and its electro-mechanical equivalent circuit is obtained. Based on the equivalent circuit, the radial resonance frequency equation is derived. The theoretical relationship between the radial resonance frequency and the geometrical dimensions is studied. Finite element method is used to simulate the radial vibration and the radiated ultrasonic field and the results are compared with those from the analytical method. It is concluded that the radial resonance frequency for a solid metal rod is larger than that for a metal tube with the same outer radius. The radial resonance frequencies from the analytical method are in good agreement with those from the numerical method. Based on the acoustic field analysis, it is concluded that the long metal tube with small wall thickness is superior to that with large wall thickness in producing radial vibration and ultrasonic radiation. Therefore, it is expected to be used as an effective radial ultrasonic radiator in ultrasonic sewage treatment, ultrasonic antiscale and descaling and other ultrasonic liquid handling applications.     

粗细端等长阶梯形变幅杆的有限元分析

本文利用有限元分析软件ANSYS研究了一组粗细端截面积比不同的阶梯形变幅杆，得出了每个变幅杆的第一阶和第三阶谐振频率、粗细端分界面的相对位移和振幅放大系数。结果表明：ANSYS仿真值与实测值的平均偏差仅为0．3％，远小于常用式解析值与实测值的偏差；变幅杆粗细端分界面的运动类似受牵引的薄膜运动；而振幅放大系数与面积比成正比的结论可扩展到粗细端截面积比为100的情况。