New efficient laser dye for pulsed and CW operation in the UV

A new laser dye for pulsed and cw operation has been synthesized which can be tuned from 362 nm up to 412 nm. For pulsed excitation with a XeCl excimer laser an energy conversion of 18.5% has been measured at the tuning maximum of the dye; this is the highest efficiency for any known dye in the UV. For cw operation a low laser threshold and a goof efficiency have been observed. The range of tuned cw dye lasers is extended by 30 nm to shorter wavelengths. The dye shows high photochemical stability even at high pump laser power.     

Production of intensities of ∼ 1019 W/cm2 by a table-top KrF laser

We report on the generation of intensities of 10¹⁹ W/cm^–2 by focusing the output beam of a table-top hybrid dye-excimer laser system operating at 248 nm. The laser system uses a pulsed dye laser and a single, commercially available excimer gain module. Considerations and optical arrangements for the optimization of the phase-front and the beam homogeneity of ultraviolet excimer amplifiers are presented.Prof. F.P. Schäfer on the occasion of his 65th birthday.     

Interaction of laser radiation with TNT with respect to the laser neutralisation of AP mines

According to UN estimations there are between 80 and 115 million activated landmines worldwide. These mines, or other unexploded ordnance (UXO), can be triggered accidentally and kill or injure more than 2000 civilians per month. The most common explosive in these mines is trinitrotoluene (TNT). In this paper, the potential of some of the most promising lasers for mine neutralisation is investigated, namely an ArF laser, a KrF excimer laser and a Nd:YAG solid-state laser. We have studied the interaction between laser beams emitting at λ=193 nm, 248 nm and 1060 nm and a bare solid sample of TNT of approximately 15 mg. Using pulsed excimer radiation at λ=193 nm, with an energy density up to 1 J/mm², ablation of the TNT without any deflagration has been achieved. At λ=248 nm, using the KrF excimer laser with a pulse duration of 30 ns and a repetition rate of 5 Hz, the TNT sample started melting and burning after an irradiation of 10 s. Preliminary results with the Nd:YAG solid-state laser operating in cw emission have shown that the irradiated sample exhibits the desired burning behaviour even after the exposure is stopped. Received: 14 December 2000 / Accepted: 18 December 2000 / Published online: 20 June 2001     

Simple generation of high-power,picosecond, tunable excimer laser pulses

A single excimer laser (a modified commercial oscillation-amplifier combination) is used to pump a dye laser generating a single ps pulse at twice the excimer wavelength and to amplify the frequency-doubled pulse to high peak powers. With XeCl at 308 nm an output pulse energy of 10 mJ with <5 ps pulse width was achieved with <5% ASE energy.     

First observation of a resonance ionization signal on242mAm fission isomers

The feasibility of a hyperfine spectroscopy on^242mAm fission isomers has been demonstrated at the low target production rate of 10/s. The experimental method employed is based on resonance ionization spectroscopy in a buffer gas cell with detection of the ionization process by means of the fission decay of the isomers. The resonance ionization has been performed in two steps, utilizing an excimer dye laser combination with a repetition rate of 300 Hz. The first resonant step proceeds through theJ=7/2 term at 21440.35 cm⁻¹, which has been excited with the tuncable dye laser beam of a wavelength of 466.28 nm, the second non-resonant step is achieved with the 351 nm radiation of the excimer laser itself, running with XeF. The frequency scan of the tuneable dye laser exhibits a broad resonance ionization signal, the width of which is most likely explained by the magnetic hyperfine interaction.     

Deposition and characterization of ITO films produced by laser ablation at 355 nm

Indium tin oxide (ITO) films have been deposited by pulsed laser deposition (PLD) at 355 nm. Even though the absorption of laser light at the wavelength 355 nm is much smaller than that of the standard excimer lasers for PLD at 248 nm and 193 nm, high-quality films can be produced. At high fluence and at high substrate temperatures, the specific resistivity of the films, 2–3×10^-4 Ω cm, is comparable to values obtained with excimer lasers, whereas the resistivities obtained at room temperature are somewhat higher than those of films produced by excimer lasers. The transmission coefficient of visible light, about 0.9, is also comparable to values for films deposited by excimer lasers. The crystalline structure of films produced at 355 nm is similar to that of samples produced by these lasers. Received: 16 January 2001 / Accepted: 24 July 2001 / Published online: 17 October 2001     

Pulsed laser action of Pr:GdLiF4 at room temperature

We realized, to our knowledge for the first time, laser emission in Pr:GdLiF₄ at seven wavelengths: 522 nm, 545 nm, 604.5 nm, 607 nm, 639 nm, 697 nm, and 720 nm. The crystal was pumped with an excimer laser pumped dye laser at 468 nm. All laser experiments were carried out at room temperature. We also achieved pulsed room temperature laser oscillation of Pr:KYF₄ at 642.5 nm pumped at 465 nm wavelength.     

Property improvement of pulsed laser deposited boron carbide films by pulse shortening

Growth characteristics and surface morphology of boron carbide films fabricated by ablating a B₄C target in high vacuum with a traditional KrF excimer laser and a high brightness hybrid dye/excimer laser system emitting at the same wavelength while delivering 700 fs pulses are compared. The ultrashort pulse processing is highly effective. Energy densities between 0.25 and 2 J cm⁻² result in apparent growth rates ranging from 0.017 to 0.085 nm/pulse. Ablation with nanosecond pulses of one order of magnitude higher energy densities yields smaller growth rates, the figures increase from 0.002 to 0.016 nm/pulse within the 2-14.3 J cm⁻² fluence window. 2D thickness maps derived from variable angle spectroscopic ellipsometry reveal that, when ablating with sub-ps pulses, the spot size rather than the energy density determines both the deposition rate and the angular distribution of film material. Pulse shortening leads to significant improvement in surface morphology, as well. While droplets with number densities ranging from 1 × 10⁴ to 7 × 10⁴ mm⁻² deteriorate the surface of the films deposited by the KrF excimer laser, sub-ps pulses produce practically droplet-free films. The absence of droplets has also a beneficial effect on the stoichiometry and homogeneity of the films fabricated by ultrashort pulses.     

Radiation detected resonance ionization spectroscopy on208Tl and242fAm

An ultra-sensitive laser spectroscopic method has been developed for the hyperfine spectroscopy of short-lived isotopes far off stability produced by heavy ion induced nuclear reactions at very weak intensity (> 1/s). It is based on resonance ionization spectroscopy in a buffer gas cell with radiation detection of the ionization process (RADRIS). As a first on-line application of RADRIS optical spectroscopy at^242fAm fission isomers is in progress at the low target production rate of 10/s. The resonance ionization has been performed in two steps utilizing an excimer dye laser combination with a repetition rate of 300 Hz. The first resonant step proceeds through terms which correspond to wavelengths of 466.28, 468.17 or 426.56 nm; the second non-resonant step is achieved with the 351 nm radiation of the excimer laser itself, running with XeF. The frequency scans of the tuneable dye laser at 466.28 and 468.17 nm exhibit broad resonance ionization signals, the latter with a large isotope shift between^242fAm and²⁴³Am which is in accordance with the large quadrupole moment of the^242fAm fission isomer.Work supported by the Bundesministerium für Forschung und Technologie under contract 06 MZ 188 I.     

Pulse properties of a synchronously mode-locked,cavity dumped,picosecond dye laser system

A synchronously mode-locked, cavity-dumped picosecond dye laser is described. The structure and intensity of the picosecond pulses measured under different conditions are reported. It was found that the structure of the pulses from the synchronously pumped dye laser depends critically on the length of the Ar⁺ laser pulses. At the shortest Ar⁺ laser pulses of about 70 ps the dye pulses are as short as 1.1 ps. With Ar⁺ laser pulses of 200 ps the dye laser pulses contains a broad satellite pulse which contains a large fraction of the total intensity. When a cavity dumper is added to the system one gets dye laser pulses 15–20 ps long with a substructure, which indicates incomplete mode-locking. Well mode-locked 1.5–2.0 ps pulses were obtained in the red part of the dye laser action spectrum, i.e. 620–650 nm for R6G, 595–608 nm for R 110 and 657–662 nm for RB, respectively. Addition of mode-locking dyes also improved the pulse quality at some wavelengths.     

Excited singlet-state absorption in laser dyes at the XeCl wavelength

The transmission properties of the laser dyes BBQ, PBD, BPBD, -NPO,p-Quarterphenyl and PPO have been measured using a XeCl (308 nm) excimer laser. A model for the dye saturation which incorporates excited-state absorption was used to estimate the lifetime and the absorption cross section of the first excited singlet-state for each dye.     

Tunable distributed-feedback laser based on dye doped microporous quartz glass

The first distributed feedback (DFB) dye laser on the basis of microporous quartz glass (MQG) is reported. MQG consists of a specially processed quartz sample doped with a dye. As a pumping source a second harmonic YAG: Nd³⁺ laser with 12.5 pps repetition rate was used. Stable generation of the narrow line tuned within a spectral range of 562–584 nm and 633–663 nm with a linewidth of 0.04 nm was obtained. A high photochemical stability of the dye in the quartz matrix and reliability of MQG as an active medium for the tunable DFB laser were experimentally demonstrated.     

300 Femtosecond pulses at 497 nanometer generated by an excimer laser pumped cascade of distributed feedback dye lasers

The setup is a cascade of 3 lasers: A competing cavity dye laser pumped by a XeCl excimer laser, followed by two distributed feedback dye lasers. The typical durations of the pulses from the lasers are 100 ps, 5 ps, and 300 fs, respectively. The output pulses at 497 nm are amplified up to 500 MW. The shortest pulse duration obtained was 198 fs.     

Solid-state laser system for laser cooling of sodium

We demonstrate a frequency-stabilized, all-solid laser source at 589 nm with up to 800 mW output power. The laser relies on sum-frequency generation from two laser sources at 1064 nm and 1319 nm through a PPKTP crystal in a doubly resonant cavity. We obtain conversion efficiencies as high as 2 W/W² after careful optimization of the cavity parameters. The output wavelength is tunable over 60 GHz, which is sufficient to lock on the sodium D₂ line. The robustness, beam quality, spectral narrowness and tunability of our source make it an alternative to dye lasers for atomic physics experiments with sodium atoms.     

Photophysical properties and laser performance of rubrene

The potential of rubrene as a laser dye was investigated in deaerated solutions with a XeCl excimer laser as pump source. Laser tuning range, quantum efficiency and photostability as well as excited singlet state absorption (ESA) spectra were measured. The (S₁-S₂) absorption band strongly overlaps with the fluorescence spectrum and thus ESA constitutes an important loss factor in the lasing process while triplet absorption can be neglected in the wavelength region of interest. Laser performance of rubrene is superior compared to other polycyclic aromatic hydrocarbons which can be considered as model compounds of the lasing process in organic dyes.     

Silicon nanowires synthesized by vapor–liquid–solid growth on excimer laser annealed thin gold film

The fabrication of Si nanowires has been demonstrated using excimer laser annealed thin gold film as the catalyst and vapor–liquid–solid (VLS) growth. Au nanoparticles with mean diameters of 12, 13 and 15 nm were formed by excimer laser annealing (ELA) of Au film with thickness of 2.5, 5 and 10 nm, respectively. The results show that the silicon nanowires (SiNWs) with desired diameter can be obtained by controlling the Au film thickness and laser power density.     

Enhanced laser performances based on energy transfer in multi-dyes co-doped solid media

Various coumarin dyes are co-doped with perylene red (P-red) and pyrromethene 567 (PM567) into vinyltriethoxysilane-derived solid media, respectively. Energy transfer among laser dyes has been observed, and the effect of coumarin dye concentration on the laser properties has been investigated. With the presence of coumarin dye and pyrromethene 567, enhanced laser performances based on energy transfer of perylene red have been exhibited. The laser efficiency can be improved by two-fold and broad tunable range as wide as 80 nm can be achieved. At the pump intensity of 1.0 J/cm², the laser output of co-doping perylene red decreases less than 30% after 30,000 pulses.     

Color center laser pumped with a DCM dye laser

A CW, DCM dye laser has been used to pump a RbCl:Li crystal in a color center laser. The DCM dye laser was pumped by the 488 nm and 514.5 nm lines of an argon ion laser. When used in a broad band configuration the dye laser had a power output in the TEM₀₀ mode in excess of 600 mW at a wavelength of 655 nm. An output power in excess of 10 mW at 2.73 μm was possible from the RbCl:Li crystal in a Burleigh FCL for an input power of 600 mW at 655 nm. This method of pumping for the RbCl:Li alleviates the need for both argon ion and krypton ion laser pumps for the Burleigh FCL. All three crystals can be pumped to the specification power levels with a single argon ion laser.     

Femtosecond uv excimer laser ablation

Experiments on the ablation of polymethylmethacrylate (PMMA) with 300 fs uv excimer laser pulses at 248 nm are reported for the first time. With these ultrashort pulses, ablation can be done at fluences up to five times lower than the threshold fluence for 16 ns ablation of PMMA, and the surface morphology is improved, also for several other materials. A model for ablation is proposed, assuming a non-constant absorption coefficient _eff depending on the degree of incubation of the irradiated material and the intensity of the incoming excimer laser pulse. The agreement between our model and our experimental observations is excellent for 16 ns excimer laser pulses, also predicting perfectly the shape of a pulse transmitted through a thin PMMA sample under high fluence irradiation. Qualitative agreement for 300 fs excimer laser pulses is obtained so far.     

Generation of high peak power excimer laser radiation by pulse shortening

Techniques for shortening the pulses of a commercial oscillator-amplifier excimer laser have been investigated. By a combination of a H₂-Raman cell and a saturable absorber dye jet the oscillator pulses are shortened from about 25 ns to typically 1.5 ns. Upon amplification pulses around 3.5 ns with peak powers of more than 100 MW for KrF (248 nm) and 25 MW for XeCl (308 nm) are obtained.