纳米管结构聚苯胺的电阻率和磁化率

研究了用自组装法制备的质子酸掺杂的纳米管结构聚苯胺的电阻率(ρ)和磁化率随温度变化的依赖关系，讨论了质子酸掺杂浓度、不同对阴离子以及苯胺单体与质子酸聚合时反应浓度对纳米管结构聚苯胺电学性质的影响.实验结果表明，lnρ和T-1/2呈线性关系，不同对阴离子对聚苯胺的电阻率影响很大，随着质子酸掺杂浓度以及苯胺单体与质子酸聚合时反应浓度的增大，聚苯胺的电阻率明显减小；而且，其磁化率可以表示为与温度无关的泡利顺磁性和符合居里定律的顺磁性之和.     

一步和两步法制备阳极氧化铝模板(英文)

手二步阳极氧化法制备了大面积上有规则排列纳米洞的阳极氧化铝模板。与一步阳极氧化法的结果进行了比较,SEM测量表明,一步阳极氧化得到的AAO模板正面(对着负电极的一面)和反面,有很大不同,正面纳米洞的分布更不规则,而二步法得到的模板正反面都有排列规则的纳米洞。这一结果也表明阳极氧化过程是一种自组织有序的过程,氧化时间越长,纳米洞的分布越规则越均匀     

苯酚苯胺共聚物在304不锈钢电极表面的电化学合成及成膜微观结构分析

苯酚和苯胺在304不锈钢阳极表面实现了电化学共聚,反应在中性水溶液中进行,电解质为硫酸钠. 比较不同苯酚苯胺浓度下共聚成膜耐点蚀能力,当苯酚为0.09 mol/L和苯胺为0.01 mol/L时最佳.红外光谱分析证实苯胺结构出现在苯酚苯胺的共聚物中,且共聚物膜比聚苯酚膜含有更多支链. 利用苯酚苯胺共聚物膜在四氢呋喃中的部分溶解性,使用扫描电子显微镜分析四氢呋喃清洗前后的成膜,观察到网状聚苯胺结构. 将共聚物膜与聚苯酚膜微观结构进行推测和比较,解释在电聚合反应中适量加入苯胺能提升成膜防腐能力原因.     

导电聚苯胺的合成及其性能研究

化学氧化法合成了导电性聚苯胺 ,系统地研究了氧化剂种类、浓度、反应温度、反应时间、掺杂酸的种类和浓度等不同因素对聚合反应的影响 ,获得了苯胺聚合反应的最佳条件。     

对硝基苯胺与牛血清白蛋白的相互作用

采用荧光光谱法研究了不同酸度下对硝基苯胺与牛血清白蛋白(BSA)间的相互作用.实验结果表明,对硝基苯胺能与BSA形成复合物而导致BSA内源性荧光猝灭,猝灭机理为静态猝灭过程.经计算得到了不同酸度和不同温度下对硝基苯胺与BSA反应的结合常数、结合位点数.结合过程的热力学参数变化表明,该相互作用是一个熵增加、Gibbs自由能降低的自发作用过程,其作用力类型主要为静电作用力.     

荧光光谱法研究2-硝基苯胺与牛血清白蛋白的相互作用

采用荧光光谱法研究了不同酸度下,2-硝基苯胺与牛血清白蛋白(BSA)间的相互作用。实验结果表明,2-硝基苯胺对BSA的猝灭机制属于静态猝灭过程。经研究得到了不同酸度和不同温度下2-硝基苯胺与BSA反应的结合常数、结合位点数。根据热力学常数确定了二者间的作用力类型为氢键和疏水作用力。同步荧光结果表明,2-二硝基苯胺的存在改变了牛血清白蛋白的分子构象。     

聚苯胺与还原石墨烯复合材料的微波吸收性能

采用化学氧化法制备聚苯胺与还原石墨烯复合材料。复合材料的结构、晶型和电磁参数分别通过X射线衍射仪及HP8722ES型矢量网络分析仪进行表征、测试与分析。结果表明,同聚苯胺相比,聚苯胺与还原石墨烯复合材料的介电损耗明显增加。而且在复合材料中,石墨烯的含量越大,材料的微波吸收性能越好,在频率波段（9.5~13.4GHz）反射损耗均小于-10 dB,并在频率为11.2 GHz时达到最大反射损耗-29.69 dB。聚苯胺与还原石墨烯的复合使得材料的载流子迁移率变大,吸波特性得到改善。     

萘磺酸掺杂对纳米管结构聚苯胺低温电阻率的影响

通过研究用自组装法制备的萘磺酸掺杂的纳米管结构聚苯胺(苯胺与萘磺酸的摩尔比分别为1∶025,1∶05,1∶1,1∶2,1∶3)的电阻率温度依赖关系(测量温区为80—300K),仔细分析聚苯胺的结构形貌特征,提出了变程跳跃隧道穿透混合模型:认为在萘磺酸掺杂的纳米管结构聚苯胺样品中,跳跃和隧穿两种机制同时起作用,载流子沿纳米管传导是变程跳跃过程起主要作用,而载流子在纳米管之间的传导是隧穿过程起主要作用.实验结果表明,不同浓度的萘磺酸掺杂对样品的低温电阻率的影响很大,随着掺杂浓度增加,载流子传导所需克服的能垒C0迅速减小,当掺杂接近饱和时,C0不再减小.实验中还研究了不同形貌对电阻率的影响,结果表明样品中纳米管所占比例的增大有利于载流子传导 关键词： 聚苯胺 纳米管 低温电阻率     

光助Fenton氧化反应降解染料罗丹明B

研究了不同光源条件下光助Fenton反应催化氧化降解有机染料罗丹明B脱色情况及相关机理。内容包括 :不同光源、初始反应溶液酸度、反应时间、Fenton试剂浓度、初始染料溶液浓度等因素对光助Fen ton反应的影响 ,确定了方法的优化条件 ,并讨论了光助Fenton反应的反应机理。研究表明 :在 pH =3 5的条件下 ,4 5 0W高压汞灯照射以及较强太阳光照射的条件均可以明显加快Fenton法催化氧化降解罗丹明B溶液的过程 ,色度脱除率可达到 99%以上 ,COD也得到有效去除     

纳米TiO_2∶Zn薄膜电极紫外光电特性研究

采用sol-gel法制备了Zn2 掺杂的锐钛矿相纳米TiO2薄膜电极.通过光电流作用谱和电流-电位(I-U)曲线研究了掺杂不同浓度Zn2 的TiO2薄膜电极的光电特性.由光电流作用谱可知,Zn2 的掺杂可显著影响薄膜电极的光电流大小,且掺杂的最佳浓度与薄膜晶粒尺度有关.在320nm单色光照射下,掺杂浓度(摩尔浓度)为0.1%的薄膜电极光电流最大,与未掺杂的本征薄膜电极相比增幅达40%.I-U曲线表明,光照下,随电极电位由正到负逐渐降低,不同掺杂浓度的TiO2薄膜电极中均出现了阳极电流向阴极电流转换的现象,且Zn2 掺杂浓度可影响电极阳极电流的初始电位.另外,无光照的暗态下,各薄膜在负电位区域观察到了相似的随电位降低而迅速增大的阴极暗电流.     

A novel nitroxide radical polymer-containing conductive polyaniline as molecular skeleton: its synthesis and electrochemical properties as organic cathode

A novel nitroxide radical-containing aniline, 4-(6-(2-amino-phenol-9H-yl)hexanoyloxy)-2,2,6,6-tetramethylpiperidin-1-yloxy (AnT), was synthesized, and the copolymers of AnT and aniline (P (An-co-AnT)) were then prepared by chemical oxidative polymerization. The introduction of polyaniline (PAn) skeleton in copolymers improved the charge migration along polymer backbone, and the increased ratio of An/AnT monomer makes PAn’s anodic peak in copolymers shift to negative potential and the redox peaks for the nitroxide radical shift to the positive potential. Also, P (An-co-AnT) exhibited a gradually increased charged specific capacity from 120.1 to 141.0 mAh g^?1 with increasing the feeding ratio of AnT/An, while the discharge specific capacity presented an opposite result. Specially, P (An-co-AnT) exhibited an obvious charge voltage platform and an even improved cycling stability than that of PAn in the high feeding ratio of AnT/An, and after 20 cycles, the discharge capacity of P (An-co-AnT) (1:1 ([An]/[AnT])) still maintained 82.7 % of the capacity obtained at the initial cycle.     

铋酸钠催化大气压介质阻挡放电降解苯胺

在柱-板式介质阻挡放电体系中投加铋酸钠催化剂,研究了该体系的放电光谱特性及对苯胺模拟废水的协同处理效果,考察了pH 值、苯胺初始质量浓度及催化剂投加量等因素对降解率的影响,探讨了铋酸钠协同介质阻挡放电(DBD)催化降解苯胺的机理。实验结果表明,柱-板式电极结构放电过程中辐射出了紫外光和可见光,300~450 nm之间出现高强度N2第二正带谱线。初始浓度100 mg/L苯胺废水被处理10 min后,投加0.2 g/L催化剂时溶液的TOC去除率最高,比单独DBD低温等离子体体系提高14.11%。在碱性条件下,苯胺和TOC的去除率均好于酸性和中性条件。XRD检测结果显示铋酸钠在反应前后峰值位置未发生明显改变。     

Decomposition of nitrotoluenes in wastewater by sonoelectrochemical and sonoelectro-Fenton oxidation

Oxidative degradation of dinitrotoluene (DNT) and 2,4,6-trinitrotoluene (TNT) in wastewater was conducted using electrochemical and electro-Fenton processes respectively, combined with ultrasonic irradiation, wherein a synergistic effect is observed. Experiments were carried out to elucidate the influence of various operating variables on the sonoelectrolytic behavior, such as electrode potential, sonoelectrolytic temperature, acidity of wastewater, oxygen dosage, and dosage of ferrous ions. It deserves to note that the nitrotoluene contaminants could be completely decomposed by sonoelectro-Fenton method, wherein hydrogen peroxide was in situ generated from cathodic reduction of oxygen, supplied partially by anodic oxidation of water. During the sonoelectrolytic process, in spite of existence of degassing phenomenon, the high yield of hydrogen peroxide was produced due to the significantly enhanced mass transfer rate of oxygen toward the cathode, caused by ultrasonic irradiation. Because higher removal efficiency of DNTs and TNT obtained at ambient conditions, it is believed that the sonoelectrolytic method is potentially applied to dispose wastewater from toluene nitration processes.     

Effect of crystallographic orientation on the anodic formation of nanoscale pores/tubes in TiO2 films

Self-organized nanopores and nanotubes have been produced in thin films of titanium (Ti) prepared using filtered cathodic vacuum arc (FCVA), DC- and RF-sputter deposition systems. The anodization process was performed using a neutral electrolyte containing fluoride ions with an applied potential between 2 and 20 V (for clarity the results are only presented for 5 V). Scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) techniques were used to characterise the films. It was found that the crystallographic orientation of the Ti films played a significant role in determining whether pores or tubes were formed during the anodic etching process.     

电化学染料增感对聚苯胺/硅异质结电池的影响

采用电化学氧化聚合染料增感方法，利用有机染料直接耐晒翠兰对太阳电池顶区材料聚苯胺进行了有机染料增感研究，制备出了Al栅/DS-PAn/n-Si/Al结构的染料增感聚苯胺/硅异质结太阳电池.研究表明，染料增感可使聚苯胺在光照射下光生载流子明显增强，较大幅度地改善聚苯胺的可见光谱响应；J-V特性表明，电池二极管的曲线因子约为6.3，p-n结的潜在势垒高度为0.89 eV；与未增感的PAn/n-Si异质结太阳电池相比，染料增感的DS-PAn/n-Si异质结太阳电池的短路电流和转换效率得到了较大提高，在37.2 W/m2的光照射下，经染料增感的电池短路电流较增感前提高了约6倍，填充因子可达57%，转换效率达1.42%.     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术,分别沉积Ti和Ti/Al膜,经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序,分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27 关键词： 2薄膜')" href="#">多孔TiO₂薄膜 阳极氧化 紫外光吸收     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

纳米结构锌及锌氧化物薄膜对甲基橙的降解作用研

采用磁控溅射方法制备了纳米金属锌薄膜,结合后续的空气退火处理制备了纳米锌氧化物薄膜. 金属锌薄膜对甲基橙的还原降解以及锌氧化物薄膜对甲基橙的光催化降解过程都可以用一级反应动力学方程来描述. 甲基橙溶液在金属锌膜的还原降解下具有最快的褪色速率,但矿化不完全：在紫外光波段出现的额外吸收峰表明生成了芳香族中间产物. 完全氧化的氧化锌薄膜对甲基橙的光催化降解速率仅为金属锌膜还原降解速率的1/4左右,没有出现芳香族中间产物. 另外实验发现部分氧化的锌氧化物薄膜对甲基橙的光催化降解速率明显高于完全氧化的氧化锌薄膜,光催化活性的提高可能由于部分氧化薄膜中同时存在的金属锌及氧化锌相之间的协同效应.     

Effects of half-wave and full-wave power source on the anodic oxidation process on AZ91D magnesium alloy

Anodic films have been prepared on the AZ91D magnesium alloys in 1 mol/L Na₂SiO₃ with 10 vol.% silica sol addition under the constant voltage of 60 V at room temperature by half-wave and full-wave power sources. The weight of the anodic films has been scaled by analytical balance, and the thickness has been measured by eddy current instrument. The surface morphologies, chemical composition and structure of the anodic films have been characterized by scanning electron microscopy (SEM), energy dispersion spectrometry (EDS), X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that the thickness and weight of the anodic films formed by the two power sources both increase with the anodizing time, and the films anodized by full-wave power source grow faster than that by half-wave one. Furthermore, we have fitted polynomial to the scattered data of the weight and thickness in a least-squares sense with MATLAB, which could express the growth process of the anodic films sufficiently. The full-wave power source is inclined to accelerate the growth of the anodic films, and the half-wave one is mainly contributed to the uniformity and fineness of the films. The anodic film consists of crystalline Mg₂SiO₄ and amorphous SiO₂.     

Degradation of nitrobenzene-containing wastewater by carbon nanotubes immobilized nanoscale zerovalent iron

Nanoscaled zerovalent iron (NZVI)–multiwalled carbon nanotubes (CNTs) composite materials were prepared by in situ reduction of Fe²⁺ onto CNTs for nitrobenzene (NB) degradation. The morphologies and the composites of the prepared materials were characterized by SEM, TEM, and XRD. The results showed that the agglomeration of NZVI decreased with NZVI dispersed well onto the surfaces of CNTs, the particle size of NZVI on CNTs was about 20–50 nm. The BET surface areas of NZVI–CNTs was about 95.8 m²/g, which was 39 % higher than that of bare NZVI. For storage, the prepared NZVI–CNTs were concentrated into slurry and stored in situ as fresh slurry without drying. Contrast experiment results showed that the removal efficiency of NB by NZVI–CNTs fresh slurry was 30 % higher than that of vacuum-dried NZVI–CNTs, which indicates that storing in situ as fresh slurry can be an alternative strategy for nanoparticle storage. Batch experiment results showed that NB could be degraded to aniline by NZVI–CNTs rapidly, and the appropriate pH can be conducted at a relatively wide range from 2.0 to 9.0. The optimum mass ratio of iron–carbon was 1:1, and removal efficiency of NB by NZVI–CNTs with this mass ratio can achieve 100 % within 1 min. The degradation process of NB to intermediates was accelerated significantly by NZVI–CNTs, however, there was still a long term for the intermediates to transfer completely into the final product of aniline. The existence of CNTs can improve the formation of aniline through accelerating the electron transfer by forming microscopic galvanic cells with NZVI.