Influence of the Tl- and Hg-content on magnetic and transport properties of the Pb, Sr-doped Tl-1223 and Hg-1223 superconductors

The effects of the thallium and mercury content x on the as-sintered and post annealed samples of M_xPb_0.4Sr_1.6Ba_0.4Ca₂Cu₃O_8+δ {M: Tl (0.32≤x≤0.74) or Hg (0.18≤x≤0.68)} have been studied by magnetization and transport measurements. For Tl-1223 we have found the optimum Tl doping level to be x=0.53 regarding the grain properties, the content of superconducting phase, the first penetration field H_pl^wl, the transport (J_c^tr), magnetic intergrain (J_c^M) and intragrain (J_c^g) critical current densities. The critical temperature T_c of the as-sintered Tl-1223 sample decreased with increasing Tl content. Post-annealing in oxygen improved the T_c for Tl contents of x≥0.53 and had generally positive effects on the critical current densities. The intergrain properties of the Hg-1223 samples were much worse than those of the Tl-based superconductors.     

Granularity, microstructure, and flux creep in TlBa2Ca2Cu3O9+δ superconducting powder and silver-sheated tapes

Silver-sheathed TlBa₂Ca₂Cu₃O_9+δ (Tl-1223) tapes, with a transport critical current density, J_ct, of 6200 A/cm² at 75 K under zero magnetic field, were fabricated by the oxide-powder-in-tube (OPIT) method and characterized using an X-ray diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and superconducting quantum interference device (SQUID) magnetometer. The results of the magnetization and SEM study indicate that, in these tapes, individual grains are distributed randomly in orientation and weak links exist. However, strongly linked percolative current paths within the tape persisting in increasing fields, accompanied by strong intrinsic interplanar coupling, sustain a significant J_ct at high fields and lead to the plateau in the J_ct-H curve. Dislocation networks, which may act as effective pinning centers, are the common features observed in the tapes. To investigate the effects on flux pinning due to thermomechanical processing, magnetic relaxation at 1 and 2 T over 5–50 K was measured. The tape shows slightly lower normalized relaxation rates (S=-(1/M_o)dM/ dln t) than the cauliflower-like precursor powder. Analyses of the relaxation data obtained from the tape, after incorporating temperature dependence and field scaling, yield an expression for the effective pinning energy U_eff(J,T,H) = (U₁/H^0.54)[1-(T/ 72.5)²]⁴(J/J_i)^μ. This result was compared with the prediction of the collective flux-creep model, which suggests that Tl-1223 has a three-dimension-like (3D-like) vortex lattice. Presumably, a more plate-like powder morphology may result in improved texturing by the OPIT process. Tl_0.5Bi_0.5Sr₂CaCu₂O_7+δ ((Tl,Bi)-1212) powder with this morphology was therefore synthesized for comparison.     

Crystal structure of Tl0.5Pb0.5Sr2Ca2Cu3O9 at 300 K and around Tc (118 K)

The crystal structure including the cation distribution, of a polycrystalline sample of nominal composition Tl_0.5Pb_0.5Sr₂Ca₂Cu₃O₉ with T_c = 118.2 K has been determined using resonant synchrotron X-ray diffraction data collected at the Cu K, Tl L_III and Sr K edges and time-of-flight powder neutron diffraction data. No oxygen deficiency was observed, but cation disorder at all the non copper sites according to the formula (Tl_0.60Pb_0.40)(Sr_1.60Ca_0.40)(Ca_1.93Tl_0.07) Cu₃O₉ gives a mean hole concentration of 0.18(1) per Cu atom for the three CuO₂ planes, consistent with the high T_c for this material. Analysis of five time-of-flight powder neutron diffraction data between 80 and 150 K have revealed a possible discontinuity in the variation of the c lattice parameter at T_c, due to an anomaly in the position of the apical oxygen atoms.     

Surface atomic imaging of La2CuO4 and superconducting Tl2Ba2Ca2Cu3O10

Surface structures of the high T_c oxide superconductors Tl₂Ba₂Ca₂Cu₃O₁₀ and La₂CuO₄ have been studied by high resolution electron microscopy. In addition to the single atomic layer of La on the (113) surface observed previously, several atomic layers of the C-form of La₂O₃ were found to coat the (001) surfaces of La₂CuO₄. Surface reconstruction with the incorporation of excess Ba on the (110) surface of Tl₂Ba₂Ca₂Cu₃O₁₀ has been observed together with a stepped (11l) surface produced by a combination of the (110) and (001) planes. The (001) surface of Tl₂Ba₂Ca₂Cu₃O₁₀ was also found to terminate with a Ba-O layer. Possible mechanisms for the formation of these surface structures are discussed.     

The effects of substrate temperature on the superconducting properties of Tl2Ca2Ba2Cu3O10 films sputter-deposited from stoichiometric oxide targets

The annealing characteristics and the superconducting properties of Tl₂Ca₂Ba₂Cu₃O₁₀ thin films sputter-deposited onto yttrium- stabilized ZrO₂ substrate at up to 500°C from two stoichiometric oxide targets are reported. The films deposited at 400–500°C were found to require a lower post-annealing temperature than the films deposited at lower temperatures to attain the highest T_c superconducting state, due to a more pronounced Ba diffusion toward the substrate as indicated by their secondary ion mass spectrometry depth profiles. The highest T_c achieved tends to degrade with increasing substrate temperatures, a zero resistance T_c of 121 and ≈90 K, respectively, being observed for the films deposited at -ambient temperature and at 500°C. The formation of the highest T_c phase (Tl₂Ca₂Ba₂Cu₃O₁₀) generally is associated with a sheet type of crystal growth morphology with smooth and aligned surfaces which can be obtained only from the films capable of sustaining prolonged annealing at 900°C. Annealing at lower temperatures (≈860°C) results in the formation of rod or sphere type of morphologies with rough and randomly oriented crystals and the lower T_c phases such as Tl₂Ca₁Ba₂Cu₂O₈.     

Electrical transport and superconductivity in the Al2O3-Bi2Sr1.8Ca1.2Cu2Oy and MgO-Bi2Sr1.8Ca1.2Cu2Oy composites

We have measured the resistivities of Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites with the nominal Bi₂Sr_1.8Ca_1.2Cu₂O_y volume fraction, ₂₂₁₂, ranging from 0.15 to 1.00. For the Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu ₂O_y composites, we find for the samples with ₂₂₁₂≥0.6 that the superconducting transition temperature, T_c, is not disturbed by the addition of Al₂O₃. For ₂₂₁₂<0.3, no zero-resistivity state is observed. For the MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites, T_c is barely disturbed for the samples with ρ₂₂₁₂≥0.7. No superconducting state is observed for the samples with ρ₂₂₁₂<0.35. The variation of (300 K) with ρ₂₂₁₂ indicates a three-dimensional percolating Bi-Sr-Ca-Cu-O matrix occurring at ρ₂₂₁₂≈0.19 and ≈0.15 in Al₂O₃-Bi₂Sr_1.8Ca_1.2 Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y, respectively. Both resistivity and magnetization measurements suggest that the reactions of Bi₂Sr_1.8Ca_1.2Cu₂O_y with MgO are weaker than with Al₂O₃.     

High critical current density YBa2Cu3O7−δ tapes prepared by the surface-oxidation epitaxy method

YBa₂Cu₃O_7−δ (YBCO) films with high critical current density (J_c) were successfully fabricated on nickel tapes buffered with epitaxial NiO. NiO was prepared on the textured nickel tape by the surface-oxidation epitaxy (SOE) method. We have reported so far a critical temperature (T_c) of 87 K and J_c=4–6×10⁴ A/cm² (77 K, 0 T) for the YBCO films on NiO/Ni tapes. To enhance the superconducting properties of the YBCO films on the SOE-grown NiO, depositions of thin oxide cap layers such as YSZ, CeO₂, and MgO on NiO were investigated. These oxide cap layers were epitaxially grown on NiO and provided the template for the epitaxial growth of YBCO films. Substantially improved data of T_c=88 K and J_c=3×10⁵ A/cm² (77 K, 0 T) and 1×10⁴ A/cm² (77 K, Hc, 4 T) were obtained for YBCO film on NiO, by using a MgO cap layer with a thickness of 50 nm. The method described in this paper is a simple way to produce long YBCO tape conductors with high-J_c values.     

Zone melting of suspension spun Bi2Sr2Ca1Cu2Ox filament

Zone melting was used to enhance the J_c of suspension spun Bi₂Sr₂Ca₁Cu₂O_x filaments. By controlling the directional solidification of the molten zone, highly orientated textures were produced and a transport critical current density of more than 2 × 10⁴ A/cm² at 77 K, 0 T was achieved.     

Synthesis and properties of Hg0.7Pb0.3(BaSr)2Ca2Cu3Oz superconductors

We have synthesized Hg(Pb)-1223 with substitutions of Sr for Ba, i.e. Hg_0.7Pb_0.3Ba_2−xSr_xCa₂Cu₃O_z (x = 0.0–2.0) by the ampoule method. The spray-drying method and thermal decomposition under vacuum were applied for the preparation of homogeneous precursors. Samples with T_c = 110–128 K were obtained without oxygen annealing. We found that substitution of Ba by Sr remarkably relaxed the requirements on the precursors preparation and allowed their handling under ambient conditions.     

Fabrication, microstructure and critical current density of screen-printed Ag-(Bi, Pb)2Sr2Ca2Cu3Ox superconducting tapes

The influence of the sintering conditions on the microstructure and critical current density J_c has been studied on screen-printed Ag-(Bi, Pb)₂Sr₂Ca₂Cu₃O_x tapes with a ceramics mono-layer core. Three kinds of fabrication processes, which consist of a combination of cold working (rolling and/or pressing) and sintering, are applied. Four times repetition of pressing and sintering after the pre-sintering produces the highest c-axis alignment and achieves J_c= 1.5 × 10⁴ A/cm² (77 K, 0 T). The J_c versus θ data with an angle θ between B and the c-axis elucidate the relation between the anisotropy ratio γ=J_c(Bc)/J_c(B|c and the half-height angular width Δθ of a peak for Bc. This is related to both grain alignment and the J_c value. An increase in J_c, which comes from an improvement for grain alignment, enhances γ and narrows Δθ. The J_c versus θ data are fitted to the expression J_c(B, θ)=J _c(B, 90°)/[(γ−1)|cos θ|ⁿ+1] by regarding both γ and n as adjustable parameters. Fabrication of screen-printed tapes with multilayers (1≤N≤5) is presented, where the critical current increases from 8.0 A to 30.2 A at 77 K and 0 T as N increases.     

Temperature dependence of the critical current in YBa2Cu3O7−δ and Bi2Sr2Ca1Cu2O8 Josephson junctions

We have studied the stationary Josephson effect on YBa₂Cu₃O_7−δ (T_c=90 K) and Bi₂Sr₂Ca₁Cu₂ O₈ (T_c=80 K and 87 K for two samples of different origin) ceramic based junctions. The temperature dependence of the critical current near T_c has been found as I_c≈(T_c-T) for the Y-Ba-Cu-O samples indicating that they should be classified as S-N-I-N-S type junctions. The I-V curves of the Bi-Sr-Ca-Cu samples show the typical behaviour of S-I-S structures. Using Ambegaokar-Baratoff's theory for Bi₂Sr₂Ca₁Cu₂O₈, the temperature dependence of the superconducting state gap Δ(T) was calculated and it was evaluated that 1.452Δ(0)/k_BT_c3.5.     

Microwave absorption and paracoherence excess conductivity studies in high-Tc superconductors

Single phase polycrystalline samples of La_1.8Sr_0.2CuO₄, YBa₂Cu₃O_7−δ and Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_y high-T_c superconductors have been studied using XRD, SEM, EDAX, (T), χ_AC and EPR techniques. Detailed investigations on low-field-dependent microwave absorption have been carried out in order to investigate the effects of field exposure, field cooling, zero field cooling and amplitude of field variation on the samples. The results have been discussed on the basis of granular model via Josephson junctions of high-T_c superconductors. Over and above, paracoherence excess conductivity analysis has been carried out in all the three samples. The critical exponent (γ) estimated for all the three samples in close vicinity to their respective transition temperatures has an excellent agreement with the theoretically predicted value for 3-dimensional XY-ferromagnet (γ = 1.33 for D = 3, N = 2).     

Trapping mechanism of superconductivity suppression induced by Pr substitution in the Ho1−xPrxBa2Cu3O7−δ system

Pr concentration dependence of the superconducting transition temperature T_c in the Ho_1−xPr_xBa₂Cu₃O_7−δ system is determined from measurements of DC electrical resistance. This dependence coincides with that for the parallely studied Y_1−xPr_xBa₂Cu₃O_7−δ reference system. Both systems have the same value of the critical concentration x_c=0.58, in accordance with nearly equal ionic radii of Ho³⁺ and Y³⁺ ions. It has been shown that the T_c(x) curve can be described with a single mechanism based on a decreasing number of sheet holes trapped by Pr^IV-ions, if one takes also into account that the number of these ions changes with x.     

Critical current density of rolled silver-sheathed Bi(2223) tapes

Silver-sheathed (Bi,Pb)₂Sr₂Ca₂Cu₃O_x (Bi(2223)) tapes were fabricated by the “oxide-powder-in-tube” technique. After the tapes were shaped and sintered, an additional cold rolling and a re-sintering were applied in order to enhance the critical current density J_c. The influence of the additional rolling conditions (roll diameter, number of passes, lubrication) on the J_c (77 K, 0 T) was made clear. The influence of the sintering conditions (temperature, heating rate) on J_c was also investigated. As for the rolling conditions, a small redundant shear deformation or a small contact angle leads to a good grain alignment, texturing, and a higher J_c value. As for the temperature of the first sintering, 1113 K is superior to 1118 K because of the volume fraction of the Bi(2223) phase.     

Oxyanion derivatives of cuprate superconductors superconducting 123 phosphates

While YSr₂Cu₃O₇ cannot be prepared under ambient conditions, partial substitution of the phosphate group for copper, as in YSr₂Cu_2.8(PO₄)_0.2O_y, stabilizes this phase in the orthorhombic structure, but the material is not superconducting. Superconductivity in YSr₂Cu_2.8(PO₄)_0.2O_y is obtained by increasing the hole concentration through partial substitution of Y by Ca, as in Y_0.7Ca_0.3Sr₂Cu_2.8(PO₄)_0.2O_y (T_c≈40 K). By incorporating the phosphate group in orthorhombic YBaSrCu₃O ₇, a stable tetragonal derivative of the formula YBaSrCu_2.8(PO₄)_0.2O_y (T_c≈ 47 K) has been prepared; the T_c increases to 70 K by partial substitution of Y by Ca as in Y_0.7Ca_0.3BaSrCu_2.8(PO₄)_0.2O_y.     

Laser ablated bismuth cuprate thin films preparation and effect of oxygen nonstoichiometry upon superconductivity

Thin films of Bi₂Sr₂CaCu₂O₈ and (Bi, Pb)₂Sr₂Ca₂Cu₃O₁₀ have been prepared on monocrystalline (100) MgO substrates, using a laser ablation method with post annealing treatment. The influence of substrate temperature and oxygen pressure during deposition were investigated. SEM observations, EDS analysis, electric and magnetic measurements have been used to characterize the films. Superconducting “2212” films, with T_c(R = 0) at 80–83 K and J_c (50 K) up to 5 × 10⁵ A/cm², have been currently achieved, while Pb-doped “2223” films exhibit T_c as high as 110 K with J_c = 5 × 10⁴ A/cm² at 77 K. The effect of annealing at low temperature (350°C) in an argon flow has been studied for the 2212 phase, it shows the influence of the oxygen non-stoichiometry, i.e. of the hole carrier density upon T_c's which can be measured up to 89 K (zero resistance).     

Effective activation energy Ue(T,J,H) in textured Bi1.84Pb0.4Sr2Ca2Cu3Oy silver-clamped thick films

We have measured the resistivity of textured Bi_1.84Pb_0.4Sr₂Ca₂Cu₃O_y silver-clamped thick films as a function of temperature, current density ranging from 10 to 1×10³ A/cm² and magnetic field up to 0.3 T. We find that the effective activation energy U_e follows U_e(T,J,H)=U₀(1−T/T_p)^mln(J_c0/J)H⁻ with m=1.75 for Hab-plane and 2.5 for Hc-axis and =0.76 for Hab and 0.97 for Hc, for the current density regime above 100 A/cm², where T_p is a function of applied magnetic field and current density. This result suggests the effective activation energy U_e be correlated with the temperature, current density and magnetic field. The possible dissipative mechanisms responsible for the temperature, current density and magnetic field dependence of the effective activation energy are discussed.     

NMR study of local hole distribution, spin fluctuation and superconductivity in Tl2Ba2Ca2Cu3O10

⁶³Cu, ¹⁷O and ²⁰⁵Tl NMR have been performed in the high-T_c superconductor Tl₂Ba₂Ca₂Cu₃O₁₀ whose T_c(max) is 127 K. The hole densities at Cu and oxygen sites in the CuO₂ plane have been extracted from the nuclear quadrupole frequency ν_Q. The striking feature is that the Cu holes are significantly transferred to oxygen site due to strong hybridization between Cu and oxygen. From an analysis of T₁ and T_2G, it has been found that the spectral weight of the spin fluctuation is transferred to higher energy compared to YBa₂Cu₃O₇, while the magnetic correlation length ξ does not differ much. Thus, it is suggested that the higher T_c is due to higher characteristic energy of spin fluctuations, i.e. the superconductivity is spin fluctuation mediated. The superconducting properties are consistently explained by a d-wave superconductivity model with a finite density of states (DOS) at the Fermi level. We show that the disorder of the Ca/TlO layer caused by the partial inter-substitution of Tl and Ca is responsible for the potential scattering to produce such a DOS. It is found that if such a potential scattering were absent, T_c would go up to 132 K which is quite close to the record T_c realized in the Hg based compound.     

Preparation of melt-textured NdBa2Cu3Oy bulk with Nd4Ba2Cu2O10 addition

The NdBa₂Cu₃O_y (Nd123) bulk superconductor, to which Nd₄Ba₂Cu₂O₁₀ (Nd422) particles were intentionally added, was prepared through the so-called MMTG process in Ar (99% purity) flowing atmosphere at an ambient pressure. The quasi-single crystal thus grown was about 1 cm × 1 cm × 1 cm in dimension. It turned out that the Nd422 particles were uniformly distributed in the Nd123-phase matrix in a fashion similar to the distribution of the intentionally added Y211 particles in the Y123 phase matrix. The superconducting transition temperature T_c for the sample subjected to post-annealing in oxygen atmosphere was 94 K. The critical current density J_c was determined to be 45 000 A/cm² at 77 K and 1 T, when the field was applied parallel to the c-axis of the sample. To the best of our knowledge, the J_c value is the highest and the size of the quasi-single crystal is the largest in the melt-textured Nd123 bulk superconductors so far reported.     

The effect of gallium substitution on the superconductivity of the BiSrCaCuO system

Magnetic susceptibility, X-ray diffraction and resistivity measurements of the system Bi_1.4Pb_0.6Sr₂Ca_2−xGa_xCu₃O_y are reported for 0 x 2. The high-T_c 2223 phase with a T_c of 107 K for x = 0 exists for x 0.3. The low-T_c 2212 phase with a T_c of 75 K for x = 0 exists for the full range of x. The highest values of the critical temperature and the largest volume fraction of the low-T_c phase in compounds with Ga occur for x = 0.5 ± 0.1. The identification of CaO by X-ray diffraction for x 0.6 indicates that Ga replaces Ca in the compound.