Heterogeneous adsorption and catalytic oxidation of benzene, toluene and xylene over spent and chemically regenerated platinum catalyst supported on activated carbon

The heterogeneous adsorption and catalytic oxidation of benzene, toluene and o-xylene (BTX) over the spent platinum catalyst supported on activated carbon (Pt/AC) as well as the chemically treated spent catalysts were studied to understand their catalytic and adsorption activities. Sulfuric aqueous acid solution (0.1N, H₂SO₄) was used to regenerate the spent Pt/AC catalyst. The physico-chemical properties of the catalysts in the spent and chemically treated states were analyzed by using nitrogen adsorption-desorption isotherm and elemental analysis (EDX). The gravimetric adsorption and the light-off curve analysis were employed to study the BTX adsorption and oxidation on the spent catalyst and its modified Pt/AC catalysts. The experimental results indicate that the spent Pt/AC catalyst treated with the H₂SO₄ aqueous solution has a higher toluene adsorption and conversion ability than that of the spent Pt/AC catalyst. A further studies of H₂SO₄ treated Pt/AC catalyst on their catalytic and heterogeneous adsorption behaviours for BTX revealed that the activity of the H₂SO₄ treated Pt/AC catalyst follows the sequence of benzene > toluene > o-xylene. The adsorption equilibrium isotherms of BTX on the H₂SO₄ treated Pt/AC were measured at different temperatures ranging from 120 to 180 °C. To correlate the equilibrium data and evaluate their adsorption affinity for BTX, the two sites localized Langmuir (L2m) isotherm model was employed. The heterogeneous surface feature of the H₂SO₄ treated Pt/AC was described in detail with the information obtained from the results of isosteric enthalpy of adsorption and adsorption energy distributions. Furthermore, the activity of H₂SO₄ treated Pt/AC about BTX was found to be directly related to the Henry's constant, isosteric enthalpy of adsorption and adsorption energy distribution functions.     

Influence of the thickness of sputter-deposited platinum films on the electrochemical promotion of propane combustion

8 to 120 nm-thick Pt coatings were sputter-deposited on Yttria-Stabilised Zirconia (YSZ) membranes, 17 mm in diameter, by magnetron sputtering of a Pt target at low pressure (0.3 Pa). The catalytic activity of propane combustion under open-circuit conditions is first measured near to the stoichiometry (0.2%C₃H₈/1%O₂) and shows that the coatings present a rather high catalytic activity. Close-circuit measurements were finally performed at 337 °C and 400 °C. They show that rather high faradaic efficiencies in the range 10⁶ can be reached as soon as the Pt film is thick enough to allow a bias of its whole area. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

The relationship of the catalytic activity and the open-circuit potential of Pt interfaced with YSZ

This study deals with the relationship between open-circuit potential and catalytic activity of the system Pt/YSZ. Temperature-programmed desorption (TPD) of oxygen was carried out in order to investigate the link between the oxygen coverage and the potential. Then, catalytic activity in parallel with the potential value was measured between 200 °C and 500 °C for NO oxidation, C₃H₈ combustion, C₃H₆ combustion and the selective catalytic reduction (SCR) of NO by C₃H₆ in the presence of oxygen. It was found that potential measurement can give precious information on the competitive adsorption between oxygen and other reactants. Finally, it seems to be also a good way to anticipate the NEMCA behavior for reactions, which involve oxygen. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Preparation and characterization of Pt-supported porous graphite nanofibers

In this work, porous graphite nanofibers (PGNFs) were manufactured as promising catalyst supporter by a physical activation method for direct methanol fuel cells, and Pt nanoparticles were loaded on the PGNFs in order to prepare electrode materials by a chemical reduction method. The pore structures of the Pt/PGNFs were analyzed by N₂ adsorption isotherms at 77 K. Electrocatalytic activities of final products were investigated by voltammetry and conductivity measurements in a 1.0 M CH₃OH/0.5 M H₂SO₄. As a result, electrocatalytic activities of Pt/PGNFs were increased in the presence of Pt particles on the PGNFs and with increasing the specific surface area of the carbons.     

Large single-crystal monolayer graphene by decomposition of methanol

We present a novel method for the synthesis of monolayer graphene with large single-crystal domains extending over 10–30 μm², produced by the decomposition of methanol on Cu in a single process step, in a flow of pure Ar gas, without H₂. Eliminating H₂ as a process gas offers increased safety and greatly facilitates fabrication scaling. The graphene grain size and orientation were characterized by selected area electron diffraction in transmission electron microscopy. Based on analyses of effluents from the furnace during the synthesis, a possible mechanism for graphene formation from methanol, involving carbon monoxide as an intermediate, is proposed.     

Synthesis and enhanced photocatalytic activity of NaNbO3 prepared by hydrothermal and polymerized complex methods

We prepared NaNbO₃ by several methods, namely solid-state reaction (SSR), hydrothermal (HT) and polymerized complex (PC) methods, and investigated the relationships between the photocatalytic activity and the particle size and morphology. The photocatalytic activity was evaluated by H₂ evolution from an aqueous methanol solution and pure water splitting in the presence of the Pt(0.5 wt%)/NaNbO₃ and RuO₂(1.25 wt%)/NaNbO₃, respectively. It is found that the sample prepared by PC with smallest particles exhibits the highest photocatalytic activity in both reactions. Moreover, the HT sample with the cubic and rectangular shape also shows the enhanced photocatalytic activity for H₂ evolution from an aqueous methanol solution in comparison with that of the sample prepared by SSR.     

Sodium superionic conductor sputter-deposited coatings

Thin sodium superionic conductor (Nasicon) coatings are deposited on rotating substrates by co-sputtering in the reactive mode of a Zr-Si and a Na₃PO₄ target. The influence of the discharge current and of the target-to-substrate distance is investigated owing to the targeted Na₃Zr₂Si₂PO₁₂ stoichiometry. A thermo-structural analysis shows that the amorphous as-deposited coating of convenient composition crystallises around 700 °C in the monoclinic structure. Electrical measurements performed at room temperature after various annealing treatments indicate a ionic conductivity of about 2·10⁻³ S·cm⁻¹, consistent with that of bulk Nasicon. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14 – 18, 2004.     

Effect of Fe state on electrocatalytic activity of Pd-Fe/C catalyst for oxygen reduction

The carbon-supported Pd-Fe catalyst (Pd-Fe/C) is prepared in the H₂O/tetrahydrofuran (THF) mixture solvent under the low temperature. The homemade Pd-Fe/C catalyst contains two forms of iron species, alloying and non-alloying Fe. The alloying Fe species is hardly dissolved in 0.5 M H₂SO₄ solution, while the non-alloying Fe species is easily dissolved in 0.5 M H₂SO₄ solution. The electrochemical measurements show the electrocatalytic activity of the Pd-Fe/C catalyst with the acid treatment for the oxygen reduction is higher than that of the Pd-Fe/C catalyst without the acid treatment, illustrating that the non-alloying Fe species suppresses the electrocatalytic activity of the Pd-Fe/C catalyst. In contrast, the alloying Fe species promotes the electrocatalytic activity of the Pd-Fe/C catalyst for the oxygen reduction, which is likely attributed to the change of the electron structure of Pd atom and/or bond length of Pd-Pd in the Pd-Fe/C catalyst.     

D.C. conductivity of transparent conductive ZnO:Al films in the temperature range 80–360 K

An experimental study of the temperature dependence of the d.c. conductivity σ as a function of temperature T in the range from 80–360 K on nanocrystalline ZnO:Al films (Al³⁺ 2%) of thickness 500 nm prepared on glass microscope slides by a dip — coating method is presented. The electrical conductivity σ, which at room temperature varied between 0.1 to 2.7 S/cm, increased almost linearly with T for all the samples. Measurements of the Hall coefficient at room temperature and in a magnetic field of 1.2 T, gave R_H=0.53 cm³C⁻¹, from which a carrier concentration of n=1.18×10¹⁹ cm⁻³ and a carrier mobility of μ=1.40 cm²/Vs were deduced. Paper presented at the Patras Conference on Solid State Ionics — Transport Properties, Patras, Greece, Sept. 14–18, 2004.