Structural and optical analysis of 60Co gamma-irradiated thin films of polycrystalline Ga10Se85Sn5

The present study focuses on the effects of gamma irradiation on structural and optical properties of polycrystalline Ga₁₀Se₈₅Sn₅ thin films with a thickness of ～300?nm deposited by the thermal evaporation technique on cleaned glass substrates. X-ray diffraction patterns of the investigated thin films show that crystallite growth occurs in the orthorhombic phase structure. The surface study carried out by using the scanning electron microscope (SEM) confirms that the grain size increases with gamma irradiation. The optical parameters were estimated from optical transmission spectra data measured from a UV–vis-spectrophotometer in the wavelength range of 200–1100?nm. The refractive index dispersion data of the investigated thin films follow the single oscillator model. The estimated values of static refractive index n₀, oscillator strength E_d, zero frequency dielectric constant ε₀, optical conductivity σ_optical and the dissipation factor increases after irradiation, while the single oscillator energy E_o decreases after irradiation. It was found that the value of the optical band gap of the investigated thin films decreases and the corresponding absorption coefficient increases continuously with an increase in the dose of gamma irradiation. This post irradiation changes in the values of optical band gap and absorption coefficient were interpreted in terms of the bond distribution model.     

Optical properties of amorphous HF–In–Zn–O thin films estimated from transmission spectra

Amorphous and flat (<1 nm roughness) Hf–In–Zn–O thin films were prepared by radio frequency (rf) magnetron sputtering method at room temperature (RT) and at 300 °C substrate temperature. The crystal structure and surface morphology were investigated by high resolution X-ray diffraction (HR-XRD) and atomic force microscopy (AFM), respectively. Optical properties of these films were obtained from the UV–VIS–NIR transmission spectra, at normal incidence, over the 200–2000 nm spectral range. Swanepoel's method was used to calculate the thickness and the refractive index of the films. The dispersion of refractive index was obtained in terms of the single-oscillator Wemple–DiDomenico model. The optical absorption edge was described using the direct transition model proposed by Tauc. The film deposited at higher substrate temperature had lower optical band gap, higher refractive index, higher oscillator strength and energy of the effective dispersion oscillator. Optical characterization shows that films become more stable, relaxed and rigid at higher substrate temperature.     

Structural and optical properties of thermally evaporated 2-(2,3-dihydro-1,5-dimethyl-3-oxo-2-phenyl-1H-pyrazol-4-ylimino)-2-(4-nitrophenyl)acetonitrile thin films

The structural and optical properties of as-deposited and γ-rays irradiated 2-(2,3-dihydro-1,5dimethyl-3-oxo-2-phenyl-1H-pyrazol-4-ylimino)-2-(4-nitrophenyl)acetonitrile (DOPNA) thin films have been reported. The structural properties of as-deposited and γ-rays irradiated DOPNA thin films are characterized by Fourier transformation infrared, X-ray diffraction and transmission electron microscope techniques. The transmittance, T(λ), and reflectance, R(λ), are measured at the normal incidence of light by a double beam spectrophotometer in the wavelength range 200-2200 nm. The refractive and absorption indices have been calculated. The dispersion parameters such as dispersion energy, oscillator energy and dielectric constant at high frequency are evaluated. The data of the absorption coefficient are analyzed in order to determine the type of inter-band electronic transitions and the optical band gap of the films. Other optical absorption parameters, namely, the extinction molar coefficient, oscillator strength and the electric dipole strength, are also calculated.     

Determination and analysis of dispersive optical constants of CuIn3S5 thin films

CuIn₃S₅ thin films were prepared from powder by thermal evaporation under vacuum (10⁻⁶ mbar) onto glass substrates. The glass substrates were heated from 30 to 200 °C. The films were characterized for their optical properties using optical measurement techniques (transmittance and reflectance). We have determined the energy and nature of the optical transitions of films. The optical constants of the deposited films were determined in the spectral range 300-1800 nm from the analysis of transmission and reflection data. The Swanepoel envelope method was employed on the interference fringes of transmittance patterns for the determination of variation of refractive index with wavelength. Wemple-Di Domenico single oscillator model was applied to determine the optical constants such as oscillator energy E₀ and dispersion energy E_d of the films deposited at different substrate temperatures. The electric free carrier susceptibility and the ratio of the carrier concentration to the effective mass were estimated according to the model of Spitzer and Fan.     

Structural, morphological and optical properties of CuAlS2 films deposited by spray pyrolysis method

The structural, morphological and optical properties of CuAlS₂ films deposited by spray pyrolysis method have been investigated. CuAlS₂ in the form of films is prepared at different deposition conditions by a simple and economical spray pyrolysis method. The structural, surface morphology and optical properties of the films were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscope (AFM) and absorbance spectra, respectively. The films were polycrystalline, crystallized in a tetragonal structure, and are preferentially orientated along the (1 1 2) direction. Grain size values, dislocation density, and d% error of CuAlS₂ films were calculated. The optical band gap of the CuAlS₂ film was found to be 3.45 eV. The optical constants such as refractive index, extinction coefficient and dielectric constants of the CuAlS₂ film were determined. The refractive index dispersion curve of the film obeys the single oscillator model. Optical dispersion parameters E_o and E_d developed by Wemple-DiDomenico were calculated and found to be 3.562 and 12.590 eV.     

Formation of Ge35In8S57 amorphous films for optical applications

Thin films of In-doped Ge-S in the form of Ge₃₅In₈S₅₇ with different film thickness were deposited using an evaporation method. The X-ray diffraction studies demonstrate that the as-prepared films are amorphous in nature for these films. Some optical constants were calculated at a thickness of 150, 300, 450 and 900?nm and annealing temperature of 373, 413, 437 and 513?K. Our optical observations show that the mechanism of the optical transition obeys the indirect transition. It was found that the energy gap, E_g, decreases from 2.44 to 2.20?eV with expanding the thickness of the film from 150 to 900?nm. On the other hand, it was found that E_g increases with annealing temperature from 373 to 513?K. The increment in the band gap can be attributed to the gradual annealing out of the unsaturated bonds delivering a decreasing the density of localized states in the band structure. Using the single oscillator model, the dispersion of the refractive index is described. The dispersion constants of these films were calculated with different both thickness and annealing temperatures. Additionally, both of nonlinear susceptibility, χ⁽³⁾ and nonlinear refractive index, n₂ were calculated.     

Optimization of the optical and electrical properties of electron beam evaporated aluminum-doped zinc oxide films for opto-electronic applications

Aluminum-doped zinc oxide (AZO) thin films have been deposited by electron beam evaporation technique on glass substrates. The structural, electrical and optical properties of AZO films have been investigated as a function of annealing temperature. It was observed that the optical properties such as transmittance, reflectance, optical band gap and refractive index of AZO films were strongly affected by annealing temperature. The transmittance values of 84% in the visible region and 97% in the NIR region were obtained for AZO film annealed at 475 °C. The room temperature electrical resistivity of 4.6×10⁻³ Ω cm has been obtained at the same temperature of annealing. It was found that the calculated refractive index has been affected by the packing density of the thin films, whereas, the high annealing temperature gave rise to improve the homogeneity of the films. The single-oscillator model was used to analyze the optical parameters such as the oscillator and dispersion energies.     

Thickness dependent optical dispersion parameters and nonlinear optical properties of nanostructured Cr doped CdO thin films

Cr doped CdO thin films were deposited on glass substrates by reactive DC magnetron sputtering with varying film thickness from 250 to 400 nm. XRD studies reveal that the films exhibit cubic structure with preferred orientation along the (2 0 0) plane. The optical transmittance of the films decreases from 92 to 72%, whereas the optical energy band gap of the films decreased from 2.88 to 2.78 eV with increasing film thickness. The Wemple–DiDomenico single oscillator model has been used to evaluate the optical dispersion parameters such as dispersion energy (E_d), oscillator energy (E_o), static refractive index (n_o) and high frequency dielectric constant (ε_∞). The nonlinear optical parameters such as optical susceptibility (χ⁽¹⁾), third order nonlinear optical susceptibility (χ⁽³⁾) and nonlinear refractive index (n₂) of the films were also determined.     

Microstructure parameters and optical properties of cadmium ferrite thin films of variable thickness

CdFe₂O₄ thin films of different thicknesses were deposited onto glass substrates by the thermal evaporation technique. Their structural characteristics were studied by X-ray diffraction (XRD). The microstructure parameters, crystallite size, and microstrain were calculated. It is observed that both the crystallite size increases and microstrain increase with increasing with the film thickness. The fundamental optical parameters like absorption coefficient and optical band gap are calculated in the strong absorption region of transmittance and reflectance spectrum. The refractive indices have been evaluated in terms of the envelope method, which has been suggested by Swanepoel in the transparent region. The refractive index can be extrapolated by the Cauchy dispersion relationship over the whole spectra range, which extended from 400 to 2500 nm. The refractive index, n, increases on increasing the film thickness up to 733 nm and the variation of n with higher thickness lies within the experimental errors.     

Preparation of ZnO-doped Al films by spray pyrolysis technique

Al-doped zinc oxide (AZO) thin films have been prepared by spray pyrolysis (SP) technique of zinc acetate and aluminium nitrate, and the effect of thickness on structural and optical properties has been investigated. The structural and optical characteristics of the AZO films were examined by X-ray diffraction (XRD) and double-beam spectrophotometry. These films, deposited on glass substrates at an optimal substrate temperature (T_S = 450 °C), have a polycrystalline texture with a hexagonal structure. Transmission measurements showed that for visible wavelengths, the AZO films have an average transmission of over 90%. The optical parameters have been calculated. The dependence of the refractive index, n, and extinction coefficient, k, on the wavelength for the sprayed films is also reported. Optical band gap of AZO is 3.30 and 3.55 eV, respectively, depending on the film thicknesses.     

Derivation of the optical constants of spin coated CeO2-TiO2-ZrO2 thin films prepared by sol-gel route

Ternary thin films of cerium titanium zirconium mixed oxide were prepared by the sol-gel process and deposited by a spin coating technique at different spin speeds (1000-4000 rpm). Ceric ammonium nitrate, Ce(NO₃)₆(NH₄)₂, titanium butoxide, Ti[O(CH₂)₃CH₃]₄, and zirconium propoxide, Zr(OCH₂CH₂CH₃)₄, were used as starting materials. Differential calorimetric analysis (DSC) and thermogravimetric analysis (TGA) were carried out on the CeO₂-TiO₂-ZrO₂ gel to study the decomposition and phase transition of the gel. For molecular, structural, elemental, and morphological characterization of the films, Fourier Transform Infrared (FTIR) spectral analysis, X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), cross-sectional scanning electron microscopy (SEM), and atomic force microscopy (AFM) were carried out. All the ternary oxide thin films were amorphous. The optical constants (refractive index, extinction coefficient, band gap) and thickness of the films were determined in the 350-1000 nm wavelength range by using an nkd spectrophotometer. The refractive index, extinction coefficient, and thickness of the films were changed by varying the spin speed. The oscillator and dispersion energies were obtained using the Wemple-DiDomenico dispersion relationship. The optical band gap is independent of the spin speed and has a value of about E_g≈2.82±0.04 eV for indirect transition.     

Influence of thickness and annealing on linear and nonlinear optical properties of manganese (III) chloride tetraphenyl porphine (MnTPPCl) organic thin films

Thin films of manganese (III) chloride 5,10,15,20-tetraphenyl-21H,23H-porphine (MnTPPCl) with different film thickness were deposited by an evaporation technique. Some optical constants were calculated for these films at a thickness of 110, 220 and 330 nm and annealing temperature of 373 and 437 K. IR spectrum demonstrating that the thermal evaporation method is a good one to acquire undissociated and stoichiometric MnTPPCl films. Our perceptions demonstrate that the mechanism of the optical absorption obeys with the indirect transition. It was found that the energy gap, E_g, affected by the film thickness and annealing. Dispersion of the refractive index is described using single oscillator model. Dispersion parameters are calculated as a function of the film thickness and annealing temperature. In addition, the third-order nonlinear susceptibility, χ⁽³⁾, and the nonlinear refractive index, n₂, were calculated.     

金属有机分解法制备的SrTiO3薄膜的光学特性

采用金属有机分解法（MOD）在石英衬底上沉积了SrTiO3薄膜。所制备的薄膜是晶格常数为a=b=c=3.90?的多晶结构。通过测量190—1100nm波段内的透射光谱，采用包络方法计算了薄膜的光学常数（折射率n和消光系数k）。结果表明，采用MOD方法制备的薄膜的折射率大于采用射频磁控溅射、溶胶—凝胶和化学气相沉积方法制备的薄膜的折射率；薄膜的折射率色散关系满足单振子模型，其中振子强度S0为0.88′1014m-2，振子能量E0为6.40eV；薄膜的禁带宽度为3.68eV。     

Structural and optoelectronic properties of amorphous GaN thin films

Amorphous gallium nitride (a-GaN) thin films were deposited on glass substrate by electron beam evaporation technique at room temperature and high vacuum using N ₂ as carrier gas. The structural properties of the films was studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). It was clear from XRD spectra and SEM study that the GaN thin films were amorphous. The absorbance, transmittance and reflectance spectra of these films were measured in the wavelength range of 300–2200 nm. The absorption coefficient spectral analysis in the sharp absorption region revealed a direct band gap of E _g = 3:1 eV. The data analysis allowed the determination of the dispersive optical parameters by calculating the refractive index. The oscillator energy E ₀ and the dispersion energy E _d, which is a measure of the average strength of inter-band optical transition or the oscillator strength, were determined. Electrical conductivity of a-GaN was measured in a different range of temperatures. Then, activation energy of a-GaN thin films was calculated which equalled E _a = 0:434 eV.     

Effect of incorporating nonlanthanoidal indium on optical properties of ferroelectric Bi4Ti3O12 thin films

Bi₄Ti₃O₁₂ (BTO) and Bi_3.25In_0.75Ti₃O₁₂ (BTO:In) thin films were prepared on fused quartz and LaNiO₃/Si (LNO) substrates by chemical solution deposition (CSD). Their microstructures, ferroelectric and optical properties were investigated by X-ray diffraction, scanning electron microscope, ferroelectric tester and UV-visible-NIR spectrophotometer, respectively. The optical band-gaps of the films were found to be 3.64 and 3.45 eV for the BTO and BTO:In films, respectively. Optical constants (refractive indexes and extinction coefficients) were determined from the optical transmittance spectra using the envelope method. Following the single electronic oscillator model, the single oscillator energy E₀, the dispersion energy E_d, the average interband oscillator wavelength λ₀, the average oscillator strength S₀, the refractive index dispersion parameter (E₀/S₀), the chemical bonding quantity β, and the long wavelength refractive index n_∞ were obtained and analyzed. Both the refractive index and extinction coefficient of the BTO:In films are smaller than those of the BTO films. Furthermore, the refractive index dispersion parameter (E₀/S₀) increases and the chemical bonding quantity β decreases in the BTO and BTO:In films compared with those of bulk.     

Structural and optical evaluation of WOxNy films deposited by reactive magnetron sputtering

Thin films of tungsten oxynitrides were deposited on substrates preheated at 300 °C from metallic tungsten target using reactive pulsed d.c. magnetron sputtering. The deposition was carried out at different nitrogen to total reactive gas partial pressures ratios. The energy dispersive analysis of X-ray showed that significant incorporation of nitrogen occurred only when the nitrogen partial pressure exceeded 74% of the total reactive gas pressure. X-ray diffraction analysis revealed that the formation of a specific crystalline phase is affected by the composition and the possibility of competitive growth of different phases. The increase of nitrogen content into the films increases the optical absorption and decreases the optical band gap. The refractive index was determined from the transmittance spectra using Swanepoel's method. It was found that the refractive index increases with increasing nitrogen content over the entire spectral range. The values of the tungsten effective coordination number, N_c, was estimated from the analysis of the dispersion of the refractive index, and an increase in N_c with increasing nitrogen content was observed.     

Structure-related infrared optical properties of BaTiO3 thin films grown on Pt/Ti/SiO2/Si substrates

BaTiO₃ thin films with different thickness have been grown on Pt/Ti/SiO₂/Si substrates by a modified sol-gel method. X-ray diffraction analyses show that the BaTiO₃ thin films are polycrystalline. The crystalline quality of the films is improved with increasing thickness. The infrared optical properties of the BaTiO₃ thin films have been investigated using an infrared spectroscopic ellipsometry in the wave number range of 800-4000 cm⁻¹ (2.5-12.5 μm). By fitting the measured pseudodielectric functions with a three-phase model (Air/BaTiO₃/Pt), and a derived classical dispersion relation for the thin films, the optical constants and thicknesses of the thin films have been simultaneously obtained. The refractive index of the BaTiO₃ thin films increases and on the other hand, the extinction coefficient does not change with increasing thickness in the entirely measured wave number range. The dependence of the refractive index on the film thickness has been discussed in detail and was mainly due to both the crystalline quality of the films and packing density. Finally, the absorption coefficient was calculated in the infrared region for applications in the pyroelectric IR detectors.     

蓝宝石表面处理对氮化镓光学性质的影响

采用化学方法腐蚀部分c面蓝宝石衬底,在腐蚀区域形成一定的图案,利用LP-MOCVD在经过表面处理的蓝宝石衬底上外延生长GaN薄膜.利用GaN薄膜光学透射谱,结合椭偏测量得到的折射率色散公式,计算得到GaN薄膜厚度,与椭偏光谱结果几乎一致;在经过表面处理的蓝宝石衬底上外延生长的GaN薄膜表现出更优异的光学质量和结晶质量,其透射谱具有更高的透射率和更大的调制深度,而且其光致发光谱中的黄光带几乎可以忽略.     

Thin films of asymmetrically substituted “ABAB-Type” indium phthalocyanine chloride: Preparation, structural characterization and optical properties

A synthetic route to the asymmetric octasubstituted metal-free phthalocyanines H₂Pcs (3-8) has been developed. They contain a combination of 2(3),16(17)-Tetra(2-ethyl-1-hexyl) and 9(10),23(24)-tetra(n-hexyl) as substituent groups in the peripheral positions. Thin films of the target asymmetric substituted “ABAB-Type” indium phthalocyanine chloride complex InPcCl 9, have been also fabricated for the first time, with different thickness (105-350 nm) using thermal evaporation technique. The structural and optical properties of the films have been investigated. The material in powder form showed a polycrystalline nature with triclinic structure. Miller indices, hkl, values for each diffraction line in X-ray diffraction (XRD) spectrum were calculated. The as-deposited films exhibited also a crystalline nature with a preferred orientation of growth. The scanning electron microscope showed the nano-structure property of the deposited films. The optical properties of the films are studied by the spectrophotometric measurements of the transmittance, T and the reflectance, R determined at the normal incident of the light in the spectral range 200-2500 nm. The refractive and absorption indices of the films are calculated and are found to be independent of film thickness of 105-350 nm. Different dispersion and absorption parameters are determined for the films.