Z-scan study of third-order optical nonlinearities in bismuth-based glasses

The third-order optical nonlinearity was measured in bismuth-based glasses by Z-scan technique using femto-second laser pulses. Re(χ⁽³⁾) = 4.9 × 10⁻¹¹ esu at 748 nm was obtained in the glass containing 65.5 mol% of Bi₂O₃. Although, the wavelength dependence of Re(χ⁽³⁾) shows resonant effect significantly, relatively small nonlinear absorption coefficient β = 0.8 cm/GW at 769 nm was estimated. Bismuth-based glass exhibits the largest third-order optical nonlinearity in oxide glasses, indicating they are promising materials used for nonlinear optical devices.     

Picosecond nonlinear optical response of Ba0.5Sr0.5TiO3 thin films fabricated by pulsed laser deposition

Well-crystallized Ba_0.5Sr_0.5TiO₃ thin films with good surface morphology were prepared on MgO(1 0 0) substrates by pulsed laser deposition technique at a deposition temperature of 800 °C under the oxygen pressure of 2 × 10⁻³ Pa. X-ray diffraction and atomic force microscopy were used to characterize the films. The full width at half maximum of the (0 0 2) Ba_0.5Sr_0.5TiO₃ rocking curve and the root-mean-square surface roughness within the 5 μm × 5 μm area were 0.542° and 0.555 nm, respectively. The nonlinear optical properties of the films were determined by a single beam Z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that Ba_0.5Sr_0.5TiO₃ thin films exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 5.04 × 10⁻⁶ cm²/kW and β = 3.59 × 10⁻⁶ (m/W), respectively.     

Characterization of optical and nonlinear optical properties of silver nanoparticles prepared by laser ablation in various liquids

The optical, structural, and nonlinear optical properties of silver nanoparticles prepared by laser ablation in various liquids were investigated at 397.5, 532, and 795 nm. The TEM and spectral measurements have shown temporal dynamics of size distribution of Ag nanoparticles in solutions. The thermal-induced self-defocusing dominated in the case of high pulse repetition rate as well as in the case of nanosecond pulses. In the case of low pulse repetition rate, the self-focusing (γ = 3 × 10⁻¹³ cm² W⁻¹) and saturated absorption (β = −1.5 × 10⁻⁹ cm W⁻¹) of picosecond and femtosecond radiation were observed in these colloidal solutions. The nonlinear susceptibility of Ag nanoparticles ablated in water was measured to be 5 × 10⁻⁸ esu (at λ = 397.5 nm).     

The third-order optical nonlinearity of The pyrochlore phase 0.7Pb(Mg1/3Nb2/3)O3–0.3PbTiO3 thin film on quartz

The xPb(Mg_1/3Nb_2/3)O₃–(1−x)PbTiO₃ (PMNT) (with x=0.7) thin film is prepared on quartz substrates prepared using a sol–gel process. The PMNT thin film has a well-crystallized pyrochlore phase structure. The sign and magnitude of both real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ of the thin film have been determined by the Z-scan technique performed at 800 nm with a femtosecond laser. The nonlinear refraction index coefficient γ, the nonlinear absorption coefficient β of the thin film are 1.37×10⁻¹² cm²/W and −6.73×10⁻⁸ m/W, respectively. The real and imaginary part of the third-order nonlinear susceptibility of the film are 1.06×10⁻¹⁷ and −1.65×10⁻¹⁹ m²/V², respectively. The results suggested that the nonlinearity is dominated by the refractive for the film.     

Nonlinear refractive index measurements in antimony–sulfide glass films using a single beam nonlinear image technique

The nonlinear refractive index, n₂, of films based on the new glass system Sb₂O₃–Sb₂S₃ was measured at 1064 nm with laser pulses of 15 ps, using a single-beam nonlinear image technique in presence of a phase object. The films were prepared from bulk glasses by RF-sputtering. A large value of n₂ = 3 × 10⁻¹⁵ m²/W, which is three orders of magnitude larger than for CS₂, was determined. The result shows the strong potential of antimony–sulfide glass films for integrated nonlinear optics.     

Nonlinear optical and XPS properties of Au and Ag nanometer-size particle-doped alumina films prepared by the sol–gel method

Au and Ag nanometer-size particle-doped alumina films were prepared by the aqueous sol–gel method. Their XPS and third-order nonlinear optical properties were examined. The XPS results gave evidence of an interaction between Au and alumina. Third-order susceptibilities, χ⁽³⁾ and χ⁽³⁾/ obtained by degenerate four-wave mixing method were in the order of 10⁻⁸ esu and 10⁻¹⁰ esu.cm for doped films, respectively.     

Population lensing effect in Cr:LiSAF probed by Z-scan technique

An experiment has been performed for measuring a nonlinear refractive index that is due to the polarizability difference Δ_P between excited (⁴T₂) and ground (⁴A₂) states in a Cr³⁺:LiSAF crystal at λ = 647 nm. The latter one is responsible for a population lensing effect which has been monitored by using the eclipsing Z-scan technique. We have performed a data analysis that allows to distinguish between thermal and population contributions to the lensing effect. We have found Δ_P = 4.6 × 10⁻²⁵ cm³ which is in a good agreement with our previous measurements with a different technique.     

Domain wall pinning in polycrystalline perovskite La0.7Sr0.3MnO3

Reversible and irreversible domain wall (DW) motions have been investigated in La_0.7Sr_0.3MnO₃ ceramic samples using frequency-response complex permeability with various amplitudes of AC field. We also examine the effects of temperature in the range from 293 to 368 K and transverse DC magnetic field with a maximum of 4.40×10⁵ A/m on the real part of permeability (μ′). Two relaxations corresponding to reversible wall motions and domain rotations occur in low and high frequency regions, respectively. The irreversible DW displacements can be activated as the amplitude larger than the pinning field of 3 A/m, leading to an increase in μ′. The μ′ obeys a Rayleigh law at the temperature below 343 K or under DC field of less than 4.22×10⁴ A/m. The Rayleigh constant η increases from 5.45×10⁻² to 1.54×10⁻¹ (A/m)⁻¹ as the temperature rises from 293 to 343 K, and η decreases from 5.58×10⁻² to 3.67×10⁻² (A/m)⁻¹ with increasing DC field from 1.99×10³ to 4.22×10⁴ A/m.     

A new measurement of the weak magnetism term in the betaspectra of B and N

The betaspectra of ¹²B and ¹²N have been measured with a NaI crystal as spectrometer. Assuming a shape correction factor 1 + aW + bW² and b₋ = 1.106 × 10⁻⁴ MeV⁻², b₊ = −1.397 × 10⁻⁴ MeV⁻², the spectra yield a₋ = (+0.91 ± 0.11) × 10⁻² MeV⁻¹ and a₊ = (−0.07 ± 0.09) × 10⁻² MeV⁻. the a₋ − a₊ = (+0.98 ± 0.09) × 10⁻² MeV⁻¹ is in agreement with the weak magnetism prediction.     

Study of effects of Mn in CdS nanocrystals

Mn²⁺-doped CdS nanocrystals have been synthesized by adopting an aqueous solution precipitation method. These nanocrystals have been studied using X-ray diffraction (XRD), X-ray fluorescence (XRF), optical absorbance, photoluminescence (PL), DC electrical conductivity measurements and positron annihilation lifetime spectroscopy (PALS). The system has been found to be in the hexagonal phase. PL spectra have been studied on most prominent exciton peaks within the wavelength range (586–731 nm). The emission intensity is found to increase on increasing Mn²⁺ ion concentration (0–5%). Electrical conductivity lies within 0.819×10⁻⁶ to 1.69×10⁻⁶ Ω⁻¹ m⁻¹ and the system shows power law dependence for n=3–3.77. The Cd vacancies concentration has been found to decrease on increasing Mn%.     

Diffusion of W on A W(211) plane

The diffusion of W on a (211) plane of a W field emitter has been re-examined by means of the fluctuation autocorrelation method. Diffusion along channels yielded E = 16.8 ± 0.5 kcal, D₀ = (3 ± 1) × 10⁻⁵ cm² s⁻¹. For diffusion across channels E =6.6 kcal, D₀ = 4 × 10⁻⁹cm² s⁻¹ at T < 752 K, and E = 24 kcal, D₀ = 5 × 10⁻⁴ cm² s⁻¹ at T > 752 K. The results for diffusion along channels yield E and D₀ values intermediate between recent results by Wang and Ehrlich [Surf. Sci. 206 (1988) 451] using field ion microscopy (E = 19 kcal, D₀ = 7.7 × 10⁻³ cm² s⁻¹) and Tringides and Gomer [J. Chem. Phys. 84 (1986) 4049], using the same method as the present work but a larger slit (E = 13.3 kcal, D₀ = 7 × 10⁻⁷ cm² s⁻¹). The results for cross channel diffus good agreement with those of Tringides and Gomer below 752 K, where these authors stopped. The new high temperature results suggest that the channel wall exchange mechanism postulated by Tringides and Gomer for cross channel diffusion at low T gives way to diffusion by climbing over the channel walls with higher E but also higher D₀ above 752 K. Possible reasons for the discrepancies between these three sets of results and the absence of cross channel diffusion in the work of Wang and Ehrlich are briefly discussed.     

Optical nonlinearities and photo-excited carrier lifetime in CdS at 532 nm

Bound-electronic and free-carrier optical nonlinearities, and relaxation of photo-excited free carriers in CdS have been investigated by the use of a single-beam Z-scan technique at 532 nm. Under pulsed radiation of 35-ps duration with the input irradiances up to 4.8 GW/cm², the two-photon absorption coefficient, the bound-electron nonlinear refractive index, the free-carrier absorption cross-section, and the change in the refractive index per unit carrier density are determined to be 5.4±0.8 cm/GW, −(5.3±0.8)×10⁻¹³ cm²/W, (3.0±0.5)×10⁻¹⁷ cm² and −(0.8±0.1)×10⁻²¹ cm³, respectively. By using these values in the open-aperture Z-scans conducted with 7-ns laser pulses, the carrier recombination time is extracted to be 3.6±0.7 ns. The measured parameters are compared to theoretical calculations.     

Optical constants of Tl4Ga3InSe8 layered single crystals

The optical properties of Tl₄Ga₃InSe₈ layered single crystals have been studied by means of transmission and reflection measurements in the wavelength range of 500–1100 nm. The analysis of the room temperature absorption data revealed the presence of both optical indirect and direct transitions with band gap energies of 1.94 and 2.20 eV, respectively. Transmission measurements carried out in the temperature range of 10–300 K revealed that the rate of change of the indirect band gap with temperature is γ=−4.1×10⁻⁴ eV/K. The absolute zero value of the band gap energy was obtained as E_gi(0)=2.03 eV. The dispersion of the refractive index is discussed in terms of the Wemple–DiDomenico single-effective-oscillator model. The refractive index dispersion parameters: oscillator energy, dispersion energy, oscillator strength and zero-frequency refractive index were found to be 4.10 eV, 23.17 eV, 6.21×10¹³ m⁻² and 2.58, respectively. From X-ray powder diffraction study, the parameters of monoclinic unit cell were determined.     

Annealing effects on zirconium nitride films

ZrN films were deposited by dc reactive magnetron sputtering on silicon substrates under optimized nitrogen partial pressure of 6×10⁻⁵ mbar. Structural, electrical and optical properties were systematically investigated. Films deposited at room temperature exhibited Schottky structure without any silicide interfacial layer. These films have electrical resistivity of 4.23×10⁻³ Ω cm, which were crystalline in nature, with cubic (1 1 1) orientation. Refractive index and extinction coefficient were found to be 1.95 and 0.43, respectively at a wavelength of 350 nm.

Samples were annealed for 1 h in air at two temperatures, 350 and 550 °C. Scanning electron microscopy (SEM) and energy dispersive analysis of X-rays (EDAX) showed alloy penetration pits. Extent of penetration was greater in the films, which were annealed at higher temperature (550 °C). Variation in refractive index was observed in the range of 1.95–1.80 at 350 nm, for the annealed films, with increase in grain size from 7.25 to 11.10 nm. Poly-crystalline nature has been observed with (1 1 1) and (2 0 1) orientations. Resistivity is found to increase from 4.23×10⁻³ to 6.21×10⁻³ Ω cm.     

Crystal growth and characterisation of new organic nonlinear optical materials: 6-cyano and 6-nitro-2,2-dimethyl-3,4-epoxychroman

Two chiral organic nonlinear optical materials, (3S,4S)-(−)-6-cyano-2,2-dimethyl-3,4-epoxychroman (1) and (3R,4R)-(+)-6-nitro-2,2-dimethyl-3,4-epoxychroman (2), have been grown into single crystals of cm³-size. Although both compounds crystallise in the orthorhombic P2₁2₁2₁ space group, they are not isomorphous and their crystal packings are quite different. Angle tuned type II phase-matched second harmonic generation between 0.8 and 1.064 μm has been evidenced, with effective nonlinear coefficients d_eff of 1 and 5 pm/V at 0.96 μm for 1 and 2, respectively. These values are in agreement with those estimated in the oriented gas model approximation using EFISH first order hyperpolarisability values (β₀=2.6 and 4.0×10⁻³⁰ esu for 1 and 2, respectively).     

Duree de vie et depolarisation par collisions avec l''helium des niveaux 5P3/2 Et 5P1/2 de l''ion Cd

The lifetimes of the Cd⁺ 5²P_3/2 and 5²P_1/2 states have been measured by the Hanle effect. The Cd⁺ ions are produced in a d.c. discharge in cadmium vapor, with helium as buffer gas. The results are: τ(5²P_3/2) = (2.60±0.20) ×10⁻⁹sec, and τ(5²P_1/2) = (3.05 ± 0.13) × 10⁻⁹sec.

We measured also the cross sections for the destruction of the orientation in the 5²P_1/2Cd⁺ state (<5Ų), of the orientation (18±10Ų) and of the alignment (46±10Ų) in the 5²P_3/2 state due to collisions with the helium atoms.     

Methane mobility in carbon nanotubes

Quasi-elastic neutron scattering has been used to characterize the diffusivity of CH₄ molecules condensed in single-wall carbon nanotubes. It is shown that the two sites of adsorption, previously observed by adsorption volumetry and calorimetry measurements, correspond to a solid-like phase for the more strongly bound site at T<120 K and to a liquid-like component for the more weakly bound site at 70<T<120 K. The diffusion coefficients of the mobile molecules range between 3×10⁻⁷ to 15×10⁻⁷ cm² s⁻¹. The fraction of this viscous liquid diminishes as the temperature is decreased; the adsorbate is fully solidified at 50 K and below.     

Study on the structure dependent ultrafast third-order optical nonlinearity of GeS2–In2S3 chalcogenide glasses

The results of the femtosecond time-resolved optical Kerr at 820 nm in GeS₂–In₂S₃ chalcogenide glasses indicate that the response time in GeS₂–In₂S₃ glasses is subpicosecond, which is predominantly due to the distortion of the electron cloud. The value of χ⁽³⁾ in 0.95GeS₂–0.05In₂S₃ glass is also as large as 2.7 × 10⁻¹³ esu, and it reduces with the addition of In₂S₃, which may be ascribed to the microstructure evolution of GeS₂–In₂S₃ glasses. It is deduced that the intrinsic [Ge(In)S₄] tetrahedral structure units that possess the high hyperpolarizability may do great contribution to the enhancement of third-order optical nonlinearity while [S₃Ge–GeS₃] ethane-like molecular units make no considerable contribution to that in femtosecond time scale. These GeS₂–In₂S₃ and GeS₂–In₂S₃-based chalcogenide glasses would be expected to be the promising materials for all-optical switching devices.     

Corrosion monitoring of stainless steel 304L in lithium bromide aqueous solution using transmittance optical detection technique

We report a method based on the power ratio of transmittance for monitoring the corrosion rate in stainless steel 304L immersed in an aqueous solution of lithium bromide at 50 wt%, at 70 °C. The optical transmittance measured in the solution contaminated with corrosion oxides at different times of exposure is related to the physical degradation of the stainless steel samples. Lasers at 532 and 632 nm were utilized for monitoring the accumulation of corrosion oxides dissolved in the lithium bromide solution of the metallic samples for 480 h. The change in the optical power of transmittance was 13 μW/480 h measured at 532 nm and 3.6 μW/480 h at 632 nm. The variation of the power ratio for 532 nm was from 0.01 to 0.24, and for 632 nm, from 0.01×10⁻³ to 15.61×10⁻³; this is proportional to an accumulated corrosion rate of [0.0142×10⁻³–0.552×10⁻³ g/cm²] for an exposure time of 432 h.     

Optical second-harmonic investigations of the isothermal desorption of SiO from the Si(100) and Si(111) surfaces

The isothermal desorption of SiO from the Si(100) and Si(111) surfaces was investigated by means of optical second-harmonic generation (SHG). Due to the high adsorbate sensitivity of this method, desorption rates could be measured over a wide range from 10⁻¹ to 10⁻⁶ ML s⁻¹. From their temperature dependence between 780 and 1000 K, activation energies of E_A=3.4±0.2 eV and E_A=4.0±0.3 eV and pre-exponential factors of ν₀=10^16±1 s⁻¹ and ν₀=10^20±1 s⁻¹ for SiO desorption were obtained for Si(100) and Si(111), respectively. In the case of the Si(100) surface, a pronounced decrease of the first-order rate constants was observed upon increasing the initial coverage from 0.02 to 0.6 ML. The results are interpreted in terms of coverage-dependent oxygen-binding configurations, which influence the stability of the oxide layer.