氮气退火对二氧化钛薄膜光学性能的影响

 提出了一种利用离子注入和后续退火制备氮掺杂TiO₂薄膜的方法。首先在室温下向石英玻璃中注入Ti离子,随后在氮气中退火到900 ℃,从而制备了氮掺杂的玻璃基TiO₂薄膜。SRIM2006程序模拟和卢瑟福背散射谱（RBS）研究表明注入离子从样品表面开始呈高斯分布,实验结果和模拟结果吻合很好。X射线光电子能谱（XPS）研究结果表明注入态样品中形成了金属Ti和TiO₂,900 ℃退火后金属Ti转变成TiO₂,同时N原子替代少量的晶格O原子形成了O－Ti－N化合物。紫外-可见吸收光谱（UV-Vis）结果显示,当退火温度至500 ℃时,在吸收光谱中开始出现TiO₂的吸收边,随退火温度升高到900 ℃,由于O－Ti－N化合物形成,TiO₂的吸收边从3.98 eV红移到3.30 eV,TiO₂吸收边末端延伸到可见光区,在可见光区的吸收强度明显增加。     

退火温度对Cr掺杂ZnO薄膜的微结构与机械性能的影响研究

本研究利用射频磁控溅镀法在玻璃基板上制备3 at.%的Cr掺杂ZnO薄膜,再以300℃～500℃温度退火处理25 mins,并探讨了退火温度对Al掺杂ZnO薄膜的微观结构与机械性能的影响.微观结构分析结果表明Cr掺杂ZnO薄膜的结晶方向为(002),且沿(002)方向的成长随退火温度升高而越加明显,但薄膜的表面却随退火温度升高而变得越来越粗糙.机械性能分析结果揭示晶粒尺寸随退火温度升高而增大,导致差排原子的动能随之降低,致使Cr掺杂ZnO薄膜的硬度随退火温度升高而增大,但对其对杨氏模量却没有太大的影响;此外,Cr掺杂ZnO薄膜的耐磨性与韧性均随退火温度升高而增强,表明退火处理对该薄膜的抗塑性形变能力有很大帮助.     

Zn掺杂β-Ga2O3薄膜的制备和特性研究

β-Ga₂O₃是一种宽带隙半导体材料,能带宽度E_g≈5.0eV,在光学和光电子学领域有广泛的应用。用射频磁控溅射方法在Si衬底和远紫外光学石英玻璃衬底制备了本征β-Ga₂O₃薄膜及Zn掺杂β-Ga₂O₃薄膜,用紫外 可见分光光度计、X射线衍射仪、荧光分光光度计对本征β-Ga₂O₃薄膜及Zn掺杂β-Ga₂O₃薄膜的光学透过、光学吸收、结构和光致发光进行了测量,研究了Zn掺杂和热退火对薄膜结构和光学性质的影响。退火后的β-Ga₂O₃薄膜为多晶结构,与本征β-Ga₂O₃薄膜相比,Zn掺杂β-Ga₂O₃薄膜的β-Ga₂O₃(111)衍射峰强度变小,结晶性变差,衍射峰位从35.69°减小至35.66°。退火后的Zn掺杂β-Ga₂O₃薄膜的光学带隙变窄,光学透过降低,光学吸收增强,出现了近边吸收,薄膜的紫外、蓝光及绿光发射增强。表明退火后Zn掺杂β-Ga₂O₃薄膜中的Zn原子被激活充当受主。     

退火温度对Cr掺杂ZnO薄膜的微结构与机械性能的影响研究

本研究利用射频磁控溅镀法在玻璃基板上制备3 at.%的Cr掺杂ZnO薄膜,再以300℃～500℃温度退火处理25 mins,并探讨了退火温度对Al掺杂ZnO薄膜的微观结构与机械性能的影响.微观结构分析结果表明Cr掺杂ZnO薄膜的结晶方向为(002),且沿(002)方向的成长随退火温度升高而越加明显,但薄膜的表面却随退火温度升高而变得越来越粗糙.机械性能分析结果揭示晶粒尺寸随退火温度升高而增大,导致差排原子的动能随之降低,致使Cr掺杂ZnO薄膜的硬度随退火温度升高而增大,但对其对杨氏模量却没有太大的影响;此外,Cr掺杂ZnO薄膜的耐磨性与韧性均随退火温度升高而增强,表明退火处理对该薄膜的抗塑性形变能力有很大帮助.     

退火温度对Cr掺杂ZnO薄膜的微结构与机械性能的影响研究

本研究利用射频磁控溅镀法在玻璃基板上制备3 at.%的Cr掺杂ZnO薄膜,再以300℃～500℃温度退火处理25 mins,并探讨了退火温度对Al掺杂ZnO薄膜的微观结构与机械性能的影响.微观结构分析结果表明Cr掺杂ZnO薄膜的结晶方向为(002),且沿(002)方向的成长随退火温度升高而越加明显,但薄膜的表面却随退火温度升高而变得越来越粗糙.机械性能分析结果揭示晶粒尺寸随退火温度升高而增大,导致差排原子的动能随之降低,致使Cr掺杂ZnO薄膜的硬度随退火温度升高而增大,但对其对杨氏模量却没有太大的影响;此外,Cr掺杂ZnO薄膜的耐磨性与韧性均随退火温度升高而增强,表明退火处理对该薄膜的抗塑性形变能力有很大帮助.     

退火对电子束热蒸发Al2O3薄膜性能影响的实验研究

 用电子束热蒸发方法镀制了Al₂O₃材料的单层膜，对它们在空气中进行了250~400 ℃的高温退火。对样品的透射率光谱曲线进行了测量，计算了样品的消光系数、折射率和截止波长。通过X射线衍射仪（XRD）测量分析了薄膜的微观结构,采用表面轮廓仪测量了样品的表面均方根粗糙度。结果发现随着退火温度的提高光学损耗下降，薄膜结构在退火温度为400 ℃时仍然为无定形态，样品的表面粗糙度随退火温度的升高而增加。引起光学损耗下降起主导作用的是吸收而不是散射，吸收损耗的下降主要是由于退火使材料吸收空气中的氧而进一步氧化，从而使薄膜材料的非化学计量比趋于正常。     

射频磁控反应溅射制备的Ag2O薄膜的椭圆偏振光谱研究

Ag₂O薄膜在新型超高存储密度光盘和磁光盘方面具有潜在的应用前景.利用射频磁控反应溅射技术, 通过调节衬底温度在沉积气压为0.2 Pa、氧氩比为2:3的条件下制备了一系列Ag₂O 薄膜.利用通用振子模型(包括1个Tauc-Lorentz振子和2个Lorentz 振子)拟合了薄膜的椭圆偏振光谱.在1.5-3.5 eV能量区间,薄膜的折射率在2.2-2.7之间, 消光系数在0.3-0.9之间. 在3.5-4.5 eV能量区间,薄膜呈现了明显的反常色散,揭示Ag₂O薄膜的等离子体振荡频率在 3.5-4.5 eV之间. 随着衬底温度的升高,薄膜的光学吸收边总体上发生了红移, 该红移归结于薄膜晶格微观应变随衬底温度的升高而增大. Ag₂O薄膜的光学常数表现出典型的介质材料特性.     

退火对B掺杂纳米金刚石薄膜微结构和电化学性能的影响

采用热丝化学气相沉积法制备B掺杂纳米金刚石薄膜,并对薄膜进行真空退火处理,系统研究了不同退火温度对B掺杂纳米金刚石薄膜的微结构和电化学性能的影响.结果表明,当退火温度升高到800 ℃后,薄膜的Raman谱图中由未退火时在1157,1346,1470,1555 cm^-1处的4个峰转变为只有D峰和G峰,说明晶界上的氢大量解吸附量减少,并且D峰和G峰的积分强度比I_D/I_G值变为最小,即sp²相团簇     

退火及超声处理对ZnO薄膜结构和发光特性的影响

 利用对向靶射频磁控溅射系统在Si（100）衬底上制备了ZnO薄膜，并对其进行了退火和超声处理。采用XRD,AFM和光致发光谱对其结构、表面形貌和性能进行了分析。结果表明：沉积态ZnO薄膜（002）择优取向稍差,尺寸较小,表面粗糙度较大。随退火温度的升高，颗粒粒径增大，样品的取向性和结晶度都明显变好，应力状态由压应力转变为张应力,粗糙度降低。超声处理缓解了薄膜中的张应力，晶粒尺寸更趋增大;用波长为280 nm的激发光激发薄膜时，沉积态薄膜无发光峰存在;随着退火温度升高，出现了一个378 nm的紫外峰和一个398 nm的紫峰;紫外峰峰值强度随退火温度升高不断增强，而紫峰的峰位随退火温度升高基本不发生变化，峰值强度增强;700 ℃退火后的薄膜经超声处理后，发光谱中出现了峰值波长为519 nm的绿色发光带。     

Zn离子注入和退火对ZnO薄膜光学性能的影响

 利用溶胶凝胶方法在石英玻璃衬底上制备了ZnO薄膜，将能量56 keV、剂量1×10¹⁷ cm^-2的Zn离子注入到薄膜中。离子注入后，薄膜在500~900 ℃的氩气中退火，利用X射线衍射谱、光致发光谱和光吸收谱研究了离子注入和退火对ZnO薄膜结构和光学性质的影响。结果显示：衍射峰在约700 ℃退火后得到恢复；当退火温度小于600 ℃时，吸收边随着退火温度的提高发生蓝移，超过600 ℃时，吸收边随着退火温度的提高发生红移；近带边激子发光和深能级缺陷发光都随退火温度的提高而增强。     

The effects of post-thermal annealing on the optical parameters of indium-doped ZnO thin films

Indium-doped ZnO thin films are deposited on quartz glass slides by RF magnetron sputtering at ambient temper- ature. The as-deposited films are annealed at different temperatures from 400 C to 800 C in air for 1 h. Transmittance spectra are used to determine the optical parameters and the thicknesses of the films before and after annealing using a nonlinear programming method, and the effects of the annealing temperatures on the optical parameters and the thickness are investigated. The optical band gap is determined from the absorption coefficient. The calculated results show that the film thickness and optical parameters both increase first and then decrease with increasing annealing temperature from 400 C to 800 C. The band gap of the as-deposited ZnO:In thin film is 3.28 eV, and it decreases to 3.17 eV after annealing at 400 C. Then the band gap increases from 3.17 eV to 3.23 eV with increasing annealing temperature from 400 C to 800 C.     

退火对多晶ZnO薄膜结构与发光特性的影响

用射频反应溅射法在Si（111）衬底上制备了C轴取向的多晶ZnO薄膜，通过不同温度的退火处理，研究了退火对多晶ZnO薄膜结构和发光特性的影响.由x射线衍射得知，随退火温度的升高，晶粒逐渐变大，薄膜中压应力由大变小至出现张应力.光致发光测量发现，样品在430nm附近有一光致发光峰, 峰的强度随退火温度升高而减弱，联合样品电阻率随退火温度升高而逐渐变大的测量及能级图，推测出ZnO薄膜中的蓝光发射主要来源于锌填隙原子缺陷能级与价带顶能级间的跃迁. 关键词： ZnO薄膜 退火 光致发光 射频反应溅射     

Room temperature transparent conducting oxides based on zinc oxide thin films

Doped zinc oxide thin films are grown on glass substrate at room temperature under oxygen atmosphere, using pulsed laser deposition (PLD). O₂ pressure below 1 Pa leads to conductive films. A careful characterization of the film stoichiometry and microstructure using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) concludes on a decrease in crystallinity with Al and Ga additions (≤3%). The progressive loss of the (0 0 2) orientation is associated with a variation of the c parameter value as a function of the film thickness and substrate nature. ZnO:Al and ZnO:Ga thin films show a high optical transmittance (>80%) with an increase in band gap from 3.27 eV (pure ZnO) to 3.88 eV and 3.61 eV for Al and Ga doping, respectively. Optical carrier concentration, optical mobility and optical resistivity are deduced from simulation of the optical data.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Enhancement in NBE emission and optical band gap by Al doping in nanocrystalline ZnO thin films

Transparent Al doped ZnO nanocrystalline films with a crystallite size less than 19 nm are obtained by spray pyrolysis. Band gap increases monotonically from 3.16 to 3.31 eV with increasing aluminum dopant up to 1.56 at.% facilitating increasing width of a transmission window in addition to the band gap tuning of 4.74% which compares favorably well with literature. UV emission with continuously increasing intensity is obtained which reflects on the good crystalline quality of the films. Also the defect emissions are suppressed remarkably as the dopant Al concentration increases in ZnO. The band gap tuning by quite small increment in dopant amount makes the present films, much attractive for the fabrication of light emitting devices with a much sought-for benefit of large area fabrication. FESEM shows the surface is granular with grain size lying in the range of 20–35 nm and EDX confirms the presence of Al in the doped samples     

退火对ZnO:Al薄膜光致发光性能的影响

 采用溶胶-凝胶工艺在石英衬底上制备ZnO:Al（AZO）薄膜，通过不同温度的退火处理，研究了退火对AZO薄膜结构和光致发光特性的影响。XRD图谱表明：所制备的薄膜具有c轴高度择优取向，随着退火温度的升高，(002)峰的强度逐渐增强，同时(002)峰的半高宽逐渐减小,表明晶粒在不断增大。未退火样品的光致发光（PL）谱由361 nm附近的紫外带边发射峰和500 nm附近的深能级发射峰组成。样品经退火后，以500 nm为中心的绿带发射逐渐减弱，而带边发射强度有所增强,并且逐渐红移到366 nm附近，与吸收边移动的测试结果相吻合。对经过不同时间退火的样品分析表明，AZO薄膜的发光特性与退火时间也有很大关系，时间过短可见波段的发射较强，但时间过长会使晶粒发生团聚，导致紫外发射峰强度减弱。     

Structural,electrical and optical studies on spray-deposited aluminium-doped ZnO thin films

Thin films of zinc oxide (ZnO) were deposited on cleaned glass substrates by chemical spray pyrolysis technique using Zn(CH₃COO)₂ as precursor solution. Also, aluminium-doped thin films of ZnO were prepared by using AlCl₃ as doping solution for aluminium. The dopant concentration [Al/Zn atomic percentage (at%)] was varied from 0 to 1.5 at% in thin films of ZnO prepared in different depositions. Structural characterization of the deposited films was performed with X-ray diffraction (XRD) studies. It confirmed that all the films were of zinc oxide having polycrystalline nature and possessing typical hexagonal wurtzite structure with crystallite size varying between 100.7 and 268.6 nm. The films exhibited changes in relative intensities and crystallite size with changes in the doping concentration of Al. The electrical studies established that 1 at% of Al-doping was the optimum for enhancing electrical conduction in ZnO thin films and beyond that the distortion caused in the lattice lowered the conductivity. The films also exhibited distinct changes in their optical properties at different doping concentrations, including a blue shift and slight widening of bandgap with increasing Al dopant concentration.     

退火温度对Cu:ZnO薄膜绿光发射的影响

利用溶胶-凝胶法在Si衬底上制备了不同退火温度的Cu:ZnO薄膜.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜和光致发光谱研究了样品的晶格结构、表面形貌、成分及其发光特性.结果表明:所有样品均具有高度的c轴择优取向,随着退火温度的升高,样品的结晶质量变好,样品的表面都被晶粒覆盖,强而稳定的绿光发射被观察到.绿光强度随退火温度的升高先增加后减小,发光中心位置不随退火温度的变化而改变,这样的绿光发射强而稳定.XRD和XPS结果表明,随退火温度的升高Cu2+还原为Cu+,导致Cu:ZnO薄膜形成的缺陷是VZn,所以绿光发射是由VZn引起的.Cu2+还原为Cu+时,Cu:ZnO薄膜中VZn浓度增加,使绿光发射强度增大.当退火温度超过800?C时,Cu2+的还原能力变差,绿光发射强度减弱.     

Metalorganic chemical vapor deposition of ZnO:N using NO as dopant

Highly c-axis orientated ZnO was grown by metal organic chemical vapor deposition (MOCVD) using NO as both oxidant and nitrogen dopant source. The properties of the deposited material are investigated by X-ray diffraction to study the crystalline quality of the thin films. Photoluminescence measurements are used to determine the optical properties of the material as a function of VI/II ratio and post growth-annealing temperature. Two transitions appear at 3.228 and 3.156 eV and are interpreted as involving active nitrogen acceptors. An increase in the NO flow increases the concentration of nitrogen in the films, which are activated by subsequent annealing at 600 °C in an oxygen ambient.     

Structural, optical and electrical properties of ZnO:Al thin films for optoelectronic applications

Undoped and aluminum-doped ZnO thin films are prepared by the sol–gel spin-coating process. Zinc acetate dihydrate, ethanol and mono-ethanolamine are used as precursor, solvent and stabilizer, respectively. The atomic percentage of dopant in solution were [Al/Zn] = 1 %, 2 % and 3 %. The effect of Al doping on the optical and electrical properties of ZnO films was investigated by X-ray diffraction (XRD), Four-Point probe technique and UV–visible spectrophotometery. The results from the X-ray diffraction show that the pure ZnO thin films had a polycrystalline structure of the hexagonal Wurtzite Type. A minimum resistivity of $3.3 \times 10^{-3} \Omega \cdot \mathrm{cm}$ was obtained for the film doped with 2 mol % Al. Optical transmissions reveal a good transmittance within the visible wavelength spectrum region for all of the films. The value of the band gap is enhanced from 3.21 eV (undoped ZnO) to 3.273 eV (Al/Zn = 3 %), the increase in the band gap can be explained by the Burstein–Moss effect.