衬底温度对氧化锌薄膜电学性质的影响

氧化锌是一种性能良好的半导体材料,可以用作薄膜场发射阴极中的电子传输层材料,主要研究了用磁控溅射方法在不同衬底温度下生长ZnO薄膜的电学特性,分析了ZnO薄膜的电阻率和击穿场强随温度的变化关系。     

表面预处理对氧化锌薄膜质量的影响

用MOCVD方法在c面蓝宝石衬底上生长ZnO薄膜。生长前衬底表面进行预处理,观察不同表面预处理对ZnO薄膜质量的影响。测量氧化锌的XRD谱,观察表面预处理后对氧化锌薄膜结晶质量的影响。室温下用325nm的He-cd激光器作为激发源测量ZnO薄膜的紫外发光谱,观察表面处理后对ZnO薄膜发光特性的影响。用HL5500 Hall System分别对ZnO薄膜的电学特性进行了测试。得到了ZnO薄膜的电阻率和霍尔迁移率,并得到氧气气氛处理后电阻率变小,霍尔迁移率变大;氮气气氛射频处理后电阻率变大,霍尔迁移率变小的结果。     

溅射方法生长的氧化锌薄膜的阴极射线和光致发光特性

近紫外光发射氧化锌薄膜是一种新兴的发光材料,它的发光波长比氮化镓的蓝光波长更短,在光存储应用中可以进一步提高光存储的密度,因而在光电子领域具有重要应用价值而备受关注。在此介绍我们用直流反应溅射方法在硅衬底上生长的氧化锌薄膜,观察了它们的阴极射线发光和光致发光光谱,研究了发光与薄膜晶体结构,以及发光与激发电子束流的关系等。并从中推测出ZnO薄膜中的发光中心。     

磁控溅射方法生长的氮氧锌薄膜的光学特性

氧化锌(ZnO)是一种具有六方结构的宽禁带Ⅱ--Ⅵ族半导体材料，室温下能带带隙Eg为3.37eV。由于氧化锌在室温条件下具有较高的激子束缚能(60meV)，保证了其在室温下较强的激子发光。此外氧化锌还具有较高的热稳定性和抗化学腐蚀特性，因而被认为是制作紫外半导体激光器的合适材料。自1997年首次发现ZnO室温紫外受激发射以来，ZnO已成为继GaN之后紫外发射材料的又一研究热点。但是，目前对于p型氧化锌及其发光器件的研究仍处于探索阶段，对其光电特性的研究仍需要更多投入。本文利用磁控溅射方法制备出氮氧锌薄膜样品，并通过在氧气气氛下退火处理，改变薄膜样品中氮的含量。通过X射线衍射谱、X射线光电子能谱、光致发光谱及喇曼光谱的测试，研究了氮在氧化锌薄膜中的含量变化以及氮对氧化锌薄膜的结构和光学特性的影响。     

在a-平面蓝宝石衬底上分子束外延生长的ZnO和ZnMgO材料结构和光学性质(英文)

氧化锌材料是新一代宽禁带光电子半导体材料,我们通过等离子体分子束外延设备,在a plane的蓝宝石衬底生长了高质量的氧化锌外延材料。在生长过程中用反射高能电子束衍射仪(RHEED),在位地研究了生长时材料薄膜的表面形貌。通过调节ZnMgO材料镁的组份,生长了禁带宽度可调的宽禁带材料。用紫外-可见透射光谱研究了ZnO,Zn0.89Mg0.11O和Zn0.80Mg0.20O薄膜材料的透射和吸收光谱性质,观察到Zn0.89Mg0.11O,Zn0.80Mg0.20O材料的吸收边的蓝移现象等。以上说明了我们用分子束外延生长 收稿日期:2003 07 22·09·　　第1期StructuralandOpticalCharacterizationofZnOandZnMgOFilmsona-planesapphiresbyMolecularBeamEpitaxy2004年设备成功的生长了高质量的氧化锌和组份渐变的ZnMgO薄膜材料。     

氧化锌薄膜光电功能材料研究的关键问题

氧化锌薄膜光电功能材料是近年来新发展起来的研究课题,由于它在短波长光电信息功能材料方面具有潜在的应用前景而备受关注.为了开发ZnO结型光电器件,目前首先需要解决高质量ZnO单晶薄膜的外延及p型掺杂等关键问题.综合国内外的研究结果,结合我们的工作,叙述了利用多晶格匹配原理通过过渡层在Si衬底上异质外延高质量ZnO薄膜,介绍了用SiC作过渡层生长ZnO薄膜的有关问题.对ZnO的p型掺杂,分析了制备p型ZnO的困难和利用Ⅲ-Ⅴ族共掺杂方法生长p型ZnO的作用和优点.     

MOCVD法生长SAWF用ZnO/Diamond/Si多层结构

使用等离子体辅助MOCVD系统在金刚石,硅衬底上成功地制备了氧化锌多层薄膜材料,通过两步生长法对薄膜质量进行了优化。XRD测试显示优化后的样品具有c轴的择优取向生长,PL谱测试表明样品经优化后不仅深能级发射峰消失,同时紫外发射峰增强。对优化后的样品的表面测试显示出较低的表面粗糙度。比较氧化锌多层薄膜结构的声表面波频散曲线,ZnO薄膜声表面滤波器受膜厚和衬底材料的影响较大。当ZnO薄膜较薄时,在它上面的传播速度将与衬底上的传播速度接近,与其他衬底上生长的薄膜相比,以金刚石这种快声速材料为衬底的ZnO多层薄膜结构,声表面波滤波器的中心频率将提高1倍左右。     

ZnO薄膜的反射、透射光谱及能带结构测量

采用正入射的方法研究了生长在硅基片上的氧化锌薄膜的反射光谱，测量出氧化锌薄膜的光学吸收边在370nm，所对应的能量值为3.35eV，测量生长在石英玻璃基片上的氧化锌薄膜的透射光谱，得到相同的吸收边，表明ZnO薄膜的光学禁带宽度与体材料的禁带宽度一致，反射谱中，在550－600nm之间观察到一个吸收峰，吸收峰的位置以及吸收边的陡峭程度都薄膜的结晶状况的不同而有所不同。     

低温缓冲层对氧化锌薄膜质量的影响

利用金属有机化学气相沉积(MOCVD)法,在Si衬底上外延生长ZnO薄膜。为了改善氧化锌薄膜的质量,首先在Si衬底上生长低温ZnO缓冲层,然后再生长高质量的ZnO薄膜。通过XRD、SEM、光致发光(PL)光谱的实验研究,发现低温ZnO缓冲层可有效降低ZnO薄膜和Si衬底之间的晶格失配以及因热膨胀系数不同引起的晶格畸变。利用低温缓冲层生长的ZnO薄膜的(002)面衍射峰的强度要比直接在Si上生长的ZnO薄膜样品的高,并且衍射峰的半高宽也由0.21°减小到0.18°,同时有低温缓冲层的样品室温下的光致发光峰也有了明显的增高。这说明利用低温缓冲层生长的ZnO薄膜的结晶质量和光学性质都得到了明显改善。     

ZnO薄膜的椭偏和DLTS特性

用射频磁控溅射在硅衬底上淀积氧化锌薄膜,并对样品分别作氮气、空气、氧气等不同条件下退火处理。为研究退火气氛对ZnO/Si薄膜中缺陷以及折射率的影响,由深能级瞬态谱(DLTS)以及椭偏测量方法进行了检测。椭偏测量结果表明相对原始生长的样品,在氮气和空气退火使ZnO薄膜折射率下降,但氧气中退火使折射率升高。我们对折射率的这种变化机理进行了解释。DLTS测量得到一个与Zni**相关的深能级中心E1存在,氧气气氛退火可以消除E1能级。在氮气退火情况下Zn*i*的存在对抑制VO引起的薄膜折射率下降有利。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.