激光二极管自混合干涉实验仪和微振动研究

用振动激励信号做频率电压变换的倒相触发信号,可以从激光二极管自混合干涉信号还原扬声器谐振时的振动波形,输出信号的振幅与扬声器的振幅成正比. 用正弦波、方波和三角波信号分别激励扬声器,利用自制的激光二极管自混合干涉实验仪观测了的扬声器振动特性,测量了扬声器的谐振曲线.     

分数阶双稳系统中的非周期振动共振

在受二进制非周期信号和周期方波信号激励的分数阶双稳系统中,研究了非周期振动共振问题,用于微弱非周期信号的检测和增强.当非周期信号脉宽较大时,系统为小参数,通过调节周期方波信号的幅值,能够实现非周期振动共振.当非周期信号脉宽较小时,分别通过变尺度法和二次采样法实现了非周期振动共振.使用变尺度法,得到的大参数等价系统能够匹配任意小的非周期信号脉宽,其中变尺度系数是该方法在使用过程中需要选择的关键参数.使用二次采样法,二次采样后得到的非周期信号具有较大的脉宽,能够匹配原先的小参数系统,其中二次采样频率比是该方法使用过程中的关键参数.这两种方法虽然实现非周期振动共振的物理过程不同,但能够达到相同的效果.系统阶数对振动共振产生影响,随着阶数的增大,发生最佳振动共振时所需要的辅助信号幅值变大,同时系统输出的最佳时间序列与输入非周期信号之间的相似性增强.     

基于压缩感知的振动数据修复方法

为解决旋转机械振动信号丢失数据修复的问题,提出一种基于压缩感知原理的振动数据修复方法.首先对采集到的不完整信号进行处理,将无信息输入时刻对应的数据用零元素填充得到有损信号,以单位矩阵为基础,根据有损信号中零元素的位置信息,构造对应于压缩感知框架下的观测矩阵;再根据待修复信号的特点并结合先验知识,构造或选择能够对振动信号进行稀疏表示的字典矩阵;然后使用高效且稳定的追踪算法,根据有损信号、观测矩阵以及字典矩阵重构原始信号,实现丢失振动数据的修复.使用仿真数据检验方法的有效性;使用实测的轴承振动状态数据验证方法对于振动数据的适用性,并通过比较完整信号、有损信号和修复信号对应的时域和频域特征值来检验数据修复效果.实验结果表明:本文方法能够有效地实现丢失数据的修复,且从统计特征的角度来看,相比于有损信号,修复信号能够更为准确地描述真实完整的振动信号.     

分时复用光纤光栅振动传感器阵列

结合基于3×3耦合器的光纤Mach-Zehnder干涉仪和可调谐光纤Fabry-Perot滤波器（Fiber-Fabry-Perot,FFP）,提出了一种分时复用光纤光栅振动传感器的技术.用FFP对串联在一根光纤上的光纤光栅的波长进行轮流扫描,让光栅的反射光按波长顺序依次通过FFP.而对于每一光纤光栅上外加的振动信号,用光纤Mach-Zehnder干涉仪进行测量.实际测量结果显示,FFP结合Mach-Zehnder能够对每一只光栅上的振动信号进行分时测量.     

空气加热器振动信号的测量与处理研究

针对火箭发动机试验中某加热器振动信号的测量和处理问题,首先在加热器某测点上冗余配置了两种不同型号的加速度计,完成了其振动加速度信号的测量;之后,基于MATLAB编程方法实现了加热器振动加速度信号消除趋势项和平滑预处理,通过对两种预处理结果的比较分析,得到了最终合理的振动加速度信号;最后,将振动加速度信号进行了频域二次积分解析运算,得到了其振动位移量信号;试验结果验证了信号测量的可靠性和处理结果的有效性和准确性,从而为加热器振动状况的分析提供了全面、可靠、准确的数据依据。     

基于多重分形谱的光纤周界振动信号识别

为了有效识别光纤周界系统的振动信号,提出一种多重分形谱参数和改进概率神经网络相结合的光纤振动信号识别方法.该方法能够避免特征提取过程中需要选择经验阈值和模式识别过程中需要确定平滑因子的不足.首先,检验分析光纤振动信号多重分形的存在性和有效性.然后,计算和提取光纤振动信号的多重分形谱参数,构成能够准确描述信号非线性和复杂性特性的特征向量.最后,采用改进的概率神经网络算法进行自适应地学习和分类,实现对不同光纤振动信号的识别.采用现场实验采集的四种振动信号对该方法进行验证,结果表明,平均识别率达到96.25%,识别时间为1.63s.该方法在正确识别率方面优于传统的概率神经网络算法.     

利用蜂鸣片受迫振动测液体黏度

用信号发生器驱动蜂鸣片在真空泵油中产生受迫振动,通过测量液体中振动物体的谐振频率求得液体阻尼系数,进而确定了液体黏度.     

线性时滞反馈引起的周期性振动共振分析

研究了高频信号和微弱低频信号同时激励下线性时滞反馈对过阻尼双稳系统和Duffing振子系统中振动共振现象的影响. 解析分析和数值结果都表明, 系统对低频信号的响应幅值增益随时滞参数的变化同时呈现两种不同的周期性关系, 其周期分别为输入的高频信号和低频信号的周期. 数值结果还表明, 对不存在经典振动共振现象的单稳Duffing系统, 通过调节时滞参数也可以引发振动共振现象. 使用时滞反馈不仅可以有效地控制振动共振, 还可以进一步增强系统对微弱低频信号的响应. 关键词： 双稳系统 Duffing 系统 线性时滞反馈 振动共振     

基于悬臂梁调谐技术的光纤光栅无源振动监测

采用匹配光纤光栅设计了一种结构简单的振动信号无源监测装置.该装置利用悬臂梁调谐技术能够将微小振动信号转化为光电探测器可探测的光强信号,利用示波器实现实时监测.实验中对振幅为3mm的简谐振动信号进行了监测,测量结果与振动频率一致,可测量7～20Hz的振动,信噪比不低于14.9dB.监测频率受限是因为悬臂梁的性质,如采用金属材料或者采用齿轮组对转子进行减速,该装置可探测更高的频率.     

基于泛频振动的石英增强光声光谱测声器优化设计

为了进一步提高基于泛频振动的石英增强光声光谱测声器探测灵敏度,在一次泛频振动模式下采用一个比商用标准音叉外形尺寸大5倍的定制大音叉,并对其性能进行优化.通过理论和实验研究得出了音叉与激光的最佳作用位置,发现音叉的一次泛频振动有两个波腹点,且在距离音叉根部8 mm处,音叉振臂的振动幅度最大.微型声音谐振腔由三种不同内径的不锈钢毛细管加工而成,与音叉组成共轴配置石英增强光声光谱光谱测声器,用来进一步增强信号幅值.在最佳微型声音谐振腔配置下,获得了30倍的信号增益因子,有效提高了石英增强光声光谱光谱测声器的探测灵敏度.     

Evaluation of elastic modulus of cantilever beam by TA-ESPI

The paper proposes an evaluation technique for the elastic modulus of a cantilever beam by vibration analysis based on time average electronic speckle pattern interferometry (TA-ESPI) and Euler-Bernoulli equation. General approaches for the measurement of elastic modulus of a thin film are the Nano indentation test, Buldge test, Micro-tensile test, and so on. They each have strength and weakness in the preparation of the test specimen and the analysis of experimental results. ESPI is a type of laser speckle interferometry technique offering non-contact, high-resolution and whole-field measurement. The technique is a common measurement method for vibration mode visualization and surface displacement. Whole-field vibration mode shape (surface displacement distribution) at resonance frequency can be visualized by ESPI. And the maximum surface displacement distribution from ESPI can be used to find the resonance frequency for each vibration mode shape. And the elastic modules of a test material can be easily estimated from the measured resonance frequency and Euler-Bernoulli equation. The TA-ESPI vibration analysis technique can be used to find the elastic modulus of a material requiring simple preparation process and analysis.     

Determination of elastic modulus of a beam by using electronic speckle pattern interferometry

This paper proposes a sonic resonance test for an elastic modulus measurement which is based on the electronic speckle pattern interferometry. Previous measurement technique of elastic constant has the limitation of application for thin film or polymer material because contact to specimen affects the result. It has been developed as a non-contact optical measurement technique which can visualize resonance vibration mode shapes with whole field. The maximum vibration amplitude at each vibration mode shape is a clue to find the resonance frequencies. The dynamic elastic constant of test material can be easily determined from vibration of a beam equation using the measured resonance frequencies. The proposed technique is able to give high accurate elastic modulus of materials through a simple experimental set-up and analysis. The experimental result also compared to the theoretical result.     

Large amplitude point-vibration measurement with optical-fiber moiré-based technique

We describe a technique that is used for the real-time measurement of the vibration of an object point. The technique can be used when the vibration is characterized by a large amplitude, i.e. several millimeters. The technique has additional advantages that it requires no special surface treatment and is insensitive to object in-plane displacements that are small. In this technique an object point is illuminated by a small diameter beam (at an angle) that is structured with straight parallel fringes. The illuminated object point is then imaged onto a Ronchi ruling. The total light transmitted through the Ronchi ruling is then used to recover the vibration of the object point, in real time, by using well-known servo techniques.     

TIME-FREQUENCY ANALYSIS OF A SUSPENSION BRIDGE BASED ON GPS

This paper describes the results obtained from full-scale measurements of Humen bridge, which is the second longest suspension bridge in China. A real-time kinematic (RTK) global positioning system (GPS) has been developed and installed on the Humen bridge for on-line monitoring of bridge deck movements. The field wind-induced vibration data were measured by this monitoring system. Three system identification techniques are then adopted in the modal analysis of the wind-induced vibration response: the time-frequency Wigner distribution (WD) technique, the frequency-domain fast Fourier transform (FFT) technique and the time-domain auto-regressive moving average vector (ARMAV) technique. The WD technique can recognize close modal coupling and non-stationary response. The FFT technique can on site verify the quality of the measurements, but its frequency resolution is low and damping estimates are unreliable. The ARMAV method allows for gaining high-frequency resolution. However, it is strictly related to the stationary hypothesis. It is a general conclusion that we can improve the quality of the analysis and get more precise characteristics of the signal by these three methods. In addition, the WD combined with ARMAV seems to be the best case in quantitative analysis of fast-changing vibration signals.     

Shaft angular misalignment detection using acoustic emission

Shaft angular misalignment (SAM) is a common and crucial problem in rotating machinery. Misalignment can produce several shortcomings such as premature bearing failure, increase in energy consumption, excessive seal lubricant leakage and coupling failure. Vibration analysis has been traditionally used to detect SAM; however, it presents some drawbacks i.e. high influence of machine operational conditions and strong impact of the coupling type and stiffness on vibration spectra. This paper presents an extensive experimental investigation in order to evaluate the possibility of detecting SAM, using acoustic emission (AE) technique. The test rig was operated at under different operational conditions of load and speed in order to evaluate the impact on the AE and vibration signature under normal operating conditions. To the best of the author’s knowledge, this is the first attempt to use AE for the detection of SAM under varying operational conditions. A comparative study of vibration and AE was carried out to demonstrate the potentially better performance of AE. The experimental results show that AE technique can be used as a reliable technique for SAM detection, providing enhancements over vibration analysis.     

一种新的数字散斑振动定量分析系统

在数字散斑干涉(DSPI)测量方法中，数字散斑时间平均法测量振动时得到的是贝塞尔条纹，其定量分析比较困难。该文采用贝塞尔条纹准相移技术进行数字散斑振动定量分析，即在参考光路中引入和物体同频率的偏置参考振动,当参考振动的相位改变时,振动条纹会产生移动,这相当于静态余弦条纹的相移,可以采用相移算法对数字散斑振动测量的贝塞尔条纹进行定量分析。文中开发了一种新的数字散斑振动定量分析系统，研制了一种低压光学相移器和测量控制电路，给出了圆周固定圆片和四周固定方铜板的振动测量结果。实验结果表明：采用本系统可以方便地定量测出物体的振动模态。     

Self-mixing interference in an all-fiberized configuration Er-Yb codoped distributed Bragg reflector laser for vibration measurement

Self-mixing sensing technique can be used for measuring distances, displacements, velocities and vibration. In this paper, for good sensitivity vibration measurement system, self-mixing vibrator using an all-fiberized configuration Er³⁺-Yb³⁺ Distributed Bragg Reflector (EYDBR) laser is proposed and investigated for the first time. Results obtained demonstrate that all-fiberized configuration EYDBR laser present a powerful tool for the advancement of self-mixing vibration sensor and provide a potential remote measurement of the vibration compared with the optical feedback in other traditional fiber lasers.     

外场作用下聚合物滞后生热效应

为了研究振动参数对聚合物黏弹性能及塑化成型过程的影响,深入分析了振动场的作用机理,揭示了相位角与滞后生热率之间的关系,得出了振动场作用下聚合物塑化成型速率表达式,最后通过聚对苯二甲酸乙二醇酯(PET)动态毛细管挤出以及多维振动塑化成型设备进行实例计算和实验研究,实验结果和理论计算值符合得很好,并得出结论: PET塑化速率随振动频率的增加呈先增加后减小的趋势,当激振频率趋向于材料固有频率时(振动频率约为15 Hz时),PET塑化速率达到最大值,当振幅为6 MPa时,其值约为22 g/min,为相同振幅下,频 关键词： 振动场 滞后生热 相位角 低温成型     

Optical heterodyne measurement of in-plane vibrations

An optical heterodyne technique which detects the frequency shift of light reflected from a point in motion can be successfully used for in-plane vibration measurements. Principles and results of preliminary experiments are described.