合肥光源单束团下束团长度和能散的测量

根据同步光与储存环中的束流信号具有相同的时间结构的原理,测量同步光脉冲的半高全宽值可以计算出束团的长度。根据合肥光源的特点和实际需要,选择快速光电接收器搭配高速高带宽示波器作为在线测量束团长度和纵向分布等的主要手段。对单束团模式下束团长度随流强和高频腔腔压的变化趋势进行了测量。测量结果表明:束团长度与腔压的0.3次方成反比,比理论值0.5小;而束团长度随流强的增长率为2.0 ps/mA。通过测量纵向量子寿命进行了能散随流强变化的间接测量,结果表明,束团的拉伸是能散变化和势阱效应共同作用的结果。     

束团磁压缩的高阶限制

研究了束团压缩中的高阶效应, 结果表明存在高阶项的压缩限制, 压缩后束团的长度比线性理论值长, 初始为均匀分布的束团较高斯分布更易压缩, 在相同的加速段与磁压缩器条件下, 其所获得的束团长度较短, 最后作了数值计算, 结果与理论相符.     

合肥光源基于同步光的测量与研究

介绍了合肥光源同步光测量系统, 包括条纹相机系统、快速光电测量束团长度系统、束团横向截面测量系统和光位置测量系统. 利用条纹相机系统和快速光电测量束团长度系统进行了束团长度测量和束团伸长效应的研究. 利用束流截面测量系统进行了六极铁对横向不稳定性抑制效果和横向反馈系统反馈效果的测量研究. 光位置测量系统采用丝型光位置检测器和自行研制了对数处理器, 用于测量光源点的束流位置和角度.     

HIAF-BRing束团合并过程中的束流负载效应模拟

强流重离子加速器HIAF-BRing在加速完成后进行束团合并，为研究BRing中的束流负载效应对束团合并的影响，对238U35+束流进行了粒子跟踪模拟。模拟结果显示，在束团合并过程中，束流负载效应引起束团长度和束团中心位置的振荡，导致束流动量分散和束团长度的增长。束团合并过程中尾场电压以及不同束团间尾场的耦合导致的势阱畸变，是引起束团长度和束团中心振荡及束流发射度增长的原因。为了降低束流负载效应的影响，采用多谐波前馈系统进行补偿，达到了补偿束团合并过程中的束流负载效应的目的，从而确保了BRing中引出束流的品质，同时根据模拟结果确定了前馈系统需要覆盖的频率范围和需要补偿的最大尾场电压。     

合肥光源基于同步光的测量与研究

介绍了合肥光源同步光测量系统,包括条纹相机系统、快速光电测量束团长度系统、束团横向截面测量系统和光位置测量系统.利用条纹相机系统和快速光电测量柬团长度系统进行了束团长度测量和束团伸长效应的研究.利用束流截面测量系统进行了六极铁对横向不稳定性抑制效果和横向反馈系统反馈效果的测量研究.光位置测量系统采用丝型光位置检测器和自行研制了对数处理?用于测量光源点的束流位置和角度.     

北京正负电子对撞机(BEPC)束团长度的测量

讨论了利用J/ψ粒子次级产物中带电粒子顶点测量对撞机束团长度的方法,并给出北京正负电子对撞机(BEPC)对撞点处的束团长度.     

直线加速器中双向高斯密度分布电荷束团发射度增长的比率关系

采用直线加速器中的空间电荷束团的有限圆柱模型,并假设该有限圆柱体电荷密度分布在横向r和纵向z都满足高期分布,推导得到了该电荷束团的自场能与发射度增长公式;通过数值模拟计算,给出了束流发射度增长随束团参数和加速器系统参数变化的图表曲线,讨论了该双向高期密度分布电荷束团发射度增长的比率关系.     

合肥光源测量束团纵向精细结构的单光子计数系统设计

本文介绍了用单光子计数法测量束团纵向精细结构的原理.介绍了合肥同步辐射光源测量束团纵向精细结构的单光子计数系统的设计.由于单光子计数法具有高时间分辨率(2ps)和大的动态测量范围(10⁵)等优点,所以该系统不仅可以测量束团长度,而且可以精密测量单束团的纯净度.最后,分析了该系统的性能,并讨论了该系统在尾场和纵向阻抗的研究、束团伸长效应的研究以及影响单束团不纯净机理的研究中的应用.     

加速器束流诊断技术的新进展

介绍了加速器束流诊断技术的新进展, 包括束流位置测量技术、束团横向尺寸测量技术和束团长度测量技术. 束流位置测量技术主要介绍具有高位置分辨率的腔型束流位置检测器和数字束流位置处理技术. 束团尺寸测量技术主要介绍高空间分辨率的激光丝扫描器、光学渡越辐射和光学衍射辐射技术. 束团长度测量技术主要介绍高时间分辨率的相干辐射光谱技术、RF横向偏转腔、RF零相位技术和电光采样技术.     

用电光采样法测量相对论电子束团长度

 介绍了电光采样法测量电子束束团长度的实验原理和装置,理论分析并模拟计算了被测电子束团库仑场分布、ZnTe晶体的电光效应与束团电场的关系,并利用琼斯矩阵法分析了探测光通过电光晶体时在束团电场作用下的偏振变化、测量信号与束团长度的关系等。分析表明：测量中应使束团库仑场垂直于ZnTe的［001］方向,探测光偏振方向与ZnTe晶体y″轴成45°或者135°夹角,1/4波片快轴与探测光偏振方向夹角应取45°,这时平衡探测器输出信号与束团库仑场Eb成正比。1/4波片的作用是将电光晶体的工作点从非线性段移到线性段,平衡探测的作用是简化信号与Eb的关系,并提高信噪比。为实际测量应用提供参考。     

RF deflecting cavity design for bunch length measurement of photoinjector at Tsinghua University

RF deflecting cavity can be used for bunch length measurement and is designed to diagnose the beam produced by the photocathode electron gun which was built at Tsinghua University for the Thomson scattering experiment.Detailed discussion and calculation for measuring the 3.5 MeV bunch and another with further acceleration to 50 MeV,which is under development,are presented.A standing-wave deflecting cavity working at 2856 MHz is designed and the power feeding system has been planned.     

RF deflecting cavity design for bunch length measurement of photoinjector at Tsinghua University

RF deflecting cavity can be used for bunch length measurement and is designed to diagnose the beam produced by the photocathode electron gun which was built at Tsinghua University for the Thomson scattering experiment. Detailed discussion and calculation for measuring the 3.5 MeV bunch and another with further acceleration to 50 MeV, which is under development, are presented. A standing-wave deflecting cavity working at 2856 MHz is designed and the power feeding system has been planned.     

Bunch length measurement at Tsinghua Thomson scattering X-ray source

The length of electron beam from a photocathode RF gun is determined by a spectrometer, according to the relative energy spread induced by the bunch length during the acceleration in a linac. For a photocathode RF gun, different laser injected phase and beam charge are studied. The compression is changed for the different laser phases, as from 10° to 30°, and the bunch length is lengthened due to the strong longitudinal space charge force, caused by the increased charge.     

粒子束团状态对测量束流发射度及能量的影响

为了验证国产质子注入器的参数是否满足需求,注入器团队设计了束流测量系统用于测量国产质子直线注入器束流的流强、发射度、能量以及能散等关键指标。此测量系统包含了采用变聚焦法测量发散度、采用分析磁铁测量束流能量和能散的主要功能。利用束流输运线设计软件Tracewin(版本2.11.4.1)进行了系统束线的物理设计,对束测系统测量质子束流的发散度和能量的精度进行了模拟计算。由于经过RFQ-(APF)DTL加速后的粒子束团为“拖尾”的非理想粒子束团,需要针对非理想束团对束测系统测量发射度和能量产生的影响进行分析。通过对模拟计算结果的分析,发现相对于测量理想粒子束团的结果非理想粒子束团对束测系统测量发射度精度影响较大;非理想粒子束团对束测系统测量能量精度影响较小。     

Electro-optical sampling non-synchronous delay scanning measurement of electron beam bunch length at BFEL

The Electro-optical sampling delay scanning technique can be used for electron beam bunch length measurement.A novel non-synchronous delay scanning technique based on the electro-optical sampling measurements is presented.Based on Beijing Free Electron Laser(BFEL),the electron beam bunch length was measured with the electro-optical sampling technique for the first time in China.The result shows that the electron beam bunch length at BFEL is about 5.6±1.2 ps.     

Emittance-dominated long bunches in dual harmonic RF system

The storage of long bunches for long time intervals needs flattened stationary buckets with a large bucket height. The longitudinal motion of the initially mismatched beam has been studied for both the single and dual harmonic RF systems. The RF amplitude is determined to be r.m.s wise matched. The bucket height of the single harmonic system is too small even for shorter bunch with only 20% increased energy spread. The Halo formation and even debunching can be seen after a few synchrotron periods for single particles with large amplitude. In the case of small energy spread for a cooled beam, Coulomb interaction cannot be ignored. The external voltage has to be increased to keep the r.m.s bunch length unchanged. The new voltage ratio R(N) simplifies physics for the emittance-dominated bunches with modest particle number N. For the single harmonic system, substantial amount of debunching occurs without increasing the external voltage, but very little if the RF amplitude is doubled. Results from the ORBIT tracking code are presented for the 1 GeV bunch in the HESR synchrotron, part of the GSI FAIR project.     

Bunch length measurement using a traveling wave RF deflector

RF deflectors can be used for bunch length measurement with high resolution. This paper describes a completed S-band traveling wave RF deflector and the bunch length measurement of the electron beam produced by the photocathode RF gun of the Shanghai DUV-FEL facility. This is the first time that such a transverse RF deflector has been developed and used to measure the bunch length of picosecond order in China. The deflector's VSWR is 1.06, the whole attenuation 0.5 dB, and the bandwidth 4.77 MHz for VSWR less than 1.1. With a laser pulse width of 8.5 ps, beam energy of 4.2 MeV, and bunch charge of 0.64 nC, the bunch lengths for different RF input power into the deflector were measured, and an averaged rms bunch length of 5.25 ps was obtained. A YAG crystal is used as a screen downstream of the deflector, with the calibrated value of 1 pix = 136 μm.     

RF deflecting cavity for bunch length measurement in Tsinghua Thomson scattering X-ray source

An RF deflecting cavity used for bunch length measurement has been designed and fabricated at Tsinghua University for the Thomson Scattering X-Ray Source.The cavity is a 2856 MHz,π-mode,3-cell standing-wave cavity,to diagnose the 3.5 MeV beam produced by photocathode electron gun.With a larger power source,the same cavity will again be used to measure the accelerated beam with energy of 50 MeV before colliding with the laser pulse.The RF design using MAFIA for both the cavity shape and the power coupler is reviewed,followed by presenting the fabrication procedure and bench measurement results of two cavities.     

First experimental research of the bunch compressor at CAEPLI

Magnetic bunch compressor is one of the key technologies on the path to next generation accelerator driven facilities. In this paper we report the design principles and the first experimental research of the bunch compressor developed at Chinese Academy of Engineering Physics (CAEP). The length of the bunch after compressor is found to be about 0.7 ps (rms) and the peak current exceeds 500 A when operated in the optimized condition. The sensitivity of the bunch length on the phase of the acceleration field and magnetic field of the bunch compressor was also measured and analyzed.     

外注入式独立调谐微波电子枪的概念设计

为得到微脉冲束团长度在百fs量级且高重复频率,设计了一种紧凑型的强流电子枪结构独立调谐微波热发射电子枪。该电子腔具有双驻波加速腔,两个驻波加速腔之间相互没有耦合,可以分别独立地馈入功率、调节相位。通过优化功率与相位,可以得到较优的束流品质,同时避免了磁铁和激光系统的使用,使得结构更加紧凑。并采用外注入式结构增大流强、降低能散度,同时消除电子反轰对阴极的负面影响。对不同结构参数的腔体进行1维和3维束流动力学计算,可以得到较为理想的腔体参数。通过调节预注入器的馈入功率和粒子入射相位,可以进一步的压缩束团长度。