M2SiO4:Re(M=Mg,Ca,Ba;Re=Ce3+,Tb3+)的发光性能

合成了系列M2SiO4∶Re(M=Mg,Ca,Ba; Re= Ce3 ,Tb3 )样品,研究了样品在真空紫外区域的激发光谱和发射光谱.从激发谱可以看出:M2SiO4∶Re(M=Mg,Ca,Ba; Re= Ce3 ,Tb3 )在147,172 nm有很强的吸收带.用Mg,Ca完全取代Ba2SiO4∶Tb3 中的Ba ,相对应的晶体的晶格参数逐渐增大,晶场的能量逐渐减少,其激发光谱随着碱土离子半径的增加向长波方向移动.在172 nm真空紫外光激发下,观察到M2SiO4∶Re(M=Mg,Ca,Ba; Re=Tb3 和M2SiO4∶Re(M=Mg,Ca,Ba; Re= Ce3 ,Tb3 )特征发射;在真空紫外激发下,随着M2SiO4∶Re(M=Mg,Ca,Ba; Re= Ce3 ,Tb3 )中Ce3 含量的增加,M2SiO4∶Re的特征发射明显减弱,并分析讨论了相关发光现象的成因.     

M2SiO4：Re(M=Mg,Ca,Ba;Re=Ce3+,Tb3+)的发光性能

合成了系列M₂SiO₄:Re(M=Mg,Ca,Ba;Re=Ce³⁺,Tb³⁺)样品,研究了样品在真空紫外区域的激发光谱和发射光谱。从激发谱可以看出:M₂SiO₄:Re(M=Mg,Ca,Ba;Re=Ce³⁺,Tb³⁺)在147,172nm有很强的吸收带。用Mg,Ca完全取代Ba₂SiO₄:Tb³⁺中的Ba,相对应的晶体的晶格参数逐渐增大,晶场的能量逐渐减少,其激发光谱随着碱土离子半径的增加向长波方向移动。在172nm真空紫外光激发下,观察到M₂SiO₄:Re(M=Mg,Ca,Ba;Re=Tb³⁺和M₂SiO₄:Re(M=Mg,Ca,Ba;Re=Ce³⁺,Tb³⁺)特征发射;在真空紫外激发下,随着M₂SiO₄:Re(M=Mg,Ca,Ba;Re=Ce³⁺,Tb³⁺)中Ce³⁺含量的增加,M₂SiO₄:Re的特征发射明显减弱,并分析讨论了相关发光现象的成因。     

红色LiM(M=Ca,Sr,Ba)BO_3∶Re~(3+)(Re=Eu,Sm)发光材料的特性

采用固相法制备了红色LiM(M=Ca,Sr,Ba)BO3∶Re3+(Re=Eu,Sm)发光材料,研究了材料的发光性能。研究发现LiM(M=Ca,Sr,Ba)BO3∶Eu3+材料呈现多峰发射,最强发射分别位于610,615,613 nm处,分别监测这三个最强峰,所得激发光谱峰值位于369,400,470 nm。LiM(M=Ca,Sr,Ba)BO3∶Sm3+材料也呈多峰发射,分别对应Sm3+的4G5/2→6H5/2、4G5/2→6H7/2和4G5/2→6H9/2跃迁发射;分别监测602,599,597 nm三个最强发射峰,所得激发光谱峰值位于374,405 nm。研究了激活剂浓度对材料发射强度的影响,结果随激活剂浓度的增大,发射强度先增强后减弱,即,存在浓度猝灭效应。实验表明,加入电荷补偿剂Li+、Na+或K+均可提高LiM(M=Ca,Sr,Ba)BO3∶Re3+(Re=Eu,Sm)材料的发射强度。     

Ba3Tb(BO3)3:Ce3+:一种白光LED用绿色荧光粉

采用高温固相法合成了Ba3Tb(BO3)3和Ba3Tb(BO3)3:Ce3+两种绿色荧光粉,并研究了材料的发光性质.Ba3Tb(BO3)2材料呈多峰发射,发射峰位于439,493,547,589和629 nm,分别对应Tb3+的5D3→7F4和5D4→7F1=6,5,4,3跃迁发射,主峰为547 nm;监测547 nm发射峰,所得激发光谱由4f75d1宽带吸收(200-330 nm)和4f4f电子吸收(330-400 nm)组成,主峰为380 nm.以Ce3+激活Ba3Tb(BO3)3,所得Ba3Tb(BO3)3:Ce3+与Ba3Tb(BO3),材料的发射光谱分布相同,但发射强度明显增强,说明Ce3+对Tb3+产生了很好的敏化作用;监测547 nm最强发射峰,所得激发光谱为宽带,主峰位于360 nm.改变H3BO3量,Ba3Tb(BO3)3:Ce3+材料的发射强度随之变化,当H3BO3过量15 wt%时,发射强度最大.上述研究结果表明Ba3Tb(BO3)3:Ce3+是一种很好的适于UV-LED管芯激发的白光LED用绿色荧光粉.     

红色LiMBO3 : Re3+(Re=Eu,Sm) 发光材料的特性

采用固相法制备了红色LiM(M=Ca, Sr, Ba)BO₃ : Re³⁺(Re=Eu, Sm)发光材料,研究了材料的发光性能。研究发现LiM(M=Ca, Sr, Ba)BO₃ : Eu³⁺材料呈现多峰发射,最强发射分别位于610,615,613 nm处,分别监测这三个最强峰,所得激发光谱峰值位于369,400,470 nm。LiM(M=Ca, Sr, Ba)BO₃ : Sm³⁺材料也呈多峰发射,分别对应Sm³⁺的⁴G_5/2→⁶H_5/2、⁴G_5/2→⁶H_7/2和⁴G_5/2→⁶H_9/2跃迁发射;分别监测602,599,597 nm三个最强发射峰,所得激发光谱峰值位于374,405 nm。研究了激活剂浓度对材料发射强度的影响,结果随激活剂浓度的增大,发射强度先增强后减弱,即,存在浓度猝灭效应。实验表明,加入电荷补偿剂Li⁺、Na⁺或K⁺均可提高LiM(M=Ca, Sr, Ba)BO₃ : Re³⁺(Re=Eu, Sm)材料的发射强度。     

MO-Y2O3-B2O3:Re(M=Mg,Sr;Re=Eu,Tb)的真空紫外光谱特性

采用高温固相反应法合成了掺杂Eu3 及Tb3 的17MO-7.88Y2O3-75B2O3样品,研究了它们的光谱特性,结果表明,MO-T2O3-B2O3基质在真空紫外(VUV)区有很强的吸收,MgO-Y2O3-B2O3:Eu在147nm真空紫外光激发下产生对应于Eu3 的5D0→7FJ(J=1,2,3,4)跃迁的590和613 nm强发射峰;MgO-Y2O3-B2O3:Eu中Sr的引入使材料体系在147 nm附近的吸收和在613 nm附近的发射获得明显增强;MgO-Y2O3-B2O3:Tb的真空紫外激发谱除在147 nm附近的基质吸收外,还有对应于Tb3 的4f75d→4f8跃迁位于170,178,195,204,225 nm左右的一组谱峰,两者相互叠加使得材料在真空紫外区(120～220 nm)内都有很好的吸收.     

Ca_2SrAl_2O_6荧光粉中Ce~(3+)和Tb~(3+)的光谱性能研究及能量传递

采用高温固相法合成了用于紫外芯片(UVLED)激发的绿色荧光粉Ca2SrAl2O6:Ce3+,Tb3+。测量了其激发光谱和发射光谱,结果显示,材料的发射谱由峰值位于497,545,595和623nm的4组窄带组成,其中位于545nm的发射峰最强,样品能发射很好的绿光;监测545nm发射峰,得到的激发谱由位于320～400nm之间的激发带组成,能被UVLED很好地激发。研究了Ca2SrAl2O6荧光粉中Ce3+对Tb3+发光的敏化现象,发光的敏化作用缘于Ce3+和Tb3+之间的高效无辐射能量传递。共掺激活剂的最佳掺杂浓度为4mol%。     

N^＋（N=Li,Na,K）对发光材料M3（M=Ca,Sr,Ba）Y2（BO3）4：Eu^3＋光谱的影响

采用高温固相反应方法在空气中制备了M3(M=Ca,Sr,Ba)Y2(BO3)4∶Eu3 红色发光材料,测量结果显示,材料的主发射峰均位于613 nm处,监测613 nm发射峰时,所得材料的激发光谱相同。研究了Li ,Na 和K 对M3(M=Ca,Sr,Ba)Y2(BO3)4∶Eu3 材料激发与发射光谱的影响,结果显示,加入Li ,Na 和K 后,M3(M=Ca,Sr,Ba)Y2(BO3)4∶Eu3 材料的激发与发射光谱的峰值位置并不发生变化,但材料的激发与发射光谱的峰值强度均得到了不同程度的增强。在Li ,Na 和K 掺入浓度相同的条件下,研究发现,与加入Na 和K 时相比,加入Li 时,M3(M=Ca,Sr,Ba)Y2(BO3)4∶Eu3 材料的激发与发射光谱的峰值增强效果最明显。进而研究了Sr3Y2(BO3)4∶Eu3 材料发射峰强度随Li 掺杂浓度的变化情况,结果表明,随着Li 掺杂浓度的增大,Sr3Y2(BO3)4∶Eu3 材料发射峰强度先增大后减小,在Li 浓度为5 mol%时到达峰值,约为未掺杂时的两倍。     

（Sr,Ba）Al12O19∶RE^3＋（RE=Ce,Tb）的VUV发光及Ce^3＋→Tb^3＋的能量传递

采用高温固相反应合成磁铅矿型(Sr,Ba)Al12O19∶RE3 (RE=Ce,Tb)发光材料,X射线衍射结果证明生成单一磁铅矿型结构。Ce3 产生302nm的发射峰和340nm左右的不太明显的肩,分别对应于5d→2F5/2和5d→2F7/2跃迁;激发光谱显示两个宽带峰,158nm峰对应于基质吸收,260 nm峰是由4f-5d跃迁引起的。Tb3 的发射光谱显示特征的5D3→7Fj(j=2,3,4,5)和5D4→7Fj(j=4,5,6)跃迁;在激发光谱中,160nm左右的峰是由基质吸收和Tb3 -O2-电荷迁移带交迭产生的,193nm峰是Tb3 的4f-5d自旋允许跃迁引起的,233nm弱的峰是自旋禁戒4f-5d跃迁产生的。Ce3 的发射和Tb3 的f-f跃迁吸收(~320 nm)完全交迭,并且Tb3 的发光强度随Ce3 的浓度增加而增强,从激发光谱看出,Tb3 发光部分来自于Ce3 的吸收,具有Ce3 →Tb3 能量传递。     

LiM(M=Ca,Sr,Ba)BO_3∶Tb~(3+)材料光谱特性研究

采用固相法制备了绿色LiM(M=Ca,Sr,Ba)BO3:Tb3+发光材料.测量结果显示材料均可被紫外(350～410 nm)光激发,发射绿光.研究了Tb3+浓度对材料发射光谱的影响,结果显示,随Tb3+浓度的增大,发射光谱峰位未发生变化,但其强度呈现出先增大后减小的趋势,即:存在浓度猝灭效应.加入电荷补偿剂Li+,Na+和K+提高了LiM(M=Ca,Sr,Ba)BO3:Tb抖材料的发射强度.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.