The Scatter Characteristic to Sky Temperature of Metal Targets

This paper discusses the theory foundation of an engineering practical method for measuring the microwave radiation characteristic of metal target— —scaling shrunk simulation measuring method. The scatter theory was managed to analyze and compute the microwave radiation characteristic of metal target. And the actual measurement shows the method is feasible.     

高精度非致冷长波红外热像仪的辐射标定

为使非致冷长波红外热像仪在不同温度下保持较高的测温精度,建立了考虑探测器工作温度效应的非致冷长波红外热像仪的辐射标定模型。对非致冷长波红外热像仪进行辐射标定实验,在不同黑体温度和不同亮度增益值条件下,获得了16组图像灰度与探测器工作温度之间的函数关系,建立了目标温度的数学计算模型,并对定标结果进行了实验验证。结果表明：在25～40℃,探测器的工作温度效应可做线性化处理,且与目标温度无关。通过设定合适的亮度增益值可使红外热像仪的测温误差〈0.5℃,极大地提高了非致冷长波红外热像仪在不同温度环境下的测温精度。     

锥形剖面径向复合超声换能器的机电等效电路

研究了一种锥形剖面径向复合超声换能器。该换能器由一个等截面内金属圆环、一个轴向极化的压电陶瓷圆环和一个锥形剖面外金属圆环沿径向复合而成,且换能器的径向尺寸远大于高度。锥形剖面外金属圆环满足关系式h=h₀r,h₀为厚度变化常数。基于平面应力径向振动理论,推导了换能器的机电等效电路,得到了共振频率方程和反共振频率方程,进而研究了换能器的振动特性。并将理论计算的第1阶、第2阶径向共振频率和反共振频率与数值仿真结果相比较,二者结果一致。研究表明:锥形剖面换能器第1阶、第2阶径向共振频率、反共振频率、有效机电耦合系数不仅与换能器各部分的材料、径向几何尺寸有关,还与h₀有关。h₀越大,第1阶径向共振频率、反共振频率越大,有效机电耦合系数先增大后减小。与等截面相比,锥形剖面换能器沿径向向外辐射声波,辐射面积更大,辐射声功率更高,指向性更好。      

Invisible anti-cloak with elliptic cross section using phase complement

Based on the theory of phase complement,an anti-cloak with circular cross section can be made invisible to an object outside its domain.As the cloak with elliptic cross section is more effective to make objects invisible than that with circular cross section,a scaled coordinate system is proposed to design equivalent materials of invisible anticloak with elliptic cross section using phase complement.The cloaks with conventional dielectric and double negative parameters are both simulated with the geometrical transformations.The results show that the cloak with elliptic cross section through phase complement can effectively hide the outside objects.     

Numerical investigation of multi-beam laser heterodyne measurement with ultra-precision for linear expansion coefficient of metal based on oscillating mirror modulation

This paper proposes a novel method of multi-beam laser heterodyne measurement for metal linear expansion coefficient. Based on the Doppler effect and heterodyne technology, the information is loaded of length variation to the frequency difference of the multi-beam laser heterodyne signal by the frequency modulation of the oscillating mirror, this method can obtain many values of length variation caused by temperature variation after the multi-beam laser heterodyne signal demodulation simultaneously. Processing these values by weighted-average, it can obtain length variation accurately, and eventually obtain the value of linear expansion coefficient of metal by the calculation. This novel method is used to simulate measurement for linear expansion coefficient of metal rod under different temperatures by MATLAB, the obtained result shows that the relative measurement error of this method is just 0.4%.     

积分球光源分布温度对宽波段光学遥感器绝对辐射定标的影响及其校正

实测了积分球输出光谱辐亮度分布曲线,并得到积分球光源的分布温度。从理论上分析了积分球光源分布温度影响宽波段光学遥感器绝对辐射定标精度的原因和机理,并仿真计算了包括积分球和太阳在内的几种不同分布温度光源定标某宽波段光学遥感器时得到的定标系数。仿真结果表明,不同分布温度间的定标系数最大差别大于2%。在此基础上提出了积分球光源分布温度影响绝对辐射定标系数的校正方法,为提高宽波段遥感器的辐射定标精度和遥感图像辐射校正提供了思路和依据。     

固体火箭发动机羽流辐射光谱测温方法研究

固体火箭发动机羽流具有高温、高速与强辐射特征,羽流温度是发动机工作状态与性能的重要表征参数。准确测量固体火箭发动机羽流温度对了解发动机内部燃烧情况以及发动机综合性能具有重要的参考价值。随着激光与光谱学的发展,激光光谱技术逐步应用于固体推进剂燃烧及发动机羽流温度测量。辐射光谱测温法通过测量火焰辐射光谱来实现温度的非接触在线测量,具有测温范围宽、响应快及可靠性高等优点,可应用于固体火箭发动机羽流温度测量。在此提出了基于火焰辐射光谱的固体火箭发动机羽流温度测量方法,采用350～1 000 nm波段光纤光谱仪搭建了发动机羽流火焰辐射光谱测量系统,利用标准辐射黑体炉开展光谱仪响应系数标定,获得响应系数随波长的变化曲线,并以此用作羽流辐射光谱数据修正。之后将该测量系统应用于标准Φ118固体火箭发动机地面试验,开展典型12%铝质量含量推进剂发动机羽流辐射光谱实验测量,选取不同时刻羽流辐射光谱分析了发动机羽流辐射光谱特征,并利用双色法灰性判断原理对羽流火焰灰体特性进行讨论,验证在675～745 nm波段发动机羽流火焰辐射可近似认为灰体,该波段辐射率随波长变化最大相对偏差为4.01%,相对均方差为1.53%。因此,基于普朗克辐射定律开展辐射光谱拟合参数获得不同时刻羽流温度与辐射率参数,并讨论测量结果与发动机工作状态的关系。最后,开展12%,15%与19%铝质量含量的不同推进剂配方固体火箭发动机羽流辐射光谱测量,将辐射光谱法温度测量值与理论热力计算值进行比较,两者最大偏差值为5.40%,讨论了不同铝含量推进剂发动机羽流辐射光谱特征,并结合温度与辐射率测量结果,分析了固体推进剂铝含量对辐射光谱、羽流温度及辐射率的影响。通过固体火箭发动机羽流辐射光谱测温方法研究,为固体火箭发动机性能评估及推进剂配方优化等研究提供了有效的羽流参数测量手段。分析获得的推进剂铝含量对发动机羽流辐射光谱、温度及辐射率参数的影响,为降低固体发动机羽流特征信号提供了重要的实验数据支撑。     

Statistical synthesis of multiantenna ultrawideband radiometric complexes

An optimum signal processing algorithm of radiometric imaging has been synthesized for the first time using multiantenna ultrawideband (UWB) radiometric complexes (RMCs). Radiometric images (RMI) are interpreted physically as intensity depending on the angular coordinates or the spectral radio brightness averaged in the operation frequency band. In accordance with the synthesized algorithm, a structural scheme of ultrawideband radiometric complexes has been developed. An analytical expression for the ambiguity function of radiometric complexes has been obtained. The ambiguity function is modeled in the case of processing narrowband and ultrawideband radiometric signals. As follows from the analysis of the results, new elements of the theory of optimum processing of UWB radiometric signals with the involvement of multielement antenna systems are an important tool in creating highly accurate, biologically and ecologically safe complexes for studying various media and objects.     

金属铜的晶格结构与热力学性质的第一性原理计算

基于第一性原理,利用密度泛函理论(DFT)和密度泛函的微扰理论(DFPT),以及广义梯度近似(GGA),研究了过渡金属Cu的晶体结构、能量、电子能带和态密度、声子的能带结构和态密度,以及其在298.15K下的热容,体积模量,格林艾森参数和体胀系数等热力学函数并与实验值作了对比.通过分析Cu的晶格几何与能量之间的关系,讨论了金属Cu的固-液相变与晶格声子振动能量之间可能的内在联系,首次提出直接得到Cu熔化温度Tm的静力学方法,研究了熔化温度与压强的关系.计算结果与实验值符合较好,明显优于分子动力学模拟的结果.     

Numerical investigation of the effect of soot aggregation on the radiative properties in the infrared region and radiative heat transfer

The effect of aggregation on soot radiative properties in the infrared region of the spectrum is numerically investigated using Rayleigh-Debye-Gans theory for fractal aggregates (RDG-FA). In order to use the RDG-FA theory for a wide range of aggregate sizes and wavelengths, the predicted phase functions, scattering and absorption coefficients are compared with a more accurate theory, the integral equation formulation for scattering—IEFS. The importance of scattering when compared with absorption is investigated, as well as the effect of aggregation on the phase function shape and on the scattering cross section. It is concluded that in the case of small aggregates formed with small primary particles the scattering coefficient is negligible compared with the absorption coefficient, and scattering and aggregation of primary particles can be ignored. Thus, the Rayleigh approximation can be used leading to isotropic scattering. In the case of large aggregates constituted by large primary particles, aggregation becomes important and the scattering cross section is of the same order of magnitude of the absorption cross section. Moreover, the phase function becomes highly peaked in the forward direction. Therefore, the Rayleigh and the equivalent volume Mie sphere approximations are not valid, and the RDG-FA method emerges as a good compromise between accuracy and simplicity of application. However, radiative transfer calculations between two infinite, parallel, black walls show that scattering may always be neglected in the calculation of total radiative heat source and heat fluxes to the walls. The minor influence of scattering on the accuracy of the predictions is explained by the shift between the spectral region where scattering is important and the region where the spectral radiative heat source is large.     

金属铜的晶体结构与热力学性质的第一性原理计算

基于第一性原理,利用密度泛函理论(DFT)和密度泛函的微扰理论(DFPT),以及广义梯度近似(GGA),研究了过渡金属Cu的晶体结构、能量、电子能带和态密度、声子的能带结构和态密度,以及其在298.15 K下的热容,体积模量,格林艾森参数和体胀系数等热力学函数并与实验值作了对比.通过分析Cu的晶格几何与能量之间的关系,讨论了金属Cu的固-液相变与晶格声子振动能量之间可能的内在联系,首次提出直接得到Cu熔化温度T_m的静力学方法,研究了熔化温度与压强的关系.计算结果与实验值符合较好,明显优于分子动力学模拟的结果.     

电热法测量固体线胀系数实验的改进

设计了控温电路并改进了测量方法,消除了电热法测量固体线胀系数实验中,由于被测固体棒的线膨胀速度、系统加热速度及测温器响应速度不同步而引起的误差.     

畸形波电磁散射特性分析及其特征识别标识的研究

针对弱非线性的Longuet-Higgins模型在模拟强非线性畸形波海面时所存在的问题,采用修正的相位调制法模拟一维畸形波时间、空间波面,该方法能够实现畸形波的定时定点生成,并且其波形既能保持目标谱的频谱结构,又能较大程度地满足波浪序列的统计特性.同时,基于改进的双尺度(TSM)法及时域有限差分法建立畸形波的电磁散射模型,经过相对平均偏差和均方根偏差误差分析后,基于TSM法研究分析了畸形波及其背景海面波的归一化雷达散射截面(NRCS)的计算结果.实验表明,合成孔径雷达成像中畸形波的NRCS比背景波要小,即畸形波的合成孔径雷达图像成像比背景波要灰暗,因此可以将NRCS作为畸形波的特征识别标识.通过分析研究不同极化方式、入射角、入射频率条件下畸形波与背景波面的电磁散射特性实验数据得出:当二者的NRCS差值大于-11.8 dB及以上时,即认为产生畸形波,这为实际的工程应用提供了参照标准.     

基于海面散射模型的全极化合成孔径雷达海洋环境探测关键技术参数设计仿真研究

技术参数设计研究是提升全极化SAR海洋环境探测能力的有效途径. 本文通过分析噪声等效后向散射系数和辐射分辨率与海洋环境探测的地球物理联系,提出一种全极化SAR关键技术参数设计方法. 采用全极化海面散射模型计算不同海洋环境条件下的雷达后向散射系数,据此确定全极化SAR对海探测的噪声等效后向散射系数,再将其作为合成孔径雷达方程输入参数,以辐射分辨率和信噪比的函数关系为约束条件,开展信噪比、辐射分辨率和系统功率孔径积等技术参数设计研究. 论文通过全极化海面散射模型的仿真计算,发现对海探测的噪声等效后向散射系数设计为-35.0 dB,可满足全极化SAR不同海洋环境条件的探测需求. 通过研究辐射分辨率与信噪比的函数关系,发现对海探测的最优信噪比为8.0 dB. C波段机载全极化SAR设计结果表明,由于兼顾了海洋环境探测需求,本文设计方法使得全极化SAR技术参数同时满足了海洋环境应用需求和系统设计要求. 关键词： 海面散射模型 全极化合成孔径雷达 海洋环境探测 技术参数设计     

从多波段图像中获取大气透过率的测量方法

提出了一种基于单帧多波段图像测量非气体吸收波段和弱气体吸收波段大气透过率的方法,可应用于相关光电工程中评估和修正大气衰减影响.首先,利用经过绝对辐射定标的图像采集设备获得辐射图像;其次,基于大气中图像退化光学模型与暗通道先验统计理论得到辐射图像暗通道对应的宽波段平均大气透过率;最后,结合特定波段消光系数和宽波段平均消光系数间的关系得到特定波段的大气透过率.实验对比分析表明:本文方法与能见度仪、激光雷达测量结果相关性较高,其中与能见度仪相比,相关系数在0.89和0.95之间,与激光雷达相比,相关系数在0.95和0.97之间;在1km近距离条件下与能见度仪、激光雷达测量结果平均相对偏差最高分别为9%和6%,在远距离条件下,与能见度仪测量结果相比,4km和6km平均相对偏差最高分别为15%和30%,与激光雷达测量结果相比,4km和6km平均相对偏差最高分别为9%和18%.     

温度相关核截面数据库在MCNP计算中的必要性研究

MCNP程序由于其几何模拟和核数据上的优越性,现在在反应堆的研究分析中已经得到较多应用。通过基准题的计算,定量地说明MCNP通过其自带的常温（294K）下的核素截面数据库不能够对反应堆进行非常准确的计算（由于反应堆内各种材料／位置的温度不同）,而且,它也不能够计算反应堆中与温度相关的量,如反应性温度系数。选用了一个带有不同温度下核素截面数据的MCNP输入格式的数据库,使用MCNP-4C对基准题进行了计算,发现计算结果与基准值符合得非常好。这说明通过使用不同温度下的核素截面数据库,MCNP可以准确计算温度系数和增殖系数等,从而说明在反应堆设计计算中制作不同温度下的核素截面库的必要性。Due to the advantage of geometry simulation and nuclear data, the code MCNP is now widely used in the reactor analysis. Based on our calculation of the fuel temperature reactivity coefficient benchmark, it is quantificationally proved that MCNP with its own cross section library can＇ t be used to simulate the reactor accurately and to calculate the temperature reactivity coefficient. Furthermore, we use MCNP- 4C with a database that contains temperature dependent nuclear cross sections to calculate the benchmark. The results are well agreement with benchmark results. This means that, with the temperature dependent nuclear cross sections library, MCNP can calculate the temperature reactivity coefficient and reactor multiplication factor accurately. So the temperature dependent nuclear cross section library should be processed to meet the requirement of reactor calculation.     

三维光学扫描技术逆向工程应用研究

针对三维扫描测量数据因为原始点云在获取时受环境等客观条件限制,存在不可避免的噪声点、飞点、重叠点云等现象,以致存在点云密度大、运算复杂、计算周期长等问题,本文以在逆向工程中具有将三维物体几何信息转换为计算机能直接处理的二维数字信号的功能的三维光学扫描技术为基础,研究了三维扫描技术应用的主要设备、常用软件、使用方法和实体建模商用软件,研究了其原理及数学模型;结合XJTUOM,制定了扫描策略,以某型号汽车皮带轮和减震器托盘为例进行了实践操作,结果表明:该设备能够满足在逆向工程的应用,其扫描精度接近原始数模的相似度为98%。     

Retrieval algorithm of quantitative analysis of passive Fourier transform infrared （FTRD） remote sensing measurements of chemical gas cloud from measuring the transmissivity by passive remote Fourier transform infrared

Passive Fourier transform infrared （FTIR） remote sensing measurement of chemical gas cloud is a vital technology. It takes an important part in many fields for the detection of released gases. The principle of concentration measurement is based on the Beer-Lambert law. Unlike the active measurement, for the passive remote sensing, in most cases, the difference between the temperature of the gas cloud and the brightness temperature of the background is usually a few kelvins. The gas cloud emission is almost equal to the background emission, thereby the emission of the gas cloud cannot be ignored. The concentration retrieval algorithm is quite different from the active measurement. In this paper, the concentration retrieval algorithm for the passive FTIR remote measurement of gas cloud is presented in detail, which involves radiative transfer model, radiometric calibration, absorption coefficient calculation, et al. The background spectrum has a broad feature, which is a slowly varying function of frequency. In this paper, the background spectrum is fitted with a polynomial by using the Levenberg-Marquardt method which is a kind of nonlinear least squares fitting algorithm. No background spectra are required. Thus, this method allows mobile, real-time and fast measurements of gas clouds.     

Reflectance Measurement of Lossy Metal Meshes in the Millimeter-Wave Range

The method of power reflectance measurement of small lossy metal meshes is suggested by evaluating the measured reflection coefficient in the vicinity of a resonance mode of quasi-optical resonator. The resonator is described by the equivalent circuit that includes coupling ohmic losses of the mesh. The multi-points reconstructing algorithm is suggested to restore power reflectance. This particular technique is suitable for reflectance measurements of lossy metal meshes and wire grids having overall small dimensions which are not relevant when employing standard free space techniques. Its validity is illustrated by reflectance measurements in W-band.