共查询到20条相似文献,搜索用时 109 毫秒
1.
热声压力波放大器的湍流模型及实验验证 总被引:2,自引:0,他引:2
热声压力波放大器是一种利用声学特性将压力波幅值进行放大的一种装置,它主要用来连接热声发动机和其驱动的制冷机,增大制冷机的驱动压比.由于声学压力波放大器内的压力幅值通常较大,流动速度也非常大,所以用线性热声理论难以对其进行准确的计算.本文通过对线性热声理论进行修正,获得了热声压力波放大器内湍流流动的修正方法,并对该修正方法进行了实验验证.研究结果表明,通过修正后的理论模型可以对热声压力波放大器进行较为准确的计算.该计算模型预计在其它的一些交变流动系统中也具有一定的适用性. 相似文献
2.
3.
4.
热声发动机作为一种完全没有运动部件的能量转化和传输机械具有广阔的应用前景.为了提高热声发动机的驱动性能,本文采用变负载法对热声发动机性能的影响因素进行了实验研究.实验结果表明,负载的阻力和容抗对热声发动机的加热温度、压比和声功引出有重要影响.同时,实验中还发现了能够使热声发动机瞬时消振和起振的实验方法,将极大方便对热声发动机的开关控制. 相似文献
5.
6.
7.
本文基于包含流动和传热两个方面的电路类比理论,针对一具有环路结构的气液相变热声发动机系统进行了模拟计算和分析。重点讨论了排出器、动力活塞、反馈管以及负载液柱的直径和长度对于系统谐振频率和换热器驱动温度梯度的影响。结果显示,该气液相变热声发动机的谐振频率较低(小于1 Hz),排出器和动力活塞的直径,以及反馈管的直径和长度对于谐振频率的影响较大;气液相变热声发动机所需驱动温度梯度比通常气体工质热声发动机小一到两个数量级,各主要部件的直径对气液相变热声发动机所需驱动温度梯度的影响比长度对其影响更为显著。 相似文献
8.
9.
10.
11.
LCC谐振变换器是电除尘高频高压电源的核心器件,十分适用于高压大功率场合,针对连续模式应用于电除尘高频高压电源的不足,采用LCC谐振变换器断续模式进行优化设计。分析了带RC负载的LCC谐振变换器断续模式(简称DCM)的工作原理及拓扑结构,采用状态空间法推导了其数学模型,研究并建立了新颖的LCC谐振变换器断续模式下的损耗模型。在此基础上提出了一种基于遗传粒子群算法的LCC谐振变换器优化设计方法,该方法直观并且准确,实现了软开关技术,提高了电源的工作效率。并在现场通过一台72KV/85KW的电除尘高频高压电源样机验证了本文的正确性。 相似文献
12.
13.
Suekane T. Yoshikawa K. Kabashima S. 《IEEE transactions on plasma science. IEEE Nuclear and Plasma Sciences Society》1995,23(1):97-102
Two dimensional calculations were carried out to clarify the behavior of boundary layer and its effects on performance of closed cycle MHD (CCMHD) generator and to investigate the relation between enthalpy extraction ratio and adiabatic efficiency. Calculation results suggest that the large Lorentz force causes propagation and separation of boundary layer where reverse current flows, because of small electromotive force. For large load resistance boundary layer becomes very thick and the eddy current arises in broad region. The push work of working gas against Lorentz force is effectively converted into electric energy under the condition at which the Lorentz force decelerates the working gas to Mach number in the range between 1.0 and 1.5 in this case of the generator. Stagnation pressure loss increases with load resistance until enthalpy extraction ratio takes maximum value. The entropy production due to Joule heating and viscosity increases with load resistance. The difference between the load resistances for which the enthalpy extraction ratio and the adiabatic efficiency take maximum value can be explained with the entropy production of Joule heating and viscosity 相似文献
14.
采用射频反应磁控溅射方法,在Si(001)基片上制备了具有高c轴择优取向的ZnO薄膜.利用原子力显微镜、X射线衍射、透射电子显微镜和透射光谱分析技术,对不同工作气压下合成的ZnO薄膜的表面形貌、微观结构和光学性能进行表征,研究了工作气压对ZnO薄膜的结晶性能以及生长行为的影响.研究结果显示:对于Ar/O2流量比例接近1∶1的固定比值下,ZnO薄膜的生长行为主要取决于成膜空间中氧的密度,临界工作气压介于0.5—1.0 Pa之间.当工作气压小于临界值时,ZnO薄膜的成核密度较高,且随工作气压的变化明显,ZnO的生长行为受控于氧的密度,属于氧支配的薄膜生长;当工作气压大于临界值以后,ZnO薄膜的成核密度基本保持不变,Zn原子的数量决定薄膜的生长速率;在0.1—5.0 Pa的工作气压范围内,均可获得高度c轴取向的ZnO薄膜,但工作气压的变化改变着ZnO晶粒之间的界面特征和取向关系.随着工作气压的增加,ZnO晶粒之间的界面失配缺陷减少,但平面织构特征逐渐消失,三叉晶界的空洞逐渐扩大,薄膜的密度下降,折射率减小.
关键词:
ZnO薄膜
磁控溅射
表面形貌
微观结构
光学性能 相似文献
15.
The coupling between rigid-walled modes of a rectangular cavity (RC modes) is used to obtain the shapes and resonance frequencies of rigid-walled modes of a trapezoidal cavity (TC modes) with an inclined rigid wall. A method is established to identify the TC modes, where the modes can be defined to evolve from individual RC modes. The wall inclination generates two coupling mechanisms, namely, the local coupling where the RC modes couple at the inclined wall, and the global coupling where the RC modes couple throughout the trapezoidal volume. The latter arises from the nonorthogonality of the RC modes in the trapezoidal volume. Both couplings are selective that only RC modes with the same number of nodes in the direction perpendicular to the inclination are coupled to each other. For small inclinations, each TC mode possesses the distorted shape of the RC mode that evolves it. When the inclination is increased, the TC-mode shape becomes complicated and unrecognizable, and extrema can also exist in the resonance frequency of the TC mode. These behaviors are determined by the behaviors of the local and global couplings of the RC mode. This paper provides an understanding of how the free vibration characteristics of TC modes change with the inclination and what determines these changes. 相似文献
16.
为准确、快速获取拉索结构索力,该文提出利用结构近场固定位置辐射声压信号对拉索进行索力测试的方法。基于动力学理论推导出结构振动加速度响应与其近场辐射声压响应的线性比例关系,并根据希尔伯特-黄变换推导了声压响应信号与结构频率的关系。对单根拉索依次施加3种不同工况的初始张拉力,并对结构中心表面处施加一瞬时脉冲力,使拉索受迫振动发声,通过对结构近场范围内拉索振动辐射声压进行测量,进而获得不同工况下不同位置声压响应信号,并探讨了在有高斯噪声干扰情况下通过希尔伯特-黄变换方法获取拉索固有频率的可靠性。数值模拟分析验证了该方法能较为准确地得到拉索固有频率并利用索力计算实用公式有效地计算出索力值,为实际工程中拉索索力测试提供了一种新的简单有效的方法。 相似文献
17.
介绍了液相斯特林机用液相工质的性质。并以工质 RC31 8作为算例 ,介绍了液相工质的热力学性质和热物理性质的数值计算 ,计算结果与已有的实验结果吻合较好。该文也将是研究和开发低品位热源液相热声热机的重要参考。 相似文献
18.
M. A. Ilgamov 《Doklady Physics》2017,62(10):461-464
The distributed lateral load on a plate located in a gas medium has been determined. The difference in the gas pressures of the plate surfaces results in a pressure drop and a lateral force, which depends on the middle surface curvature. It is shown that both these components of the lateral force must be taken into account in the general case. The influence of the second load component is small at a small ratio of the average pressure to the elastic modulus of the plate material and at a large relative thickness of the plate. At a small relative plate thickness and a large ratio of the average pressure of the medium to the elastic modulus of the plate material, the influence of the second component of the lateral load on the bending becomes significant. Cases of both linear and nonlinear plate bending are considered. 相似文献
19.
将六面顶压机立方压腔内置入电路,采用原位电阻测量确定Bi,Tl,Ba相变的方法,标定了压腔内不同位置的压力(强).通过标定立方压腔顶锤表面的压力并结合计算,分别得到了外部加载与压腔密封边受力以及合成腔体受力的对应关系.实验分析结果表明,随着外部加载的增加,当腔体压力达到5 GPa时,消耗在压腔密封边上的加载急剧上升,消耗在合成腔体的加载趋于不变,从而导致立方压腔压力达到上限.利用实验结果,分析了立方压腔在高压下的受力状态,解释了立方压腔的压力难以超过7 GPa的原因.结合立方压腔的几何结构,通过理论分析,提出了采用高体弹模量的物质作为传压介质,同时采用低体弹模量的物质作为密封边提高立方压腔压力上限的可行方案.通过定量标定叶腊石压腔轴向的压力梯度,给出了压腔内沿对称轴不同位置压力值的计算方法,此方法可为高压实验提供更精确的压力数据. 相似文献