传导冷却半导体激光阵列温度均匀化研究

高功率半导体激光器阵列已经广泛应用于许多领域。Smile效应是由高功率半导体激光器阵列（巴条）本身在封装过程中与热沉之间热膨胀系数（CTE）失配导致的热应力造成的。各个发光点在横向上不在一条直线上,从而导致半导体激光阵列整体发光弯曲。较大的Smile值可以引起光束质量降低、造成光束耦合和光束整形困难。为了降低热串扰实现巴条温度均匀化,我们在传统CS热沉的基础上,引入高热导率铜基石墨烯（GCF）与孔状结构,对CS被动式制冷半导体巴条热应力分布不均导致的Smile效应进行了数值模拟与仿真分析。在热功率为60 W的条件下,一方面,当仅有GCF材料,并且其长度为8 mm时,温差从最初的7.94 ℃降低到3.65 ℃;另一方面,在合理的温升范围内,当GCF的长度为8 mm时,结合增加热沉热阻的孔状结构时,温差进一步降低到3.18 ℃。     

高功率半导体激光器低温特性分析

研制了一套微通道封装结构半导体激光器的低温测试表征系统,实现了对高功率半导体激光器在-60℃～0℃低温范围内的输出功率、电光转换效率和光谱等关键参数稳定可靠的测试表征.采用计算流体力学及数值传热学方法,模拟了无水乙醇、三氯乙烯以及五氟丙烷三种载冷剂的散热性能.模拟结果表明,压降均为0.47bar时,采用无水乙醇作载冷剂的器件具有最低的热阻(热阻为0.73K/W)和最好的温度均匀性(中心和边缘发光单元温差为1.45℃).低温测试表征系统采用无水乙醇作为载冷剂,最大可实现0.5L/min的载冷液体流量,最多能容纳5个半导体激光器巴条同时工作.基于该低温测试表征系统,对微通道封装结构976nm半导体激光器巴条在6%占空比下的低温特性进行了研究.测试结果表明,载冷剂温度由0℃下降到-60℃,半导体激光器的输出功率由388.37 W提升到458.37 W,功率提升比为18.02%;电光转换效率由60.99%提升到67.25%,效率提升幅度为6.26%;中心波长由969.68nm蓝移到954.05nm.器件开启电压增加0.04V,阈值电流降低3.93A,串联电阻增加0.18mΩ,外微分量子效率提高11.84%.分析表明,阈值电流的减小及外微分量子效率的提高,是促使半导体激光器在低温下功率、效率提升的主要因素.研究表明,采用液体微通道冷却的低温工作方式,是实现半导体激光器高输出功率、高电光转换效率的一种有效手段.     

大功率半导体激光器叠层无氧铜微通道热沉

建立了叠层无氧铜微通道热沉的散热模型,通过理论计算和近似分析,优化了微通道热沉的结构参数;在t=200μm, ωc=60μm, ωf=100μm,p=2. 02×106 Pa时,可获得最小热沉热阻Rthm =4. 205×10-3 K·cm2 /W。根据优化结果,考虑微通道取向对液压降的影响,设计了一种新型大功率半导体激光器叠阵用五层结构叠层无氧铜微通道热沉,并结合实际工艺制备了无氧铜微通道热沉。在实际工作中,优化结果往往要跟实际工艺相结合,如优化所得的水压降为 2 02×106 Pa,这在实际工艺中较难实现。但在热沉实际工作的水压降条件下,热阻为 4. 982×10-3 K·cm2 /W,它能满足高功率激光器叠阵的需要。     

C-mount封装激光器热特性分析与热沉结构优化研究

为了降低单管半导体激光器的结温、提高器件的散热效果,基于C-mount热沉的热特性分析提出了一种优化的台阶热沉结构,研究了单管激光器结温和腔面侧向温度分布曲线的影响。在热沉温度298 K和连续输出功率10 W的条件下,腔长为1.5 mm的典型C-mount封装结构激光器的结温为343.6 K,热阻为4.6 K/W。通过在典型C-mount热沉中引入台阶结构,使封装激光器的结温降低为333.8 K,热阻减小到3.5 K/W。计算表明,其输出功率可提高近20%。     

岐管式微通道冷却热沉的三维数值优化

微尺度传热是近几年来发展起来的一种重要传热技术,广泛应用于高集成度的电子器件的冷却。大功率半导体激光器的热沉积是限制其性能发挥和功率进一步提高的瓶颈。本文研究的热沉用于冷却一种以半导体激光条阵列为泵浦的大功率激光器,其10 mm×1 mm半导体激光条表面的热流密度高达400 W／cm2。本文对以无氧铜为材料、以水为冷却介质的微通道热沉的结构尺寸进行了优化设计。结果表明,热沉结构对热阻、泵功、半导体激光条表面温度分布有重要影响,其中微通道进出口宽度对泵功的影响最大。     

基于沸腾-空化耦合效应的微通道线阵LD用热沉

 针对大功率LD的冷却需求,基于沸腾-空化耦合效应,研制了一种微通道相变热沉,封装腔长1.5 mm的LD线阵。依据加工条件确定通道宽度、深度以及间距,采用2维数值模型估算了通道长度,热沉材料采用无氧铜,多层叠焊,外形尺寸为20 mm×12 mm×1.6 mm。实验测试了连续功率LD输出0～100 W时的电 光转换效率以及电流 输出功率等特性,冷却工质采用R134a,磁驱齿轮泵电机转速50 r/s时热沉热阻为0.3 ℃/W。结果显示微通道相变热沉具有良好的散热能力,能够满足大功率LD的散热要求。     

高功率半导体激光器微通道热沉的方案设计

 对用于高功率半导体激光器的叠片式微通道热沉进行方案设计,利用计算流体力学和数值传热学对各种方案进行数值仿真,研究了微通道的特征尺寸和流量等因素对冷却效果和流动阻力特性的影响,一般情况下,减小微通道的特征尺寸和增加冷却水的流量可以降低传热热阻,但增加了流动压力损失;另外对金刚石热扩散片（次热沉）的效果也进行了数值计算,计算结果表明:金刚石热扩散片在该类型问题中降低温度作用明显。     

平行细小槽道热沉的综合性能实验测试

为考察基于矩形平行细小槽道的压降及传热的综合性能,实验测试了去离子水流过三种不同截面尺寸的平行细小槽道热沉的流动与传热特性,槽道截面尺寸分别为1mm×1mm、0.5mm×1mm、0.5mm×1.2mm,表面热流密度为5.6~33.3W/cm2,工质流量为0.3~5L/min。实验测量了压降及对流换热系数随流量变化关系;综合分析了三种热沉的压降-温度随流量变化规律;得出了细小槽道热沉在给定流量范围内,表面温度为70℃时的极限热流密度。实验结果表明:随着流量增加,表面温度与压降呈相反变化趋势,存在一个最佳工况点,该工况点处的工质流量随热流密度增加而增大;文中所设计的热沉在工质流量为1.3~4.75L/min,表面温度控制在70℃时所能承受的极限热流密度为70W/cm2,此时压降约为170kPa。     

多孔细径微肋管内CO2流动蒸发换热特性的研究

对亚临界二氧化碳在带有微肋的微细通道内的蒸发换热特性进行了实验研究.实验段为长0.6 m,内径1.7 mm的八孔带0.16 mm高微肋的铝制扁管.实验中参数的变化为:蒸发温度1～15 ℃,质量流速100～300 kg/m2s,热流密度1.67～8.33 kW/m2,干度0.1～0.9.实验结果表明,二氧化碳在带有微肋的微细通道中的蒸发换热系数高于其在光滑微细通道内的换热.二氧化碳的流动蒸发换热系数主要受热流密度和蒸发温度的影响,基本上是换热系数随热流密度及蒸发温度的增加而增加,但同时临界干度前移及滞后,而质量流速对换热系数的影响较弱;压力损失随质量流速和热流密度的增加以及蒸发温度的降低而增加.     

激光二极管高效铜微通道冷却器设计

 通过对铜微通道冷却器的散热分析，设计出５层结构的模块式铜微通道冷却器。采用常规的线切割工艺加工，散热通道宽大约200μm，深300μm，各层间用真空钎焊的方法组装。该冷却器对于腔长06mm、宽10mm的线阵激光二极管芯片热阻为0.58℃/W。通过面阵激光二极管封装实验证明，该冷却器可用于10％占空比工作的面阵激光二极管封装。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.