Active temperature compensation design of sensor with fiber gratings

A technique for compensation of temperature effects in fiber grating sensors is reported. For strain sensors and other sensors related to strain such as electromagnetic sensors, a novel structure is designed, which uses two fiber Bragg gratings (FBGs) as strain differential sensor and has temperature effects cancelled. Using this technique, the stress sensitivity has been amplified and gets up to 0.226 nm/N, the total variation in wavelength difference within the range of 3-45 ℃ is 0.03 nm, 1/14 of the uncompensated FBG.The structure can be used in the temperature-insensitive static strain measurement and minor-vibration measurement.     

Multiwavelength fiber laser based on a photonic crystal fiber loop mirror with cooperative Rayleigh scattering

In this work, a multiwavelength fiber Raman laser based on a highly birefringent photonic crystal fiber loop mirror is presented. A laser resonator is formed when the Raman amplification with cooperative Rayleigh scattering in a dispersion-compensating fiber is used as a distributed mirror and combined with a photonic crystal fiber loop mirror filtering structure. Stable multiwavelength lasing at room temperature is achieved due to the low temperature sensitivity of the highly birefringent photonic crystal fiber.     

A fiber micro-vibration sensor based on single-mode fiber ring laser

A new micro-vibration sensor based on single-mode fiber ring laser is put forward. The Mach-Zehnder interferometric （MZI） detection technique is presented for interrogating laser frequency shift due to the measurand （piezoelectric transducer （PZT） is used to simulate the micro-vibration） induced laser cavity strain from both single- and multi-mode lasers. In the experiment, compared with multi-mode laser sensors, the single-mode laser sensor is proved to be a sensor with high resolution. When the PZT is driven by the analog signal （0.03 rad near 2 kHz）, the signal-to-noise ratio （SNR） of output signal from the single-mode laser sensor is close to 55 dB and the sensitivity of the sensor is about 5 ×10^-5 rad/Hz1/2.     

光纤Bragg光栅应变、温度交叉敏感问题的研究

解决应变和温度的交叉敏感,实现应变和温度同时测量一直是光纤光栅传感器研究的关键问题。从应变和温度交叉敏感的物理机制出发,较为全面地介绍了几种主要解决方案：双波长矩阵法、2个包层直径不同的FBG法、啁啾光栅法等。并且基于双波长矩阵法,提出了一种基于管式弹性应变敏感元件的光纤光栅传感器结构,很好地实现了温度150℃,压力20MPa的同时区分测量,其温度灵敏度为0.02nm/℃。解决了温度和应变同时区分测量这一技术难题。     

Intensity-modulated fiber Bragg grating sensor system based on radio-frequency signal measurement

An intensity-modulated, fiber Bragg grating (FBG) sensor system based on radio-frequency (RF) signal measurement is presented. The RF signal is generated at a photodetector by two modulated optical signals reflected from the sensing FBG and a reference FBG. Wavelength shift of the sensing FBG changes intensity of the RF signal through changing the delay between the two optical signals, with temperature effect being compensated automatically by the reference FBG. It also exhibits important features including potentially high-speed measurement, low cost, and adjustable sensitivity. In the experiment, strain measurement with a maximum sensitivity of -0.34 microV/micro epsilon has been achieved.     

基于封装光纤Bragg光栅传感器的混凝土应变监测试验研究

研究了光纤Bragg光栅封装工艺,提出并实现了两种封装光纤Bragg光栅传感器:工字型钢管封装光纤Bragg光栅应变传感器及钢管封装光纤Bragg温度传感器。研究了传感器的埋设工艺,采用金属丝固定法、钢管抽出法两种方法进行了埋设。将它们埋入到钢筋混凝土梁中,实现对混凝土的拉、压应变及温度的测量。结果显示,在试验梁弹性阶段,可以较为准确的监测混凝土应变。     

铜片封装光纤光栅传感器的应变和温度传感特性研究

提出了一种光纤光栅的铜片封装工艺，并通过实验和理论分析研究了光纤光栅的应变和温度传感特性.与裸光纤光栅的测试结果相比，铜片封装工艺基本不改变光纤光栅应变传感的灵敏度，但是温度灵敏度系数提高了2.78倍.经过铜片封装后的光纤光栅可以探测到的应变和温度分别为1 με和0.03℃，便于工程应用.     

Temperature-insensitive Mach-Zehnder interferometric strain sensor based on concatenating two waist-enlarged fiber tapers

A novel temperature-insensitive strain sensor,based on an in-line Mach-Zehnder interferometer,is fabricated by concatenating two waist-enlarged fiber tapers separated by a short piece of photonic crystal fiber. The interference spectrum of the proposed sensor is analyzed in detail.Experimental results demonstrate that this sensor has a strain sensitivity of.3.02 pm/μεand maintains the temperature insensitivity feature. The proposed sensor has great potential in diverse sensing applications due to its advantages,such as its compact size,low cost,and simple fabrication process.     

具有温度自校准功能的光纤折射率传感器

提出一种具有温度自校准功能的光纤折射率（RI）传感器,传感头结构由2段很短的多模光纤（MMF）之间夹熔一段对折射率不敏感的光纤布拉格光栅（FBG）构成,传感头总长度为14 mm,FBG可以为折射率测量提供良好的温度校准功能。实验结果证明,该传感器的折射率灵敏度为126 nm。其干涉光谱共振波长的温度灵敏度为35.09 pm/℃,用于温度校准的FBG的温度灵敏度为11.14 pm/℃。相比于普通的折射率传感器,这种具有温度自校准功能的折射率传感器具有良好的实用前景。     

光纤布拉格光栅激光器的传感应用

光纤激光器是一种光束质量好、信噪比高的光源。合理利用光纤激光器中布拉格光栅的传感特点能够制作出性能优良的高灵敏度传感器。光纤激光式传感器按结构基本可分为分布布拉格反射式光纤激光器以及分布反馈式光纤激光器两种。对这两类传感器进行介绍并对这些传感器的优缺点进行分析,最后展望其应用前景。     

A Raman laser intensity sensor induced by the cooperative Rayleigh scattering in a ring configuration

In this work, a laser sensor is described that uses the multipath interference produced inside a ring cavity to measure the power loss induced by a moving taper intensity sensor. The laser is created due to the virtual distributed mirror formed by the Rayleigh scattering produced in a dispersion compensating fiber when pumped by a Raman laser. Two laser peaks were formed, one of them is obtained by the Raman gain (1555 nm) inside the ring and the second is created by the combination of the Raman gain and the Rayleigh scattering (1565 nm). A taper sensor is used as displacement sensor and when the losses is applied in the taper the second laser peak is reduced and the first peak is maintained constant and can be used as reference level.     

Long-distance fiber Bragg grating sensor system with a high optical signal-to-noise ratio based on a tunable fiber ring laser configuration

A novel tunable fiber ring laser configuration with a combination of bidirectional Raman amplification and dual erbium-doped fiber (EDF) amplification is proposed for realizing high optical signal-to-noise ratio (SNR), long-distance, quasi-distributed fiber Bragg grating (FBG) sensing systems with large capacities and low cost. The hybrid Raman-EDF amplification configuration arranged in the ring laser can enhance the optical SNR of FBG sensor signals significantly owing to the good combination of the high gain of the erbium-doped fiber amplifier (EDFA) and the low noise of the Raman amplification. Such a sensing system can support a large number of FBG sensors because of the use of a tunable fiber Fabry-Perot filter located within the ring laser and spatial division multiplexing for expansion of sensor channels. Experimental results show that an excellent optical SNR of approximately 60 dB has been achieved for a 50 km transmission distance with a low Raman pump power of approximately 170 mW at a wavelength of 1455 nm and a low EDFA pump power of approximately 40 mW at a wavelength of 980 nm, which is the highest optical SNR achieved so far for a 50 km long FBG sensor system, to our knowledge.     

基于光纤微结构加工和敏感材料物理融合的光纤传感技术

将功能敏感材料与光纤在物理层面进行有机融合,充分发挥光纤传感器在结构集成、材料集成等方面的优势,将有望发展新型的光纤传感器件和系统.本文综述了飞秒激光光纤微加工技术分别在标准的单模光纤和光纤光栅上制备微结构,再结合敏感材料制备技术,实现在物理层面上光纤传感器材料和结构的集成和融合,探索实现新型高性能的光纤传感新技术.     

平面圆形膜片式光纤布拉格光栅温度补偿压强传感

报道了利用光纤布拉格光栅反射波谱带宽展宽技术实现温度补偿的压强传感新方案。结合平面圆形膜片应变调谐的特点,采用膜盒式结构,将光纤光栅中心对准平面圆形膜片零应变半径并沿径向粘贴,利用反射波谱带宽对应变敏感而对温度不敏感的特性解调压强,成功地实现了温度补偿的压强传感测量。基于光谱分析仪0.05nm的光谱分辨力,实验测得带宽随压强响应灵敏度为0.34nm/MPa,压强精度为±0.15MPa,压强测量范围为0~7.5MPa。实验结果与理论分析基本一致。     

On the possible use of optical fiber Bragg gratings as strain sensors for geodynamical monitoring

Optical fiber sensors can be used to measure many different parameters including strain, temperature, pressure, displacement, electrical field, refractive index, rotation, position and vibrations. Among a variety of fiber sensors, fiber Bragg gratings (FBG) have numerous advantages over other optical fiber sensors. One of the major advantages of this type of sensors is attributed to wavelength-encoded information given by the Bragg grating. Since the wavelength is an absolute parameter, signal from FBG may be processed such that its information remains immune to power fluctuations along the optical path. This inherent characteristic makes the FBG sensors very attractive for application in harsh environments, “smart structures” and on-site measurements.This paper reviews the achievements about the FBG as a strain and temperature sensor and describes the potential applications of FBG sensors for applications in the field of geophysics and its expected development in the near future. The applications could include: rock deformation, fiber-optic geophone, optical based seismograph, vertical seismic profiling and structural monitoring of civil structures. Different techniques to detect strains and various applications will be reviewed and discussed. The problem of temperature–strain cross sensitivity, that is particularly difficult to eliminate, is addressed and approaches to overcome it are discussed.     

光纤光栅传感器交叉敏感问题研究

交叉敏感问题是光纤光栅传感器在实际应用中需面对的一个关键问题。从光纤Bragg光栅的传感理论出发，分析了光纤光栅在同时测量应变和温度时引起交叉敏感的物理机理，建立了带有温度-应变交叉灵敏度系数的光纤Bragg光栅反射波长方程。利用双波长矩阵算法针对上述建立的光纤光栅方程进行了误差分析，获取了在交叉敏感情况下温度和应变的相对误差曲线图。结合相对误差表达式和曲线图分析讨论了交叉敏感对测量带来的影响。结果表明在温度和应力测量中随着测量温度或者应变变化量的增大，忽略交叉敏感项而带来的测量误差越来越明显。     

Random distributed feedback Raman fiber laser operating in a 1.2 μm wavelength range

The random distributed feedback fiber laser operating via the stimulated Raman scattering and random distributed feedback based on the Rayleigh scattering is demonstrated in the 1.2 μm frequency band. The RDFB fiber laser generates at 1174 nm up to 2.4 W of output power with corresponding slope efficiency more than 30%. The output radiation has the spectral shape similar to the conventional Raman fiber lasers and spectral width less than 1.7 nm.     

Long-distance fiber sensor system based on the second-order Raman pump and amplification

We demonstrate a novel technique to realize a long-distance fiber sensor system based on the second-order Raman pump and amplification. With the second-order Raman pump and amplification, a gain spectrum around 1582-nm is achieved. It serves as not only the optical source for the remote fiber sensor but also the filter to intensity modulated the wavelength shift of the fiber sensor. A long-distance fiber strain sensor system is demonstrated by adopting a fiber Fabry?CPérot sensor. Experimental results show that the wavelength shift of the sensor in response to the strain is simultaneously intensity modulated by the steep slope with a high sensitivity, while it is temperature insensitive. With the side gain spectrum served as a quasi-linear filter, the sensor can also be quasi-linearly intensity-modulated.     

基于掺铒光纤/喇曼混合放大的光纤激光器布喇格光栅传感系统

提出了一种提高长距离光纤布喇格光栅信噪比以进行准分布测量的新方法.该方法基于掺铒光纤/喇曼混合放大的光纤激光器结构,掺铒光纤和滤波器构成的环形结构产生激光作为光源,喇曼光纤放大器对布喇格光栅信号进行低噪音的双向放大,置于远处的掺铒光纤利用剩余的泵浦功率产生自发辐射光和放大传感信号,为远处掺铒光纤之后的布喇格光栅传感器提供信号光以及补偿由于长距离传输造成的光纤损耗.实验显示,与使用宽带光源的传感方式相比,系统的性能得到显著提高,仅使用小功率泵浦,分布在50 km光纤上的FBG均获得了超过58 dB的优良信噪比.     

Fiber Bragg grating strain sensor based on fiber laser

A study on fiber Bragg grating (FBG) strain sensor, based on erbium-doped fiber (EDF) laser, is presented. A strain-sensing element, FBG, also acts as the lasing wavelength selecting component. When strain is applied on the FBG, the laser cavity loss changes, leading to a modification of the laser transient. Strain measurements are obtained in the time domain by simply measuring the EDF laser build-up time. Relative variation in the build-up time of up to 190%, for a strain range from 0 με to 2350 με, is achieved with a resolution corresponding to a strain of better than 2.35 με. This study demonstrates a novel fiber sensor concept and the technical feasibility to develop fiber strain measurement.