Structural and PL properties of Cu-doped ZnO films

Cu-doped ZnO films with hexagonal wurtzite structure were deposited on silicon (1 1 1) substrates by radio frequency (RF) sputtering technique. An ultraviolet (UV) peak at ∼380 nm and a blue band centered at ∼430 nm were observed in the room temperature photoluminescent (PL) spectra. The UV emission peak was from the exciton transition. The blue emission band was assigned to the Zn interstitial (Zn_i) and Zn vacancy (V_Zn) level transition. A strong blue peak (∼435 nm) was observed in the PL spectra when the α_Cu (the area ratio of Cu-chips to the Zn target) was 1.5% at 100 W, and ZnO films had c-axis preferred orientation and smaller lattice mismatch. The influence of α_Cu and the sputtering power on the blue band was investigated.     

Pulsed laser deposited ZnO/ZnO:Li multilayer for blue light emitting diodes

Thin films of ZnO, Li doped ZnO (ZLO) and multilayer of ZnO and ZLO (ZnO/ZLO) were grown on silicon and corning glass substrates by pulsed laser deposition technique. Single phase formation and the crystalline qualities of the films were analyzed by X-ray diffraction and Li composition in the film was investigated to be 15 wt% by X-ray photoelectron spectroscopy. Raman spectrum reveals the hexagonal wurtzite structure of ZnO, ZLO and ZnO/ZLO multilayer and confirms the single phase formation. Films grown on corning glass shows more than 80% transmittance in the visible region and the optical band gaps were calculated to be 3.245, 3.26 and 3.22 eV for ZnO, ZLO and ZnO/ZLO, respectively. An efficient blue emission was observed in all films which were grown on silicon (1 0 0) substrate by photoluminescence (PL). PL measurements at different temperatures reveal that the PL emission intensity of ZnO/ZLO multilayer was weakly dependent on temperature as compared to the single layers of ZnO and ZLO and the wavelength of emission was independent of temperature. Our results indicate that ZnO/ZLO multilayer can be used for the fabrication of blue light emitting diodes.     

Irreversible quenching of luminescence in porous silicon

The influence of applied voltage on photoluminescence (PL) in porous silicon was studied. A strong PL band around 680 nm was observed when excited by a 300 nm ultraviolet light with no voltage applied, but upon increasing the bias voltage, a strong and progressive decrease of the PL intensity was observed leading finally to a complete quenching of the emitted light at 1.80 V. The peak position of the emission appears to be stable. This effect is completely irreversible, and the spectra depend on the increased voltage to the sample and corresponding temperature increase. Nonradiative recombination resulting from the thermal oxidation was suggested to be responsible for the quenching.     

Infrared luminescence from spark-processed silicon

The infrared (IR) photoluminescence (PL) emission of spark-processed silicon (sp-Si) was investigated. A broad and strong room temperature PL peak in the 945 nm (1.31 eV) spectral range was observed when sp-Si was excited with an argon laser. This peak is different from the PL commonly reported for anodically etched porous silicon and other silicon-based materials. The PL intensity increases substantially after annealing sp-Si between 350 and 500 °C in air after which it decreases again. The PL wavelength is observed to peak at 1010 nm by annealing sp-Si near 450 °C. It was further found that the most efficient PL occurs for a Si/O ratio of 0.3, for a small spark gap of about 1 mm, and for spark-processing times in the 15-60 min range.A model for the IR PL is proposed which mirrors that for visible PL. Specifically, it is proposed that the electrons which have been pumped by the laser from the ground state into a broad quasi-absorption band (or closely spaced absorption lines between 1.7 and 2.3 eV) revert back to lower IR levels at 1.31 eV by a non-radiative transition from where they revert radiatively to the ground state by emitting the observed 945 nm light.     

Strong violet luminescence from ZnO nanocrystals grown by the low-temperature chemical solution deposition

The luminescence properties of zinc oxide (ZnO) nanocrystals grown from solution are reported. The ZnO nanocrystals were characterized by scanning electron microscopy, X-ray diffraction, cathodo- and photoluminescence (PL) spectroscopy. The ZnO nanocrystals have the same regular cone form with the average sizes of 100-500 nm. Apart from the near-band-edge emission around 381 nm and a weak yellow-orange band around 560-580 nm at 300 K, the PL spectra of the as-prepared ZnO nanocrystals under high-power laser excitation also showed a strong defect-induced violet emission peak in the range of 400 nm. The violet band intensity exhibits superlinear excitation power dependence while the UV emission intensity is saturated at high excitation laser power. With temperature raising the violet peak redshifts and its intensity increases displaying unconventional negative thermal quenching behavior, whereas intensity of the UV and yellow-orange bands decreases. The origin of the observed emission bands is discussed.     

Laser on porous silicon after oxidation by irradiation and annealing

Stimulated emission has been observed from oxide structure of silicon when optically excited by 514 nm laser. The photoluminescence (PL) pulse has a Lorentzian shape with a full width at half maximum (FWHM) of 0.5-0.6 nm. The twin peaks at 694 nm and 692 nm are dominated by stimulated emission which can be demonstrated by its threshold behavior and transition from sub-threshold to linear evolution in light emission. The gain coefficient from the evolution of the peak-emission intensity as a function of the optically pumped sample length has been measured. The oxide structure was fabricated by laser irradiation and annealing treatment on silicon. A model for explaining the stimulated emission has been proposed in which the trap states of the interface between oxide of silicon and porous nanocrystal play an important role.     

Annealing and amorphous silicon passivation of porous silicon with blue light emission

The photoluminescence (PL) of the annealed and amorphous silicon passivated porous silicon with blue emission has been investigated. The N-type and P-type porous silicon fabricated by electrochemical etching was annealed in the temperature range of 700-900 °C, and was coated with amorphous silicon formed in a plasma-enhanced chemical vapor deposition (PECVD) process. After annealing, the variation of PL intensity of N-type porous silicon was different from that of P-type porous silicon, depending on their structure. It was also found that during annealing at 900 °C, the coated amorphous silicon crystallized into polycrystalline silicon, which passivated the irradiative centers on the surface of porous silicon so as to increase the intensity of the blue emission.     

1.54 μm emission mechanism of Er-doped zinc oxide thin films

Zinc oxide (ZnO) and Er-doped zinc oxide (ZnO:Er) thin films were formed by pulsed laser deposition, and characterized by photoluminescence (PL) and X-ray diffraction (XRD) in order to clarify the 1.54 μm emission mechanism in the ZnO:Er films. Er ions were excited indirectly by the 325 nm line of a He-Cd laser, and the comparison of the ultraviolet to infrared PL data of ZnO and ZnO:Er films showed that the 1.54 μm emission of Er³⁺ in ZnO:Er film appears at the expense of the band edge emission and the defect emission of ZnO. The crystallinity of the films was varied with the substrate temperature and post-annealing, and it was found that the intensity of the 1.54 μm emission is strongly related with the crystallinity of the films. There are three processes leading to the 1.54 μm emission; absorption of excitation energy by the ZnO host, energy transfer from ZnO to Er ions, and radiative relaxation inside Er ions, and it is suggested that the crystallinity plays an important role in the first two processes.     

Effect of temperature on pulsed laser deposition of ZnO films

ZnO thin films have been deposited on Si(1 1 1) substrates at different substrate temperature by pulsed laser deposition (PLD) of ZnO target in oxygen atmosphere. An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as laser source. The influences of the deposition temperature on the thickness, crystallinity, surface morphology and optical properties of ZnO films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), selected area electron diffraction (SAED), photoluminescence (PL) spectrum and infrared spectrum. The results show that in our experimental conditions, the ZnO thin films deposited at 400 °C have the best surface morphology and crystalline quality. And the PL spectrum with the strongest ultraviolet (UV) peak and blue peak is observed in this condition.     

Enhanced photoluminescence of Ar implanted sapphire before and after annealing

In this paper, we studied the changes in the photoluminescence spectra of the Ar⁺ ion implanted mono-crystalline sapphire annealed at different atmospheres and different temperatures. Single crystals of sapphire (Al₂O₃) with the (1 0 1¯ 0) (m-samples) orientation were implanted at 623 K with 110 keV Ar⁺ ions to a fluence of 9.5×10¹⁶ ions/cm². Photoluminescence measurement of the as-implanted sample shows a new emission band at 506 nm, which is attributed to the production of interstitial Al atoms. The intensity of emission band at 506 nm first increased then decreased with increase in annealing temperature. For the same annealing temperature, the intensity of PL peak at 506 nm of the sample annealed in air was higher than the sample annealed in vacuum. The experimental results show that the intensity of the PL peak at 506 nm of Ar-implanted sapphire can be enhanced by subsequent annealing with an enhancement of nearly 20 times. The influence of thermal annealing of the Ar-implanted samples on the new 506 nm emission band was discussed.     

Structural and optical properties of nanocrystalline ZnO thin films synthesized by the citrate precursor route

Nanocrystalline zinc oxide (ZnO) thin films have been deposited by spin-coating polymeric precursors synthesized by the citrate precursor route using ethylene glycol and citric acid as chelating agents. The ZnO thin films were annealed in air at different temperatures for 10 min. The films were characterized by different structural and optical techniques, including X-ray diffraction (XRD), atomic force microscopy (AFM), optical transmission spectroscopy, and photoluminescence (PL). The thermal decomposition of polymeric precursor was studied by thermogravimetric analysis (TGA). XRD analysis with grazing incidence and rocking curves indicate that the ZnO films are polycrystalline with preferential orientation along the c-axis direction with a full-width at half-maximum (FWHM) of 0.31° for 600 °C-annealed samples. On annealing, the texturing in films increased along with a decrease in FWHM. AFM micrographs illustrate that the ZnO films are crack-free with well-dispersed homogeneous and uniformly distributed spherical morphology. The synthesized ZnO thin films have transparency >85% in the visible region exhibiting band edge at 375 nm, which becomes sharper with anneal. Room temperature PL spectra of these films show strong ultraviolet (UV) emission around 392 nm with an increase in intensity with annealing temperature, attributed to grain growth. Deconvolution of the PL spectra reveals that there is coupling of free excitons with higher orders of longitudinal optical (LO) phonon replicas leading to a broad asymmetric near-band-edge peak.     

Mechanism of intense blue photoluminescence in silica wires

The photoluminescence (PL) properties of our silica wires were investigated with PL, PL excitation and PL decay. A high brightness photoluminescence band at 2.8 eV with a shoulder around 3.0 eV was observed in our silica wires. Two PL excitation bands for the 2.8 eV emission were observed at 4.77 and 3.37 eV. The 3.37 eV excitation band is reported for the first time. The characteristic of the blue PL in our silica wires was different from that of the well-known 2.7 eV PL in bulk silica material, suggesting a negation of previous attribution of blue emission in silica nanowires. The mechanism of the PL was also discussed.     

Optical properties of alumina membranes prepared by anodic oxidation process

The luminescence property of anodic alumina membranes (AAMs) with ordered nanopore arrays prepared by electrochemically anodizing aluminum in oxalic acid solutions have been investigated. Photoluminescence emission (PL) measurement shows that a blue PL band occurs in the wavelength ranges of 300-600 nm. The PL intensity and peak position of AAMs depend markedly on the excitation wavelength. A new peak located at 518 nm can be observed under a monitoring wavelength at 429 nm in the photoluminescence excitation (PLE) spectra. Convincing evidences have been presented that the PLE would be associated with the residual aluminum ions in the membrane. The PLE and PL of AAMs, as a function of anodizing times, have been discussed. It is found that the oxalic impurities incorporated in the AAMs would have important influences on the optical properties of AAMs in the initial stage of anodization. The PL and PLE spectra obtained show that there are three optical centers, of which the first is originated from the F⁺ centers in AAMs, the second is correlated with the oxalic impurities incorporated in the AAMs, and the third is associated with the excess aluminum ions in the membrane.     

Luminescence of dense, octahedral structured crystalline silicon dioxide (stishovite)

It is obtained that, as grown, non-irradiated stishovite single crystals possess a luminescence center. Three excimer pulsed lasers (KrF, 248 nm; ArF, 193 nm; F₂, 157 nm) were used for photoluminescence (PL) excitation. Two PL bands were observed. One, in UV range with the maximum at 4.7±0.1 eV with FWHM equal to 0.95±0.1 eV, mainly is seen under ArF laser. Another, in blue range with the maximum at 3±0.2 eV with FWHM equal to 0.8±0.2 eV, is seen under all three lasers. The UV band main fast component of decay is with time constant τ=1.2±0.1 ns for the range of temperatures 16-150 K. The blue band decay possesses fast and slow components. The fast component of the blue band decay is about 1.2 ns. The slow component of the blue band well corresponds to exponent with time constant equal to 17±1 μs within the temperature range 16-200 K. deviations from exponential decay were observed as well and explained by influence of nearest interstitial OH groups on the luminescence center. The UV band was not detected for F₂ laser excitation. For the case of KrF laser only a structure less tail up to 4.6 eV was detected. Both the UV and the blue bands were also found in recombination process with two components having characteristic time about 1 and 60 μs. For blue band recombination luminescence decay is lasting to ms range of time with power law decay ∼t⁻¹.For the case of X-ray excitation the luminescence intensity exhibits strong drop down above 100 K. such an effect does not take place in the case of photoexcitation with lasers. The activation energies for both cases are different as well. Average value of that is 0.03±0.01 eV for the case of X-ray luminescence and it is 0.15±0.05 eV for the case of PL. So, the processes of thermal quenching are different for these kinds of excitation and, probably, are related to interaction of the luminescence center with OH groups.Stishovite crystal irradiated with pulses of electron beam (270 kV, 200 A, 10 ns) demonstrates a decrease of luminescence intensity excited with X-ray. So, irradiation with electron beam shows on destruction of luminescent defects.The nature of luminescence excited in the transparency range of stishovite is ascribed to a defect existing in the crystal after growth. Similarity of the stishovite luminescence with that of oxygen deficient silica glass and induced by radiation luminescence of α-quartz crystal presumes similar nature of centers in those materials.     

Aligned growth of ZnO nanowires by NAPLD and their optical characterizations

Not only vertically aligned ZnO nanowires but also horizontally aligned ZnO nanowires have been successfully grown on the annealed (0 0 0 1) c-cut and (1 1 2 0) a-cut sapphire substrates, respectively using catalyst-free nanoparticle-assisted pulsed-laser ablation deposition (NAPLD). The as-synthesized ZnO nanowires exhibit an ultraviolet emission at around 390 nm and the absent green emission under room temperature. The single ZnO nanowire was collected in the electrode gap by dielectrophoresis (DEP). Under the optical pumping, the single ZnO nanowire exhibited UV emission at around 390 nm with several sharp peaks whose energy spacings are almost constant, which greatly differs from the broad UV emission of the film with many nanowires, suggesting ZnO nanowires as candidates for laser media. The single ZnO nanowire showed polarized photoluminescence (PL). The as-synthesized ZnO nanowires could find many interesting applications in short-wavelength light-emitting diode (LED), laser diode and gas sensor.     

Microstructure and blue photoluminescence enhancement of silicon nanoporous pillar array embedded in ferroelectric barium strontium titanate

A silicon nanoporous pillar array (Si-NPA) with micrometer/nanometer hierarchical structure was fabricated by hydrothermal etching, followed by spin-coating barium strontium titanate (BST) on Si-NPA substrate. The photoluminescence (PL) spectra of the Si-NPA and BST/Si-NPA thin film were investigated. The emission band of freshly prepared Si-NPA located at 630 nm, and a blueshift at 425 nm as well as degradation in intensity after annealing at 600 °C for 1 h was observed, which might be explained by a quantum confinement effect model. BST ferroelectric material provided a static-electric field and induced the excited carriers in Si-NPA to migrate toward the opposite direction and recombine in an interfacial oxide layer. Therefore, BST enhanced blue emission of Si-NPA as well as passivated Si-NPA.     

Preparation and luminescent characteristic of Li3NbO4 nanophosphor

Synthesis and luminescence properties of Li₃NbO₄ oxides by the sol-gel process were investigated. The products were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy and absorption spectra. The PL spectra excited at 247 nm have a broad and strong blue emission band maximum at 376 nm, corresponding to the self-activated luminescence of the niobate octahedra group [NbO₆]⁷⁻. The optical absorption spectra of the samples sintered at temperatures of 600 and 700 °C exhibited the band-gap energies of 4.0 and 4.08 eV.     

Photoluminescence from ZnO-SiO2 opals with different sphere diameters and thicknesses

We systematically investigated the photoluminescence (PL) and transmittance characteristics of ZnO-SiO₂ opals with varied positions of the stop-band and film thicknesses. An improved ultraviolet (UV) luminescence was observed from ZnO-SiO₂ composites over pure ZnO nanocrystals under 325 nm He-Cd laser excitation at room temperature. The UV PL of ZnO nanocrystals in SiO₂ opals with stop-bands center of 410 nm is sensitive to the thickness of opal films, and the UV PL intensity increases with the film thickness increasing. The PL spectra of ZnO nanocrystals in SiO₂ opals with stop-bands center of 570 nm show a suppression of the weak visible band. The experimental results are discussed based on the scattering and/or absorbance in opal crystals.     

β-Na(Y1.5Na0.5)F6:Tm—A blue upconversion phosphor

A luminescent material β-Na(Y_1.5Na_0.5)F₆ doped with Tm³⁺ was synthesized by a solid-state reaction method for a steady phosphor of blue upconversion. Under the 671 nm laser excitation, the green emission band of 511 nm due to the ¹D₂→³H₅ transition is obtained for the first time, while the ultraviolet emission band is also observed at 368 nm, associated with the ¹D₂→³H₆ transition. Especially, a wide band of blue emissions is obtained at the wavelength region of 440-490 nm, originated mainly from the ¹D₂→³F₄ (450 nm) and ¹G₄→³H₆ (471-487 nm) transitions, which have potential application in tunable solid-state blue laser of Tm³⁺. The upconversion mechanism is explored in terms of the energy-level structures of Tm³⁺ ion and the power dependence of upconverted emission intensity, which is believed to be performed by excited-state absorption.     

Preparation and characterization of Mg-doped ZnO thin films by sol-gel method

Undoped and Mg-doped ZnO thin films were deposited on Si(1 0 0) and quartz substrates by the sol-gel method. The thin films were annealed at 873 K for 60 min. Microstructure, surface topography and optical properties of the thin films have been measured by X-ray diffraction (XRD), atomic force microscope (AFM), UV-vis spectrophotometer, and fluorophotometer (FL), respectively. The XRD results show that the polycrystalline with hexagonal wurtzite structure are observed for the ZnO thin film with Mg:Zn = 0.0, 0.02, and 0.04, while a secondary phase of MgO is evolved for the thin film with Mg:Zn = 0.08. The ZnO:Mg-2% thin film exhibits high c-axis preferred orientation. AFM studies reveal that rms roughness of the thin films changes from 7.89 nm to 16.9 nm with increasing Mg concentrations. PL spectra show that the UV-violet emission band around 386-402 nm and the blue emission peak about 460 nm are observed. The optical band gap calculated from absorption spectra and the resistivity of the ZnO thin films increase with increasing Mg concentration. In addition, the effects of Mg concentrations on microstructure, surface topography, PL spectra and electrical properties are discussed.