超细SnO_2纳米晶粒带边光吸收的线度效应

采用超细过滤方法 ,分别制备含有平均线度小于 2nm的超细SnO2 纳米晶粒的酸性和碱性溶胶溶液 .通过动态光散射、X射线衍射和晶粒透射电子显微镜像测量 ,确定了SnO2 晶粒的线度 .对其光吸收谱测量发现 ,超细过滤后酸性和碱性溶胶溶液中晶粒的带边光吸收能量均有明显蓝移 .分析结果表明 ,SnO2 晶粒的线度减小是同类晶粒带边光吸收蓝移的主要原因 .     

SnO$lt;sub$gt;2$lt;/sub$gt;纳米晶体的制备、结构与发光性质

使用软化学方法在碱性溶液中制备出了颗粒尺寸分布均匀的SnO₂纳米颗粒,使用透射电子显微镜（TEM）、X射线衍射（XRD）、光致发光谱（PL）和光吸收谱等方法分析与表征了SnO₂纳米颗粒的结构和光学性能.实验中通过表面活性剂的加入来控制纳米颗粒的结晶与凝聚.XRD,TEM的结果表明,原始制备出的SnO₂纳米颗粒的平均粒径小于4 nm,为完好的晶体状态.纳米颗粒经过400—1000 ℃退火后晶粒尺寸进一步增大.光吸收谱表明,相对于体材料,纳米颗粒的禁带宽度展宽并随颗粒尺寸增大而红移.光致发光谱测试表明,不同温度下退火的SnO₂纳米颗粒在350—750 nm有较强的发光,研究表明这是来源于颗粒表面的氧空位缺陷发光. 关键词： 氧化锡 表面活性剂 纳米颗粒 光致发光     

纳米SnO2材料的穆斯堡尔谱研究

通过X射线衍射,透射电子显微镜和穆斯堡尔谱测量,确定了在本研究中用水热法制备的半导体SnO₂材料为纳米材料,实验给出该材料的结构特点和Sn原子核的超精细参量,并发现600℃时纳米的SnO₂会转变成晶态大颗粒的SnO₂。 关键词：     

低温制备SnO2电子传输层用于钙钛矿太阳能电池

SnO₂具有光稳定性优异、可低温溶液制备等优点被视为电子传输层的优异材料之一,广泛应用于高效稳定的平面异质结钙钛矿太阳能电池.本文在低温(150℃)下采用旋涂工艺制备SnO₂电子传输层,探究了SnO₂前驱体溶液不同浓度(SnO₂质量分数为2.5%—10.0%)下制备的SnO₂电子传输层对钙钛矿太阳能电池性能的影响.通过对SnO₂薄膜进行扫描电子显微镜(SEM)、紫外-可见光(UV-Vis)吸收光谱和透射光谱分析,发现基底的覆盖率、透光率和SnO₂薄膜的带隙随SnO₂前驱液浓度的增加而增大;通过对SnO₂/钙钛矿(MAPbI₃)薄膜进行SEM、UV-Vis、X-射线衍射(XRD)、稳态光致发光(PL)光谱分析,发现SnO₂胶体分散液浓度为7.5%制备的SnO₂层上沉积的MAPbI₃的粒径最大,结晶度最好,具...     

纳米TiO2多孔膜的微结构对染料敏化纳米薄膜太阳电池性能的影响

采用溶胶-凝胶方法，在不同的实验条件下获得平均粒径从15到25nm左右的纳米TiO２2颗粒.利用这些颗粒制备出的纳米多孔薄膜，应用于染料敏化纳米薄膜太阳电池. 通过x射线 衍射仪分析，得到TiO２₂颗粒的晶相以及晶粒度大小，用透射电子显微镜观察 了纳米TiO２₂颗粒的形貌和尺寸.应用于太阳电池的纳米TiO２₂多 孔膜，经基于布朗诺尔-埃米特-泰 勒（BET）的多层吸附理论的比表面积测试和孔径分布测试，获得了多孔膜的微 关键词： 溶胶-凝胶法 2')" href="#">纳米TiO２₂ 染料敏化 太阳电池     

溶胶-凝胶制备ZnO-SiO2复合膜的量子效应和上转换发光

采用溶胶-凝胶技术在玻璃衬底上制备了ZnO薄膜和ZnO-SiO₂复合膜.原子力显微镜照片显示ZnO薄膜具有球状纳米晶粒;可见光-紫外透射光谱表明ZnO-SiO₂复合膜在可见光区的透过率大约是85%,透过率从330 nm开始下降,到290 nm附近降为零.由于量子效应,吸收边出现明显的蓝移.在室温下用不同波长的光激发ZnO-SiO₂复合膜,光致发光谱显示ZnO-SiO₂复合膜对应于激子发射的290 nm附近的紫外发光峰与透射谱所显示的吸收边位置一致,没有出现斯托克斯红移.同时,ZnO-SiO₂复合膜出现了双光子和三光子吸收现象和上转换发光现象. 关键词： 2')" href="#">ZnO-SiO₂ 量子效应 双光子和三光子吸收 上转换发光     

催化剂对热蒸发法生长SnO2纳米晶体质量的影响及其发光光谱研究

用热蒸发法制备了SnO₂纳米结构，并用光致发光方法研究了其光谱特性.发现有催化剂条件下制备的SnO₂纳米带的发光主峰为3.68 eV, 正对应SnO₂纳米晶体的带隙能量; 而无催化条件下制备的SnO₂纳米晶体的发光则以氧空位、悬键和表面态发光为主.并且前者的发光效率比后者提高近两个数量级，这些实验结果说明在有催化条件下制备了高质量的SnO₂纳米带.另外,对其发光光谱进行了Gauss拟合, 从拟合结果发现了(101)和(101)_T孪生晶面的表面态的发光峰. 关键词： 光致发光光谱 半导体纳米晶体 催化剂 2')" href="#">SnO₂     

SnO2微纳米材料的合成及其生长机理研究

利用简单的化学气相沉积法,以Sn粉为源材料合成不同形貌的一维SnO₂纳米棒、纳米线和纳米花等纳米结构,并通过减小载气中的氧含量获得新颖的SnO₂亚微米环状结构.通过调节Sn粉的量和载气中的氧含量、升温速率等试验条件,有效实现SnO₂一维纳米结构的控制生长.采用扫描电子显微镜、能谱仪和X射线衍射仪表征产物形貌、成分和物相结构,并探讨了SnO₂微纳米材料的生长机理. 关键词： 2')" href="#">SnO₂ 纳米结构 亚微米环 生长机理     

氮化硅薄膜中纳米非晶硅颗粒的键合结构及光致发光

采用螺旋波等离子体化学气相沉积技术以N₂/SiH₄/H₂为反应气体制备了镶嵌有纳米非晶硅颗粒的氢化氮化硅薄膜,通过改变N₂流量实现了薄膜从红到蓝绿的可调谐光致发光.傅里叶红外透射和紫外-可见光吸收特性分析表明,所生长薄膜具有较高的氢含量,N₂流量增加使氢的键合结构发生变化,非晶硅颗粒尺寸减小,所对应的薄膜的光学带隙逐渐增加和微观结构有序度减小.可调光致发光(PL)主要来源于纳米硅颗粒的量子限制效应发光,随N₂流量增加,PL的谱线展宽并逐渐增强. 关键词： 傅里叶红外透射谱 光吸收谱 纳米硅粒子镶嵌薄膜 光致发光     

Nb/SnO2复合薄膜的制备、结构及光电性能

用溶胶-凝胶旋涂法在玻璃基底上制备出Nb/SnO₂复合透明导电薄膜,利用XRD,SEM,紫外—可见分光光度计,四探针电阻仪等测试方法对Nb/SnO₂复合薄膜的结构和物性进行了研究.结果表明: 当Nb含量小于0.99at%时,Nb/SnO₂复合薄膜为较纯的四方金红石结构;复合薄膜中晶粒分布均匀,平均尺寸在5—7 nm.当Nb含量小于0.99at%时,Nb/SnO₂复合薄膜的电阻率先减小后增大,当Nb含量为0.37at%时 关键词： 溶胶-凝胶法 2复合薄膜')" href="#">Nb/SnO₂复合薄膜 结构表征 光电性能     

Synthesis and characterization of tin oxide (SnO2) nanocrystalline powders by a simple modified sol–gel route

This paper reports the synthesis and characterization of nanocrystalline tin oxide (SnO₂) powders by a simple method using a chitosan–polymer complex solution. To obtain SnO₂ nanocrystalline powders, the precursor was calcined at 500–600 °C in air for 2 h. The phase composition of calcined samples was studied by X-ray diffraction (XRD). The XRD results confirmed the formation of a SnO₂ phase with tetragonal structure. The particle sizes of the powder were found to be 22–23 nm as evaluated by the XRD line broadening method. TEM investigation revealed that the SnO₂ samples consist of crystalline particles of 19–21 nm. The corresponding selected area electron diffraction analysis further confirmed the formation of the tetragonal structure of SnO₂ without any impurity phases. The optical properties of the samples were explored by Fourier transform infrared spectroscopy, optical absorption and Raman studies. The estimated band gaps of the samples were in the range of 3.44–3.73 eV.     

Grain size effect on the universality of AC conductivity in SnO2

Nanocrystalline tin oxide (SnO₂) material with different grain sizes was synthesized by using a chemical precipitation method. This material was characterized by using the X-ray diffraction and transmission electron microscopy. The electrical properties of compressed nanocrystalline SnO₂ were studied by using impedance spectroscopy. AC conductivity data for SnO₂ material having grain sizes between 9 and 34 nm were analyzed using a power law. The exponent n is found to be 0.5 for bulk (34 nm) and unity for material with grain size below 18 nm. The results show a universal behavior for very low average grain sizes and the non-universal behavior for larger grain sizes even at room temperature.     

High Pressure effects on electrical resistivity and dielectric properties of nanocrystalline SnO2

Nanocrystalline tin oxide (SnO₂) was prepared by chemical precipitation method with different grain sizes. The X-ray diffraction studies showed the structural stability of nanocrystalline SnO₂ under high-pressure. Electrical and dielectric properties were studied on these samples using complex impedance spectroscopy under different hydrostatic pressures. Electrical resistivity and dielectric studies showed a transition in nanocrystalline SnO₂ when it was subjected to high-pressure. The transition pressures obtained from both the resistivity and dielectric measurements agree with each other. The transition pressures were found to increase considerably with the decrease in grain size. Dielectric constant was found to decrease with the reduction of grain size. In order to find whether the transition with pressure is structure- related or not, Raman spectroscopy was done at normal temperature and pressure (NTP) and as a function of pressure at room temperature. Raman modes at NTP showed lines which correspond to tetragonal rutile structure of SnO₂. In situ high-pressure Raman measurements were carried out up to 3.38 GPa. No structural change was found with pressure.     

Optical parameters in SnO2 nanocrystalline textured films grown on p-InSb (111) substrates

Spectroscopic ellipsometry and photoluminescence (PL) measurements on SnO₂ nanocrystalline textured films grown on p-InSb (111) substrates by using radio-frequency magnetron sputtering at low temperature were carried out to investigate the dependence of the optical parameters on the SnO₂ thin film thickness. As the SnO₂ film thickness increases, while the energy gap of the SnO₂ film decreases, its refractive index increases. The PL spectra show that the broad peaks corresponding to the donor-acceptor pair transitions are dominant and that the peak positions change with the SnO₂ film thickness. These results can help improve understanding for the application of SnO₂ nanocrystalline thin films grown on p-InSb (111) substrates in potential optoelectronic devices based on InSb substrates.     

Micro‐Raman investigation of tin dioxide nanostructured material based on annealing effect

Rutile‐structured nanocrystalline tin dioxide (SnO₂) powder was synthesized by the chemical precipitation method using the precursor SnCl₂• 5H₂O. The SnO₂ powder was annealed at different temperatures, namely, 600, 800 and 1000 °C. Micro‐Raman spectra were recorded for both the as‐grown and annealed SnO₂ nanocrystalline samples. Micro‐Raman spectral measurements on the SnO₂ nanoparticle show the first‐order Raman modes A_1g (633 cm⁻¹), E_1g (475 cm⁻¹) and B_2g (775 cm⁻¹), indicating that the grown SnO₂ belongs to the rutile structure. The first‐order A_1g mode is observed as an intense band, whereas the other two modes show low intensity. The full width at half‐maximum and band area of the Raman lines of SnO₂ nanoparticle annealed at various temperatures were calculated. The effect of high‐temperature annealing on the vibrational modes of SnO₂ was studied. The optical image of SnO₂ nanocrystalline material was used to understand the surface morphology effect. Copyright © 2011 John Wiley & Sons, Ltd.     

One-step flame method for the synthesis of coated composite nanoparticles

A simple in situ flame coating method has been developed by designing a new type of coflow diffusion flame burner having a sliding unit. The sliding unit was shown to be very effective in finding a right position where the precursor for coating layer should meet with core particles. SiO₂-coated TiO₂ nanoparticles were first prepared and whether most surfaces of particles were coated was examined by both direct observation of particles through a transmission electron microscope and Zeta potential measurements. Mean core sizes varied from 28 to 109 nm and mean coating thickness was about 2.4 nm for silica-coated titania particles. By simply changing chemical precursors, we demonstrated that SiO₂-coated SnO₂, SnO₂-coated TiO₂, SiO₂–SnO₂-coated TiO₂ nanoparticles could be also synthesized.     

Optical properties of SnO2 nanoparticles

In recent times, considerable research efforts have been focused on the exploration of novel optical properties of nanocrystalline SnO₂ particles such as photoluminescence (PL). In the present work, spherical SnO₂ nanoparticles are synthesized by solid state reaction at different temperatures using tin chloride dihydrate and sodium hydroxide flakes as precursors. Transmission electron micrograph shows uniform and spherical SnO₂ nanoparticles of diameter 30–40 nm. Micro-Raman spectra show an inverse relationship of line-width with SnO₂ particle size. The band gap of SnO₂ is calculated by plotting (αhν)² vs. hν and extrapolating the linear portion of it to α = 0 and found it to be 3.76–4.24 eV. Photoluminescence intensity increases with the increase of solid state reaction temperature up to 873 K. This is attributed to the generation of the oxygen ion vacancies in SnO₂.