Characterizations of octahedral zinc oxide synthesized by sonochemical method

The ultrasonic reaction of zinc nitrate hexahydrate (Zn(NO₃)₂·6H₂O) and hexamethylenetetramine (C₆H₁₂N₄) was investigated by varying the concentration of the reactants, the irradiation time, and the type of sonicator. The morphology, composition, and phase structure of the products were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier Transform Infrared (FTIR) and ultraviolet-visible (UV-vis) spectroscopy. Octahedral zinc oxide (ZnO) micropowders were formed at low concentrations, 0.05 M, of Zn(NO₃)₂·6H₂O and C₆H₁₂N₄ in both lab-made sonicator and commercial ultrasonic bath. However, at concentrations between 0.1 and 1.0 M Zn(NO₃)₂-C₆H₁₂N₄ mainly plate-like zinc hydroxide nitrate hydrate (Zn₅(OH)₈(NO₃)₂(H₂O)₂) resulted with only a small fraction of ZnO, irrespective of the irradiation time employed, highlighting the sensitivity of the system to the concentration of the starting materials. Heat treatment of Zn₅(OH)₈(NO₃)₂(H₂O)₂ at 350 °C in air affords a ZnO phase of irregular morphology. Octahedral ZnO is found to exhibit slightly lower IR absorption and similar UV absorption to that of commercial prismatic hexagonal ZnO, although an extra peak due to small quantities of Zn₅(OH)₈(NO₃)₂(H₂O)₂ is observed.     

Growth and characterization of two new NLO materials from the amino acid family: l-Histidine nitrate and l-Cysteine tartrate monohydrate

Single crystals of organic nonlinear optical (NLO) materials l-Histidine nitrate (C₆H₁₀N₃O₂)⁺ · (NO₃)⁻ and l-Cysteine tartrate monohydrate (C₃H₈NO₂S)⁺ · (C₄H₅O₆)⁻ · H₂O were grown by submerged seed solution method. Characterization of the crystals was made using single crystal X-ray diffraction. Fourier transform infrared (FTIR) spectroscopic studies, optical behaviour such as UV-visible-NIR absorption spectra and second harmonic generation (SHG) conversion efficiency were investigated to explore the NLO characteristics of the above materials. Microhardness measurements and dielectric studies of the compounds were also carried out.     

Synthesis of ZnO-SnO2 composite oxides by CTAB-assisted co-precipitation and photocatalytic properties

ZnO-SnO₂ composite oxides with various molar ratios of Sn:Zn have been synthesized at different calcination temperatures via a facile cetyltrimethylammonium bromide (CTAB)-assisted co-precipitation method with Zn(NO₃)₂·6H₂O and SnCl₄·5H₂O as starting materials. XRD, TEM, SEM and BET were employed to characterize the as-prepared samples. It has been found that amorphous intermediates appear between the evolutions of ZnO and SnO₂ crystals. The photocatalytic properties of the composite oxides were investigated using photocatalytic degradation of methyl orange as the probe reaction. The results show that the ZnO-SnO₂ composite oxide with a cube morphology exhibits the best photocatalytic activity, which was prepared with a molar ratio of Zn:Sn of 2:1 and calcination temperature of 700 °C.     

Well-aligned ZnO rod arrays grown on glass substrate from aqueous solution

Well-aligned ZnO rod arrays have been successfully synthesized on glass substrate from the aqueous solution of Zn(NO₃)₂·6H₂O and C₆H₁₂N₄ (HMT). Some critical issues such as seed layers, concentration and reaction time were investigated. The results show that ZnO seed layers were pre-requisite for the aligned growth of ZnO rod arrays. The length of rods is tunable in a range from 2 μm to 3 μm by varying the solution concentration and reaction time. X-ray diffraction results demonstrate that ZnO rods are wurtzite crystal structures preferentially orienting in the direction of the c-axis. Microstructure observation by scanning electron microscope confirms that ZnO rods grew up perpendicular to the substrate. Room-temperature photoluminescence (PL) spectrum of rod arrays shows a strong emission band at about 396 nm.     

Sensing of LPG with nanostructured zinc oxide thin films grown by spray pyrolysis technique

Nanostructured zinc oxide thin films were prepared by spray pyrolysis technique using Zn(NO₃)₂·6H₂O as the precursor solution. The resulting films were investigated by X-ray diffraction and scanning electron microscopy to know crystal structure, size of crystallites and surface morphology. The films have been found to be polycrystalline zinc oxide, possessing hexagonal wurtzite crystal structure and nanocrystallite with grain size of approximately 30-35 nm. The LPG sensing performance of the films has been investigated at various concentrations of LPG in air at operating temperatures varying from 225 to 400 °C. At 325 °C the maximum responses of 46.3% and 48.9% have been observed, respectively, for concentrations of 0.8 and 1 vol% of LPG in air (1 vol% of LPG in air corresponds to 50% LEL of LPG in air). The recovery time has been found to be less than the response time for all concentrations of LPG. A possible reaction mechanism of LPG sensing has been proposed.     

Fabrication of three-dimensional dendrite-like CeO2 crystallites via simple template-free solution route

Highly uniform three-dimensional dendrite-like CeO₂ crystallites were successfully prepared in large quantities with a thermal decomposition of precursor approach applied. The precursor with an average size of 10 μm was prepared in an aqueous solution containing Ce(NO₃)₃·6H₂O, CO(NH₂)₂ and ammonia at 160 °C with no additional phase. The influence of ammonia on the dendrites formation was discussed. The dendritic pattern of precursor almost remained in the as-prepared product. The optical absorption spectrum indicates that CeO₂ dendrites have a direct band gap of 3.52 eV.     

Facile fabrication of Zn/Zn5(OH)8Cl2·H2O flower-like nanostructure on the surface of Zn coated with poly (N-methyl pyrrole)

Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructures was electrodeposited on the coated Zn with poly (N-methyl pyrrole) in 0.1 M Zn (NO₃)₂ and 0.1 M KCl solution. The morphology and the structure of the Zn/Zn₅(OH)₈Cl₂·H₂O were characterized by Field Emission Scanning Electron Microscopy (FESEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray diffraction analysis (XRD). The FT-IR results showed special peaks at 908 and 728 cm⁻¹ related to Zn₅(OH)₈Cl₂·H₂O. The FESEM results indicated that Zn/Zn₅(OH)₈Cl₂·H₂O consists of a flower-like nanostructure and these flower-shaped structures contain many shaped nanopetals with the thickness of 27.8 nm. The XRD result confirmed that the major phase of electrodeposited product in 0.1 M KCl as supporting electrolyte was Zn₅(OH)₈Cl₂·H₂O. The ability of PMPy to create a thin film and the existence of several pores in its matrix act as a mold for the growth of Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructure. The trapping of Cl⁻ and OH⁻ within pores can be considered as the reason for the formation of flowerlike Zn/Zn₅(OH)₈Cl₂·H₂O nanostructures in 0.1 M KCl.     

Properties of NiO thin films deposited by chemical spray pyrolysis using different precursor solutions

NiO thin films have been deposited by chemical spray pyrolysis using a perfume atomizer to grow the aerosol. The influence of the precursor, nickel chloride hexahydrate (NiCl₂·6H₂O), nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O), nickel hydroxide hexahydrate (Ni(OH)₂·6H₂O), nickel sulfate tetrahydrate (NiSO₄·4H₂O), on the thin films properties has been studied. In the experimental conditions used (substrate temperature 350 °C, precursor concentration 0.2-0.3 M, etc.), pure NiO thin films crystallized in the cubic phase can be achieved only with NiCl₂ and Ni(NO₃)₂ precursors. These films have been post-annealed at 425 °C for 3 h either in room atmosphere or under vacuum. If all the films are p-type, it is shown that the NiO films conductivity and optical transmittance depend on annealing process. The properties of the NiO thin films annealed under room atmosphere are not significantly modified, which is attributed to the fact that the temperature and the environment of this annealing is not very different from the experimental conditions during spray deposition. The annealing under vacuum is more efficient. This annealing being proceeded in a vacuum no better than 10⁻² Pa, it is supposed that the modifications of the NiO thin film properties, mainly the conductivity and optical transmission, are related to some interaction between residual oxygen and the films.     

Low-temperature growth of ZnO nanorods on PET fabrics with two-step hydrothermal method

An effective low-temperature growth method to fabricate hexagonally oriented ZnO nanorod arrays onto PET fabrics is reported. The effect of substrate pre-treatment and C₆H₁₂N₄ concentration on the structure of ZnO nanorod arrays were investigated in details by X-ray diffraction (XRD), FE-SEM and ultraviolet protection factor (UPF). The results show that substrate pre-treatment, C₆H₁₂N₄ concentration indeed have great influence on the growth of ZnO nanorod arrays. It is indispensable to introduce a ZnO seed layer on the substrate and under growth condition of n(C₆H₁₂N₄):n[Zn(NO₃)₂] = 1:1, T = 90 °C, t = 3 h, the well-aligned ZnO nanorod arrays with 40-50 nm in diameter and 300-400 nm in length were achieved on the pre-treated PET fabrics. The ZnO nanorods grown on PET fabrics possessed an ultrahigh ultraviolet protection factor of 480.52 in this study, indicating an excellent protection against ultraviolet radiation in comparison with the untreated PET fabrics.     

Static susceptibility and heat capacity studies on V3O7·H2O7 nanobelts

V₃O₇·H₂O nanobelts were prepared by a hydrothermal method at 190 °C using V₂O₅·nH₂O gel and H₂C₂O₄·2H₂O as starting agents. The obtained nanobelts have diameters ranging from 40 to 70 nm with lengths up to several micrometers. Measurements of the static magnetic susceptibility and the specific heat show a discontinuous phase transition at around T=145 K, which separates two regions of paramagnetic behavior.     

Microwave-assisted synthesis of SrFe12O19 hexaferrites

Ultra-fine and homogeneous SrFe₁₂O₁₉ hexaferrites were synthesized by a microwave-assisted calcination route. The calcined precursors were prepared by a sol-gel auto-combustion method using Fe(NO₃)₃·9H₂O, Sr(NO₃)₂ and citric acid as starting materials. The structures, powder morphology and magnetic properties of the products were characterized by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer. The results showed that microwaves are helpful to reduce the calcination temperature and shorten the calcination time. The ferrites with saturation magnetization, remanence and intrinsic coercivity of 54.80 emu/g, 29.52 emu/g and 5261 Oe, respectively, were obtained in samples calcined at 800 °C for 80 min.     

Solvothermal synthesis and characterization of CdSe nanocrystals with controllable phase and morphology

Zinc blende (ZB) CdSe hollow nanospheres were solvothermally synthesized from the reaction of Cd(NO₃)₂·4H₂O with a homogeneously secondary Se source, which was first prepared by dissolving Se powder in the mixture of ethanol and oleic acid at 205 °C. As Se power directly reacted with Cd(NO₃)₂·4H₂O in the above mixed solvents, wurtzite (W) CdSe solid nanoparticles were produced. Time-dependent experiments suggested that the formation of CdSe hollow nanospheres was attributed to an inside-out Ostwald ripening process. The influences of reaction time, temperature and ethanol/oleic acid volume ratio on the morphology, phase and size of the hollow nanospheres were also studied. Infrared (IR) spectroscopy investigations revealed that oleic acid with long alkene chains behaved as a reducing agent to reduce Se powder to Se²⁻ in the synthesis. Photoluminescence (PL) measurements showed that the ZB CdSe hollow nanospheres presented an obvious blue-shifted emission by 42 nm, and the W CdSe solid nanoparticles exhibited a band gap emission of bulk counterpart.     

Hydrothermal synthesis and characterization of nanocrystalline Zn-Mn spinel

Hydrothermal method had been used to successfully synthesize the nanocrystalline spinel zinc manganese oxide (ZnMn₂O₄) directly from Zn(CH₃COO)₂·2H₂O, NaOH, Mn(NO₃)₂ and H₂O₂ at 170 °C for the reaction time of 48 h. The effects of the synthesis conditions, such as the Zn/Mn molar ratio, the reaction temperature, the reaction time, the zinc source and the concentrations of NaOH and H₂O₂, on the formation of the Zn-Mn spinel were investigated. The products were characterized by means of X-ray diffraction (XRD), inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The results indicated that the compositions of the Zn-Mn spinel with the tetragonal structure were Zn_1.14Mn_1.86O₄. Scanning electron microscope (SEM) and transmission electron microscopy (TEM) images showed that the products at 170 °C were with square-shaped nanocrystalline spinel with the particle size of about 20-50 nm. The thermal behaviors of the products were investigated by thermogravimetric analysis (TG).     

Preparation of Nd-doped BiFeO3 films and their electrical properties

The Nd-doped BiFeO₃ thin films were prepared on SnO₂(FTO) substrates spin-coated by the sol–gel method using Nd(NO₃)₃·6H₂O, Fe(NO₃)₃·9H₂O and Bi(NO₃)₃·5H₂O as raw materials. The microstructure and electric properties of the BiFeO₃ thin films were characterized and tested. The results indicate that the diffraction peak of the Nd-doped BiFeO₃ films is shifted towards right as the doping amounts are increased. The structure is transformed from the rhombohedral to pseudotetragonal phase. The crystal grain is changed from an elliptical to irregular polyhedron. Structure transition occurring in the Bi_0.85Nd_0.15FeO₃ films gives rise to the largest Pr of 64 μC/cm². The leakage conductance of the Nd doped thin films is reduced. The dielectric constant and dielectric loss of Bi_0.85Nd_0.15FeO₃ thin film at 10 kHz are 190 and 0.017 respectively.     

Growth and characterization of a new organic NLO material: Glycine nitrate

Single crystals of glycine nitrate [(C₂H₆NO₂)⁺ · (NO₃)⁻] were grown using submerged seed solution method. The crystals were characterized by using single crystal X-ray diffraction and density measurements. Spectroscopic, thermal and optical studies were carried out for analyzing the presence of the functional groups, thermal stability, decomposition and transparency of the sample. These studies showed that the crystals are thermally stable upto 145 °C and transparent for the fundamental and second harmonic generation of Nd:YAG (λ = 1064 nm) laser. Second harmonic generation (SHG) conversion efficiency was investigated to explore the NLO characteristics of this material. Microhardness and dielectric studies were also carried out.     

Electrodeposition from ZnO nano-rods to nano-sheets with only zinc nitrate electrolyte and its photoluminescence

This very paper focuses on the synthesis of ZnO nano-structures by means of electro-chemical-deposition process. The crystalline structure and morphologies of the prepared ZnO were characterized with X-ray diffraction and scanning electronic microscopy, respectively. It is found that in case of low Zn(NO₃)₂·6H₂O electrolyte concentration the fast growth mode in the c-axis direction leaded to the formation of 1D nanostructure of ZnO. On the other hand, at high concentration, this fast growth mode was restricted because the absorbed NO₃⁻ on (0 0 0 1) plane would bond with Zn²⁺ ions, which, therefore, resulted in the formation of 2D nanostructure of ZnO. Room temperature photoluminescence performances of different ZnO structures were also investigated. A blue shift of 15 nm for ZnO nano-sheets has been found as the shapes of ZnO evolved from nano-rods to nano-sheets.     

Ni-Al layered double hydroxides modified with citrate, malate, and tartrate: Preparation by coprecipitation and uptake of Cu from aqueous solution

We report on aqueous Cu²⁺ uptake by Ni-Al layered double hydroxides (Ni-Al LDHs) modified with citrate (C₆H₅O₇³⁻), malate (C₄H₄O₅²⁻), and tartrate (C₄H₄O₆²⁻) anions via coprecipitation. Dropwise addition of a mixed aqueous solution of Ni(NO₃)₂ and Al(NO₃)₃ to the respective organic acid solutions at a constant pH of 7.0-9.0 afforded LDHs with intercalated C₆H₅O₇³⁻ and Ni(C₆H₅O₇⁾⁻, C₄H₄O₅²⁻, and C₄H₄O₆²⁻ in their interlayers. The anions were also likely adsorbed on the LDH surface. Citrate·Ni-Al LDH could rapidly take up Cu²⁺ at a constant pH of 5.0, mainly via chelation by the intercalated and adsorbed anions, rather than coprecipitation with dissolved Al³⁺ to form Cu-Al LDH. By contrast, malate and tartrate were not active as chelating agents, probably because they formed bridges between brucite-like layers by direct coordination of the two −COO⁻ groups with Al³⁺ in those layers.     

Preparation and characterization of SrSnO3 nanorods

Perovskite strontium stannate (SrSnO₃) nanorods were prepared by annealing the precursor SnSr(OH)₆ nanorods at 600 °C for 3 h. The precursor nanorods were hydrothermally synthesized at 160 °C for 16 h using Sr(NO₃)₂ and SnCl₄·5H₂O as starting materials in the presence of surfactant cetyltrimethyl ammonium bromide (CTAB). As-prepared samples were characterized by X-ray diffraction (XRD), thermogravimetric-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and infrared ray spectroscopy (IR). The results show that the as-synthesized powders are made of SrSnO₃ one-dimensional nanorods of about 0.2-1 μm length and 100-150 nm diameter. Possible formation mechanism of SrSnO₃ with nanorod structure under certain conditions was preliminarily analyzed, in which it was thought that CTAB played an important role in the formation process of the nanorod structure. Electrochemical performance of the samples versus Li metal was also evaluated for possible use in lithium-ion batteries.     

One-step electrodeposition process to fabricate cathodic superhydrophobic surface

In this work, a rapid one-step process is developed to fabricate superhydrophobic cathodic surface by electrodepositing copper plate in an electrolyte solution containing manganese chloride (MnCl₂·4H₂O), myristic acid (CH₃(CH₂)₁₂COOH) and ethanol. The superhydrophobic surfaces were characterized by means of scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The shortest electrolysis time for fabricating a superhydrophobic surface is about 1 min, the measured maximum contact angle is 163° and rolling angle is less than 3°. Furthermore, this method can be easily extended to other conductive materials. The approach is time-saving and cheap, and it is supposed to have a promising future in industrial fields.     

Intercalation behavior of barium phenylphosphonate

The dependence of basal spacing and water content of BaC₆H₅PO₃·xH₂O on the relative humidity was studied. Intercalates of 1-alkylamines (C₂-C₁₀) and 1-alkanols (C₃-C₁₀) were prepared from barium phenylphosphonate dihydrate and also from anhydrous host and characterized by powder X-ray diffraction and thermogravimetric analysis. The intercalates of alkanols and alkylamines prepared from dihydrate are quite stable at ambient conditions and contain one guest molecule per formula unit. The guest molecules are probably arranged in monomolecular way and are perpendicular to the host layers in the case of amines or tilted to the host layers at an angle of about 80° in the case of alkanols. The intercalates prepared from anhydrous host are unstable and their basal spacings indicate parallel arrangement of the guests chains. Formation of mixed intercalates was not observed when barium phenylphosphonate dihydrate was contacted with a mixture of alkanols or amines.