声驻波场中空化泡的动力学特性

以水为工作介质, 考虑了液体的可压缩性, 研究了驻波声场中空化泡的运动特性, 模拟了驻波场中各位置处空化泡的运动状态以及相关参数对各位置处空化泡在主Bjerknes力作用下运动方向的影响. 结果表明: 驻波声场中, 空化泡的运动状态分为三个区域, 即在声压波腹附近空化泡做稳态空化, 在偏离波腹处空化泡做瞬态空化, 在声压波节附近, 空化泡在主Bjerknes 力作用下, 一直向声压波节处移动, 显示不发生空化现象; 驻波场中声压幅值增加有利于空化的发生, 但声压幅值增加到一定上限时, 压力波腹区域将排斥空化泡, 并驱赶空化泡向压力波节移动, 不利于空化现象的发生; 当声频率小于初始空化泡的共振频率时, 声频率越高, 由于主Bjerknes 力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生, 尤其是驻波场液面的高度不应是声波波长的1/4; 当声频率一定时, 空化泡初始半径越大越有利于空化现象的发生, 但当空化泡的初始半径超过声频率的共振半径时, 由于主Bjerknes力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生.     

超声在液体中的非线性传播及反常衰减

本文从广义的Navier-Stokes流体方程出发,考虑到流体介质的黏滞性和存在的热传导,导出了更接近实际流体的三维非线性声波动方程.鉴于声传播所涉及的空间和时间尺度的复杂性和多样性,文中针对一维情形下的非线性波动方程进行了求解和分析.由方程的二级近似解可以看出,声压振幅的衰减遵循几何级数规律,而且驱动声波的频率越高声压的衰减就越快.在满足条件ωb《ρ0c_0~2时,基波的衰减系数与驱动频率的平方及耗散系数的乘积成正比;二次谐波的衰减规律更加复杂,与频率的更高次幂相关.对声衰减系数及声压的分布进行数值计算发现,声压的分布还与初始的声压幅值及频率有关,初始的声压与频率越高衰减得越快.另外,当声压高于液体的空化阈值时,液体中就会出现大量的空化泡,文中模拟了单个空化泡的运动,发现随着声压的增大空化泡的振动越剧烈、空化泡所受的黏滞力变大,随着声波作用时间的增大黏滞力的幅值迅速增大并与驱动声压值同阶,因而空化泡的非线性径向运动引起的声衰减不容忽视.结果表明,驱动声压越高在空化区域附近引起的声衰减越快、输出的声压越低.     

液体薄层中环链状空化泡云结构稳定性分析

为分析超声空化的薄层液体中稳定的环状气泡链结构,本文考虑气泡间次级声辐射影响,得到了表征气泡间相互作用的气泡基本动力学方程以及次Bjerknes力的表达式,数值分析了气泡平衡半径、声波频率和声压对纯液体区可能出现的单气泡所受的次Bjerknes力,发现环形泡链能够吸引液体区内的新生的半径小于2μm的气泡,这可能是一定条件下环形气泡链能够稳定存在的原因.随着驱动声波压力增加,气泡数密度增加,气泡间的耦合作用增强,液体区内的环形泡链结构可能被液体区内出现的大气泡或者气泡团破坏,进而导致环形结构演变成柱状、雾状乃至整个液体区均充满空化泡的情况发生.通过高速摄影机观察了强声场作用下换能器辐射面外侧液体薄层内空化初生至形成空化云团簇的整个过程,在空化云团簇中发现了局部同步崩溃并形成类纯液体薄层的现象,该液体薄层边界随时间振荡持续约4个声周期后被空化云团簇吞没,局部类纯液体区出现的位置具有随机性.实验观察结果和理论预测具有很好的一致性.     

超声波声孔效应中气泡动力学的研究

在超声快速制取组织细胞病理切片的过程中，发现激励信号对切片制取效果有明显的影响.为了掌握超声激励信号对组织细胞的影响规律，达到快速制取病理切片的最佳状态，从气泡空化模型入手，通过改变激励信号频率、声压、气泡初始半径和液体黏滞系数等参量，研究了声孔效应中气泡动力学激励机制.数值计算表明：空化泡振动随激励声压增强而升高，随液体黏滞系数增强而减弱；一定频率范围内空化泡振动能保持在膨胀、收缩和振荡的稳定空化状态，存在空化泡稳态振动的最佳激励频率；一定初始半径能保证空化泡产生稳定的振动，存在空化泡稳态振动幅度最大的初始半径.实际操作中，在频率、声压、初始半径和黏滞系数综合作用的若干空化阈内，声孔效应使超声快速法制取细胞组织切片获得最佳效果. 关键词： 声孔效应 超声空化 气泡振动 稳态空化域     

声场中双空化泡的运动特性

空化泡的运动特性是声场作用下的动力学行为,受空化泡初始半径,声压幅值,驱动声压频率,液体特性等众多因素的影响,是个复杂工程。本文从双空化泡运动方程出发,考虑到液体粘滞系数、空化泡辐射阻尼项的影响,研究了不同初始半径、驱动声压频率、驱动声压幅值、液体粘滞系数下空化泡泡壁的运动情况,研究结果表明不同初始半径、外界驱动声压频率、驱动声压幅值、液体粘滞系数均会对空化泡的膨胀比和空化泡的溃灭时间有一定影响。     

声致空化简介

文章对强声波尤其是超声波通过液体介质时发生空化现象的成因及其作用作一简介.     

声场中气泡运动的混沌特性

以水为工作介质,考虑了液体的可压缩性,研究了声场中气泡的运动特性,模拟了声波频率、声压幅值、气泡初始半径以及液体的表面张力和黏滞系数的变化对气泡运动状态的影响. 分析了空化处理效果与气泡运动状态之间关系. 结果表明:气泡运动处于混沌状态,是提高声空化降解有机污染物能力的最重要因素. 关键词： 声空化 混沌 相图 功率谱图     

强超声在空化液体中的反常衰减

采用自动控制系统,逐点测量了长方形水槽内液体中不同位置的声压。研究发现,随着驱动声压的增大,近场声压持续增大,但衰减速度也加快,而远场声压会经历一个先上升后下降的反常过程。通过对容器中不同位置声压进行频谱分析,得到声波不同频率分量随传播距离的变化规律。结合频谱的分析表明,上述反常过程的原因是高驱动声压下气泡的非线性振动将更多声能量转移至衰减较快的高次谐波,从而导致远场的声压反而低于较低驱动时对应的声压。     

含气泡液体中的非线性声传播

考虑到分布在液体中的气泡是声波在含气泡液体中传播时引起非线性的一个很重要的因素,本文研究了声波在含气泡液体中的非线性传播.将气体含量的影响引入到声波在液体中传播的方程中,从而得到声波在气液混合物中传播的数学模型.通过对该模型进行数值模拟发现,气体含量、驱动声场声压幅值及驱动声场作用时间均会影响到气液混合物中的声场分布及声压幅值大小.液体中的气泡会"阻滞"液体中声场的传播并将能量"聚集"在声源附近.对于连续大功率的驱动声场来说,液体中的气泡会"阻滞"气液混合物中声场及其能量的传播.     

可压缩液体中气泡的声空化特性

利用新提出的Gilmore-NASG模型,在考虑液体可压缩效应的边界条件下,研究了可压缩液体中气泡的声空化特性,并与利用原有KM-Vd W模型计算得到的结果进行了比较.结果表明,相比于KM-Vd W模型,由于Gilmore-NASG模型采用新的状态方程来描述气体、液体以及由可压缩性引起的液体密度变化及声速变化,所以用Gilmore-NASG模型得到的空化气泡的压缩比更大、崩溃深度更深、温度和压力峰值更高.随着驱动声压幅值的增大,两种模型给出的结果差别愈加明显,而随着驱动频率的增大,两种模型给出的结果差别逐渐减小.这表明,在充分考虑泡内气体、周围液体在不同温度和压强下共体积的变化所导致的介质可压缩特性下,气泡内的温度和压强可能达到更高值.同时, Gilmore-NASG模型还预测出了气泡壁处液体的密度变化、压力变化、温度变化以及液体中的声速变化.因此, Gilmore-NASG模型在研究高压状态下气泡的空化特性以及周围液体对气泡空化特性的影响方面具有优点.     

Sonoluminescence and acoustic emission spectra at different stages of cavitation zone development

The way in which a cavitation zone develops in a focused pulsed ultrasound field is studied in this work. Sonoluminescence (SL), total hydrophone output and cavitation noise spectra have been recorded across a gradual, smooth increase in applied voltage. It is shown that the cavitation zone passes through a number of stages of evolution, according to increasing ultrasound intensity, decreasing pulse period and increasing ultrasound pulse duration. Sonoluminescence is absent in the first phase and the hydrophone output spectra consists of a main line with two or three harmonics whose intensity is much lower than that of the main (fundamental) line. The second stage sees the onset of SL whose intensity increases smoothly and is accompanied by the appearance of higher harmonics and subharmonics in the cavitation noise spectra. In some cases, the wide-band (WBN) component can be seen in noise spectra during the final part of the second stage. In the third stage, SL intensity increases significantly and often quite sharply, while WBN intensity increases in the same manner. This is accompanied by a synchronous increase in the absorption of ultrasound by the cavitation zone, which is manifested in a sharp decrease in the hydrophone output. In the fourth stage, both SL and WBN intensities tend to decrease despite the increased voltage applied to the transducer. Furthermore, the fundamental line tends to decrease in strength as well, despite the increasing ultrasound intensity. The obtained results clearly identify the different stages of cavitation zone development using cavitation noise spectra analyses. We then hypothesize that three of the above stages may be responsible for three known types of ultrasound action on biological cells: damping viability, reversible cell damage (sonoporation) and irreversible damage/cytotoxicity.     

Sound field measurement in a double layer cavitation cluster by rugged miniature needle hydrophones

During multi-bubble cavitation the bubbles tend to organize themselves into clusters and thus the understanding of properties and dynamics of clustering is essential for controlling technical applications of cavitation. Sound field measurements are a potential technique to provide valuable experimental information about the status of cavitation clouds. Using purpose-made, rugged, wide band, and small-sized needle hydrophones, sound field measurements in bubble clusters were performed and time-dependent sound pressure waveforms were acquired and analyzed in the frequency domain up to 20 MHz. The cavitation clusters were synchronously observed by an electron multiplying charge-coupled device (EMCCD) camera and the relation between the sound field measurements and cluster behaviour was investigated. Depending on the driving power, three ranges could be identified and characteristic properties were assigned. At low power settings no transient and no or very low stable cavitation activity can be observed. The medium range is characterized by strong pressure peaks and various bubble cluster forms. At high power a stable double layer was observed which grew with further increasing power and became quite dynamic. The sound field was irregular and the fundamental at driving frequency decreased. Between the bubble clouds completely different sound field properties were found in comparison to those in the cloud where the cavitation activity is high. In between the sound field pressure amplitude was quite small and no collapses were detected.     

超声空化现象影响因素的实验研究

超声空化在许多不同的学科和工业生产中有着广泛的应用。超声空化的应用与声场的分布及空化的机理密切相关,精准地反映空化场和空化机理是超声空化技术实际应用的关键。该文通过分析采集的声信号和金属箔膜空蚀法对空化区域随液位发生变化的现象进行研究,并利用Matlab对金属箔膜空蚀程度量化。实验发现,超声波会在液面与实验箱体底部形成驻波场。在某一液体温度下,随着液位高度的变化,超声空化现象的出现具有周期性。并且,在同一液位下,当超声功率改变时,空化区域强度分布情况随之改变。小功率时各空化区域空化强度分布均匀,当功率增大到一定时,会出现空化屏蔽现象。该研究为超声清洗设备的改良提供了借鉴,对进一步认识和利用超声空化效应具有重要意义。     

液体薄层中的超声空化*

液体薄层中的超声空化,因其边界及所处空间的特殊性,而呈现出非常独特的空化结构和演化行为,在超声清洗、超声钎焊、表面处理、近场声悬浮、超声化学等领域都有所应用。该文梳理了近几年该课题组在液体薄层中的超声空化研究中的一些成果,力图揭示液体薄层内空泡、空化云、空化场的运动和分布规律,及其产生、发展和演化过程,以期对液体薄层中的超声空化行为有一个相对清晰和完整的认识。     

Numerical simulation of cavitation bubble dynamics induced by ultrasound waves in a high frequency reactor

The use of high frequency ultrasound in chemical systems is of major interest to optimize chemical procedures. Characterization of an open air 477 kHz ultrasound reactor shows that, because of the collapse of transient cavitation bubbles and pulsation of stable cavitation bubbles, chemical reactions are enhanced. Numerical modelling is undertaken to determine the spatio-temporal evolution of cavitation bubbles. The calculus of the emergence of cavitation bubbles due to the acoustic driving (by taking into account interactions between the sound field and bubbles' distribution) gives a cartography of bubbles' emergence within the reactor. Computation of their motion induced by the pressure gradients occurring in the reactor show that they migrate to the pressure nodes. Computed bubbles levitation sites gives a cartography of the chemical activity of ultrasound. Modelling of stable cavitation bubbles' motion induced by the motion of the liquid gives some insight on degassing phenomena.     

Identification approach of acoustic cavitation via frequency spectrum of sound pressure wave signals in numerical simulation

In a sono-reactor, complex ultrasound pressure wave signal can be detected, containing multiple information related to acoustic cavitation. In this present study, acoustic cavitation in a cylinder is investigated numerically. Via Fast Fourier Transfer (FFT), the sound pressure signals from sonotrode emitting surface are separated into harmonics, sub/ultra-harmonics and cavitation white noise: (1) the appearance of harmonics proved the non-linear propagation of ultrasound, (2) at the vibratory amplitude from 5∼20μm, only harmonics exists in the frequency spectra, corresponding to expansion and compression of non-condensable gas (NCG), (3) at the vibratory amplitude range of 30∼50μm, the occurrence of sub/ultra-harmonics demonstrated gaseous cavitation occurred, and (4) at the vibratory amplitude higher than 55μm, cavitation white noise arose, pointing out the initiation of vaporous cavitation. Based on the combination of frequency spectra and cavitation zones distribution, the acoustic cavitation state in water liquid is determined.     

混响场中脉冲超声空化效应的研究

本文实验研究了不同脉冲宽度的８２０ｋＨｚ超声波的空化效应，结果得出，空化致自基产量随脉冲宽度及声强呈现规律性变化，尤其观察到了“脉冲空化峰”现象，本文从液面受迫振动角度出混响场中“脉冲空化峰”现象的机制。     

Cavitation dose in an ultrasonic cleaner and its dependence on experimental parameters

The aluminum foil erosion method is widely used in cavitation activity studies of ultrasonic cleaners. However, owing to its limited sensitivity, it is difficult to observe the effects of various experimental parameters on the cavitation activity using this method. In the present work, a higher-sensitivity method for quantifying cavitation activity as a cavitation dose based on passive cavitation detection was presented. The influences of various factors (e.g., insonation duration, driving power, gas content, temperature and cleaning agents) were studied for this system. The results showed that the cavitation dose became unstable over long insonation times, and that the instability was more significant at high power. Generally, the cavitation activity could be enhanced by increasing the power, gas content, and the concentration of a cleaning agent. However, due to the exhaustion of the cavitation gas nuclei, the cavitation activity might tune to saturate of even decrease slightly when some impact parameters (e.g., acoustic driving power, gas content and the concentration of the cleaning agent) are above a certain level of each of these parameters.