a-Si∶O∶H薄膜微结构及其高温退火行为研究

以微区Raman散射、X射线光电子能谱和红外吸收对等离子体增强化学气相沉积(PECVD)法制备的氢化非晶硅氧(a-Si∶O∶H)薄膜微结构及其退火行为进行了细致研究.结果表明a-Si∶O∶H薄膜具有明显的相分离结构,富Si相镶嵌于富O相之中,其中富Si相为非氢化四面体结构形式的非晶硅(a-Si),富O相为Si,O,H三种原子随机键合形成的SiO_x∶H(x≈1.35).经1150℃高温退火,薄膜中的H全部释出;SiO_x∶H(x≈1.35)介质在析出部分Si原子的同     

掺铒纳米晶硅和掺铒非晶纳米硅薄膜的发光性质

采用等离子体增强化学气相沉积（PECVD）方法制备含有纳米晶硅的SiO2（NCSO）和含有非晶纳米硅颗粒的氢化非晶氧化硅（a—SiOx：H）薄膜。采用离子注入和高温退火方法将稀土Er掺入含有纳米晶硅（ncSi）和非晶纳米硅（a—n—Si）颗粒的基体中。利用IFS／20HR傅里叶变换红外光谱仪和微区拉曼散射光谱仪研究含有纳米晶硅和非晶纳米硅颗粒的薄膜掺稀土前后的发光特性。结果表明来自Be-Si在800nm的发光强度比来自a—SiOx：H基体中非晶纳米硅的发光强度高近一个数量级,而来自a-SiOx：H在1．54μm的发光强度比NCSO高4倍。还研究了掺铒a-SiOx：H薄膜中Si颗粒和Er^3＋的发光强度随退火温度的变化,结合掺铒纳米晶硅和非晶纳米硅薄膜发光强度随Er掺杂浓度变化和Raman散射等的测量结果,进一步明确指出a-Si颗粒在Er^3＋的激发中可以起到和nc-Si同样的作用,即作为光吸收介质和敏化剂的作用。     

氢化非晶硅薄膜退火形成的纳米硅及其光致发光

本文报道对氢化非晶硅(a-Si:H)薄膜在600～620℃温度下快速退火10s可以形成纳米晶硅(nc-Si),其Raman散射表明,在所形成的nc-Si在薄膜中的分布是随机的,直径在1.6～15nm范围内,并且在强激光辐照下观察了nc-Si在薄膜中的结晶和生长情况.经退火所形成的nc-Si可见光辐射较弱,不能检测到它们的光致发光(PL),但用氢氟酸腐蚀钝化后则可检测到较强的红PL,并且钝化后的nc-Si在空气中暴露一定的时间后,其辐射光波长产生了蓝移.文中就表面钝化和量子限制对可见光辐射的重要性作了讨论.     

纳米硅薄膜退火特性

对使用等离子体增强化学汽相沉积(PECVD)法在不同淀积条件下制备的非晶硅(a-Si:H)、微晶硅(μc-Si:H)和纳米硅(nc-Si:H)薄膜在200—600℃温度范围进行常规退火研究。用共振核反应技术测量了样品中氢含量C_H值及退火对氢含量及其分布的影响。通过室温下对暗电导率的测量得到退火对nc-si:H薄膜电导率的影响,并与a-Si:H,μc-Si:H薄膜的退火行为作了比较。使用紫外/可见/近红外分光光度计对样品透射率进行了测量,分析计算得到了退火温度T_a与ac-Si:H薄膜光学带隙E_g~(o 关键词：     

a-SiCx:H/nc-Si:H多层薄膜的室温时间分辨光致可见发光

在等离子体增强化学气相沉积(PECVD)系统中,通过控制进入反应室的气体种类逐层沉积非晶SiCx：H(a-SiCx：H)和非晶Si：H(a-Si：H)薄膜,然后经过高温热退火处理,成功制备了晶化纳米a-SiCx：H／nc-Si：H(多晶SiC和纳米Si)多层薄膜。利用截面透射电子显微镜技术分析了a-SiCx：H／nc-Si：H多层薄膜的结构特性。通过对晶化样品的时间分辨光致发光谱的研究,结果表明：随着退火温度的升高,发光峰位置开始出现一些红移现象：当退火温度为900℃时,样品的发光强度和发光衰减时间分别达到最大值和最小值;随着退火温度的继续升高,发光峰位置又开始出现蓝移现象。由此探讨纳米a-SiCx：H／nc-Si：H多层薄膜的发光特性和发光机理。     

渐变带隙氢化非晶硅锗薄膜太阳能电池的优化设计

利用一维微电子-光电子结构分析软件(AMPS-1D)在AM1.5G(100 mW/cm2)、室温条件下模拟和比较了有、无渐变带隙氢化非晶硅锗(a-SiGe:H)薄膜太阳能电池的各项性能.计算结果表明:渐变带隙结构电池具有较高的开路电压(V oc)和较好的填充因子(FF),转换效率(E ff)比非渐变带隙电池提高了0.477%.研究了氢化非晶硅(a-Si:H)、氢化非晶碳化硅(a-SiC:H)和氢化纳米晶硅(nc-Si:H)三种不同材料的窗口层对a-SiGe:H薄膜太阳能电池性能的影响.结果显示:在以nc-Si:H为窗口层的电池能带中,费米能级E F已经进入价带,使得窗口层电导率及电池开路电压有所提高,又由于ITO与p-nc-Si:H的接触势垒较低,使得接触处的电场降低,更有利于载流子的收集.另一方面,窗口层与a-SiGe:H薄膜之间存在较大的带隙差,在p/i界面由于能带补偿作用形成了价带势垒(带阶)?E v,阻碍了空穴的迁移,因此我们在p/i界面引入缓冲层,使得能带补偿作用得到释放,更有利于空穴的迁移和收集,得到优化后单结渐变带隙a-SiGe:H薄膜结构太阳能电池的转换效率达到了9.104%.     

a-Si:H薄膜的表面光电压谱和光电化学特性研究

采用表面光电压谱和光电化学方法，对不同掺杂类型的氢化非晶硅(s-Si:H)薄膜的光伏响应和光电化学特性进行了研究，测定了a-Si:h薄膜的能带结构，为a-Si:H薄膜在太阳能电池上的应用提供了有用的基础数据和简单光伏测量方法。     

二维移相光栅光强分布的计算及在制备有序纳米硅阵列中的应用

从菲涅耳衍射积分的一般形式出发,结合二维（2D）移相光栅掩模(PSGM)的具体参数,通过数值计算得到了作用于样品表面的光强分布.实验上,采用激光干涉晶化的方法,利用周期为400 nm的2D-PSGM调制KrF准分子激光器的脉冲激光束斑的能量分布,在氢化非晶硅（a-Si:H）薄膜上直接制备了2D的有序纳米硅（nc-Si）阵列.测试结果表明：2D的nc-Si阵列的周期和PSGM的相一致,晶化区域与理论模拟的结果符合得很好. 关键词： 纳米硅 激光干涉晶化 移相光栅 菲涅耳衍射     

激光干涉结晶法制备一维周期结构的纳米硅阵列

利用激光干涉结晶方法,采用周期为400 nm的一维(1D)移相光栅掩模调制KrF准分子激光器的脉冲激光束斑的能量分布,在不同厚度的超薄氢化非晶硅(a-Si:H)膜内直接制备1D有序纳米硅(nc-Si)阵列.拉曼散射谱表明,样品上呈条状分布的受辐照区域发生晶化.原子力显微镜和透射电子显微镜测试结果表明：1D的nc-Si阵列的周期和移相光栅掩模一样.随着a-Si:H膜厚度从10nm降至4nm,通过控制激光的能量密度,每个周期中nc-Si条状分布区宽度可达到30nm.nc-Si条状分布区的高分辨电子显微镜照片显 关键词： 纳米硅 激光干涉结晶 移相光栅 定域晶化     

尺寸可控的纳米硅的生长模型和实验验证

基于经典热力学理论，对a-SiN_x/a-Si:H/a-SiN_x三明治结构或a-Si:H/a-SiN_x多层膜结构中纳米硅成核，以及从球形到鼓形的生长过程进行了研究. 建立了限制性晶化理论模型：在纳米硅生长过程中，由于界面能增大将导致生长停止，给出限制性晶化条件——a-Si:H子层厚度小于34 nm. 在激光晶化和常规热退火两种方法形成的a-SiN_x/nc-Si/a-SiN_x三明治结构和nc-Si/a-SiN_x多层膜结构中验证了该理论模型. 关键词： 非晶硅 纳米硅 激光辐照 结晶     

铜铁镁三掺铌酸锂晶体的第一性原理研究

利用基于密度泛函理论的第一性原理,研究了Cu:Fe:Mg:LiNbO3晶体及对比组的电子结构和光学特性.研究显示,单掺铜或铁铌酸锂晶体的杂质能级分别由Cu 3d轨道或Fe 3d轨道贡献,禁带宽度分别为3.45和3.42 eV;铜、铁共掺铌酸锂晶体杂质能级由Cu和Fe的3d轨道共同贡献,禁带宽度为3.24 eV,吸收峰分别在3.01,2.53和1.36 eV处;Cu:Fe:Mg:LiNbO3晶体中Mg^2+浓度低于阈值或高于阈值(阈值约为6.0 mol%)的禁带宽度分别为2.89 eV或3.30 eV,吸收峰分别位于2.45 eV,1.89 eV或2.89 eV,2.59 eV,2.24 eV.Mg^2+浓度高于阈值,会使吸收边较低于阈值情况红移;并使得部分Fe^3+占Nb位,引起晶体场改变,从而改变吸收峰位置和强度.双光存储应用中可选取2.9 eV作为擦除光,2.5 eV作为读取和写入光,选取Mg^2+浓度达到阈值的三掺晶体在增加动态范围和灵敏度等参量以及优化再现图像的质量等方面更具优势.     

Acoustic cavitation series: part one: Acoustic cavitation: an introduction

Acoustic cavitation has been an active area of research for at least 30 years and interest in the subject shows no sign of diminishing. Cavitation may occur whenever high intensity ultrasound is applied to liquids, for example in such important applications as sonar, industrial processing and bio-medical research. Future issues will carry a series of articles reviewing the physics and technology of acoustic cavitation, each contributed by a well-known specialist. The present introductory article is a preface to the series, covering background history, explaining the scope of the subject and defining terms in common use. Also included is a list of the major sources of reference presently available, in the form of books, reviews and collections of papers.     

The radiothermoluminescence of (ZnS:CdS:Ag:Ni:Co) phosphors irradiated with beta-rays

The radiothermoluminescence characteristics have been studied for a number of (ZnS:CdS::Ag:Ni:Co) phosphors, with various cobalt impurity contents, after exposure to⁹⁰Sr beta-rays at room temperature. Thermoluminescent spectra show a peak wavelength of 7000 Å, which remains unchanged with increase in cobalt concentration. Thermoluminescence curves exhibit a single well-defined peak appearing at temperatures far above room temperature. This peak shifts to lower temperatures with increasing cobalt content. The relation between thermoluminescence response and dose is linear over the dose range of 1 to 500 rads. Thermoluminescence measurements made after storing the irradiated phosphor for 48 hours in dark have revealed an information loss of 4% over this storage period. The radiothermoluminescence characteristics, storage capacity and storage stability of these sulphide phosphors compete reasonably with those of lithium fluoride over the dose range of 1 rad to 500 rads.     

Fourier transform profilometry: : a review

Fourier transform profilometry is one of the popular non-contact 3-D measurement methods, where a Ronchi grating or sinusoidal grating is projected onto a diffuse three-dimensional surface, and the resulting deformed grating image is detected by a CCD camera and processed by a computer. This method requires only one frame (or two frames) of the deformed fringe pattern in some algorithms to retrieve the surface of measured object, so it has obvious advantage for real time data acquisition and 3-D measurement of dynamic process. In this paper, we review some algorithms in FTP, discuss some important problems, including frequency spectra overlapping, phase unwrapping, sampling, and 3-D measurement of dynamic process. With the development of computer hardware and software and availability of high-resolution image grabber, FTP method will be a promising one for acquiring 3-D data of object, and more and more researchers pay attention to it.     

Er:YCOB和Er:Yb:YCOB晶体的光谱分析

分别测量了Er YCOB晶体和ErYb YCOB晶体的室温吸收光谱.讨论了Yb3+离子对Er3+离子的敏化作用.     

LiNbO_3:In:Fe:Cu晶体中的双波长非易失存储

为了提高晶体的非易失存储性能,采用双波长存储技术实验研究了LiNbO3:In:Fe:Cu晶体中的非易失存储,折射率调制度为1.04×10-4,记录灵敏度达到0.965 cm/J.与传统的双色非易失记录相比,该方法大幅度地提高了光栅的强度和记录的灵敏度.利用Kukhtarev带输运模型对双波长非易失记录过程中光栅的动态演化过程进行了数值模拟,同时讨论了氧化还原程度对双波长非易失全息记录的影响.理论与实验符合的较好.     

SILEX-I: 300-TW Ti:sapphire laser

Based on chirped pulse amplification technology, we have built a Ti:sapphire laser system, called SILEX-I (superintense laser for experiments on extremes), at CAEP, which consists of three stages with 5-, 30-, and 300-TW outputs, respectively. The first and the second stages work at 10 Hz, while the third works at single shot. Pulse durations of 30 fs have been obtained by installing an acousto-optic programmable dispersive filter (AOPDF) to compensate for the spectral gain narrowing in the regen. By taking a number of advanced measures for spatial beam control, such as spatial beam shaping, relay-imaged propagation, precise alignment of compressor gratings, and OAP, near-diffraction limited focal spots (FWHM) have been obtained. Focused intensities are calculated at (1–3) × 10²⁰ W/cm² with an f/2.2 OAP.SILEX-I has shown an excellent stability and reliability in operations for applications since its completion and will soon be able to operate at 500 TW.