Simulation of detection and scattering of sound waves by the lateral line of a fish

A solvable model of lateral line of a fish based on a wave equation with additional boundary conditions on a set of isolated points is proposed.Within the framework of this model it is shown that the ratio of pressures on lateral lines on different fish flanks,as well as the cross section of sound scattering on both the lines,strongly depends on angles of incidence of incoming sound waves.The strong angular dependence of the pressure ratio seems to be sufficient for the fish to determine the directions from which the sound is coming.     

Mitigation of the deleterious effect of silicon species on the conductivity of ceria electrolytes

The deleterious effect of silicon species on the conductivity of ceria electrolytes is well documented in the literature. A simple process has been developed at Praxair that alleviates the negative effect of high concentrations of silicon species on the conductivity of ceria electrolytes. The impact of this process on the conductivity of commercially available doped ceria electrolyte powders is demonstrated and a likely mechanism for the reduction of the resistivity is proposed. The influence of this process on other properties of the ceria electrolyte is discussed.     

Analysis of the features of meniscus profile curves during growth of base-faceted sapphire ribbons

The dependence of the step parameters on the surface of base-faceted sapphire ribbons on the angle of deviation of crystallographic orientation has been measured. A model of step formation on the lateral ribbon surface is proposed. Hysteretic character of the dependence of the lateral ribbon surface inclination on the meniscus angle at the triple point is shown. The shapes of the lateral surfaces are calculated and the range of variation in the meniscus angle is determined.     

小液滴撞击壁面传热特性数值分析

小液滴撞击壁面现象在喷雾冷却等领域都有广泛应用.为研究小液滴(微米)撞击热壁面(非沸腾区)传热过程,建立了二维液滴撞壁瞬态模型,并采用相场方法对小液滴换热过程中对流热通量和导热热通量的大小进行了对比.研究结果表明:液滴撞击壁面初期形成“冷斑”,有利于小液滴与壁面的传热;小液滴撞击壁面过程中热通量峰值存在于三相接触点附近,数量级在105—106 W/m²;小液滴撞击壁面过程中受壁面浸润性和液滴尺寸对传导热通量的影响较为显著,而速度和液滴尺寸对对流热通量的影响较为显著;大多数情况下,小液滴撞击壁面传导热通量数量级在103—105 W/m²,对流热通量数量级在104—106 W/m²,对流热通量大于传导热通量,在整个换热过程中占据主导地位.     

路堤倾角变化对高速列车侧风运行气动特性影响

采用计算流体力学方法,探讨路堤倾角变化对高速列车侧风运行气动特性影响.结果表明:随着路堤倾角增大,头车侧向力系数先增加后减小,而中间车侧向力系数则持续减小.尾车上的侧向力系数先是略微减小,当路堤倾角达到47.5°时,侧向力系数随倾角增加而增加.作用在中间车上的负升力随着路堤倾角增加而增加.尾车的升力系数对路堤倾角变化非常敏感,变化幅度较大.路堤倾角变化时高速列车绕流流场变化,从而导致列车受到的气动力发生变化.     

Influence of temperature change on column buckling of multiwalled carbon nanotubes

Based on theory of thermal elasticity mechanics, an elastic multiple column model is developed for column buckling of MWNTs with large aspect ratios under axial compression coupling with temperature change. In this model, each of the nested concentric tubes is regarded as an individual column and the deflection of all the columns is coupled together through the van der Waals interactions between adjacent tubes. The thermal effect is incorporated in the formulation. Following this model, an explicit expression is derived for the critical buckling strain for a double-walled carbon nanotube. The influence of temperature change on the buckling strain is investigated. It is concluded that the effect of temperature change on the buckling strain is dependent on the temperature changes, the aspect ratios, and the buckling modes of carbon nanotubes.     

Peculiarities of evaporation of a thin water layer in the presence of a solvable surfactant

Evaporation of a thin layer of a polar liquid (water) having a free surface and located on a solid substrate is investigated. A solvable surfactant is placed on the free liquid-vapor interface. The surface tension is a linear function of the surface concentration of the surfactant. The surface energy of the solid-liquid contact line is a nonmonotonic function of the layer thickness and is the sum of the Van der Waals interaction and the specific interaction of the double electric layer on the interface. The effect of the solvable surfactant on the dynamics and stability of the propagation of the evaporation front in the thin liquid film is analyzed in the long-wave approximation in the system of Navier-Stokes equations.     

�������ЧӦ�Ե�������Ӱ�����ֵ�о�

在考虑到捕获电子效应的情况下,对求解二维Fokker-Planck方程的编程进行了反弹平均的修改,使用了交替方向隐式法来求解方程。分析和计算了在不同扩散系数和不同共振区间的情况下,捕获电子效应对驱动电流的影响。结果显示：随着逆纵横比的增加驱动电流密度有明显的下降,在磁轴附近捕获电子效应对电流驱动影响很小;提高波功率并不能很好的改善捕获电子效应对电流驱动的影响;右移共振区间提高共振电子的速度,也不能很好的改善捕获电子效应对电流驱动的影响。所得结果与理论分析基本一致。     

Effect of plasma on combustion characteristics of boron

As it is very difficult to release boron energy completely, kinetic mechanism of boron is not clear, which leads to the lack of theoretical guidance for studying how to accelerate boron combustion. A new semi-empirical boron combustion model is built on the King combustion model, which contains a chemical reaction path; two new methods of plasma-assisted boron combustion based on kinetic and thermal effects respectively are built on the ZDPLASKIN zero-dimensional plasma model. A plasma-supporting system is constructed based on the planar flame, discharge characteristics and the spectral characteristics of plasma and boron combustion are analyzed. The results show that discharge power does not change the sorts of excited-particles, but which can change the concentration of excited-particles. Under this experimental condition,plasma kinetic effect will become the strongest at the discharge power of 40 W; when the discharge power is less than 40 W,plasma mainly has kinetic effect, otherwise plasma has thermal effect. Numerical simulation result based on plasma kinetic effect is consistent with the experimental result at the discharge power of 40 W, and boron ignition delay time is shortened by 53.8% at the discharge power of 40 W, which indicates that plasma accelerates boron combustion has reaction kinetic paths, while the ability to accelerate boron combustion based on thermal effect is limited.     

基底表面纳米织构对非晶四面体碳膜结构和摩擦特性的影响研究

本文利用离子束表面改性技术对基底表面进行不同时间的轰击, 形成不同规则的纳米织构, 对不同织构的变化规律进行了研究, 同时, 利用磁过滤真空阴极电弧技术, 在具有不同纳米织构的各基底上沉积相同时间的四面体非晶碳薄膜. 采用原子力显微镜对各基底的织构进行形貌分析, 结果表明, 高能粒子束的轰击对基底表面形貌有较大的影响, 根据离子束轰击时间的不同, 可以在基底表面形成各种不同规则的纳米织构, 轰击15 min后发现基底表面形成点阵纳米织构, 之后随着时间的增加, 基本维持点阵结构. 通过X射线光电子能谱仪和摩擦磨损试验仪对沉积在具有不同织构的基底上的ta-C薄膜进行测试, 研究表明, 基底表面纳米织构的非晶层结构引起薄膜内部sp³键的含量降低, 释放了薄膜的内应力, 同时发现基底表面纳米织构将ta-C薄膜磨损时间从不足10 min提高到约70 min, 有效提高了薄膜的耐磨性.     

LAMOST围挡通道的壁面传热影响分析

运用热分析软件Icepak对望远镜LAMOST的圆顶围挡通道进行了热计算与分析，重点分析了围挡壁面的热辐射和热传导对整个温度场的影响。在通风管道冷却方案的基础上，分别建立了壁面辐射和传导的热模型，描述了壁面的传热结构。仿真计算了增加壁面热辐射和热传导时主光学组件——焦面的温度场分布，并对此作了对比分析。数值计算与仿真结果表明：壁面传热对其内部温度场的影响不大;利用通风管道的冷却措施可将焦面的最大温度梯度控制在0.4℃／m；围挡的特性结构对传热有效。     

TDX-200透射电子显微镜自动曝光原理研究

通过分析透射电子显微镜的曝光机理,得出了荧光屏亮度与曝光时间之间的关系表达式。设计了TDX-200透射电子显微镜自动曝光电路,并通过实验对自动曝光参数进行了标定。通过对多种实际样品在不同工作模式下进行自动曝光试验,得到了相对清晰的电子显微像。结果表明,TDX-200透射电子显微镜自动曝光的设计满足要求。     

Discrete dislocation simulation of nanoindentation: the influence of obstacles and a limited number of dislocation sources

Nanoindentation is simulated on the computer by means of a 2D discrete dislocation model under the conditions of a constrained geometry. First, an indentation test near a grain boundary is investigated by the arrangement of only one boundary and second, an indentation test into the center of the surface of a small grain (lamella) is mimicked by the arrangement of two boundaries. The effect of a limited number of dislocation sources is studied by the simulations of an indentation test in a plastically deformable film on an ideal elastic substrate and by such tests on an ideal elastic film on a plastically deformable substrate. The discrete nature of plasticity is shown to have a significant influence on the mechanical material behavior in all our investigations.     

Calculation of the Thermal Resistance of a Heat Distributer in the Cooling System of a Heat-Loaded Element

Numerical simulation is performed for heat transfer in a heat distributer of a thermoelectric cooling system, which is located between the heat-loaded element and the thermoelectric module, for matching their sizes and for heat flux equalization. The dependences of the characteristic values of temperature and thermal resistance of the copper and aluminum heat distributer on its thickness and on the size of the heatloaded element. Comparative analysis is carried out for determining the effect of the thermal conductivity of the material and geometrical parameters on the heat resistance. The optimal thickness of the heat distributer depending on the size of the heat-loaded element is determined.     

Filamentation length of ultrashort laser pulse in presence of aerosol layer

Filamentation behavior of femtosecond laser pulses in the air in presence of aerosol on the optical path is simulated numerically on basis of (3D + 1)-dimensional nonlinear Schrödinger equation. The effect of a localized attenuating layer modeling an aerosol medium, on spatial extension and evolution of the light filament is investigated. For the first time, it is shown that filamentation length depends not only on the optical depth of the aerosol layer and pulse peak power, but also on aerosol location on the propagation path and its spatial extension along the beam. The length of the filament is maximal if the nonlinear focus of the beam is located behind the aerosol layer rather than before it.     

Calculation of diffraction by strongly elongated bodies of revolution

An approach to construct approximations for the diffracted field on the surface of strongly elongated bodies is suggested. The approach is based on high-frequency asymptotic decomposition which is constructed under the supposition that transverse curvature of the surface is asymptotically large. Leading order terms of asymptotic decompositions for the fields diffracted by spheroid, one-sheeted and two-sheeted hyperboloids and on narrow cone are derived.     

共面线多阳极大面积光电倍增管的研制

提出了一种新型的基于共面线结构的多阳极光电倍增管(CPWMA-PMT),可实现大的工作面积、反射式光电阴极和近贴式聚焦方式。阐述了CPWMA-PMT的工作原理,分析了设计与研制中的关键问题。对所研制的CPLMA-PMT进行了参量测试,验证了在近贴聚焦工作条件下采用共面线多阳极结构的可行性,并提出了进一步的改进方向。     

金刚石薄膜负偏压形核的边缘效应

 在微波等离子体化学气相沉积装置中，研究了金刚石薄膜在Si (100)面上的负偏压形核行为，结果表明，偏压大小对金刚石的形核均匀性有显著影响，而甲烷浓度主要影响形核时间，对金刚石的最大核密度影响不大。在硅片尺寸小于钼支撑架时，形核行为存在明显的边缘效应，即在偏压值低于-150 V时，硅片边缘金刚石核密度急剧降低，远低于硅片中央；在甲烷浓度比较低时，硅片边缘核密度要高于中间。研究表明，造成这种现象的主要原因是硅片下的钼支撑架发射电子所致，过量的原子H对金刚石的形核是不利的。