核/壳结构ZnS : Mn/CdS纳米粒子的制备及发光

利用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS : Mn),利用沉淀法对ZnS ∶ Mn纳米粒子进行了不同厚度的CdS无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及光致发光(PL)光谱等手段对样品进行了表征。TEM显示粒子为球形,直径大约在14~18 nm之间。由XRD结果可以看出CdS壳层的形成过程受到了ZnS ∶ Mn核的影响,导致其结晶较差。XRD和XPS测量证明了ZnS : Mn/CdS的核壳结构。随着CdS壳层的增厚,样品的发光强度呈现一直减弱的现象。     

核/壳结构的ZnS:Mn/SiO_2纳米粒子的制备及发光性质研究

采用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS∶Mn),然后利用正硅酸乙酯(TEOS)的水解反应对其进行了不同厚度的SiO2无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及荧光发射光谱(PL)对样品的结构及光学性质进行了表征和研究。包覆SiO2壳层后,粒子的粒径明显增大并且在ZnS∶Mn纳米粒子表面可以观察到明显的SiO2壳层。XPS测试印证了ZnS∶Mn/SiO2的核壳结构。随着SiO2壳层的增厚,ZnS∶Mn/SiO2的Mn离子的发光先增强后减弱,这是因为SiO2壳层同时具有表面修饰和降低发光中心浓度这两种相反的作用。当壳层厚度(壳与核的物质的量的比)达到5时,发光效果达到最好,其强度达到未包覆样品的7.5倍。     

CdSe/CdS核/壳型纳米晶的光谱特性

以巯基乙酸为稳定剂制备了CdSe/CdS核／壳型纳米晶。用光吸收谱（Abs)、光致发光谱（PL）及光致发光激发谱（PLE）研究了CdS壳层对CdSe纳米晶电子结构，从而对其吸收和发光性能的影响。根据PL和PLE的结果以及带边激子精细结构的计算结果，我们用尺寸很小的纳米晶中所形成的基激缔合物解释了PL光谱与吸收边之间较大的Stokes位移。     

核壳型ZnS∶Cu/ZnS量子点的制备及发光性质

本文采用水相合成方法制备了ZnS∶Cu量子点并进行了ZnS壳层修饰,研究了壳层厚度对ZnS∶Cu量子点光学性质的影响,采用TEM、XRD、PL、PLE和UV-Vis等测试方法对其进行了表征。实验结果表明,合成的ZnS∶Cu/ZnS量子点为立方闪锌矿,尺寸分布均匀呈球形,分散性良好,经过壳层修饰平均粒径由2 nm增加到3.2 nm。随着ZnS壳与ZnS核量的比的增加,量子点的PLE激发峰位置和UV-Vis吸收谱线出现红移,也说明了量子点的尺寸增大,证明ZnS在ZnS∶Cu量子点的表面生长,形成了核壳结构的ZnS∶Cu/ZnS量子点。随着壳层增厚,量子点与铜离子发光中心相关的发射峰强度先增大后减小,当壳核比n_s/n_c=2.5时,发光强度达到最大。     

Ag-Au二元纳米微粒吸收谱的计算

纳米微粒的光学性能与其表面等离子体共振关系密切.本文利用推广的Mie理论计算研究了Au-Ag体系单质、合金以及核壳结构纳米颗粒的消光、吸收和散射的性能(包括壳核结构Ag-Au微粒在紫外-可见光的吸收性能),计算结果与实验值相符合得很好.研究表明,随着粒径的增加,微粒表面等离子体共振偶极吸收峰出现红移,波峰位置与纳米微粒的尺寸具有线性关系.壳核结构中,粒径与核壳比决定了整个微粒的吸收性能.进一步研究表明,当Au壳层较薄时,可以获得具有可调光学性能的壳核纳米结构;而当Au壳层较厚时,其光学性能与同尺寸单质Au微粒一致.通过计算分析,本文还将Mie理论推广到具有空腔结构并且壳层厚度达到一定值的纳米微粒.另外,研究发现合金结构纳米微粒的吸收峰位置与合金成分有着线性关系.本研究表明,人们可以通过控制纳米微粒的尺寸、形貌和结构,调节其表面等离子体共振峰位,这大大拓展了纳米微粒的应用范围.     

CdSe/CdS核壳纳米晶微波水热法一步合成与发光光谱分析

采用微波水热法一步合成了核壳结构的CdSe/CdS纳米晶,讨论了巯基丙酸中S^2-的释放过程对纳米晶生长的影响。XRD和Raman光谱结果表明,140℃合成温度下获得了CdSe/CdS核壳结构的纳米晶。FTIR光谱结果表明,巯基丙酸随时间的分解有助于CdS壳层的形成。PL光谱呈现出CdSe纳米晶的带间发射和缺陷发射,随着核壳结构的形成,CdSe纳米晶的表面缺陷被抑制,相关的荧光发射减弱。     

ZnSe:Cu/CdS核壳量子点的合成及光学性能研究

以CdS为壳层材料对核水溶性ZnSe:Cu量子点进行包覆,得到ZnSe:Cu/CdS核壳结构的量子点。研究了壳层厚度对ZnSe:Cu量子点光学性能的影响,采用TEM、XRD、PL和UV-Vis手段对所得样品进行表征。实验结果表明:量子点为立方闪锌矿结构,分散性好,形状为球形,经壳层修饰后量子点的粒径由2.7 nm增大到4.0 nm。随着包覆CdS壳层数的增加,量子点的发射和紫外吸收谱红移,说明量子点在长大,证明CdS壳层生长在ZnSe:Cu量子点的表面,形成了核壳结构的ZnSe:Cu/CdS量子点。包覆CdS壳层后ZnSe:Cu量子点的发光强度减弱,但稳定性得到了提高。     

核-壳结构的ZnS:Cu/ZnS纳米粒子的制备及发光性质研究

制备了核-壳结构的ZnS:Cu/ZnS纳米粒子以及普通的没有壳的Cu2 掺杂的ZnS纳米粒子,研究了ZnS无机壳层对ZnS:Cu纳米粒子发光性质的影响.透射电子显微镜、激发光谱和发射光谱的研究表明,后加入的Zn2 离子在已经形成的ZnS核表面生长,形成ZnS壳层;而适当厚度的ZnS壳层可以钝化粒子表面,减少无辐射复合中心的数目,抑制表面态对发光的不利影响,提高ZnS:Cu纳米粒子中Cu2 离子在450 nm左右的发光强度.     

单核/双壳结构CdSe/CdS/ZnS纳米晶的合成与发光性质

以巯基乙酸为稳定剂,在水溶液中合成了单核/双壳结构的CdSe/CdS/ZnS纳米晶。在内核CdSe和外壳ZnS之间的内壳CdS作为晶格匹配调节层,能够很好的改善核/壳界面处的性能,而且,最外层ZnS能够最大程度地使激子受限。用TEM和XPS对纳米晶进行了表征,并且用光致发光光谱和吸收光谱对不同核壳结构的纳米晶的发光性能进行了比较,结果表明单核/双壳结构的纳米晶具有更加优异的发光特性。     

核-壳结构的ZnS∶Cu/ZnS纳米粒子的制备及发光性质研究

制备了核-壳结构的ZnS∶Cu/ZnS纳米粒子以及普通的没有壳的Cu2 掺杂的ZnS纳米粒子,研究了ZnS无机壳层对ZnS∶Cu纳米粒子发光性质的影响。透射电子显微镜、激发光谱和发射光谱的研究表明,后加入的Zn2 离子在已经形成的ZnS核表面生长,形成ZnS壳层;而适当厚度的ZnS壳层可以钝化粒子表面,减少无辐射复合中心的数目,抑制表面态对发光的不利影响,提高ZnS∶Cu纳米粒子中Cu2 离子在450 nm左右的发光强度。     

Characterization of semiconductor core-shell nanoparticles by resonant Raman scattering and photoluminescence spectroscopy

Colloidal CdSe nanoparticles (NPs), passivated with CdS and ZnS, were characterized by resonant Raman scattering and photoluminescence (PL). The effect of the passivating shell, its volume and formation procedure on optical and vibrational spectra is discussed. Analyzing the Raman peaks due to optical phonons inside the core and those related to the core-shell interface allows some understanding of the relation between the core-shell structure and its PL properties to be achieved. In particular, a compositional intermixing at the core/shell interface of the NPs was deduced from the Raman spectra, which can noticeably affect their PL intensity.     

Synthesis and characterization of aqueous MPA-capped CdS–ZnS core–shell quantum dots

The novel CdS–ZnS core–shell nanoparticles are synthesized using simple one-step aqueous chemical approach. 3-mercaptopropionic acid (MPA) was used as the capping molecule. The structural and optical properties of the prepared samples are characterized by X-ray diffraction (XRD), UV–vis absorption spectroscopy, photoluminescence (PL) spectroscopy, energy-dispersive X-ray (EDX) and transition electron microscopy (TEM). The studies show that pH contributed noticeably to the growth and optical properties of nanoparticles. The TEM results indicate that the prepared particles have core–shell structure.     

Synthesis and stabilization of ZnS nanoparticles embedded in silica nanospheres

The silica-coated ZnS nanocomposites have been synthesized by a seeded-growth procedure in iso-propanol. The results of XRD, HRTEM and UV absorption show that the ZnS nanoparticles can be incorporated in the silica nanospheres without changing the particle size, and the composites are of multi-core structure. UV absorption and emission spectra have been performed to check the character of the composites, which show that the silica shell not only increases the PL intensity, but also greatly improves the anti-oxidation ability and thermal stability. PACS 81.05.Dz; 81.16.Be; 81.65.Rv; 78.55.Et; 78.66.Hf     

水溶性CdTe/CdS纳米晶表面SiO2壳层的反相胶束法包覆

"提出了一种水相中制备CdTe/CdS核壳结构纳米粒子的方法.用Te粉作为碲源,用Na2S作为硫源,在50 ℃下制备了CdTe/CdS核壳结构纳米粒子. 用紫外可见吸收光谱和荧光光谱分析了CdS壳层对CdTe核的影响. 随CdS壳层厚度的增加,紫外可见吸收光谱和荧光光谱均发生了红移. CdS壳层厚度较薄时,CdTe/CdS纳米晶的荧光强度较CdTe纳米粒子有显著提高;而CdS壳层厚度较厚时,CdTe/CdS纳米晶的荧光强度会逐渐降低. 用反相胶束法在CdTe/CdS核壳结构纳米粒子的表面包被一层SiO2,     

CdS/ZnS core–shell nanoparticles in arachidic acid LB films

Core–shell CdS/ZnS nanoparticles in arachidic acid film were prepared through a novel Langmuir–Blodgett (LB) approach. Post-deposition treatment of the precursor LB multilayers of cadmium arachidate with H₂S gas followed by intercalation of Zn²⁺ ions and further sulfidation result in the formation of CdS/ZnS nanoparticles in the LB film. The formation of these nanoparticles and resulting changes in layered structures were studied by FTIR and X-ray reflection measurements. The optical properties were studied using UV–vis absorption and photoluminescence spectroscopy. A red-shift in the absorption spectrum and enhancement of CdS excitonic emission together with reduction of surface states emission suggest that after the intercalation step, a thin layer of ZnS surrounds the CdS nanoparticles, thus forming a core–shell structure. Subsequent to the second sulfidation, a further red-shift in absorption suggests the formation of a thicker ZnS coating on CdS. Electron diffraction of CdS nanoparticles coated with thicker ZnS showed the diffraction patterns of only ZnS, as expected for core–shell structures.     

Structural and optical properties of monodispersed ZnS/CdS/ZnO and ZnO/ZnS/CdS nanoparticles

Excellent luminescence properties of ZnS/CdS/ZnO and ZnO/ZnS/CdS nanocrystallites synthesized through a simple chemical method at room temperature are reported. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), UV–visible absorption and photoluminescence techniques were used to characterize the undoped ZnS, CdS and ZnO and the novel ZnS/CdS/ZnO and ZnO/ZnS/CdS nanoparticles. The optical properties of ZnS/CdS/ZnO and ZnO/ZnS/CdS nanoparticles reflect a combinational effect of the photoluminescent properties of ZnS, CdS and ZnO.