Structural,vibrational study and superprotonic behavior of a new mixed dipotassium hydrogenselenate dihydrogenphosphate K2(HSeO4)1.5(H2PO4)0.5

Ongoing studies of the KHSeO₄–KH₂PO₄ system aiming at developing novel proton conducting solids resulted in the new compound K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (dipotassium hydrogenselenate dihydrogenphosphate). The crystals were prepared by a slow evaporation of an aqueous solution at room temperature. The structural properties of the crystals were characterized by single-crystal X-ray analysis: K₂(HSeO₄)_1.5(H₂PO₄)_0.5 (denoted KHSeP) crystallizes in the space group P 1¯ with the lattice parameters: a = 7.417(3) Å, b = 7.668(2) Å, c = 7.744(5) Å, α = 71.59(3)°, β = 87.71(4)° and γ = 86.04(6)°. This structure is characterized by HSeO₄⁻ and disordered (H_xSe/P)O₄⁻ tetrahedra connected to dimers via hydrogen bridges. These dimers are linked and stabilized by additional hydrogen bonds (O–H–O) and hydrogen bridges (O–H…O) to build chains of dimers which are parallel to the [0, 1, 0] direction at the position x = 0.5.The differential scanning calorimetry diagram showed two anomalies at 493 and 563 K. These transitions were also characterized by optical birefringence, impedance and modulus spectroscopy techniques. The conductivity relaxation parameters of the proton conductors in this compound were determined in a wide temperature range. The transport properties in this material are assumed to be due to H⁺ protons hopping mechanism.     

Synthesis,crystal structure,spectroscopic characterization and optical properties of bis(4-acetylanilinium) tetrachlorocobalt (II)

The chemical preparation, crystal structure, spectroscopic investigations and optical features are given for a novel organic–inorganic hybrid material [C₈H₁₀NO]₂CoCl₄.The compound is crystallized in the orthorhombic space group Cmca, with the following unit cell parameters: a=19.461(2) Å, b=15.523(2) Å, c=13.7436(15) Å, and Z=8. The atomic arrangement shows an alternation of organic and inorganic layers along the b-axis. The cohesion between these entities is performed by N–H…Cl and N–H…O hydrogen bonds and π–π stacking interactions.Infrared and Raman spectra at room temperature are recorded in the 4000−400 and 4000−0 cm⁻¹ frequency regions, respectively and analyzed on the basis of literature data. This study confirms the presence of the organic cation [C₈H₁₀NO]⁺ and of the [CoCl₄]²⁻ anion. UV–vis spectroscopy results showed the indirect transition with band gap energy 2.98 eV.     

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3−δ measured by in situ neutron diffraction

The phase stability, oxygen stoichiometry and expansion properties of SrCo_0.8Fe_0.2O_3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5 × 10^− 4 to 1 atm. At a pO₂ of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across the whole temperature range investigated. At a pO₂ of 10^− 1 atm, a two-phase region exists below 922 K, where the cubic perovskite phase coexists with a vacancy ordered brownmillerite phase, Sr₂Co_1.6Fe_0.4O₅, space group Icmm. A pure brownmillerite phase is present at pO₂ of 10^− 2 and 5 × 10^− 4 atm below 1020 K. Above 1020 K, the brownmillerite phase transforms to cubic perovskite through a two-phase region with no brownmillerite structure observed above 1064 K. Large distortion of the BO₆ (B = Co, Fe) octahedra is present in the brownmillerite structure with apical bond lengths of 2.2974(4) Å and equatorial bond lengths of 1.9737(3) Å at 1021 K and a pO₂ of 10^− 2 atm. SCF is highly oxygen deficient with a maximum oxygen stoichiometry, 3 − δ, measured in this study of 2.58(2) at 873 K and a pO₂ of 1 atm and a minimum of 2.33(2) at 1173 K and a pO₂ of 5 × 10^− 4 atm. Significant differences in lattice volume and expansion behavior between the brownmillerite and cubic perovskite phases suggest potential difficulties in thermal cycling of SrCo_0.8Fe_0.2O_3−δ membranes.     

Super-protonic phase transition and fast ionic conductivity of Li+ in [Li0.2(NH4)0.8]2TeCl6

The differential scanning calorimetry diagram of [Li_0.2(NH₄)_0.8]₂TeCl₆ showed one anomaly at 526 K accompanied with a shoulder at 505 K.The conductivity plot exhibits two anomalies at 496 and 526 K, which characterize the beginning and the end of the crossing to superionic conductor state. The low temperature conduction is ensured essentially by Li⁺. A sudden jump confirms the presence of a superionic protonic transition related to the fast motion of Li⁺ and H⁺ ions. Above 526 K, the high temperature phase is characterized by high electrical conductivity (10^− 3 Ω^− 1 m^− 1) and low activation energy (E_a < 0.3 eV).The dielectric constant evolution as a function of frequency and temperature revealed the same anomaly.Transport properties in this material appear to be due to Li⁺ and H⁺ ions' hopping mechanism.     

Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

Hydrophilic polyaniline nanofibrous architecture using electrosynthesis method for supercapacitor application

An electrosynthesis process of hydrophilic polyaniline nanofiber electrode for electrochemical supercapacitor is described. The TGA–DTA study showed polyaniline thermally stable up to 323 K. Polyaniline nanofibers exhibit amorphous nature as confirmed from XRD study. Smooth interconnected fibers having diameter between 120–125 nm and length typically ranges between 400–500 nm observed from SEM and TEM analysis. Contact angle measurement indicated hydrophilic nature of polyaniline fibers. Optical study revealed the presence of direct band gap with energy 2.52 eV. The Hall effect measurement showed room temperature resistivity ∼3 × 10⁻⁴ Ω cm and Hall mobility 549.35 cm⁻²V⁻¹ s⁻¹_. The supercapacitive performance of nanofibrous polyaniline film tested in 1 M H₂SO₄ electrolyte and showed highest specific capacitance of 861 F g⁻¹ at the voltage scan rate of 10 mV/s.     

Mixed conductivity,stability and thermomechanical properties of Ni-doped La(Ga,Mg)O3−δ

Perovskite-type LaGa_0.65Mg_0.15Ni_0.20O_3−δ exhibiting oxygen transport comparable to that in K₂NiF₄-type nickelates was characterized as a model material for ceramic membrane reactors, employing mechanical tests, dilatometry, oxygen permeability and faradaic efficiency measurements, thermogravimetry (TG), and determination of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10^− 15 Pa to 40 kPa. Within the phase stability domain which is similar to La₂NiO_4+δ, the defect chemistry of LaGa_0.65Mg_0.15Ni_0.20O_3−δ can be adequately described by the ideal solution model with oxygen vacancies and electron holes to be the only mobile defects, assuming that Ni²⁺ may provide two energetically equivalent sites for hole location. This assumption is in agreement with the density of states, estimated from thermopower, and the coulometric titration and TG data suggesting Ni⁴⁺ formation in air at T < 1150 K. The hole conductivity prevailing under oxidizing conditions occurs via small-polaron mechanism as indicated by relatively low, temperature-activated mobility. The ionic transport increases with vacancy concentration on reducing p(O₂) and becomes dominant at oxygen pressures below 10^− 7–10^− 5 Pa. The average thermal expansion coefficients in air are 11.9 × 10^− 6 and 18.4 × 10^− 6 K^− 1 at 370–850 and 850–1270 K, respectively. The chemical strain of LaGa_0.65Mg_0.15Ni_0.20O_3−δ ceramics at 1073–1123 K, induced by the oxygen partial pressure variations, is substantially lower compared to perovskite ferrites. The flexural strength determined by 3-point and 4-point bending tests is 167–189 MPa at room temperature and 85–97 MPa at 773–1173 K. The mechanical properties are almost independent of temperature and oxygen pressure at p(O₂) = 1–2.1 × 10⁴ Pa and 773–1173 K.     

Optical and physical characteristics of In-doped ZnO nanorods

In this paper the effect of indium dopants on structure, optical, electrical and mechanical properties of ZnO nanorods are studied. The average surface potentials and the surface currents of ZnO:In nanorods were 0.25–0.84 mV and 2.2–200 MΩ-cm, respectively. The turn-on threshold field for the vertical ZnO nanorods was around 2–16 V μm⁻¹. Emission current densities of 3.3–911.4 mA cm⁻² were obtained for an electrical field of 60–160 V μm⁻¹. The photoluminescence (PL) spectrum measured at 15–300 K showed that the intensity of the peak at 2.06 eV increased with decreasing temperature, while the peak at 2.06 eV further red shifted and the peak at 3.39 eV blue shifted.     

Proton dynamics in Cs3(HSO4)2(HPO4) studied by 1H NMR

Proton dynamics in Cs₃(HSO₄)₂(H₂PO₄) has been studied by means of ¹H solid-state NMR as well as thermal analyses. The thermal analysis shows an endothermic peak at 408 K, which corresponds to a superprotonic transition. Above the transition temperature a mass loss is observed in a dry atmosphere, which is easily recovered in a conventional dry atmosphere below the transition temperature. The ¹H magic-angle-spinning NMR spectra at room temperature show two peaks at 13.5 and 15.8 ppm, and a shoulder at 11.3 ppm from tetramethylsilane, demonstrating a presence of several inequivalent proton sites. Translational diffusion of protons takes place in both a room-temperature phase (RT) and a high-temperature phase (HT). In both phases reorientation of the SO₄/PO₄ tetrahedron limits the rate of the proton transport. The ¹H mean residence times are estimated as E_a = 33 kJ mol^− 1 and τ₀ = 0.97 × 10^− 9 s for phase RT from the second moment analysis and as E_a = 20 kJ mol^− 1 and τ₀ = 5.0 × 10^− 12 s for phase HT from the analysis of the ¹H T₁ results.     

Mid-infrared InAsSb-based nBn photodetectors with AlGaAsSb barrier layers – Grown on GaAs,using an interfacial misfit array,and on native GaSb

InAsSb-based nBn photodetectors were fabricated on GaAs, using the interfacial misfit (IMF) array growth mode, and on native GaSb. At −0.1 V operating bias, 200 K dark current densities of 1.4 × 10⁻⁵ A cm⁻² (on GaAs) and 4.8 × 10⁻⁶ A cm⁻² (on GaSb) were measured. At the same temperature, specific detectivity (D^*) figures of 1.2 × 10¹⁰ Jones (on GaAs) and 7.2 × 10¹⁰ Jones (on GaSb) were calculated. Arrhenius plots of the dark current densities yielded activation energies of 0.37 eV (on GaAs) and 0.42 eV (on GaSb). These values are close to the 4 K bandgap of the absorption layers (0.32–0.35 eV) indicating diffusion limited dark currents and small valence band offsets. Significantly, these devices could be used for mid-infrared focal plane arrays operating within the temperature range of cost-effective thermoelectric coolers.     

Vibrational study,phase transitions and electrical properties of 4-benzylpyridinium monohydrogenselenate

The title compound C₆H₅CH₂C₅H₄NH⁺·HSeO₄⁻ crystallizes in the orthorhombic system with the space group Pbca and the following unit cell dimensions: a=27.449(5) Å; b=10.821(6) Å and c=8.830(1) Å.The structure consists of infinite parallel two-dimensional planes built of HSeO₄⁻ anions and C₆H₅CH₂C₅H₄NH⁺ cations mutually.Differential scanning calorimetry study on 4-benzylpyridinium monohydrogen-selenate was carried out. A high temperature second order phase transition at 363 K was found and characterized by electric measurements. The Raman of polycrystalline sample has been recorded at different temperature between 297 and 373 K.The conductivity relaxation parameters associated with some H⁺ conduction have been determined from an analysis of the M′′/M′′_max spectrum measured in a wide temperature range. An appearance of the superionic phase transition in 4-BSe is closely related to a liberation or even a rotation increase of HSeO₄⁻ groups with heating.     

Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

Femtosecond electron dynamics on solid surfaces probed by low energy ion scattering and stimulated desorption of secondary ions

The cations emission from condensed matter surfaces has been investigated on the basis of localization and delocalization of valence hole(s) in the femtosecond timescale. The yield of scattered H⁺ (E₀=100 eV), though negligibly small from the Pt(1 1 1) substrate, increases markedly when Ar is adsorbed on it, indicating the localization of a valence (H⁺ 1s) hole on the physisorbed Ar layer. However, the yield of H⁺ scattered from a thick H₂O layer is considerably small relative to that from Ar and CO layers. The delocalized nature of a valence hole in water ice is caused by some covalency in hydrogen bonds. Hydrated protons, H⁺(H₂O)_n, n=1,2,…,10, are emitted efficiently in electron stimulated desorption from water molecules adsorbed on the Ar layer; the ion yields are highest at the initial adsorption stage and decay steeply with increasing coverage. Coulombic repulsion between the hydrated protons confined in physisorbed nanoclusters is responsible for the explosive ion emission.     

Electrical and dielectric properties of β-BaB2O4 (BBO) and CsLiB6O10 (CLBO) crystals

In barium borate (BBO) crystals, sodium and potassium ions, inherited due to the preparation technique, are dominant charge carriers. The conductivity between layers is higher; the conductivity activation energy and the conductivity at 350 °C being equal to 1.01±0.05 eV and (1.3±0.2)×10⁻⁸ S/cm, respectively. The conductivity activation energy and the conductivity at 350 °C along the channels are equal to 1.13±0.05 eV and to (4±0.2)×10⁻⁹ S/cm, respectively. Relative static permittivity is almost isotropic, and equal to 7.65±0.05. Upon storing of cesium–lithium borate (CLBO) crystals, pre-heating to 600 °C eliminates the influence of surface humidity. At 500 K, the ionic conductivity ranges from 4×10⁻¹² to 2×10⁻¹⁰ S/cm; the conductivity activation energy ranges from 1.01 to 1.17 eV. Relative static permittivity is equal to 7.4±0.3.     

Rapid synthesis of LiCr0.15Mn1.85O4 by glycine–nitrate method

LiCr_0.15Mn_1.85O₄ spinel has been successfully synthesized by glycine–nitrate method (GNM). The presence of pure spinel phase was confirmed by long term XRPD measurements and the Rietveld structural refinement. Lattice parameter was estimated to be 8.2338 Å. Average particle size of prepared powder material is below 500 nm. The BET surface area is 9.6 m² g^− 1. As a cathode material for lithium batteries LiCr_0.15Mn_1.85O₄ shows initial discharge capacity of 110 mA h g^− 1 and capacity retention of 83% after 50 cycles.     

Structural and optical properties of La-doped BaSnO3 thin films grown by PLD

In this study the structural and optical properties of lanthanum-doped BaSnO₃ powder samples and thin films deposited on fused silica were investigaed using laser ablation. Under an oxygen pressure of 5×10⁻⁴ mbar, phase pure BaSnO₃ films with a lattice constant of 0.417 nm and grain size of 21 nm were prepared at 630 °C. The band gap of BaSnO3 powder sample and thin films was calculated to be 3.36 eV and 3.67 eV, respectively. There was a progressive increase in conductivity for thin films of BaSnO₃ doped with 0~7 at% of La. The highest conductivity, 9 Scm⁻¹, was obtained for 7 at% La-doped BaSnO₃. Carrier concentration, obtained from Burstein-Moss (B-M) shift, nearly matches the measured values except for 3 at% and 10 at% La-doped BaSnO₃ thin films.     

Molybdenum carbide nano-sheet as a high capacity anode material for monovalent alkali metal-ion batteries—Theoretical investigation

This contribution presents a theoretical investigation of monovalent metal-ion adsorption and diffusion on two-dimensional (2D) buckled nanostructure of molybdenum carbide (MoC) by using the first principle method. We find that buckled MoC nanostructure exhibits great stability, semiconducting electronic property, and high performance as electrode material. Interestingly, Crystal Orbital Hamilton population (COHP) method results show that buckled MoC is chemically stable in a wide range of temperatures, and various Li, Na, ions adsorbed configurations, which is beneficial for anode materials. Especially, single-layer MoC exhibits a superior theoretical capacity of 993.16 mA h g⁻¹ for Li-ions and 496.58 mA h g⁻¹ for Na/K-ions. The storage capacity of 1200 mA h g⁻¹ is found for the adsorption of ions on multilayer bulk MoC. Moreover, migration energy barriers are predicted as 0.38 eV for Li, 0.32 eV for Na, and 0.24 eV for K; these remarkable results determine the applicability of buckled MoC as ideal anode material for metal-ion battery applications.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Bulk and surface properties of ionic salt CsH5(PO4)2

We report a comparative study of transport and thermodynamic properties of single-crystal and polycrystalline samples of the ionic salt CsH₅(PO₄)₂ possessing a peculiar three-dimensional hydrogen-bond network. The observed potential of electrolyte decomposition ≈ 1.3 V indicates that the main charge carriers in this salt are protons. However, in spite of the high proton concentration, the conductivity appears to be rather low with a high apparent activation energy E_a ≈ 2 eV, implying that protons are strongly bound. The transport anisotropy though is not large, correlates with the crystal structure: the highest conductivity is found in the [001] direction (σ_130 °C ∼ 5.6 × 10^− 6 S cm^− 1) while the minimal conductivity is in the [100] direction (σ_130 °C ∼ 10 ⁻⁶ S cm^− 1). The conductivity of polycrystalline samples appears to exceed the bulk one by 1–3 orders of magnitude with a concomitant decrease of the activation energy (E_a ≈ 1.05 eV), which indicates that a pseudo-liquid layer with a high proton mobility is formed at the surface of grains. Infrared and Raman spectroscopy used to study the dynamics of the hydrogen-bond system in single-crystal and polycrystalline samples have confirmed the formation of such a modified surface layer in the latter. However, no bulk phase transition into the superionic disordered phase is observed in CsH₅(PO₄)₂ up to the melting point T_melt ∼ 151.6 °C, in contrast to its closest relative compound CsH₂PO₄.     

First principles study of the structure,electronic state and stability of AlnAsm− anions

Structural and electronic properties of semiconductor binary microclusters Al_nAs_m⁻ anions have been investigated using the B3LYP-DFT method in the ranges of n = 1,2 and m = 1–7. Full structural optimization, adiabatic electron affinities calculation and frequency analysis are performed with the basis of 6–311 + G(d). The charged-induced structural changes in these anions have been discussed. The strong As–As bond is also favored over Al–As bonds in the Al_nAs_m⁻ anions in comparison with corresponding neutral cluster. Among different AlAs_m⁻ and Al₂As_m⁻ (m = 1–7) anions, AlAs₄⁻ and Al₂As₃⁻ are most stable.