Design and performance of an open jet wind tunnel for aero-acoustic measurement

This paper presents the design and performance of an open jet, blow down wind tunnel that was newly commissioned in the anechoic chamber at the ISVR, University of Southampton, UK. This wind tunnel is intended for the measurement of airfoil trailing edge self-noise but can be extended to other aeroacoustic applications. With the primary objectives of achieving acoustically quiet and low turbulence air jet up to 120 m/s through a 0.15 m × 0.45 m nozzle, several novel noise and flow control techniques were implemented in the design. Both the acoustical and aerodynamic performances of the open jet wind tunnel were examined in detail after its fabrication. It is found that the background noise of the facility is adequately low for a wide range of exit jet velocity. The potential core of the free jet is characterized by a low turbulence level of about 0.1%. Benchmark tests by submerging a NACA0012 airfoil with tripped and untripped boundary layers at 0° and 10° angles of attack respectively into the potential core of the free jet were carried out. It was confirmed that the radiating airfoil trailing edge self-noise has levels significantly above the rig noise over a wide range of frequencies. The low noise and low turbulence characteristics of this open jet wind tunnel are comparable to the best facilities in the world, and for its size it is believed to be the first of its kind in the UK.     

Design and performance of a small-scale aeroacoustic wind tunnel

The D5 aeroacoustic wind tunnel at Beihang University is a newly commissioned small-scale closed-circuit wind tunnel with low turbulence intensity and low background noise. The wind tunnel is built to study both aerodynamic and aeroacoustic performance of aircraft components or scaled models. The wind tunnel has two types of test sections, the closed type test section is used for aerodynamic tests while the open type test section is mainly used for aeroacoustic experiments. Both types of test section are 1 m in height and 1 m in width, and the maximum wind velocity in the test section can be up to 80 m/s. An anechoic chamber is built surrounding the test section to provide the non-reflecting condition. This paper provides an overview of design criteria and performance of the small-scale wind tunnel. The layout of the wind tunnel and some critical design treatments to improve aerodynamic and acoustic performance are discussed in detail. Some experiments are conducted to verify the performance of D5 wind tunnel, results confirm that the turbulence intensity is less than 0.08% in the core of test section and the background noise is comparable with other aeroacoustic wind tunnels. A scaled simplified nose landing gear model is also measured as a benchmark test, results reveal that noise radiated from the model is adequately higher than the background noise for a wide frequency range and remarkably consistent with other results from literatures.     

In-flight simulation experiments on turbulent jet mixing noise

The effects of aircraft forward motion on pure turbulent mixing noise from unheated jets have been examined experimentally in the in-flight simulation mode. Both acoustic and flow characteristics were determined by testing model-scale nozzles in an anechoic free jet facility and a wind tunnel, respectively. Scaling laws were derived from each set of experiments and found to be complementary. The implications are discussed in detail. In particular, it is shown that the measured reduction in noise at 90° to the jet axis is a pure source alteration effect.     

Noise from small air jets and a quiet valve

Noise measurements of air jets of from 0·0794 to 0·635 cm diameter, with jet exit velocity varying from 54 to 244 m/s, to frequencies of 100 kHz are presented. Results are compared to those previously obtained for larger nozzles; acoustical power spectral density curves are found to be similar to those for the larger nozzles at like velocities. Results of a noise survey conducted near a 0·127 m line size quiet vent valve having approximately 20 000 square jets, 0·127 cm on a side are presented and found to agree with the laboratory nozzle noise data. Noise above a jet velocity of 120 m/s was found to be quadrupole in nature, while below this velocity dipole surface sound was observed; this surface noise is the noise of quiet valves, which operate at low velocities. It is estimated that a quiet valve jet of 0·025 cm diameter, with a velocity near 60 m/s will exhibit a peak acoustical power spectral density at frequencies beyond the range of human audibility.     

PSP measurement of flow fields in a supersonic combustor with a backward-facing step

The mixing fields within a SCRAM-jet combustion chamber are visualized using pressuresensitive paint (PSP) as an oxygen sensor. The experiments are performed in a small supersonic wind tunnel at the National Aerospace Laboratory — Kakuda Research Center (NAL-KRC). The main stream Mach number is 2.4, and the dynamic pressure ratios between the injected gas and the main flow are 0.3, 0.7, 1.1 and 1.5. Three fuel injection nozzles are used; oxygen is injected from the central nozzle and air from the two nozzles at either side. The spread of the injected gas is measured to observe the effects of placing the nozzles in different positions. The results show that the jet has its own independent flow structure, and that little mixing of gases occurs between the flow structures created by each nozzle. When the injection dynamic pressure ratio is increased, the oxygen fraction rises in the recirculation zone and falls in the separation zone downstream of the injection.     

Shock associated noise of supersonic jets from convergent-divergent nozzles

Results of experimental and theoretical studies of the characteristics of shock associated noise from imperfectly expanded supersonic jets over an extensive range of underexpanded and overexpanded operating conditions are described. This kind of broadband noise is believed to be generated by the weak but coherent interaction between the downstream propagating large scale turbulent flow structures in the mixing layer of the jet and the nearly periodic shock cell system. Theoretical reasoning based on this mechanism leads to the scaling formula that the intensity of shock associated noise varies as (M_j² ? M_d²)² where M_j and M_d are the fully expanded jet operating Mach number and nozzle design Mach number, respectively. This formula holds for underexpanded as well as overexpanded jet Mach numbers. In addition, a peak frequency formula is also derived from the same model. The noise intensity, directivity and spectra of supersonic jets from a convergent-divergent nozzle of design Mach number 1·67 were measured in an anechoic facility over the Mach number range of 1·1 to 2·0. The effect of jet temperature was investigated by operating the jet at three temperature conditions. These sets of data provide sufficient information for fully assessing the relative importance and characteristics of shock associated noise of supersonic jets from convergent-divergent nozzles. Comparisons between theoretical results and measurements show very favorable agreement.     

Effect of chevron count and penetration on the acoustic characteristics of chevron nozzles

Experimental investigations have been carried out on chevron nozzles to assess the importance of chevron parameters such as the number of chevrons (chevron count) and chevron penetration. Acoustic measurements such as overall sound pressure level, spectra, directivity, acoustic power, and broadband shock noise have been made over a range of nozzle pressure ratio from sub-critical to underexpansion levels. Shadowgraph images of the shock-cell structure of jets from various chevron nozzles have also been captured for different nozzle pressure ratios. The results indicate that a higher chevron count with a lower level of penetration yields the maximum noise suppression for low and medium nozzle pressure ratios. Of all the geometries studied, chevron nozzle with eight lobes and 0° penetration angle gives the maximum noise reduction. Chevron nozzles are found to be free from screech unlike regular nozzles. Acoustic power index has been calculated to quantitatively evaluate the performance of the various chevron nozzles. Chevron count is the pertinent parameter for noise reduction at low nozzle pressure ratios, whereas at high nozzle pressure ratios, chevron penetration is crucial. The results illustrate that by careful selection of chevron parameters substantial noise reduction can be achieved.     

Obtaining absolute acoustic spectra in an aerodynamic wind tunnel

Cost effective methods for identifying and reducing sources of noise have become essential in the design of many modern transport vehicles. Whilst closed-section wind tunnels can readily evaluate aerodynamic performance, obtaining accurate acoustic spectra is often a major challenge because of the poor signal to noise ratios available. In this paper, methods of obtaining absolute spectra from the non-acoustically treated Markham wind tunnel at the University of Cambridge are discussed. Initial measurements with a small monopole source compare well with simulations and show that it is possible to obtain similar spectra from two nested acoustic arrays. However, a series of further experiments with simplified landing gear models show very different spectra from each array. By comparing measurements with simulations, it is shown that negative side lobes affect beamforming source maps. Measurements of an ‘empty tunnel’ cross spectral matrix allow the removal of sidelobes, providing much greater consistency between spectra. Finally, a dipole beamforming vector is used to account for the directivity of the landing gear noise, leading to good agreement between absolute spectra from the differently sized arrays. This analysis demonstrates that data from a phased array in a hard-walled, aerodynamic wind tunnel can provide meaningful acoustic spectra from low-noise models.     

Estimation and interpolation of underwater low frequency ambient noise spectrum using artificial neural networks

In this work, estimation of ambient noise spectrum influenced by wind speed and wave height carried out for the frequency range of 500 Hz to 5 kHz using Feed forward Neural Network (FNN) is presented. Ocean ambient noise measurements were made in the shallow waters of Bay of Bengal using a portable data acquisition system with a high sensitivity hydrophone at a depth of 5 m from the surface.100 sets of data covering a rage of wind speeds from 2.5 m/s to 8.5 m/s with approximately 15 sets of data falling within 1 m/s over the range of wind speed were used for training the FNN. The parameter wave height which contributes to the noise producing mechanism is also used for training along with wind speed. The results revealed that the proposed method is useful in the estimation and interpolation of underwater noise spectrum level and hence in simulation for the considered frequency range. These were confirmed by calculating the Mean Squared Error (MSE) between the experimental data and the simulation. As the measurements of the underwater ambient noise level are very difficult in remote oceanic regions, where conditions are often inhospitable, these studies seem to be relevant.     

Measurements of roughness noise

Experiments have been performed on the roughness noise produced by a two-dimensional turbulent wall jet boundary layer flowing over short fetches of sandpaper roughness. A range of rough surface sizes were studied from hydrodynamically smooth through fully rough. Velocity measurements were made to document the form of the wall jet boundary layer and the influence of the roughness upon it. Acoustic measurements showed background noise levels to be very low so that the sound produced by the rough surfaces could be clearly detected with signal to noise ratios as large as 20 dB. Even hydrodynamically smooth roughness was found to produce noise, conclusively indicating the presence of scattering as a source mechanism. Variations of the roughness noise spectra with flow speed and roughness size are found to be inconsistent with any simple parameter scaling. Boundary layer wall pressure fluctuation measurements made within the roughness fetches reveal a spectral form quite different than the roughness noise, and fluctuation levels some 50-70 dB higher. Despite these differences the wall pressure and roughness noise are found to be very simply related, at least at lower frequencies (<6 kHz). The roughness noise spectrum varies closely as the product of the wall pressure spectrum, the frequency squared, and the mean-square roughness height. This is the scaling predicted by scattering theory and implies a major simplification to the problem of roughness noise prediction for stochastic surfaces.     

Application of RANS-based method to predict acoustic noise of chevron nozzles

Passive noise control devices for jet flows, such as chevron nozzles, have been studied for a long time due to their large application in turbofan engines. The main purpose of their usage is the reduction of low-frequency noise generation and thus decreasing the noise perceived at the far field. This work is a numerical study of acoustic noise generated by jet flow operating at Mach number 0.9 and Reynolds number 1.38 × 10⁶, considering two chevron nozzle geometries that differ from each other by the penetration angle into the flow. The main aim was to demonstrate that Reynolds averaged Navier Stokes (RANS)-based methods are reliable means to obtain acoustical noise predictions for the industry with a considerably low computational cost. In order to achieve this objective, computational fluid dynamics (CFD) RANS simulations were performed with a cubic k-ɛ model and the acoustic noise spectrum for different angles of radiation was obtained via the Lighthill ray-tracing (LRT) method. The numerical results for the acoustic and flow fields were seen to be in reasonable agreement with the experimental data, suggesting that this methodology can be used as a fast and useful option to predict acoustic noise of jet flows from chevron nozzles.     

超音速喷嘴叶栅造型设计及数值分析

分析了超音速喷嘴内部的流动机理并研究了超音速喷嘴的设计方法,对某液体火箭发动机用氢涡轮超音速喷嘴叶栅进行了改型设计。设计采用尖边喉部和光滑过渡喉部两种方法,其中光滑过渡喉部喷嘴型线设计采用具有局部修改能力的三次非均匀B样条曲线。对超音速喷嘴叶栅复杂内流的全三维数值模拟结果表明:改型叶栅流动性能明显改善,效率提高,光滑过渡喉部喷嘴性能优于尖边喉部喷嘴。     

Wind dependence of ambient noise in shallow water of Bay of Bengal

This work reports on investigations into the wind dependence of ambient noise in the Bay of Bengal. Ambient noise measurements were made in the shallow water of Bay of Bengal using a portable broadband, high frequency data acquisition system together with a sensitive hydrophone suspended from the measuring platform at a depth of 5 m from the surface where the ocean depth was 25 m. Periodic measurements were carried out for one year corresponding to a wind speed range between 2 m/s and 9 m/s during summer, monsoon and winter seasons. The proportionality of the noise level with wind speed for frequencies ranging from 500 Hz to 6 kHz for each season was studied. The analysis reveals that the correlation between the wind speed and the ambient noise spectrum level was higher at lower frequencies. The results of empirical fitting based on analysis were used for noise level prediction and the model predictions compare well with the measured noise level. Further it was observed that the wind generated noise level measured during summer was approximately 8 dB less than that in other seasons. On the other hand the proportionality between the noise level and the wind speed was less during winter.     

The Acoustic Performance of 3D Printed Multiple Jet Nozzles with Different Configurations

This work investigated multiple jet nozzles with various geometrical shape, number of exits, and material on reducing noise radiated from jet flows. Nozzles are categorized in two groups with few and many exit numbers, each with various exit shapes, slot and circular, and geometry. Firstly, nozzles are designed and then fabricated by a 3D printer, Form Labs, Form2USA, with polymeric resin. Also, the nozzle with the most noise reduction made of stainless steel. Noise and air thrust were measured at three air pressure gauges, 3, 5, 7 BAR and directions from nozzle apex, 30°, 90°, 135°. Nozzles with slot exit shape made of both plastic and stainless steel revealed the most noise reduction among all nozzles with few exit numbers, nearly 11–14 dB(A) and 11.5–15 dB(A), respectively. On average, slotted nozzle noise reduction was nearly 5–6 dB(A) more than finned nozzle. However, nozzles with more exit numbers, finned and finned-central exit, illustrated much more noise reduction than nozzles with few exit numbers, by almost 16–18 dB(A), they represented similar sound. All tested nozzles and open pipe demonstrated equal air thrust at each pressure gauges. The nozzles with slotted exit shape, either plastic or stainless steel, can provide reasonable noise reduction in comparison to other configuration with few exit numbers. In contrast, nozzles with more exit numbers demonstrated the most noise reduction.     

JF12长实验时间激波风洞10°尖锥气动力实验研究

介绍了在中国科学院力学研究所JF12长实验时间激波风洞上开展的10°尖锥标模的天平测力实验研究结果.JF12激波风洞的实验时间为100~130 ms,名义Mach数为7.0,喷管出口直径为2.5 m,总焓为2.5 MJ/kg,复现了35 km高空的飞行条件.采用六分量应变天平,攻角分别为-5,0,5,10和14°,模型长度为1.5 m,质量为50 kg.实验结果表明,在100~130 ms的实验时间里,应变天平的输出信号含有3~4个完整周期,可以通过对天平的输出信号进行平均直接获得气动力/矩测量结果,而不再需要进行加速度补偿,且气动力系数重复测量的不确定度小于2%.JF12激波风洞气动力系数的测量结果与传统高超声速风洞的结果符合得较好,表明在2.5 MJ/kg的总焓下,真实气体效应对该模型气动力特性的影响不明显.      

Acoustic properties of heated twin jets

A thorough experimental study of the noise characteristics of twin jets is presented in this paper. Twin round jets are investigated at typical jet engine conditions: that is, with heated high velocity flow. By varying the nozzle to nozzle spacing, it is possible to discriminate between the effects of turbulent mixing and acoustic shielding. As a result of this investigation, it was established that the turbulent mixing effects (both interaction noise generation and mixing suppression) occur for closely spaced nozzles. While acoustic shielding occurs at all nozzle spacings, it plays the dominant role at wide nozzle spacings. The levels of this acoustic shielding afforded by an adjacent jet can be sufficient to cause a nearly complete masking of the noise of the shielded jet. A significant discovery of this investigation was the importance of the layer of cooler, slower moving ambient air that exists between the twin jet plumes. This inter-jet layer causes acoustic refraction and reflection, and as the nozzle separation increases, the layer extends to shield more of the jet noise sources.     

An experimental study of jet noise part II: Shock associated noise

The characteristics of the sound field of shock-containing under-expanded jet flows are studied by measuring the noise from a convergent nozzle operated over an extensive envelope of supercritical jet operating conditions. The measurements were conducted in an anechoic facility. They are complementary to the turbulent mixing noise experiments (described in Part I) for subsonic and fully-expanded (shock-free) supersonic jets. The overall results from shock-containing jets are compared directly with the corresponding results from shock-free jets, and the effects of nozzle pressure ratio and jet exhaust temperature on broadband shock-associated noise are assessed independently. For a supersonic jet, the regimes of jet operating conditions, observer angles, and frequencies over which the sound field is dominated by shock-associated noise are identified. Finally, the spectral results are compared in a preliminary manner with the spectra predicted by an existing theoretical model, and good agreement is obtained in most cases.     

机动车空气动力测试风洞的声学设计

测试、鉴定并研究高速机动车对环境及在车内所产生的噪声，必须有“安静”的风洞，抑制风洞内的气流噪声，将它的本底噪声降低到车辆噪声以下，测试大厅中有足够低的以上获得应有的自由声场范围，所有的声学处理措施不影响风洞的空气动力性能；吸声构件中不含矿物性纤维材料；具有相应的阻燃性能并易于清洁，本文介绍了满足以上所有要求的斯图加特大学空气动力实验室风洞的声学设计和所采用的新型吸声材料，给出了构造大样及实测结果     

激波管风洞中全尺寸涡轮试验的若干气动问题

暂冲式涡轮实验台是促进涡轮部件技术进步的关键设施．本文对激波管风洞全尺寸涡轮实验台若干气动问题进行了研究，结果表明：在暂冲式风洞中，涡轮建立稳态流场所需时间正比于涡轮叶排的轴向尺寸和折合流量．激波管风洞、喷管、实验段间匹配非常关键．     

Nature of convection-stabilized DC arcs in dual-flow nozzlegeometry. I. The cold flow field and DC arc characteristics

An experimental investigation of the steady-state low current air arcs in a dual-flow nozzle system is presented. The cold flow field with no arc was determined for various nozzle geometries, i.e. two- and three-dimensional and orifice nozzles, and nozzle pressure ratios. Supersonic flow separation and oblique and detached shock waves were observed in the flow field. Using a finite-element computer program, the Mach number contours were determined in the flow field for various nozzle-gap spacings and pressure ratios. In addition, the DC arc voltage and current measurements were made for an electrode gap spacing of ≈5.5 cm and current levels of I≈25, 50, and 100 A for the three nozzle geometries. The arc voltage and arc power increased rapidly as the flow speed increased from zero to sonic velocity at the nozzle throat. The shock waves in the converging-diverging nozzles resulted in a decrease in the overall resistance by about 15%