窄线宽1064 nm光纤激光泵浦高效率中红外3.8μm MgO:PPLN光参量振荡器

采用放大1064 nm掺镱光纤激光器作为泵浦源,实现了中红外3.8μm MgO:PPLN光参量振荡(OPO)激光输出。在泵浦源中,采用分布式反馈激光器(DFB)作为种子源来实现光纤激光窄线宽的调制,实现线宽2.5 nm到0.1 nm的压缩,最大平均输出功率可达40 W。进一步对不同泵浦线宽条件下中红外3.8μm MgO:PPLN OPO激光进行研究,最终在泵浦功率为18.1 W、线宽为0.1 nm、重频为1 MHz、脉宽为2 ns时,获得了最高平均输出功率为2.06 W的3822.5 nm激光输出,光-光转换效率为11.38%,光束质量为M2=2.34,提高了窄线宽泵浦对中红外MgO:PPLN OPO激光输出效率。     

半导体光放大器中光波传输特性研究

根据半导体光放大器(SOA)载流子速率方程和光波在SOA内的传输方程,采用分段的方法计算出光波功率和相位与载流子浓度的关系公式。在泵浦光输入功率分别为5mW和15mW情况下通过仿真得到泵浦光输出波形和归一化转换光波形,其中归一化转换光的波形变化可间接体现不同泵浦光输入功率对SOA内载流子浓度的影响。分析了泵浦光波长和SOA注入电流对探测光的归一化输出、相位和频率啁啾产生的影响。结果表明,随着泵浦光波长的增加,探测光的三种光波特性曲线逐渐趋于平缓。注入电流将会直接影响到SOA的载流子浓度,以此对探测光的输出产生影响,注入电流越大,探测光的频率漂移越远。     

光纤激光泵浦MgO:PPLN高功率中波红外光参量振荡器

为实现高效率、高功率中波红外激光输出,研制基于MgO:PPLN晶体的中波红外光参量振荡器（OPO）,泵浦源为基于主振荡功率放大（MOPA）结构的线偏振掺Yb光纤激光器（YDFL）。实验结果表明:YDFL可实现最高79.1 W的1064.1 nm脉冲线偏振激光输出;在YDFL泵浦下,通过优化输出镜曲率半径和泵浦光束腰直径,该OPO实现最高9.15 W的3.754 μm脉冲激光输出,光光转换效率为11.57%,重复频率为300 kHz,脉冲宽度约为110 ns。     

温度调谐MgO：LiNbO3晶体光参量振荡器

采用调Q Nd:YAG激光倍频光(0.532μm)泵浦温度调谐MgO:LiNbO_3晶体单、双谐振光参量振荡器(OPO包括DRO、SRO)的实验结果.双谐振(DRO)调谐范围达844.1～1411.3nm,最低泵浦阈值0.22mJ/pulse;单谐振(SRO)调谐范围达738.9～1032.2nm,最低泵浦阈值0.66mJ/pulse.最大能量转换效率为10.4%.     

高亮度人眼安全KTP OPO激光器

采用多模NdYAG激光器泵浦非临界相位匹配的KTP-OPO,获得了光束角2.3 mrad、输出能量400 mJ、平均功率12 W、光-光转换效率40%的1 572 nm激光.泵浦源的参数为能量1 J、重复频率30 Hz.分析认为采用KTP OPO将NdYAG激光器的1 μm激光转换到人眼安全波段的方法是获得1.5 μm激光的最有效的手段之一;非临界相位匹配的KTP OPO的主要优点是大的接受角和无走离,因此即使多纵模激光泵浦情况下也可以获得很高的转换效率.     

单块KTA晶体级联光参量振荡2.6 μm激光器

提出了一种新型的基于非临界相位匹配KTA晶体的自级联光参量振荡(OPO)激光技术。采用LD端面泵浦Nd:YVO4晶体实现1.06 m振荡,腔内泵浦按非临界相位匹配角度切割的KTA晶体,将KTA晶体初次OPO产生的1.5 m信号光封闭在腔内用作二次OPO的泵浦光,实现基于单块KTA晶体自级联OPO的转化。在输出功率8 W的808 nm波长半导体激光泵浦下获得输出功率超过400 mW、斜效率12.7%的2.6 m波长激光输出。结果表明基于单块KTA晶体的级联光参量振荡激光器可望成为获得脉冲2.5~2.7 m波段中红外激光的有效途径。     

200mJ光泵浦氨气太赫兹激光器北大核心CSCD

利用光栅选支调谐的TEA CO2激光器作为泵浦源设计了高能量脉冲光泵浦太赫兹激光器。太赫兹激光谐振腔由2m长的石英玻璃管、GaAs泵浦光输入窗和SiO2太赫兹光输出窗组成,氨气充入谐振腔内作为增益介质。太赫兹激光的波长由自主设计的金属线栅F-P干涉仪测量。实验中在多个波长处都获得了强烈的太赫兹光输出,其中151.5μm太赫兹光的输出脉冲能量高达204mJ,对应的泵浦光能量为32J。最后,还给出了利用151.5μm太赫兹光进行透视成像的实验结果。     

基于台阶声光调Q外腔泵浦MgO:PPLN光参量振荡器的3.4 μm中红外脉冲串激光器

本文报道了一种台阶声光调Q外腔泵浦MgO:PPLN光参量振荡器的3.4 μm中红外脉冲串激光器.建立了基频台阶声光调Q理论模型,模拟了不同台阶调Q间隔时光子数密度随时间变化趋势,获得了台阶信号最优触发时间,确定了台阶声光调Q获得脉冲串激光输出的可能性.根据理论模拟设计台阶信号触发时间,并应用于台阶声光调Q外腔泵浦MgO:PPLN光参量振荡器的中红外脉冲串激光器实验中,在每个重复周期内声光Q开关分三次开启,获得了单脉冲包络含三个子脉冲的3.4 μm中红外脉冲串激光输出.脉冲包络内子脉冲间隔为5 μs,最窄脉宽为12.8 ns,脉冲包络重频为20 kHz,理论和是实验中均发现脉冲包络内子脉冲宽度逐渐增大.在最大平均输出功率为1.08 W时, 1064 nm基频光与3.4 μm参量光的光-光转换效率为10.05%,光束质量因子M²为2.01.     

双光子共振激发钠原子六波混频过程

双光子激发钠原子所产生的级联受激辐射光子与入射激光双光子可产生光波混频。实验共观测到十一条六波混频与十条四波混频谱线。理论分析表明脉冲激光泵浦下的光波混频过程仍可用稳态近似计算混频光强。非线性极化系数X不仅与基态布居数也与激发态布居数有关。X的共振增强效应对获得强混频输出有重要作用。     

宽波段连续调谐全固态CW PPMgLN光学参量振荡器

利用半导体激光泵浦输出1064 nm波长的全固态连续Nd:YVO4激光器作为泵浦源,采用周期调谐和温度调谐组合调谐技术,对基于掺氧化镁周期性极化铌酸锂晶体（MgO:LiNbO3, PPMgLN）准相位匹配（QPM）的全固态连续波（CW）光学参量振荡器（OPO）宽波段无分立连续调谐输出特性进行研究。实验采用连续工作模式和外腔结构,基于多周期PPMgLN晶体的30.2,30.4和30.6 m周期,在改变晶体的极化周期的基础上,同时在30～100 ℃范围内调节晶体工作温度。实验结果表明:CW PPMgLN OPO的泵浦阈值仅为0.22 W;不同极化周期需要的温度调谐范围不同;信号光在1 559.8～1 597.2 nm近红外波段和闲频光在3 187.3~3 347.3 nm中红外波段连续调谐输出。实现了外腔式全固态CW OPO在信号光和闲频光波段的无分立连续调谐输出。     

High-energy PPMgLN optical parametric oscillator pumped by a 1.064 μm E-O Q-Switched Nd:YAG laser

A high-energy PPMgLN optical parametric oscillator (OPO) pumped by a E-O Q-switched Nd:YAG laser working at 1.064 μm was successfully illustrated. A maximum output pulse energy of 3.4 mJ was obtained with a pump threshold of 1.5 mJ and a slope efficiency of 30% around room temperature. The OPO output signal and idler wavelength were 1552 and 3384 nm, respectively. The damage to the input surface of PPMgLN crystal was carefully observed with a damage threshold of 4.6 J/cm².     

Zig-Zag板条泵浦的2.12μm激光器

 为了实现窄脉宽、高峰值功率2.12 μm激光的稳定输出,设计了基于侧面泵浦Zig-Zag 板条产生1.06 μm基频光,进而泵浦KTP晶体通过II类相位匹配产生2.12 μm激光的光参量振荡实验。对外腔及内腔进行了实验研究,分别获得了1.53%和2.86%的电光转换效率。在20 Hz频率下内腔2.12 μm输出能量达到70 mJ以上,脉宽7 ns~9 ns。其中内腔实验中能量输出稳定度接近8%。     

Travelling-wave 1.57-µm optical parametric oscillator driven by a pulsed multimode Nd3+:YAG laser

The generation properties of an optical parametric oscillator (OPO) with a three-mirror ring resonator have been investigated under conditions of a pulsed pump by multimode radiation from a Nd³⁺:YAG laser. KTP crystals were used as the OPO nonlinear medium. At pump energies up to 100 mJ, decreasing the diameter d of the Nd³⁺:YAG laser beam causes a decrease in OPO radiation divergence and an increase in the generation efficiency at λ = 1.571 μm despite a decrease in the differential efficiency. At d = 2.25 mm and a KTP crystal total length of 40 mm, the efficiency of the pump conversion to the signal-wave pulse reaches 36.5%. Based on the traveling-wave OPO, a compact, highly effective, eye-safe laser source radiating pulses of up to 35 mJ in energy, 11 nsec in duration, and 10 Hz in repetition rate at electrical pump energy of ≤ 8 J is developed. At the 86.5% level of the total pulse energy, the source-beam divergence does not exceed seven diffraction limits. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 4, pp. 516–523, July–August, 2008.     

Eye-safe radiation source based on an optical parametric oscillator

We have studied an optical parametric oscillator (OPO) with an unstable telescopic cavity, placed inside the cavity of an actively Q-switched multimode Nd³⁺:KGW pump laser. We used a KTP crystal as the nonlinear medium for the OPO. We have compared the emission characteristics of OPOs with unstable telescopic and planar cavities. We have established that compared with the planar cavity, the unstable cavity reduces the OPO beam divergence and improves the spatial distribution of the radiation energy in the far wave zone. Based on our investigations, we have designed a compact eye-safe (λ = 1.578 μm) laser source with natural cooling, emitting (for electrical pumping energy 7.3 J) pulses with pulse energy 22 mJ and pulse duration 6 nsec. The FWHM beam divergence for the source is no greater than 3.5 mrad. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 2, pp. 254–259, March–April, 2006.     

High-efficiency nanosecond optical parametric oscillator with the stable ring configuration

High stability nanosecond OPO operation at 1.57 μm was realized based on the type II non-critically phase-matched (NCPM) KTP crystal by utilizing a single frequency Nd:YAG master oscillator power amplifier (MOPA) laser as pump source. Energy conversion efficiency of 18.1% was demonstrated with single-pass ring cavity which was approximately two times more than that of critical ring cavity. The highest slope efficiency of 37.76% and maximum signal pulse energy of 3.1 mJ were attained with the output reflectivity of R = 50% at the pulse repetition frequency of 100 Hz. Experimental results reveal that the nanosecond OPO with ring stable configuration is a promising design to meet the need of IPDA’s transmitter.     

Optical parametric oscillators for high pulse energy and high average power operation based on large aperture periodically poled KTP and RTA

We report on optical parametric oscillators (OPOs) based on large aperture periodically poled KTiOPO₄ (PPKTP) and RbTiOAsO₄ (PPRTA) pumped with high pulse energy and high average power Q-switched solid-state lasers. The OPOs were pumped with 1064-nm pulses of a diode-pumped Nd:YVO₄ laser at 20 kHz repetition rate. The emitted signal wavelengths were 1.72 μm and 1.58 μm and the idler wavelengths were 2.79 μm and 3.26 μm, respectively. Pumping the PPKTP OPO with 7.2 W and the PPRTA OPO with 8 W average power, 2 W and 1.3 W total OPO output powers were generated. Two-dimensional measurements of the total OPO output power, the signal wavelength and the signal bandwidth in dependence on the crystal location indicated a good uniformity of the quasiphasematching structure over the entire 3-mm-thick crystals. This allowed pumping with larger pump beams and therefore with pulse energies of tens of millijoules. Pumping with different flash-lamp-pumped lasers, good OPO performance and high output pulse energies could be achieved for all pump lasers. Maximum input pulse energies of 56 mJ gave output pulse energies of as much as 18 mJ. The temperature tuning behaviors of both OPOs were measured, showing excellent agreement with calculated temperature tuning curves. New equations for temperature dispersion in RTA are presented. These results show that large-aperture PPKTP and PPRTA crystals are well suited for tunable nanosecond OPO operation with multi-watt average pump power and several tens of millijoules pump pulse energies. Received: 7 September 2001 / Published online: 7 November 2001     

Nanosecond optical parametric oscillator based on large-aperture periodically poled RbTiOAsO(4)

We report on optical parametric oscillators (OPO's) based on periodically poled RbTiOAsO(4) (PP RTA), which are pumped by Q -switched solid-state lasers. With a diode-pumped Nd:YVO(4) laser (pulse energy, 800microJ ; pulse duration, 5.5 ns; repetition rate, 1 kHz) the PP RTA OPO generated 1.58-microm signal and 3.26-microm idler radiation with a signal pulse energy of 45microJ . The large aperture of 3 mmx3 mm of the PP RTA crystal also permitted OPO operation with pump pulse energies as high as 65 mJ, provided by a flash-lamp-pumped Q -switched Nd:YAG laser (pulse duration, 20 ns; repetition rate, 10 Hz). With this pump source the OPO generated signal pulse energies as high as 17 mJ, corresponding to an efficiency of 26%. The performance of this OPO shows that large-aperture PP RTA crystals are well suited for pulsed nanosecond OPO operation with pump pulse energies of tens of millijoules.     

Mid-infrared ZGP OPO pumped by near-degenerate narrowband type-I PPKTP parametric oscillator

The total pulse energy of the signal and idler in a near-degenerate type-I periodically poled KTiOPO₄ (PPKTP) optical parametrical oscillator (OPO) was spectrally confined within a 2 nm spectral bandwidth at 2.13 μm. This was achieved by using a volume Bragg grating as the output coupler. Both the signal and the idler from the PPKTP OPO were then simultaneously used to pump a mid-infrared ZnGeP₂ (ZGP) OPO. The 2 nm bandwidth was narrower than the ZGP crystal acceptance bandwidth and, thus, made efficient conversion in the second OPO possible. A total slope efficiency of 10% from 1.06 μm to the 3.5–5 μm region was demonstrated, generating 250 μJ in the mid-IR with only 3.6 mJ of 1.06 μm pump energy. This corresponds to a Nd:YAG pump to mid-IR conversion efficiency of 7%. PACS 42.65.Yj; 42.72.Ai; 42.40.Eq     

外腔式宽调谐被动调QNd:YVO_4/PPMgLN光学参量振荡器

报道了一个低阈值宽调谐、被动调Q、单谐振掺MgO的周期性极化铌酸锂晶体(PPMgLN)光学参量振荡器。利用被动调Q的Nd:YVO4激光器作为泵浦源,采用外腔结构,在室温下,实现了PPMgLN晶体的准相位匹配光学参量振荡。光参量振荡的阈值仅为0.27W(单脉冲能量4.5μJ、脉宽35ns);在泵浦光为1.35W(脉冲能量8.2μJ、脉宽35ns),PPMgLN周期为31μm时,获得了161.9mW,3.202μm脉冲激光输出;同时获得了98.5mW的1.594μm信号光输出,总的光光转化效率达到19.3%。通过改变晶体的周期,实现了闲频光3.13～4.19μm,信号光1.43～1.65μm的宽带可调谐激光输出。     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.