Comparisons of Structural and Optical Properties of ZnO films Grown on Sapphire and Si（001）

Zinc oxide films were grown on sapphire and Si(001) substrates by reactive electron beam evaporation at low substrate temperatures,Atomic force microscopy(AFM),x-ray diffraction(XRD),and photoluminescence excitation(PLE) are employed to characterize the as-grown films.The AFM measurements have shown that all of the ZnO films present pillar-like growth properties.but the dimensional uniformity of the ZnO crystal pillars grown on sapphire was better than that on Si(001),The XRD results indicated that the prepared ZnO films both on sapphire and Si(001) were all highly c-axis oriented.the linewidths of ZnO(002)are only 0.19 and 0.28,respectively,The PLE characterizations revealed the continum absorption of the samples grown on sapphire,However,in the PLE spectra of the ZnO films grown on Si(001) substrates,a broad peak appears at the high-energy region,which indicates the formation of ZnO quantum dot structures on Si(001).     

Characterization of ZnS nanoparticles synthesized by co-precipitation method

ZnS nanoparticles are prepared by homogeneous chemical co-precipitation method using EDTA as a stabilizer and capping agent. The structural, morphological, and optical properties of as-synthesized nanoparticles are investigated using x-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, ultraviolet-visible(UV-Vis)absorption, and photoluminescence spectroscopy. The x-ray diffraction pattern exhibits a zinc-blended crystal structure at room temperature. The average particle size of the nanoparticles from the scanning electron microscopy image is about50 nm. The ultraviolet absorption spectrum shows the blue shift in the band gap due to the quantum confinement effect.The photoluminescence spectrum of Zn S nanoparticles shows a blue visible spectrum.     

ZnO Nanostructures Grown on A1N/Sapphire Substrates by MOCVD

ZnO nanorods and nanotubes are successful synthesized on A1N/sapphire substrates by metal-organic chemical vapour deposition （MOGVD）. The different morphology and structure properties of ZnO nanorods and nanotubes are found to be affected by the A1N under-layer. The photoluminescence spectra show the optical properties of the ZnO nanorods and nanotubes, in which a blueshift of UV emission is observed and is attributed to the surface effect.[第一段]     

Structural and Optical Characteristics of InGaN／GaN Multi-Quantum Wells Grown on α-and c-Plane Sapphire Substrates

We investigate the structural and optical properties of InGaN-based multi-quantum wells grown on α-c plane sapphire substrates by atomic force microscopy, high-resolution x-ray diffraction and temperature-dependent photoluminescence measurements. The multi-quantum wells grown on α-plane sapphire substrate show stronger exciton localization effect compared with that grown on the c-plane substrate, although the threading dislocation densities in the two samples are almost the same. We attribute the results to the different in-plane strain of quantum well grown on different substrate orientations at the same growth temperature. Since the excitonloca lization effect plays a key role to obtain high efficiency InGaN-based optoelectronics devices, the presented result should be emphasized.     

Rapid Thermal Annealing Effects on Structural and Optical Properties of Self-Assembled InAs／GaAs Quantum Dots Capped by InAIAs／InGaAs Layers

Effects of rapid thermal annealing on the optical and structural properties of self-assembled InAs/GaAs quantum dots capped by the InAlAs/InGaAs combination layers are studied by photoluminescence and transmission electron microscopy. The photoluminescence measurement shows that the photoluminescence peak of the sample after 850℃ rapid thermal annealing is blue shifted with 370meV and the excitation peak intensity increases by a factor of about 2.7 after the rapid thermal annealing, which indicates that the InAs quantum dots have experienced an abnormal transformation during the annealing. The transmission electron microscopy shows that the quantum dots disappear and a new InAlGaAs single quantum well structure forms after the rapid thermal annealing treatment. The transformation mechanism is discussed. These abnormal optical properties are attributed to the structural transformation of these quantum dots into a single quantum well.     

Rational doping for zinc oxide and its influences on morphology and optical properties

Zinc oxide(ZnO) nanopowders doped with different metal ions(Me, Me = Sn4+, In3+, Mn2+, and Co2+) are prepared by a simple sol–gel method. Influences of the ion doping on morphology and optical properties of the resulting ZnxMeyO are investigated by scanning electron microscopy, X-ray diffraction, UV-vis absorption spectrum, and photoluminescence. The morphology of ZnO can be tailored by ion doping, which is closely related not only to the ionic radii and electronegativities of the doped ions, but also to their oxidation states and electron configurations. The optical band gap and photoluminescence of ZnO can also be modulated by ion doping, which results from a combination of different effects, Burstein–Moss, band tail, charge compensation, sp–d exchange, non-radiative recombination, and blocking barrier. This may offer us a viable approach to tuning the(optical) properties of ZnO-based materials via rational ion doping.     

Time delay in InGaN multiple quantum well laser diodes at room temperature

This paper reports that a long delay between the beginning of pumping current pulse and the onset of optical pulse is observed in InGaN laser diodes.The delay time decreases as the pumping current increases,and the speed of the delay time reduction becomes slower as the current amplitude increases further.Such delay phenomena are remarkably less serious in laser diodes grown on GaN substrate than those on sapphire.It attributes the delay to the traps which cause a large optical loss by saturable absorption and retard the laser action.The traps can be bleached by capturing injected carriers.The effect of GaAs laser irradiation on InGaN laser action demonstrates that the traps responsible for the delay are deep centres which can be filled by the photo-assisted processes.     

Properties of GaN on different polarity buffer layers by hydride vapour phase epitaxy

This paper reports on N-, mixed-, and Ga-polarity buffer layers are grown by molecular beam epitaxy （MBE） on sapphire （0001） substrates, with the GaN thicker films grown on the buffer layer with different polarity by hydride vapour epitaxy technique （HVPE）. The surface morphology, structural and optical properties of these HVPE-GaN epilayers are characterized by wet chemical etching, scanning electron microscope, x-ray diffraction, and photoluminescence spectrum respectively. It finds that the N-polarity film is unstable against the higher growth temperature and wet chemical etching, while that of GaN polarity one is stable. The results indicate that the crystalline quality of HVPE-GaN epilayers depends on the polarity of buffer layers.     

Effects of Electron-Phonon Interaction on Linear and Nonlinear Optical Absorption in Cylindrical Quantum Wires

The electron-phonon interaction influences on lineax and nonfineax optical absorption in cylindrical quantum wires （CQW） with an infinite confining potential axe investigated. The optical absorption coefficients are obtained by using the compact-density-matrix approach and iterative method, and the numerical results are presented for GaAs CQW. The results show that the electron-phonon interaction makes a distinct influence on optical absorption in CQW. The electron-phonon interaction on the wave functions of electron dominates the values of absorption coefficients and the correction of the electron-phonon effect on the energies of the electron makes the absorption peaks blue shift and become wider. Moreover, the electron-phonon interaction influence on optical absorption with an infinite confining potential is different from that with a finite confining potential.     

Structural and optical investigation of nonpolar a-plane GaN grown by metal-organic chemical vapour deposition on r-plane sapphire by neutron irradiation

Nonpolar (1120) a-plane GaN films are grown by metal-organic chemical vapour deposition (MOCVD) on r-plane (1102) sapphire.The samples are irradiated with neutrons under a dose of 1 × 10 15 cm 2.The surface morphology,the crystal defects and the optical properties of the samples before and after irradiation are analysed using atomic force microscopy (AFM),high resolution X-ray diffraction (HRXRD) and photoluminescence (PL).The AFM result shows deteriorated sample surface after the irradiation.Careful fitting of the XRD rocking curve is carried out to obtain the Lorentzian weight fraction.Broadening due to Lorentzian type is more obvious in the as-grown sample compared with that of the irradiated sample,indicating that more point defects appear in the irradiated sample.The variations of line width and intensity of the PL band edge emission peak are consistent with the XRD results.The activation energy decreases from 82.5 meV to 29.9 meV after irradiation by neutron.     

Columnar Structures and Stress Relaxation in Thick GaN Films Grown on Sapphire by HVPE

Thick GaN films with high quality are directly grown on sapphire in a home-built vertical hydride vapour phase epitaxy （HVPE） reactor. The optical and structural properties of large scale columnar domains near the interface are studied using cathodoluminescence and micro-Raman scattering. These columnar domains show a strong emission intensity due to extremely high free carrier concentration up to 2 × 10^19 cm^-3, which are related with impurities trapped in structural defects. The compressive stress in GaN film clearly decreases with increasing distance from interface. The quasi-continuous columnar domains play an important role in the stress relaxation for the upper high quality layer.     

立方氮化硼的振动光谱及反射光谱的研究

 将黑色、黄色、棕色三种小于50 μm立方氮化硼粉末为样品，研究了其红外光谱、拉曼光谱、反射光谱，结果表明：（1）样品的红外光谱中，1 818 cm^-1和1 548 cm^-1属于cBN的晶格本征振动，而立方氮化硼的晶格本征振动外的晶体缺陷吸收则发生在~800 cm^-1，1 580 cm^-1~1 740 cm^-1和大于2 400 cm^-1处。（2）拉曼光谱测试表明，在1 052 cm^-1和1 304 cm^-1附近出现的散射与cBN不具有反演中心及cBN具有立方结构这样的事实相一致，并且这种散射伴随着布里渊区中心声子的横向和纵向发射。144 cm^-1附近出现的散射，被认为是由于局部振荡模式的出现，在反斯托克斯区造成的信号，这与晶格中杂质缺陷有关。（3）依据得到的反射光谱，计算了cBN单晶禁带宽度，发现这三种cBN都具有大于金刚石的禁带宽度值，分别为：E_g(黑)=6.21 eV，E_g(黄)=5.73 eV，E_g(棕)=5.71 eV。     

An Artificially Garnet Crystal Materials Using In Terahertz Waveguide

A hypothesis is brought forward that the materials with low propagation loss in both optical and microwave band may exhibit good performance in terahertz （THz） band because THz wave band interspaces those two wave bands. For the purpose-of exploring a kind of low-loss material for THz waveguide, Lu2.1Bi0.9Fe5O12（LuBiIG） garnet films are prepared by liquid phase epitaxy （LPE） method on a gadolinium gallium garnet （GGG） substrate from lead-free flux because of the good properties in both optical and microwave bands. In microwave band, the ferromagnetic resonance （FMR） linewidth of the film 2△H = 2.8-5.1Oe; in optical band, the optical absorption coefficient is 600cm^-1 at visible range and about 100-170cm^-1 when the wavelength is longer than 800nm. In THz range, our hypothesis is well confirmed by a THz-TDS measurement which shows that the absorbance of the film for THz wave is 0.05-0.3 cm 1 and the minimum value appears at 2.3 THz. This artificial ferromagnetic material holds a great promise for magnetic field tunable THz devices such as waveguide, modulator or switch.     

Contrast and phase characterization of a high-peak-power 20-fs laser pulse

We fully characterize a high-peak-power, ultrashort laser pulse in a Ti:sapphire chirped-pulse amplification laser system. The contrast, temporal, and spectral phases of the 20-fs pulse are determined by using high-dynamic-range cross-correlation and frequency-resolved optical gating techniques. Minimization of the total phase error can be achieved by balancing the phase terms of the group delay dispersion and quartic. The laser system is currently being applied to perform high-field atomic ionization experiments at 10²⁰ W/cm².     

Three-Step Growth Optimization of AlN Epilayers by MOCVD

A three-step growth process is developed for depositing high-quality aluminium-nitride （AlN） epilayers on （001） sapphire by low pressure metalorganic chemical vapour deposition （LP-MOCVD）. We adopt a low temperature （LT） A1N nucleation layer （NL）, and two high temperature （HT） A1N layers with different V/Ⅲ ratios. Our results reveal that the optimal NL temperature is 840-880℃, and there exists a proper growth switching from low to high V/Ⅲ ratio for further reducing threading dislocations （TDs）. The screw-type TD density of the optimized AIN film is just 7.86×10^6 cm^-2, about three orders lower than its edge-type one of 2×10^9 cm^-2 estimated by high-resolution x-ray diffraction （HRXRD） and cross-sectional transmission electron microscopy （TEM）.     

Multilayer Au/TiO2Composite Films with Ultrafast Third-Order Nonlinear Optical Properties

We report on the ultrafast third-order optical nonlinearity in multilayer Au/TiO2 composite films fabricated on quartz substrates by pulsed laser deposition technique. The linear optical properties of the films are determined and optical absorption peaks due to surface plasmon resonance of Au particles are observed at about 590hm. The third-order optical nonlinearities of the films are investigated by z-scan method using a femtosecond laser （50 fs） at the wavelength of 800 nm. The sample showed fast nonlinear optical responses with nonlinear absorption coefficient and nonlinear refractive index being -3.66 × 10^-10 m/W and -2.95 × 10^-17 m^2/W, respectively. The results also show that the nonlinear optical effects increase with the increasing Au concentration in the composite films.     

Nitrogen-Doped Chemical Vapour Deposited Diamond： a New Material for Room-Temperature Solid State Maser

Electron spin resonance （ESR） in polycrystalline diamond films grown by dc arc-jet and microwave plasma chemical vapour deposition is studied. The films with nitrogen impurity concentration up to 8 × 10^18 cm^-3 are also characterized by Raman, cathodoluminescence and optical absorption spectra. The ESR signal from P1 centre with g-factor of 2.0024 （nitrogen impurity atom occupying C site in diamond lattice） is found to exhibit an inversion with increasing the microwave power in an H102 resonator. The spin inversion effect could be of interest for further consideration of N-doped diamonds as a medium for masers operated at room temperature.     

Photopolymerization-Induced Two-Beam Coupling and Light-Induced Scattering in Polymethyl Methacrylate

Light amplification due to two-beam coupling is realized in doped polymethyl methacrylate （PMMA） glasses. A coupling gain as large as 14 cm^-1 is obtained. The dynamic behaviour of absorption and light-induced scattering due to the process of photopolymerization are also studied. The results show that the amplification and its dynamic process enable possible applications of PMMA in optical devices.     

Influence of Vacuum Organic Contaminations on Laser-Induced Damage of 1064 nm Anti-Reflective Coatings

We investigate the influence of vacuum organic contaminations on laser-induced damage threshold （LIDT） of optical coatings. Anti-reflective （AIR） coatings at 1064 nm made by Ta2 O5/SiO2 are deposited by the ion beam sputtering method. The LIDTs of AR coatings are measured in vacuum and in atmosphere, respectively. It is exhibited that contaminations in vacuum are easily to be absorbed onto optical surface because of lower pressure, and they become origins of damage, resulting in the decrease of LIDT from 24.5J/cm^2 in air to 15.TJ/cm^2 in vacuum. The LIDT of coatings in vacuum has is slightly changed compared with the value in atmosphere after the organic contaminations are wiped off. These results indicate that organic contaminations are the main reason of the LIDT decrease in vacuum. Additionally, damage morphologies have distinct changes from vacuum to atmosphere because of the differences between the residual stress and thermal decomposability of filmy materials.     

Large-area pulsed laser deposition of YBCO thin films: homogeneity and surface

YBCO thin films and buffer layers are deposited by a special PLD setup with an 8-cm line focus on cylindrical targets and substrate scanning perpendicular to it. Different kinds of substrates (SrTiO₃, MgO, LaAlO₃, Y-ZrO₂and sapphire) as large as 7᎜ cm² were coated with YBCO. Two important aspects of the presented PLD setup will be discussed in detail: the method of substrate heating and the variation of the angle between the incident laser beam and the target surface ("wobbling"). The surface of the target material has been investigated by SEM. The influence of target "wobbling" on the time stability of the plasma will be discussed. The homogeneity of the deposited YBCO films with respect to structural and electrical properties has been investigated by XRD, RBS/channeling, and spatially resolved inductive measurements of T_c and j_c. The values of j_c on 7᎜ cm²in situ buffered sapphire substrates are 2.0 MA/cm² at (77 K, 0 T) with a j_c variation of less than ᆨ%.