Synthesis and characterization of thermoluminescent Li2B4O7 nanophosphor

Lithium borate (Li₂B₄O₇) is a low Z_eff, tissue equivalent material that is commonly used for medical dosimetry using the thermoluminescence (TL) technique. Nanocrystals of lithium borate were synthesized by the combustion method for the first time in the laboratory. TL characteristics of the synthesized material were studied and compared with those of commercially available microcrystalline Li₂B₄O₇. The optimum pre-irradiation annealing condition was found to be 300 °C for 10 min and that of post-irradiation annealing was 300 °C for 30 min. The synthesized Li₂B₄O₇ nanophosphor has very poor sensitivity for low doses of gamma up to 10¹ Gy whereas from 10¹ to 4.5×10² Gy this phosphor exhibits a linear response and then from 4.5×10² to 10³ Gy it shows supralinearity. Thermoluminescence properties of Li₂B₄O₇ nanophosphor doped with Cu has also been investigated in this paper. It shows low fading and a linear response over a wide range of gamma radiation from 1×10² to 5×10³ Gy. Therefore the synthesized lithium borate nanophosphor doped with Cu may be used for high dose measurements of gamma radiations.     

A novel UV-emitting phosphor: Li6CaB3O8.5:Pb

Pure Li₆CaB₃O_8.5 and Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) materials were prepared by a solution combustion synthesis method. The phase of synthesized materials was determined using the powder XRD and FTIR. The synthesized materials were investigated using spectrofluorometer at room temperature. The emission and excitation bands of the synthesized phosphors were observed at 307 and 268 nm, respectively. The dependence of the emission intensity on the Pb²⁺ concentration for the Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) was studied and observed that the optimum concentration of Pb²⁺ in phosphor is 0.01 mol. The Stokes shift of the synthesized phosphor was calculated to be 4740 cm^-1.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Luminescent properties of Eu-activated Sr3B2SiO8: A red-emitting phosphor for white light-emitting diodes

Single-phased Sr₃B₂SiO₈:Eu³⁺ phosphor was prepared by a solid-state method at 1020 °C. The luminescence spectra showed that Sr₃B₂SiO₈:Eu³⁺ phosphor can be effectively excited by near ultraviolet light (393 nm) and blue light (464 nm). When excited at 393 or 464 nm Sr₃B₂SiO₈:Eu³⁺ exhibited the main emission peaks at 611 and 620 nm, which resulted from the supersensitive ⁵D₀→⁷F₂ transition of Eu³⁺. The luminescence intensity of Sr₃B₂SiO₈:Eu³⁺ at 611 and 620 nm reached the maximum when the doping content of Eu³⁺ was 4.5 mol%. Its chromaticity coordinates (0.646, 0.354) were very close to the NTSC standard values (0.67, 0.33). Thus, Sr₃B₂SiO₈:Eu³⁺ is considered to be an efficient red-emitting phosphor for long-UV InGaN-based light-emitting diodes.     

Luminescent properties of RE-activated CaAl2B2O7 (RE=Tb, Ce) in VUV-visible region

RE³⁺-activated α- and β-CaAl₂B₂O₇ (RE=Tb, Ce) were synthesized with the method of high-temperature solid-state reaction. Their VUV excitation and VUV-excited emission spectra are measured and discussed in the present article. The charge transfer band of Tb³⁺ and Ce³⁺ is respectively calculated to be at 151±2 and 159±3 nm. All the samples show an activator-independent excitation peak at about 175 nm and an emission peak at 350-360 nm ascribed to the host absorption and emission band, respectively.     

Surface charging at the (1 0 0) surface of Cu doped and undoped Li2B4O7

We have compared the photovoltaic charging of the (1 0 0) surface termination for Cu doped and undoped Li₂B₄O₇. While the surface charging at the (1 0 0) surface of Li₂B₄O₇ is significantly greater than observed at (1 1 0) surface, the Cu doping plays a role in reducing the surface photovoltage effects. With Cu doping of Li₂B₄O₇, the surface photovoltaic charging is much diminished at the (1 0 0) surface. The density of states observed with combined photoemission and inverse photoemission remains similar to that observed for the undoped material, except in the vicinity of the conduction band edge.     

Crystallization of 21.25Gd2O3-63.75MoO3-15B2O3 glass induced by femtosecond laser at the repetition rate of 250 kHz

We report the formation of β′-Gd₂(MoO₄)₃ (GMO) crystal on the surface of the 21.25Gd₂O₃-63.75MoO₃-15B₂O₃ glass, induced by 250 kHz, 800 nm femtosecond laser irradiation. The morphology of the modified region in the glass was clearly examined by scanning electron microscopy (SEM). By micro-Raman spectra, the laser-induced crystals were confirmed to be GMO phases and it is found that these crystals have a strong dependence on the number and power of the femtosecond laser pulses. When the irradiation laser power was 900 mW, not only the Raman peaks of GMO crystals but also some new peaks at 214 cm⁻¹, 240 cm⁻¹, 466 cm⁻¹, 664 cm⁻¹ and 994 cm⁻¹which belong to the MoO₃ crystals were observed. The possible mechanisms are proposed to explain these phenomena.     

Enhanced luminescence of Ca3B2O6:Dy phosphors by Na-codoping for LED applications

The Ca_2.95−yDy_0.05B₂O₆:yNa⁺ (0≤y≤0.20) phosphors were synthesized at 1100 °C in air by the solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE), photoluminescence (PL) spectra and thermoluminescence (TL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid-state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions on 350 nm excitation was observed at 480 nm (blue) due to the ⁴F_9/2→⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2→⁶H_13/2 transitions and 660 nm (red) due to weak ⁴F_9/2→⁶H_11/2 emissions. The PL results from the investigated Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors show that Dy³⁺ emissions increase with the increase of the Na⁺ codoping ions. The integral intensity of yellow to blue (Y/B) can be tuned by controlling Na⁺ content. By the simulation of white light, the optimal CIE value (0.328, 0.334) can be achieved when the content of Na⁺-codoping ions is y=0.2. The results imply that the Ca_2.95−yDy_0.05B₂O₆:yNa⁺ phosphors could be potentially used as white LEDs.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

Photoluminescence properties and effects of dopant concentration in Bi2ZnB2O7:Tb phosphor

A novel green phosphor, Tb³⁺ doped Bi₂ZnB₂O₇ was synthesized by conventional solid state reaction method. The phase of synthesized materials was determined using the XRD, DTA/TG and FTIR. The photoluminescence characteristics were investigated using spectrofluorometer at room temperature. Bi₂ZnB₂O₇:Tb³⁺ phosphors excited by 270 nm and 485 nm wavelengths. The emission spectra were composed of three bands, in which the dominated emission of green luminescence Bi₂ZnB₂O₇:Tb³⁺ attributed to the transition ⁵D₄ → ⁷F₅ is centered at 546 nm. The dependence of the emission intensity on the Tb³⁺ concentration for the Bi_2−xTb_xZnB₂O₇ (0.01 ≤ x ≤ 0.15) was studied and observed that the optimum concentration of Tb³⁺ in phosphor was 13 mol% for the highest emission intensity at 546 nm.     

Influence of reducing annealing on the luminescent properties of Li2B4O7:Cu single crystals

Li₂B₄O₇:Cu single-crystal annealing in the reducing environment results in a sharp drop of intensity of thermoluminescence (TSL) and X-ray luminescence (XL) peaks. It was suggested that during annealing in the reducing environment, an oxygen vacancy is produced in the LTB structure at the bridging oxygen atom site. Oxygen vacancy charge compensation takes place at the expense of reduction of the doping Cu⁺ ion to the Cu⁰ state. In this case the A⁰-type thermoluminescence center formation mechanism due to irradiation becomes impossible.     

Electrical properties vs. microstructure of nanocrystallized V2O5-P2O5 glasses — An extended temperature range study

An electronically conducting nanomaterial was synthesized by nanocrystallization of a 90V₂O₅·10P₂O₅ glass and its electrical properties were studied in an extended temperature range from − 170 to + 400 °C. The conductivity of the prepared nanomaterial reaches 2 ? 10^− 1 S cm^− 1 at 400 °C and 2 ? 10^− 3 S cm^− 1 at room temperature. It is higher than that of the original glass by a factor of 25 at room temperature and more than 100 below − 80 °C. A key role in the conductivity enhancement was ascribed to the material's microstructure, and in particular to the presence of the large number of small (ca. 20 nm) grains of crystalline V₂O₅. The observed conductivity dependencies are discussed in terms of the Mott's theory of the electronic hopping transport in disordered systems. Since V₂O₅ is known for its ability to intercalate lithium, the presented results might be helpful in the development of cathode materials for Li-ion batteries.     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

Thermoluminescence studies on Cu-doped Li2B4O7 single crystals

Lithium tetraborate (Li₂B₄O₇) is a tissue equivalent material and single crystals of this material doped with Cu are promising for dosimetric applications. In the present study highly transparent single crystals of lithium tetraborate (Li₂B₄O₇) doped with Cu (0.5 wt%) have been grown using the Czochralski technique. The Li₂B₄O₇:Cu crystals were studied using photoluminescence, X-ray diffraction (XRD), UV-vis transmission, time resolved fluorescence and thermoluminescence (TL) techniques. The TL readout of Li₂B₄O₇:Cu crystals showed two well-defined glow peaks at 402 K (peak-1) and 513 K (peak-2) for a 4 K/s heating rate. While the low temperature TL peak-1 fades completely within 24 h at room temperatures, the main dosimetric peak-2 remains the same. The TL sensitivity of the grown single crystal is found to be 3.3 times that of a conventional TL phosphor, TLD-100. The Li₂B₄O₇:Cu crystals showed a linear TL dose-response in the range from 1 mGy to 1 kGy. The TL analysis using a variable dose method revealed first order kinetics for both the peaks. Trap depth and frequency factor for peak-1 were found to be 0.81 eV and 5.2×10⁹ s⁻¹, whereas for peak-2 the values were 1.7 eV and 1.7×10¹⁶ s⁻¹, respectively.     

Enhanced photoluminescence properties of Zn2SiO4:Mn co-activated with Y/Li under VUV excitation

A series of green phosphors Zn_1.92−2xY_xLi_xSiO₄:0.08Mn²⁺ (0≤x≤0.03) were prepared by solid-state synthesis method. Phase and lattice parameters of the synthesized phosphors were characterized by powder X-ray diffractometer (XRD) and the co-doped effects of Y³⁺/Li⁺ upon emission intensity and decay time were investigated under 147 nm excitation. The results indicate that the co-doping of Y³⁺/Li⁺ has favorable influence on the photoluminescence properties of Zn₂SiO₄:Mn²⁺, and the optimal photoluminescence intensity of Zn_1.90Y_0.01Li_0.01SiO₄:0.08Mn²⁺ is 103% of that of commercial phosphor when the doping concentration of Y³⁺/Li⁺ is 0.01 mol. Additionally, the decay time of phosphor is much shortened and the decay time of Zn_1.90Y_0.01Li_0.01SiO₄:0.08Mn²⁺ is 3.39 ms, shorter by 1.83 ms than that of commercial product after Y³⁺/Li⁺ co-doping.     

Influence of ligand coordination of cobalt ions on structural properties of ZnO-ZnF2-B2O3 glass system by means of spectroscopic studies

The glasses of the composition 10ZnO-30ZnF₂-60B₂O₃ doped with different concentrations of CoO were prepared. Differential scanning calorimetric (DSC) studies, optical absorption, photoluminescence and infrared spectra of these glasses have been carried out. DSC studies have indicated that the resistance of the glass against devitrification increases with the increase in the concentration of CoO. Optical absorption spectra have exhibited one octahedral band due to ⁴T_1g(F)→²T_1g(H) and two tetrahedral bands due to ⁴A₂(⁴F)→⁴T₁(⁴P) ⁴A₂(⁴F)→⁴T₁(⁴F) transitions of Co²⁺ ions at about 525, 570 and 1400 nm, respectively. As the concentration of CoO is increased the tetrahedral bands are observed to grow at the expense of octahedral band. The luminescence spectra have exhibited two emission bands in the spectral regions of 600-700 nm and 800-900 nm due to ⁴T₁(⁴P)→⁴A₂(⁴F) and ⁴T₁(⁴P)→⁴T₂(⁴F) tetrahedral transitions of Co²⁺ ions, respectively. With the increasing content of cobalt ions in the glass matrix, the half width and intensity of these bands are observed to increase. The analysis of the results of these two spectra coupled with IR spectra has indicated that as the concentration of CoO is increased in the glass matrix, the tetrahedral occupancy of cobalt ions dominates over the octahedral occupancy and increase the rigidity of the glass network.     

Role of Ti in the luminescence process of Al2O3:Si,Ti

Al₂O₃:Si,Ti, prepared under oxidizing condition at high temperature, gives PL emission around 430 nm when excited with 240 nm. The Al₂O₃:C, TL/OSL phosphor, also shows emission around 430 nm, which corresponds to characteristic emission of F-center. Thus, to identify the exact nature of luminescent center in Al₂O₃:Si,Ti, fluorescence lifetime measurement studies were carried out along with the PL,TL and OSL studies. The PL and TL in Al₂O₃:Si,Ti show emission around 430 nm and the time-resolved fluorescence studies show lifetime of about 43 μs for the 430 nm emission, which is much smaller than the reported lifetime of ∼35 ms for the 430 nm emission (F-center emission) in Al₂O₃:C phosphor. Therefore, the emission observed in Al₂O₃:Si,Ti phosphor was assigned to Ti⁴⁺ charge transfer transition. Fluorescence studies of Al₂O₃:Si,Ti do not show any traces of F and F⁺ centers. Also, Ti⁴⁺ does not show any change in the charge state after gamma-irradiation. On the basis of the above studies, a mechanism for TSL/OSL process in Al₂O₃:Si,Ti is proposed.     

Blue light emission from Eu ions in sol-gel-derived Al2O3-SiO2 glasses

Blue light-emitting glasses were successfully prepared by doping Eu²⁺ ions in the system Al₂O₃-SiO₂. The Al₂O₃-SiO₂ glasses doped with Eu³⁺ ions were synthesized using a sol-gel method, followed by heating in hydrogen gas atmosphere to reduce into the Eu²⁺ ions. The obtained glasses exhibited emission spectra with peak at ∼450 nm due to 4f⁶5d→4f⁷ (⁸S_7/2) transition, the intensities of which strongly changed depending on their glass composition and heating conditions. The emission quantum efficiency of 48% was achieved by heating the glass with the ratio of Al³⁺ to Eu³⁺ at about 6 at 1000 °C in hydrogen gas atmosphere. It was found that the Al₂O₃-SiO₂ glasses were appropriate not only for homogeneously doping the Eu³⁺ ions in glass structure but also reducing to Eu²⁺ ions, resulting in enhanced blue light-emission properties.     

Chemical synthesis of spinel nickel ferrite (NiFe2O4) nano-sheets

The present investigation is related to the deposition of single-phase nano-sheets spinel nickel ferrite (NiFe₂O₄) thin films onto glass substrates using a chemical method. Nano-sheets nickel ferrite films were deposited from an alkaline bath containing Ni²⁺ and Fe²⁺ ions. The films were characterized for their structural, surface morphological and electrical properties by means of X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and two-point probe electrical resistivity techniques. The X-ray diffraction pattern showed that NiFe₂O₄ nano-sheets are oriented along (3 1 1) plane. The FT-IR spectra of NiFe₂O₄ films showed strong absorption peaks around 600 and 400 cm⁻¹ which are typical for cubic spinel crystal structure. Microstructural study of NiFe₂O₄ film revealed nano-sheet like morphology with average sheet thickness of 30 nm. The room temperature electrical resistivity of the NiFe₂O₄ nano-sheets was 10⁷ Ω cm.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.