光纤应变、温度、振动同时测量新技术的研究

本文介绍了集成式Bragg光纤光栅(FBG)和非本征型Fabry-Perot干涉腔(EFPI)复合传感器的结构及应用该传感器同时测量静态应变、温度和振动的原理.利用FBG、EFPI和低相干性干涉信号解调方法实现了用一个传感器同时测量三个参量.实验结果表明温度精度达±1℃,应变精度为±20με,振幅分辨率达1nm,测量重复性好.     

光纤应变、温度、振动同时测量新技术的研究

本文介绍了集成式 Bragg光纤光栅 ( FBG)和非本征型 Fabry-Perot干涉腔 ( EFPI)复合传感器的结构及应用该传感器同时测量静态应变、温度和振动的原理 .利用 FBG、EFPI和低相干性干涉信号解调方法实现了用一个传感器同时测量三个参量 .实验结果表明温度精度达± 1℃ ,应变精度为± 2 0 με,振幅分辨率达 1 nm,测量重复性好     

利用双周期光纤光栅实现应变和温度同时测量

提出了一种新颖双周期光纤光栅传感器。在同一段氢载光纤上先后写入长周期光纤光栅、短周期布拉格光纤光栅 ,利用长周期光栅和布拉格光栅对应变和温度敏感性的差异 ,可实现应变和温度的同时测量。实验中采用这种灵敏结构的双周期光栅 ,在 0～ 170 0 με和 2 0℃～ 12 0℃范围内 ,测量精度可达到± 16 με和± 0 8℃。     

基于阵列波导光栅的智能服装人体测温解调系统研究

研究并实现了一种应用于智能服装中人体温度测量的阵列波导光栅解调系统。分析了系统的解调原理,搭建了光纤布拉格光栅解调实验平台,采用了强度法解调出光纤光栅的布拉格波长,完成了光纤光栅传感器串联前后解调的实验。结果表明,系统对光纤布拉格光栅的布拉格波长的解调具有高线性度,波长测量精度可达0.001nm,光纤布拉格光栅传感器间串扰所造成的解调误差为0.000 5nm,人体温度的测量误差为±0.16℃。该解调系统精度高、串扰低,可适用于智能服装中人体温度的测量。     

同时测量温度和曲率的光纤传感器

提出了一种基于光纤布拉格光栅和马赫-曾德干涉仪相结合的同时测量曲率和温度的光纤传感器.该光纤传感器在马赫-曾德干涉仪中熔接一段布拉格光纤光栅,其中马赫-曾德干涉仪由两个花生形结构单模光纤熔接而成.实验结果表明,马赫-曾德干涉仪的透射谱中干涉峰和光纤布拉格光栅透射谱中谐振峰对曲率和温度有不同的响应灵敏度,因此可以利用矩阵实现对曲率和温度的同时测量.实验中测得马赫-曾德干涉仪曲率灵敏度为-27.58nm/m-1,光纤布拉格光栅在一定的测量范围内对曲率的变化不敏感,马赫-曾德干涉仪和光纤布拉格光栅的温度灵敏度分别为0.038 69nm/℃和0.012 17nm/℃.该系统采用全光纤结构,光纤布拉格光栅嵌入到马赫-曾德干涉仪中,因而结构紧凑和简单,且易于实现.     

阵列波导光栅解调的准分布式光纤光栅传感器

从理论上和实验上研究了一种操作简单、响应速度快,价格低廉和高分辨率的基于阵列波导光栅(AWG)的准分布式光纤布拉格光栅(FBG)传感器.该传感系统采用了阵列波导光栅双通道强度解调技术对光纤光栅的布拉格波长和温度进行精确的解调.实验结果表明,该系统对宽带宽光纤光栅的布拉格波长和温度解调均具有高线性度,考虑系统稳定性及光纤布拉格光栅之间的串扰影响,波长测量精度仍可达2 pm,温度测量精度优于0.2℃.     

基于空芯光纤和光纤布拉格光栅的温度应变同时测量传感器

提出一种新颖的温度和应变双参数同时测量的光纤传感器。该传感器由空芯光纤和光纤布拉格光栅级联而成。空芯光纤通过反谐振机理将光限制在空气纤芯内传输,满足谐振条件的光泄露出空气芯,在传输光谱上表现为周期性损耗峰。由于空芯光纤和光纤布拉格光栅的物理机理不同,对外界温度、应变的响应存在差异,利用耦合矩阵则可以精确地实现温度和应变双参数的同时测量。实验结果表明,在1550nm波长附近,空芯光纤和光纤布拉格光栅对应的温度灵敏度分别为24.55 pm/℃和12.76 pm/℃,应变灵敏度分别为-0.70pm/με和1.02pm/με,该级联结构的传感器制作简单且具有较高的测量精度。     

光纤布拉格光栅与空芯光纤多模干涉混合型温度应变双参量传感器

针对光纤应变传感器由于温度敏感而引入的测量问题,提出了一种基于光纤布拉格光栅和空芯光纤多模干涉效应的混合型温度-应变双参量传感器。该传感器由两根单模光纤与一段内径小于单模光纤纤芯直径的空芯光纤熔接制成,其中一根单模光纤的光纤端面附近预刻一组光纤布拉格光栅。空芯光纤长度为厘米量级,光波以多模形式在空芯光纤侧壁中传播。结合光纤布拉格光栅和空芯光纤多模干涉效应对温度和应变的不同响应灵敏度,通过求解双参数耦合矩阵同时获取温度和应变两个参量,并有效解决了单个传感器在温度或应变测量时的温度-应变交叉敏感性问题。采用中心波长为1 550.172 nm的光纤布拉格光栅与一段长为2.5 cm、内径为5μm的空芯光纤制备了相应的传感器,并进行了温度和应变测试。结果表明,光纤布拉格光栅和空芯光纤的温度灵敏度分别达到10.530 6 pm/℃和1.802 1 pm/℃,应变灵敏度分别达到0.720 7 pm/με和1.243 2 pm/με。     

基于宽谱光源的光纤传感波长解调系统的研究

研究制作了基于宽谱光源的光纤传感波长解调系统, 以多光纤光栅作为波长参考基准、采用可调谐光纤法布里-珀罗(F-P)滤波器作为波长扫描器件。系统中采用三次多项式拟合的方法对滤波器锯齿波的扫描电压与透射波长关系曲线进行非线性拟合, 解决可调谐光纤F-P滤波器的电压—波长非线性关系对系统测量带来的较大误差问题, 实现波长的高精度解调。采用五光纤光栅做波长参考, 单根光纤光栅传感器的解调实验结果表明：待测光纤光栅布拉格波长短期测量分辨率为3.5 pm, 长期测量稳定性为7 pm。采用该系统对光纤非本征法布里-珀罗干涉型(EFPI)应变传感器的测试结果表明, 测量应变灵敏度为2.41 nm/με, 并且应变和波长之间存在良好的线性关系, 线性相关度达到0.99991。     

基于光纤布拉格光栅传感器的光纤光栅智能夹层试验研究

传感元件与复合材料的一体化是智能结构研究的最终目标之一。设计一种具有自诊断功能的标准化、模块化光纤智能夹层系统,正是实现这种一体化最有潜力的技术途径。采用聚酰亚胺薄膜制作了基于光纤布拉格光栅（FBG）传感器的光纤光栅智能夹层,对智能夹层中光纤布拉格光栅传感器的应变、温度特性进行了标定试验,并建立了基于光纤布拉格光栅传感器光纤光栅智能夹层的应变、温度测量模型。试验表明,智能夹层内布拉格光栅波长偏移与应变、温度之间具有良好的线性关系。不过在温度测量时,必须考虑被埋人结构的热膨胀效应。利用光纤光栅智能夹层内光纤布拉格光栅传感器网络和先进信息处理技术,可以建立结构损伤主动、在线和实时监测系统。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.