非晶纳米发光材料(Y,Eu)2O3-SiO2发射光谱的分析研究

EXAFS测定表明sol-gel方法制备的纳米非晶(Y,Eu)₂O₃-SiO₂发光材料中,发光中心Eu³⁺的局域环境和晶态X₂型Y₂SiO₅Eu中Eu³⁺离子的局域环境相似。以此结构为依据,用M. F. Reid的方案计算了晶场迭加模型中的能级参数及光谱强度参数,并得到了与实验结果基本一致的理论光谱图.     

Gd2(WO4)3: Eu纳米发光材料中黄昆因子和能量传递速率的实验获得

采用共沉淀法制备了不同Eu³⁺掺杂浓度的Gd₂(WO₄)₃纳米发光材料. 测量了纳米材料样品的X射线衍射谱(XRD) 和场发射扫描电镜, 对样品的结构和形貌进行了表征. 测量了各样品的发射光谱和激发光谱(声子边带光谱), 绘制了浓度猝灭曲线, 确定了最佳的掺杂浓度为20 mol%. 通过声子边带光谱计算了不同掺杂浓度样品的黄昆因子. 测量了不同浓度样品的荧光寿命, 利用Auzel模型对Eu^{3+ 5}D₀能级荧光寿命数据进行了拟合, 确定了⁵D₀能级的固有寿命和猝灭过程中生成的声子数. 本文还根据荧光寿命数据计算了Eu³⁺之间的能量传递速率, 确定了能量传递速率与浓度的关系. 关键词： 钨酸盐 3+')" href="#">Eu³⁺ 黄昆因子 能量传递速率     

Mg5SnB2O10:Eu3+,Bi3+—一种用于发光二极管的红色荧光粉的制备及其发光性能的研究

采用高温固相法成功合成了单一相的Eu³⁺,Bi³⁺共掺的Mg₅SnB₂O₁₀红色荧光粉,并通过X射线衍射、漫反射光谱、光致发光光谱等手段对该体系的结构及其发光特性进行了测试和研究.激发光谱表明,该荧光粉在393 nm呈现Eu³⁺的⁷Fo—⁵L₆特征激发,可以与用于发光二极管的近紫外芯片很好地匹配.在393 nm激发下,其发射光谱在591,612,701 nm处呈现Eu³⁺的⁵Do—⁷F₁,⁵Do—⁷F₂,⁵D₀—⁷F₄的特征发射.并且当固定Eu³⁺的浓度时,随着Bi³⁺含量的增加,发现Bi³⁺,Eu³⁺在这一体系中存在能量传递现象,系列样品发光强度大幅度提高.通过研究系列样品在不同Bi³⁺,Eu³⁺掺杂浓度下的发光性能,得出最佳样品为Mg_4.89Eu_0.1Bi_0.01SnB₂O₁₀,其积分强度达到了商用Y₂O₂S:Eu³⁺的1.1倍.     

NaLa(MoO4)2∶Eu3+的水热调控合成与发光特性研究

采用水热法合成了不同粒径的NaLa(MoO₄)₂∶Eu³⁺微晶.通过调节乙二醇浓度和反应时间,研究了NaLa(MoO₄)₂∶Eu³⁺微晶的形貌演变过程,在水热条件下180 ℃反应16 h获得了均一梭子形NaLa(MoO₄)₂∶Eu³⁺微晶,其晶粒长度约为2.0 μm.荧光光谱分析表明,Eu³⁺取代了NaLa(MoO₄)₂中La³⁺的格位, Eu³⁺在613 nm处红光发射(⁵D₀–⁷F₂跃迁)的浓度猝灭机理是电偶极-电四极相互作用,并发生了Eu³⁺( ⁵D₁ ) + Eu³⁺(⁷F₀ )→ Eu³⁺( ⁵D₀ ) + Eu³⁺(⁷F₃) 交叉弛豫,由此导致浓度猝灭. 关键词： 钼酸盐 水热法 稀土离子 发光     

Eu3+掺杂CaMoO4微米荧光粉发光性质的研究

运用化学沉淀的方法合成了不同Eu³⁺掺杂浓度CaMoO₄微米荧光粉样品, 详细研究了样品的光致发光性质. 研究表明: CaMoO₄: Eu可以被蓝光或近紫外光有效激发, 实现高色纯度的红光发射; 样品的黄昆因子数值数量级为10^-2, 是一种弱电声耦合材料; 样品中Eu³⁺的跃迁强度参数(Ω₂)随着掺杂浓度的提高而增大, 但量子效率却随着掺杂浓度的提高而减小; 通过对样品发光的浓度猝灭曲线的分析, 确定Eu³⁺的理想掺杂浓度为25%, 并判断出Eu³⁺在CaMoO₄基质中通过交换相互作用实现能量传递. 沉淀法制备的CaMoO₄: Eu微米荧光粉具有发光色纯度好, 制备工艺简单, 耗时较少的优点, 是一种性能优异的红色荧光粉材料.     

共沉淀法制备Y2O2S：Eu3+,Mg2+,Ti4+红色长余辉材料

用共沉淀法制备了Y₂O₂S:Eu³⁺,Mg²⁺,Ti⁴⁺红色长余辉材料。测量了材料的电子显微形貌、晶体结构和发射光谱。通过与固相法制备的Y₂O₂S:Eu³⁺,Mg²⁺,Ti⁴⁺长余辉材料比较,发现两种方法都可以制备粒度基本相同的纯相Y₂O₂S基质晶体,但共沉淀法样品的颗粒结构更松散。研究了Eu³⁺浓度对两种方法制备样品的谱线发射强度的影响,通过比较共沉淀法和高温固相法制备的样品中Eu³⁺的⁵D₁→⁷F₃较高能级跃迁的587.6nm谱线强度随Eu³⁺浓度的变化,发现共沉淀法更有利于Eu³⁺均匀进入Y₂O₂S基质晶格而形成有效的发光中心。     

Y2O3: Eu,Dy的制备与红色长余辉发光性能研究

采用高温固相法合成发光样品Y₂O₃：Eu³⁺_0.01和Y₂O₃：Eu³⁺_0.01,Dy³⁺_0.01.X射线衍射分析(XRD)表明样品保持Y₂O₃晶格结构,掺入的Eu³⁺和Dy³⁺对Y_{2关键词： 长余辉 2}O₃')" href="#">Y₂O₃ 稀土掺杂 陷阱     

Y6TeO12:Eu3+红色荧光粉的制备与发光特性研究

利用高温固相法在1 200℃制备了一系列红色荧光粉(Y_1-x)₆TeO₁₂:x Eu³⁺(x=0.1～0.5)材料。对样品进行了X射线衍射、形貌特征、激发和发射光谱、浓度猝灭、热稳定性、荧光衰减曲线以及发光二极管封装与光色电性能等方面的分析与探究。结果表明：该红色荧光粉样品能被近紫外光(393 nm处)和蓝光(464 nm处)有效激发，在632 nm处表现出较强的红光发射。根据荧光强度与掺杂浓度的变化趋势，确定出最佳Eu³⁺掺杂量为x=0.3，更多的掺杂量引起浓度猝灭。进一步分析激活剂Eu³⁺间能量传递类型，得出电偶极-电偶极作用导致了浓度猝灭。(Y_0.7)₆TeO₁₂:0.3Eu³⁺在150℃时积分发光强度是室温的76.5%，热激活能为0.196 9 eV。该样品的荧光寿命为813μs，色坐标值为(0.637 6,0.343 1)，并基于板上芯片工艺进行了发光二极管封...     

Eu2+掺杂浓度对Ca2MgSi2O7∶Eu2+荧光粉发光特性的影响

采用化学共沉淀法制备了Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉.用X射线衍射仪、荧光分光光度计及光色综合测试系统对Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉的相结构、发光性能进行了测试.结果表明:其激发光谱分布在300–480 nm波长范围,谱峰位于389,430 nm处,可以被InGaN管芯产生的360–480 nm辐射有效激发;在波长为430 nm蓝光激发下,其发射光谱谱峰位于531 nm处.Ca_2-xMgSi₂O₇:xEu²⁺绿色荧光粉的发光强度随Eu²⁺掺杂量的增加而增强,当Eu²⁺掺杂量x为0.04时,发光强度达到最大值,而后开始降低,发生浓度猝灭.根据Dexter能量共振理论,浓度猝灭是由电偶极-电偶极相互作用引起的. 关键词： 2MgSi₂O₇∶Eu²⁺')" href="#">Ca₂MgSi₂O₇∶Eu²⁺ 绿色荧光粉 发光特性 白光发光二极管     

不同壳层厚度的LaF3：Eu3+/LaF3核壳结构纳米颗粒制备及发光性质

表面缺陷会使纳米材料的发光中心产生严重的猝灭，而适当厚度的同质包覆层会减少其猝灭。本文利用共沉淀法合成了LaF₃：Eu³⁺纳米颗粒和LaF₃：Eu³⁺/LaF₃核壳结构纳米颗粒，研究了颗粒的晶体结构、形貌以及不同壳层厚度对发光性能的影响。研究发现：LaF₃：Eu³⁺核心和LaF₃：Eu³⁺/LaF₃核壳结构均为六方结构。包覆同质壳层可以提高稀土离子的发光性能，包覆厚度的不同导致LaF₃：Eu³⁺/LaF₃核壳结构的荧光强度与衰减时间均发生改变。其原因是未掺杂的LaF₃壳层可以将发光中心Eu³⁺离子与LaF₃：Eu³⁺核心的表面隔离，进而减少表面对发光中心的猝灭，提高材料的发光性能。这种修饰作用与壳层厚度相关。     

Synthesis and properties of colloidal ternary ZnGa2O4:Eu nanocrystals

A nonhydrolytic hot solution synthesis technique was used to grow monodisperse ternary oxide nanocrystals of ZnGa₂O₄:Eu³⁺. The shape of ZnGa₂O₄:Eu³⁺ nanocrystals was a function of the type of precursor, and their size was controlled by changing the concentration ratio of Zn precursor to surfactant. The crystal structure of synthesized ZnGa₂O₄ nanocrystals was a cubic spinel with no detectable secondary phases. Photoluminescence of red-emitting ZnGa₂O₄:Eu³⁺ nanocrystals resulted in a high (⁵D₀-⁷F₂)/(⁵D₀-⁷F₁) intensity ratio, suggesting that the Eu³⁺ ions occupy tetrahedral Zn²⁺ sites or distorted octahedral Ga³⁺ sites with no inversion symmetry in ZnGa₂O₄ nanocrystals.     

Synthesis and luminescent properties of oleic acid (OA)-modified CaF2: Eu nanocrystals

The OA-modified CaF₂: Eu nanocrystals that can be well dispersed in chloroform to form a clear solution were synthesized and characterized. The nanocrystals have a roughly spherical shape with particle diameter of about 10 nm. Possible mechanism was proposed to explain the growth process. Upon the excitation at 395 nm, the room-temperature emission spectrum of the nanocrystals in chloroform presents the characteristic transitions ⁵D₀→⁷F_J of Eu³⁺ ions, with ⁵D₀→⁷F₂ (610 nm) transition as the most prominent group. The luminescence decay of Eu³⁺ ions in CaF₂ nanocrystals was also investigated and two luminescence lifetimes of 737 μs (11.2%) and 2.08 ms (88.8%) were obtained.     

Investigation of crystallographic sites of Eu in La2BaZnO5 by site-selective laser-excitation spectroscopy

La₂BaZnO₅:Eu³⁺ (0.05 mol%) was prepared by a solid-state reaction at high temperature. X-ray powder diffraction analysis confirmed the formation of single phase La₂BaZnO₅. Luminescence properties of La₂BaZnO₅:Eu³⁺ are investigated by site-selective laser-excitation and emission spectroscopy at 18 K. Two different crystallographic sites for Eu³⁺ corresponding to the La³⁺ and Ba²⁺ sites are identified from the ⁷F₀→⁵D₀ excitation spectra obtained by monitoring the ⁵D₀→⁷F_J (J=1, 2, …, 6) emissions. It is found that Eu³⁺ substituted for the Ba²⁺ ion experiences stronger crystal-field strength than Eu³⁺ substituted for the La³⁺ ion. Energy transfer between the two crystallographic Eu³⁺ centers is investigated by luminescence decay curves at 18 K.     

Effects of electron beam current density and temperature on peak height ratios Dj/D0 for cathodoluminescence of Ln2O2S:Eu

The change in the initial and steady state (∼0 and 5 s after initiation of electron beam irradiation) peak heights from the ⁵D₂⇒⁷F₃, ⁵D₁⇒⁷F₃ and ⁵D₀⇒⁷F₂ cathodoluminescent transitions from Eu³⁺ have been studied for Ln₂O₂S:Eu³⁺ (Ln=La, Gd) phosphors. Specifically, the intensity ratio of these transitions, designated as ⁵D₁/⁵D₀, increased and then decreased for both La₂O₂S:Eu³⁺ (0.1 mole%) and Gd₂O₂S:Eu³⁺ (0.4 mole%), as the current density was changed from 10 towards a 1000 μA/cm². These effects were shown to be consistent with feeding from the higher ⁵D₂ excited state to the lower energy ⁵D₁ excited state, resulting in an increase of the ⁵D₁/⁵D₀ ratio at low current densities. At higher current densities, energy was funneled from the ⁵D₁-⁵D₀ states, resulting in a decrease of the ⁵D₁/⁵D₀ ratio. These effects of feeding versus funneling were dependent on both the Eu³⁺ concentration and current density, and changed with time (i.e., approached a steady state after ∼5 s) due to increased activator interactions from induced internal electric fields. The magnitude of thermal quenching versus interaction quenching was investigated using changes of the peak height ratios of ⁵D₂/⁵D₀ and ⁵D₁/⁵D₀.     

Investigation of 515 nm green-light emission for full color emission LaAlO3 phosphor with varied valence Eu

Photoluminescence and lifetime decay properties of varied valence Eu were employed to investigate the luminescence mechanism of green-light emission positioned at ∼515 nm for full color emission LaAlO₃ phosphor co-doped with Eu²⁺ and Eu³⁺. The enhanced ⁵D₂→⁷F₃ transition emission of Eu³⁺ was assigned for this green emission. Energy transfer between Eu²⁺ and ⁵D₂ level of Eu³⁺ was proposed, which results in the enhancement of ⁵D₂→⁷F₃ transition emission. In addition, energy transfer relations between host-Eu and charge transfer state (CTS)-Eu were also discussed associated with the PLE spectra and band schemes.     

Effect of concentration on the luminescence of Eu ions in nanocrystalline La2O3

Nanocrystalline powders with various Eu³⁺ concentration (from 1 to 10 mol %) doped La₂O₃ were prepared via a combustion route. Their structure and morphology were characterized using X-ray diffraction (XRD) and High-resolution transmission electron microscopy. The emission spectra of the as-synthesized samples show that the strongest emission position is centered at 626 nm corresponding to ⁵D₀→⁷F₂ transition of Eu³⁺ ions and the intensity change of 626 nm emission is considered as a function of ultraviolet (240 nm) irradiation time. The excitation spectra at 626 nm monitoring indicate that the charge transfer state band is varies with different Eu³⁺ ion concentration. These results are attributed to the surface defects of the nanocrystals.     

Preparation and photoluminescence characteristics of Eu-doped MgAl1.8Y0.2O4 nanocrystals

A simple combustion route was employed for the preparation of Eu³⁺-doped MgAl_1.8Y_0.2−xO₄ nanocrystals using metal nitrates as precursors and urea as a fuel in a preheated furnace at 500 °C. The powders thus obtained were then fired at 1000 °C for 3 h to get better luminescent properties. The incorporation of Eu³⁺ activator in these nanocrystals was checked by luminescence characteristics. These nanocrystals displayed bright red color on excitation under 254 nm UV source. The main emission peak was assigned to the transition [⁵D₀→⁷F₂] at 615 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies were carried out to understand surface morphological features and the particle size. Crystal structures of the nanocrystals were investigated by the X-ray diffraction (XRD) technique. The crystallite size of the as-prepared nanocrystals was around 29 nm, which was evaluated from the broad XRD peaks. The crystallite size increased to ∼45 nm on further heat treatment at 1000 °C.     

Eu photoluminescence enhancement due to thermal energy transfer in Eu2O3-doped SiO2-B2O3-PbO2 glasses system

In this work, Eu³⁺-doped lead borosilicate glasses (SiO₂-B₂O₃-PbO₂) synthesized by fusion method had their optical properties investigated as a function of temperature. Atomic Force Microscopy images obtained for a glass matrix annealed at 350 and 500 °C show a precipitated crystalline phase with sizes 11 and 21 nm, respectively. Besides, as the temperature increases from 350 to 300 K a strong Eu³⁺ photoluminescence (PL) enhancement takes place. This anomalous feature is attributed to the thermally activated carrier transfer process from nanocrystals and charged intrinsic defects states to Eu³⁺ energy levels. In addition, the PL peaks in this temperature range were assigned to the Eu³⁺ transitions ⁵D₀→⁷F₂, at 612 nm, ⁵D₀→⁷F₁, at 595 nm, and ⁵D₀→⁷F₀, at 585 nm. It was also observed that the ⁵D₀→⁷F₃ and ⁵D₀→⁷F₄ PL bands at 655 and 700 nm, respectively, show a continuous decrease in intensity as the temperature increases.     

二氧化锆纳米材料中Eu3+的发光特性

研究了掺1mol%Eu³⁺的二氧化锆纳米材料随退火温度变化的发光性质，得到退火温度为600和800℃的样品中Eu³⁺的⁵D₀→⁷F₂发射在604nm处，这种现象不多见. 几种经不同退火温度处理的纳米材料样品在紫外光的照射下，稀土离子Eu³⁺的⁵D₀→⁷F₂发射的发光逐 关键词： 二氧化锆 纳米材料 3+')" href="#">Eu³⁺ 发光     

Improved color purity in nano-size Eu-doped YBO3 red phosphor

Nano-size YBO₃:Eu³⁺ phosphor has been synthesized by the co-precipitation method. X-ray diffraction (XRD) pattern confirmed the formation of hexagonal vaterite-type structures of YBO₃:Eu³⁺ nanoparticles. The transmission electron microscopy (TEM) study revealed the formation of spherical YBO₃:Eu³⁺ nanoparticles with size 20-40 nm. The photoluminescence spectra revealed that the ratio of the red emission (⁵D₀-⁷F₂) to the orange emission (⁵D₀-⁷F₁) was much higher in the synthesized nano-size YBO₃:Eu³⁺ phosphor. The improved relative intensity, i.e., higher R/O value of emission peaks, is due to a lower symmetry of crystal field around Eu³⁺ ions.