PS/Ag核壳结构复合微球的制备与性能

以乳液聚合法制备的平均粒径1.2~1.5μm单分散聚苯乙烯(PS)微球为核,经过超声敏化、化学镀、还原等过程制备了PS/Ag核壳结构复合微球。采用透射电镜、X射线衍射、红外光谱、紫外可见光谱对其形貌、物相、结构与光学性质进行了表征与分析。结果表明:PS/Ag复合微球粒径相对均一;通过多次敏化、控制二次银氨溶液浓度(0.002~0.006 mol/L),可实现对纳米银壳层厚度的调控;纳米银壳层沉积生长过程中,随着PS微球表面银粒子的增多、增大,复合微球的光学等离子体共振吸收峰产生显著的展宽与红移。     

Zno纳米粒子在PS中空微反应器中的合成与光学性能

通过种子乳液聚合合成核壳结构的聚甲基丙烯酸甲酯/聚苯乙烯(PMMA/PS)复合微球,通过酸碱溶胀法进一步制备出次微米级的PS中空微球. 将此中空微球作为微反应器,使在ZnO纳米粒子前驱体溶液中溶胀, 最终ZnO纳米粒子在PS中空微球中原位生成. 实验表明, 组成ZnO纳米粒子前驱体溶液的两种组 分(CH₃COO)₂Zn和LiOH的滴加顺序不同对最终生成的ZnO纳米粒子的尺寸和负载效率有很大的影响,但并不改变ZnO纳米粒子的晶型. 复合物的光致发光和UV-Vis吸     

ZnS:Mn2+/聚苯乙烯核壳及ZnS:Mn2+中空球的制备和光谱性质

采用超声化学沉积法制备了ZnS:Mn2+/聚苯乙烯核壳结构和ZnS:Mn2+空心球.产物分别用透射电镜、X射线衍射仪和光致发光谱进行了表征.透射电镜结果表明,在聚苯乙烯胶体微球表面覆盖了平均尺寸为9nm的ZnS:Mn2+纳米颗粒,X射线衍射结果进一步验证了这个结论.将核壳粒子在500℃灼烧除去PS核后,可以得到空心的ZnS:Mn2+微球,Mn2+的发射谱的峰位在540nm,与体相材料相比,蓝移了45nm,这可能是由于壳层结构引起Mn-O八面体畸变,进而导致能带结构变化引起的.     

不同Ag壳厚度Au@Ag纳米粒子的调控制备表征及表面增强拉曼光谱的效应

采用化学还原法制备了以Au为核、包覆Ag的双金属核壳Au@Ag纳米粒子,并成功地用于表面增强拉曼光谱(SERS)分析测试。通过改变制备液中Ag/Au的量比来调控Ag壳包覆厚度。采用透射电子显微镜(TEM)和紫外-可见光谱仪(UV-Vis)对Au@Ag纳米粒子的构貌进行表征。TEM显示明显存在核壳结构,且Ag壳层随Ag/Au的量比的增加而逐渐变厚;UV-Vis表明随着Ag/Au的量比的增加,Au@Ag纳米粒子出现了Au核与Ag壳吸收峰的2个等离子体共振峰,同时伴随着Au峰的蓝移和Ag峰的红移。以双甲脒为分析物,考察了不同Ag/Au的量比时的Au@Ag纳米粒子的SERS活性。结果表明,SERS活性随Ag/Au的量比的增加先增大后减小,在6∶5时其SERS增强效应最佳,此时Ag壳厚度约为6 nm。以对巯基苯胺(4-ATP)、结晶紫(CV)和双甲脒为分析测试对象,对比了Au@Ag、Ag、Au 3种基底的SERS活性。结果表明,所制备的Au@Ag纳米粒子的SERS活性要明显优于单纯的Au、Ag纳米粒子。     

通过重氮盐分子表面修饰金纳米帽子探究其对等离子体共振吸收的影响

以玻璃基底作为聚苯乙烯纳米球的载体，首先将聚苯乙烯纳米球旋涂在玻璃基底上，然后通过热沉积的方法将金熔融沉积在聚苯乙烯纳米粒子的表面, 再通过超声的方式将负载有金纳米帽子的聚苯乙烯微球从玻璃基底上分离下来，最后用二氯甲烷将聚苯乙烯微球溶解掉，成功制备了空心的金纳米帽子材料。通过共价键链接的方式在这些空心的金纳米帽子的表面成功修饰上苯的衍生物，通过测试分析发现，修饰带有不同电性的基团，金纳米帽子的等离子体共振吸收会发生不同的红移或蓝移现象，推测这是由于金纳米帽子表面结构电子密度的变化所导致。     

空心微球结构Au/Ag合金泡沫块体的制备

将平均晶粒尺寸为4.6 nm的金粒子通过静电作用粘附于聚苯乙烯（PS）微球表面用于化学镀,化学镀金后PS表面的金沉积层几乎达到完全包覆,厚度70~90 nm;在Au/PS表面进行化学镀银,沉积的银颗粒堆积紧密,颗粒大小较先前沉积的金颗粒大,镀覆层厚度增厚至200~400 nm;模板去除后,获得了完全自支撑的Au40Ag60空心微球结构的圆柱状泡沫材料。制备的金银合金泡沫由直径约10 m的空心球壳组成,圆柱体直径约5 mm,密度约1.2 g/cm3。     

球壳结构金阴极及其X射线光电发射特性

以聚苯乙烯微球为模板, 采用种子-生长法在聚苯乙烯微球表面镀覆金球壳层, 以不同浓度旋涂分散在阴极衬底上, 热处理去除聚苯乙烯模板, 初步制备出表面具有金球壳结构的反射式金阴极样品, 通过金相显微镜和扫描电镜研究其表面形貌, 结果表明: 阴极表面球壳的直径约为10 μm, 高温去除聚苯乙烯微球模板后金沉积层具有良好的自支撑性, 球壳厚度约70-90 nm, 球壳表面主要由30-60 nm的晶粒突起组成. X射线光电发射测试表明, 反射式球壳结构阴极在200-1500 eV波段光电效率相对于平面薄膜阴极有明显提升, 其量子效率可达到平面阴极的3倍以上, 理论分析表明: 球壳结构阴极特殊的表面结构引起光电发射面积的增大和表面势垒的降低, 是阴极光电发射效率提高的主要原因.     

纳米 Au 球壳材料的制备及其近红外光热转换性质

报道了一种采用湿化学法,以Ag纳米球为模板合成纳米Au球壳水溶胶的新方法,并对这种材料的光热转换性质进行了研究。TEM分析表明,Au纳米颗粒呈球壳结构,粒径约为20nm,粒径分布比较均匀,无明显硬团聚体存在。随着氯金酸加入量的增加,Au球壳的吸收峰位置从可见区(-400nm)逐渐红移至近红外区(-800nm)。测量了不同浓度的Au球壳水溶胶经近红外激光照射后的温度变化。结果表明,经1．9W／mm^2的808nm近红外光照射10min,温度最高升高了5．5℃。由于800—1200nm是人体组织的透射窗口,肿瘤细胞在42℃左右即可被杀死,这种纳米Au球壳材料有望在利用光热转换的红外热疗中得到应用,并有可能利用光动力实现药物释放。     

中空结构Pt纳米粒子热稳定性和形变的分子动力学研究

不同于实心结构纳米粒子,中空结构Pt纳米粒子具有低密度、高孔隙率和大的比表面积等特点,具有特殊的物理化学性质,在催化、光电子和药物输送领域有重要的应用.纳米粒子热稳定性和形变特性对其合成、应用具有重要的影响.利用分子动力学模拟研究中空结构Pt纳米粒子结构稳定性和形变过程,对不同壳层厚度的Pt纳米粒子进行分析,结果表明:在弛豫过程,温度为0.1 K时,壳层厚度为0.5 nm的Pt纳米粒子结构将发生形变,壳层厚度为1 nm、1.5 nm、2.0 nm、2.5 nm和3 nm纳米粒子结构保持几乎不变;升温过程,中空结构Pt纳米粒子塌缩时对应的温度随着壳层厚度增加而升高;塌缩过程所经历的温度区间很窄,空心结构短时间内突变为实心结构,另外,中空结构纳米粒子塌缩后,内部原子重新排列,仍保持有序的fcc结构.     

Ag@Fe_3O_4@C-CdTe@SiO_2磁性荧光复合微球的制备与光学特征（英文）

先采用一步溶剂热法和水热法制备了碳包覆的Ag@Fe_3O_4核壳型磁性纳米粒子,然后通过表面氨基化改性后与巯基乙酸修饰的CdTe量子点反应,将量子点键合到磁性微球上,最后在其表面包覆上一层二氧化硅壳层,制备出具有荧光增强的Ag@Fe_3O_4@C-CdTe@SiO2磁性荧光复合材料。实验结果表明,该纳米粒子的平均粒径大约为150nm,磁饱和强度为224A/g(22.4emu/g),在室温下具有较好的磁性能。其中Ag@Fe_3O_4@C-CdTe磁性荧光纳米粒子的荧光强度大于Fe_3O_4@C-CdTe,其主要原因是内核为45nm的Ag纳米粒子具有表面等离子体共振作用,能够使其表面或附近的量子点荧光得到增强。     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Using sonochemistry for the fabrication of hollow ZnO microspheres

Hollow ZnO microspheres assembled by nanoparticles have been prepared by a sonochemical synthesis at room temperature using carbon spheres as template. The growth process of the precursor was investigated. The prepared hollow spheres were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HRTEM). The diameter of the obtained hollow spheres is about 500 nm, and the walls are composed of numerous ZnO aggregate nanocrystallines with diameters of 90 nm. A possible growth mechanism for the formation of ZnO microspheres has been proposed, in which carbon spheres play a crucial role in the formation of the wurtzite hollow ZnO microspheres. The specific structure of the hollow spheres may find applications in nanoelectronics, nanophotonics and nanomedicine.     

Fabrication of microporous hollow silica spheres templated by NP-10 micelles without calcinations

We reported a novel method to fabricate hollow silica microspheres using nonionic surfactant nonyl phenol ethoxylated decylether (NP-10) micelles as template, n-octadecane as core and sodium silicate as silica precursor. The core materials were removed by ethanol during the reaction. Hollow structure formed without calcinations or chemical etching. Hierarchical silica hollow microspheres were prepared by changing the concentration of the reactants and reaction time. Size of the core materials was obtained from the temperature-dependent dynamic light scattering (DLS) measurement. Scanning election microscopy (SEM) and transmission electron microscopy (TEM) results revealed that ordered microporous hollow silica microspheres with thickness of shell about 200 nm and mean diameter 2.5 μm were prepared. Porosity and pore size were analyzed by Brunauer-Emmett-Teller (BET).     

Synthesis of ZnO hollow spherical structures with different surface-to-volume ratios

ZnO hollow spherical structures with different surface-to-volume ratios were prepared using solid Zn microspheres as template via a simple oxygen-controlled thermal evaporation approach. The results of scanning electron microscopy testify that ZnO hollow spherical structures with different morphologies can be realized by changing oxygen supply. The corresponding transmission electron microscopy images further reveal that the prepared spherical structures are hollow, and nanorods epitaxially grow from the surface of the sphere shell along the [0001] direction. A series of experiments indicates that the formation of hollow spherical structures involves the oxidization on the surface of Zn microspheres, sublimation of Zn, and growth of ZnO nanorods.     

微乳液聚合制备纳米银/聚苯乙烯复合材料

采用柠檬酸钠为稳定剂、聚乙烯吡咯烷酮为分散剂,以水合肼还原银氨络离子制备出稳定的单分散胶态纳米银。以制得的纳米银溶胶,通过正相微乳液聚合,制备纳米银/聚苯乙烯复合材料。利用紫外-可见光(UV-Vis)吸收光谱研究了纳米银的光吸收特性,采用X射线衍射(XRD)和透射电镜(TEM)对产物的晶体结构、形貌及尺寸进行了分析。结果表明:所制得的银纳米颗粒属立方晶系,平均粒径约10 nm,且无团聚及氧化现象;聚合过程中,纳米银的晶体结构、形貌及尺寸未发生明显变化。凝胶渗透色谱(GPC)分析表明聚苯乙烯基体重均分子量达4.03106,分子量分布指数为1.21;热重-示差扫描量热(TG-DSC)分析表明所制备的复合材料具有优异的热稳定性。     

聚苯乙烯单层空心微球掺硫层不均匀结构研究

采用红外显微图像技术对单层掺硫空心微球上出现的不均匀结构进行了表征分析,证明了不均匀结构的产生来源于掺硫剂PSS（聚苯乙烯磺酸钠）。同时对PSS的成膜性能进行了研究,并使用红外显微图像技术和偏光显微镜对PSS平面薄膜进行表征,结果表明,掺硫剂PSS成膜性能较差,薄膜表面存在分子有序化聚集体和结晶现象。热处理结果显示PSS薄膜与聚苯乙烯薄膜热性能相差较大,易产生脆性开裂并从聚苯乙烯表面剥离,说明PSS不适合于高掺硫量微球制备。     

Immobilization of silver nanoparticles on silica microspheres

The silver nanoparticles (Ag NPs) have been immobilized onto silica microspheres through the adsorption and subsequent reduction of Ag⁺ ions on the surfaces of the silica microspheres. The neat silica microspheres that acted as the core materials were prepared through sol–gel processing; their surfaces were then functionalized using 3-mercaptopropyltrimethoxysilane (MPTMS). The major aims of this study were to immobilize differently sized Ag particles onto the silica microspheres and to understand the mechanism of formation of the Ag nano-coatings through the self-assembly/adsorption behavior of Ag NPs/Ag⁺ ions on the silica spheres. The obtained Ag NP/silica microsphere conglomerates were characterized by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and energy-dispersive spectroscopy (EDS). Their electromagnetic wave shielding effectiveness were also tested and studied. The average particle size of the obtained Ag NPs on the silica microsphere was found that could be controllable (from 2.9 to 51.5 nm) by adjusting the ratio of MPTMS/TEOS and the amount of AgNO₃.     

二维氧化锌纳米阵列的制备及光学吸收特性研究

采用漂移法,在玻璃衬底上制备出粒径分别为117,350和500 nm单层、大面积的聚苯乙烯胶体球掩膜板,在已制得的掩膜板上用射频磁控溅射的方法沉积一层氧化锌薄膜,最后用有机溶液四氢呋喃(THF)浸泡去除聚苯乙烯胶体球,获得不同粒径的二维氧化锌纳米团簇。通过扫描电子显微镜和能量色散X射线光谱仪对样品的形貌及成份进行表征,表明所制得样品为有序分布的蜂窝网状氧化锌纳米阵列。在室温下,通过吸收光谱仪测试样品在300～800 nm波长范围内的吸收光谱,结果表明对于具有不同尺寸晶粒的氧化锌纳米团簇样品,随着所采用的聚苯乙烯胶体球粒径的增大,即氧化锌纳米团簇粒径的增加,光吸收峰出现了宽化和红移;随着溅射时间的延长,即氧化锌薄膜膜厚的增加,光吸收率提高。此外,对氧化锌纳米团簇阵列的光吸收特性进行了基于离散偶极子近似的理论计算从而获得任意形状和尺寸粒子的吸收。目前,文献报道中用此理论计算各种形状的纳米金、银等金属的结果与实验结果相符,但是应用离散偶极子的近似理论计算氧化锌纳米颗粒的报道很少。应用此理论计算三角棱台形状的氧化锌光学吸收特性,根据氧化锌薄膜介电常数和膜厚的变化进行光吸收特性的模拟,并解释了实验结果。