Physical and electrical characteristics of a high-k Yb2O3 gate dielectric

High-k ytterbium oxide (Yb₂O₃) gate dielectrics were deposited on Si substrate by reactive sputtering. The structural features of these films after postdeposition annealing treatment were studied by X-ray diffraction and X-ray photoelectron spectroscopy. It is found that the Yb₂O₃ gate dielectrics annealed at 700 °C exhibit a larger capacitance value, a lower frequency dispersion and a smaller hysteresis voltage in C-V curves compared with other annealing temperatures. They also show negligible charge trapping under high constant voltage stress. This phenomenon is mainly attributed to the decrease in the amorphous silica thickness.     

Martensitic transformation and magnetic properties of ferromagnetic shape memory Fe66Pd30Rh4 alloys

This study mainly shows that in the Fe₆₆Pd₃₀Rh₄ (at%) alloys, the L1₀ phase plays an important role in magnetostriction due to the interplay of L1₀ martensitic twins with magnetic domains. The L1₀ martensitic twin structure exhibits a strong magnetocrystalline anisotropy energy constant (K_u=1.27-2.84×10⁶ (ergs/cm³)) along the tetragonal c axis direction. In addition, the L1₀ tetragonal martensitic twin structure shows both a perfect shape memory and a reversible shape memory effect; therefore, it is expected to be applicable in magneto-mechanical applications (such as microactuators or springs). However, in this study, we discover that solution treatment (ST) and aging heat treatments of Fe₆₆Pd₃₀Rh₄ ferromagnetic shape memory alloys influence the behavior of the martensitic transition, which is associated with the change in magnetic properties. The process of a thermoelastic L1₀+L1_m twin phase decomposition→non-thermoelastic L1₀+L1_m+α_bct structure in Fe₆₆Pd₃₀Rh₄ alloys during solution treatment and aging at 400-550 °C for various times is studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The relation of phase separation morphology to the magnetic property change is examined with a superconducting quantum interference device (SQUID) magnetometer, and magnetostriction measurement is performed with a strain gage method and magnetostrictive meter setup. The results indicate that the process of martensitic transformation during aging leads to an increase in coercivity and a decrease in magnetostriction, simultaneously.     

The up-conversion properties of Yb and Er doped Y4Al2O9 phosphors

Er³⁺ doped and Yb³⁺/Er³⁺ co-doped Y₄Al₂O₉ phosphors are prepared by the sol-gel method. The effect of dopant concentration on the structure and up-conversion properties is investigated by X-ray diffraction (XRD) and photoluminescence, respectively. XRD pattern indicates that the sample structure belongs to monoclinic. Under 980 nm excitation, the green and red up-conversion emissions are observed and the emission intensities depended on the Yb³⁺ ion concentration. The green up-conversion emissions decrease with the increase of Yb³⁺ concentration, while red emission increases as Yb³⁺ concentration increases from 0 to 8 at% and then decreases at high Yb³⁺ concentration. The mechanisms of the up-conversion emissions are discussed and results shows that in Er³⁺ and Yb³⁺/Er³⁺ co-doped system, cross-relaxation (CR) and energy transfer (ET) processes play an important role for the green and red up-conversion emissions.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Yb2.75C60价带光电子能谱

用角积分紫外光电子能谱技术测量了Yb_2.75C₆₀薄膜的价带电子态密度分布.相纯Yb_2.75C₆₀样品通过C1s芯态x射线电子谱峰的位移表征.结果表明Yb_2.75C₆₀是半导体，在费米能级处几乎没有电子态分布.Yb 6s电子态和C₆₀LUMO能带的杂化效应不可忽略，有部分Yb 6s电子分布在Yb-C₆₀杂化能带上. 关键词： 2.75C₆₀')" href="#">Yb_2.75C₆₀ 电子能谱 电子态密度     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Growth and optical properties of Yb and Tb codoped BaB2O4 crystals

Optical absorption and luminescence spectra of ytterbium and terbium codoped BaB₂O₄ (β-BBO and α-BBO) crystals grown in different conditions have been studied. Low-temperature absorption peaks were observed in all samples. Features related to rare earth ions were observed in absorption and luminescence spectra. Absorption and emission in the range 860-1000 nm are caused by ²F_5/2↔²F_7/2 transitions in Yb³⁺ ions. Emission peaks at 500, 550, 590 and 630 nm correspond to ⁵D₄→⁷F₆, ⁷F₅, ⁷F₄, and ⁷F₃ transitions of Tb³⁺ ions, respectively. The probable reasons of variations in spectroscopic features related to Yb in BBO host are discussed. It has been shown that the replacement of Ва²⁺ by Yb³⁺ in the lattice of ВаВ₂О₄ results in the decrease in the symmetry of oxygen surrounding of Yb³⁺.     

Group delay dispersion measurement of Yb:YAl3(BO3)4 crystal with white-light interferometry

We report the group delay dispersion of Yb³⁺:YAl₃(BO₃)₄ (Yb:YAB) crystal measured by a white-light interferometer, and compare with that calculated from the Sellmeier formulae provided by the crystal supplier, over the wavelength range from 1000 nm to 1080 nm. The data should be useful for the dispersion compensation for femtosecond pulse generation in Yb:YAB lasers.     

Optical properties of Mn-activated Na2SnF6 and Cs2SnF6 red phosphors

Alkaline hexafluorostantanate red phosphors Na₂SnF₆:Mn⁴⁺ and Cs₂SnF₆:Mn⁴⁺ are synthesized by chemical reaction in HF/NaMnO₄ (CsMnO₄)/H₂O₂/H₂O mixed solutions immersed with tin metal. X-ray diffraction patterns suggest that the synthesized phosphors have a tetragonal symmetry with the space group D_4h¹⁴ (Na₂SnF₆:Mn⁴⁺) and a trigonal symmetry with the space group D_3d³ (Cs₂SnF₆:Mn⁴⁺). Photoluminescence (PL) analysis, PL excitation (PLE) spectroscopy, and the Raman scattering techniques are used to investigate the optical properties of the phosphors. The Franck-Condon analysis of the PLE data yields the Mn⁴⁺-related optical transitions to occur at ∼2.39 and ∼2.38 eV (⁴A_2g→⁴T_2g) and at ∼2.83 and ∼2.76 eV (⁴A_2g→⁴T_1g) for Na₂SnF₆:Mn⁴⁺ and Cs₂SnF₆:Mn⁴⁺, respectively. The crystal field parameters (Dq) of the Mn⁴⁺ ions in the Na₂SnF₆ and Cs₂SnF₆ hosts are determined to be ∼1930 and ∼1920 cm⁻¹, respectively. Temperature-dependent PL measurements are performed from 20 to 440 K in steps of 10 K, and the obtained results are interpreted by taking into account the Bose-Einstein occupation factor. Comprehensive discussion is given on the phosphorescent properties of a family of Mn⁴⁺-activated alkaline hexafluoride salts.     

Stabilization of a very high-k crystalline ZrO2 phase by post deposition annealing of atomic layer deposited ZrO2/La2O3 dielectrics on germanium

The impact of the ZrO₂/La₂O₃ film thickness ratio and the post deposition annealing in the temperature range between 400 °C and 600 °C on the electrical properties of ultrathin ZrO₂/La₂O₃ high-k dielectrics grown by atomic layer deposition on (1 0 0) germanium is investigated. As-deposited stacks have a relative dielectric constant of 24 which is increased to a value of 35 after annealing at 500 °C due to the stabilization of tetragonal/cubic ZrO₂ phases. This effect depends on the absolute thickness of ZrO₂ within the dielectric stack and is limited due to possible interfacial reactions at the oxide/Ge interface. We show that adequate processing leads to very high-k dielectrics with EOT values below 1 nm, leakage current densities in the range of 0.01 A/cm², and interface trap densities in the range of 2-5 × 10¹² eV⁻¹ cm⁻².     

Structural and optical properties of Er, Yb co-doped Y2O3 thin films

Thin Er³⁺, Yb³⁺ co-doped Y₂O₃ films were grown on (1 0 0) YAG substrates by pulsed laser deposition. Ceramic targets having different active ion concentration were used for ablation. The influence of the rare-earth content and oxygen pressure applied during the deposition on the structural, morphological and optical properties of the films were investigated. The films deposited at the lower pressure, 1 Pa, and at 1/10 Er to Yb doping ratio are highly textured along the (1 1 1) direction of the Y₂O₃ cubic phase. In addition to the crystalline structure, these films possess smoother surface compared to those prepared at the higher pressure, 10 Pa. All other films are polycrystalline, consisting of cubic and monoclinic phases of Y₂O₃. The rougher surface of the films produced at the higher-pressure leads to higher scattering losses and different behavior of the reflectivity spectra. Optical anisotropy in the films of less than 0.004 was measured regardless of the monoclinic structure obtained. Waveguide losses of about 1 dB/cm at 633 nm were obtained for the films produced at the lower oxygen pressure.     

Study of the fabrication parameters of large core Yb2O3 doped optical fibre through solution doping technique

Double clad large core Yb₂O₃ doped fibres with core diameter up to 20 μm have been fabricated by the solution doping technique through deposition of multiple porous core layers. The process parameters have been optimized with respect to the uniform doping of Al₂O₃ and Yb₂O₃ within the large core preform through soaking of the deposited multiple porous layers of fixed SiO₂-P₂O₅ composition with an alcoholic solution of a mixture of suitable strength of AlCl₃·6H₂O and YbCl₃·6H₂O to get the desired low NA around 0.09-0.11. The most critical parameters associated in this process are the deposition temperature with respect to uniform deposition of un-sintered layers of equal thickness with suitable porosity, viscosity of the soaking solution, pre-sintering temperature, proper mixing of the inlet gas mixture as well as proper drying of the thick porous layer after solution soaking process. This investigation will be very useful for development of large core Yb₂O₃ doped laser fibre technology.     

Magnetic order and crystal field in Dy2Ru2O7 and Yb2Ru2O7

The magnetic properties of R₂Ru₂O₇ pyrochlore compounds (R=Yb, Dy) were studied using specific heat down to 0.4 K and bulk magnetic measurements. These two rare-earth elements were chosen to demonstrate the effect of Ru-R exchange interaction on R magnetic sublattice, in two cases of anisotropy: axial in Dy and planar in Yb. Dy₂Ru₂O₇ undergoes a second order transition to a fully ordered state at 1.85 K with no signs of the spin-ice state. In Yb₂Ru₂O₇ the Yb sublattice orders gradually around 8 K due to the Ru molecular field and no further transition is observed down to 0.4 K. Including the Ru molecular field at the R site in calculations based on crystal field parameters known from titanates R₂Ti₂O₇, allowed us to interpret experimental data.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Yb effect on the spectroscopic properties of Er-Yb codoped SnO2 thin films

We have investigated the optical properties of sol-gel thin films of tin dioxide (SnO₂) codoped with Er³⁺-Yb³⁺ as a function of Yb³⁺ concentration. The Judd-Ofelt model has been applied to absorption intensities of Er³⁺ (4f¹¹) transitions to establish the so-called Judd-Ofelt intensity parameters: Ω₂, Ω₄, Ω₆. Various spectroscopic parameters were obtained to evaluate their dependence and the potential of the samples as a laser material in the eye-safe laser wavelength (1.53 μm) as a function of Yb³⁺ concentration. An amelioration of the quality factor Ω₄/Ω₆ was found with Yb content. Both the IR photoluminescence (PL) intensity and the up-conversion emission, from Er³⁺ ion in SnO₂, were found to increase with Yb concentration. We show that the Yb³⁺ ion acts as sensitizer for Er³⁺ ion and contributes largely to the improvement of the spectroscopic properties of SnO₂:Er. The mechanism of up-conversion emission is discussed and a model is proposed. The results showed that sol-gel SnO₂ is promising gain media for developing the solid-state 1.5 μm optical amplifiers and tunable up-conversion lasers.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

AgSbSe2 and AgSb(S,Se)2 thin films for photovoltaic applications

Silver antimony selenide (AgSbSe₂) thin films were prepared by heating sequentially deposited multilayers of antimony sulphide (Sb₂S₃), silver selenide (Ag₂Se), selenium (Se) and silver (Ag). Sb₂S₃ thin film was prepared from a chemical bath containing SbCl₃ and Na₂S₂O₃, Ag₂Se from a solution containing AgNO₃ and Na₂SeSO₃ and Se thin films from an acidified solution of Na₂SeSO₃, at room temperature on glass substrates. Ag thin film was deposited by thermal evaporation. The annealing temperature was 350 °C in vacuum (10⁻³ Torr) for 1 h. X-ray diffraction analysis showed that the thin films formed were polycrystalline AgSbSe₂ or AgSb(S,Se)₂ depending on selenium content in the precursor films. Morphology and elemental analysis of these films were done using scanning electron microscopy and energy dispersive X-ray spectroscopy. Optical band gap was evaluated from the UV-visible absorption spectra of these films. Electrical characterizations were done using Hall effect and photocurrent measurements. A photovoltaic structure: glass/ITO/CdS/AgSbSe₂/Al was formed, in which CdS was deposited by chemical bath deposition. J-V characteristics of this structure showed V_oc = 435 mV and J_sc = 0.08 mA/cm² under illumination using a tungsten halogen lamp. Preparation of a photovoltaic structure using AgSbSe₂ as an absorber material by a non-toxic selenization process is achieved.     

Gd-doped SnO2 nanoparticles: Structure and magnetism

Gd-doped SnO₂ nanoparticles were chemically prepared doping 0-12.5% Gd into SnO₂ and calcined at 600 °C. X-ray diffraction and Fourier transformed infrared spectroscopy measurements show the formation of single phase of Sn_1−xGd_xO₂ up to x=0.0625 while at x=0.125, an additional secondary phase of tetragonal GdO₂ (not cubic Gd₂O₃) is detected. The transmission electron microscopy studies show that the individual particles are single crystalline with an average size in the range of 10-12 nm. Magnetization measurements show the absence of ferromagnetic and antiferromagnetic ordering in all samples; however surface spin effects and enhanced Gd-O-Gd interactions are proposed to account for the observed magnetic properties of the samples.     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.