Room temperature synthesis of water-repellent polystyrene nanocomposite coating

A stable superhydrophobic polystyrene nanocomposite coating was fabricated by means of a very simple and easy method. The coating was characterized by scanning electron microscopy and X-ray photoelectron spectrum. The wettability of the products was also investigated. By adding the surface-modified SiO₂ nanoparticles, the wettability of the coating changed to water-repellent superhydrophobic, not only for pure water, but also for a wide pH range of corrosive liquids. The influence of the drying temperature and SiO₂ content on the wettability of the nanocomposite coating was also investigated. It was found that both factors had little or no significant effect on the wetting behavior of the coating surface.     

The super hydrophobicity of ZnO nanorods fabricated by electrochemical deposition method

Electrochemical deposition method was employed to fabricate ZnO nanorods on zinc foil substrate in this paper. The structural observations of ZnO nanorods with different aspect ratios were carried out by field-emission scanning electron microscopy. The microstructures of ZnO nanorods were also characterized by X-ray diffraction and the changes in surface hydroxyls with electrochemical deposition time were analyzed by X-ray photoelectron spectroscopy. The study results show the aspect ratios of ZnO nanorods and the density of their surface hydroxyls are responsible for their superhydrophobicity. The fluorinated polymer coated ZnO nanorods showed an excellent superhydrophobic behavior with 167° contact angle of water droplet, which is larger than that of fluorinated polymer flat surface. The more the surface hydroxyls are, the more hydrophilic the surfaces are. Meanwhile, the larger the aspect ratio of ZnO nanorod arrays is, the larger its drophobicity is. The results of this study might pave a simple and feasibility pathway to the fabrication of superhydrophobic cleaning materials used in engineering fields.     

微纳复合结构表面稳定润湿状态及转型过程的热力学分析

自然界中的微纳复合结构超疏水表面由于其独特的润湿性质引起了人们的广泛关注, 大量实验研究表明了仿生人工微纳复合结构表面润湿性能的优越性, 然而液滴在微纳复合结构表面的润湿状态和转型过程的理论研究还并不完善. 本文首先用热力学方法分析了液滴在微纳复合结构表面可能存在的所有状态(四种稳定润湿状态和五种亚稳态到稳定态转型中的过渡态), 推导出了相应的能量表达式及表观接触角方程; 基于最小能量原理, 确定液滴在微纳复合结构表面的稳定状态, 较以往模型相比, 能够更好的预测已有的实验结果; 其次研究了微纳结构尺寸对稳定润湿状态和亚稳态到稳定态转型过程的影响; 最后提出了微纳复合结构表面设计原则, 即确定“超疏水稳定区”尺寸范围, 为超疏水表面的制备提供理论依据.     

Fabrication of superhydrophobic surfaces on zinc substrates and their application as effective corrosion barriers

Stable superhydrophobic surfaces have been effectively fabricated on the zinc substrates through one-step platinum replacement deposition process without the further modification or any other post processing procedures. The effect of reaction temperatures on the surface morphology and wettability was studied by using SEM and water contact angle (CA) analysis. Under room temperature, the composite structure formed on the zinc substrate was consisted of microscale hexagonal cavities, densely packed nanoparticles layer and micro/nanoscale structures like the flowers. The structure has exhibited great surface roughness and porosity contributing to the superhydrophobicity where the contact angle could reach an ultra high value of around 170°. Under reaction temperature of 80 °C, the composite structure, on the other hand, was hierarchical structure containing lots of nanoscale flowers and some large bushes and showed certain surface roughness (maximum CA value of about 150°). In addition, an optimal superhydrophobic platinum surface was able to provide an effective anticorrosive coating to the zinc substrate when it was immersed into an aqueous solution of sodium chloride (3% NaCl) for up to 20 days. The corrosion process was monitored through electrochemical means and the results are compared with those of unprotected zinc plates.     

Superhydrophobic and icephobic surfaces prepared by RF-sputtered polytetrafluoroethylene coatings

A superhydrophobic and icephobic surface were investigated on aluminum alloy substrate. Anodizing was used first to create a micro-nanostructured aluminum oxide underlayer on the alloy substrate. In a second step, the rough surface was coated with RF-sputtered polytetrafluoroethylene (PTFE or Teflon^®). Scanning electron microscopy images showed a “bird's nest”-like structure on the anodized surface. The RF-sputtered PTFE coating exhibited a high static contact angle of ∼165° with a very low contact angle hysteresis of ∼3°. X-ray photoelectron spectroscopy (XPS) results showed high quantities of CF₃ and CF₂ groups, which are responsible for the hydrophobic behavior of the coatings. The performance of this superhydrophobic film was studied under atmospheric icing conditions. These results showed that on superhydrophobic surfaces ice-adhesion strength was 3.5 times lower than on the polished aluminum substrate.     

Superhydrophobic wind turbine blade surfaces obtained by a simple deposition of silica nanoparticles embedded in epoxy

Samples of wind turbine blade surface have been covered with a superhydrophobic coating made of silica nanoparticles embedded in commercial epoxy paint. The superhydrophobic surfaces have a water contact angle around 152°, a hysteresis less than 2° and a water drop sliding angle around 0.5°. These surfaces are water repellent so that water drops cannot remain motionless on the surface. Examination of coated and uncoated surfaces with scanning electron microscopy and atomic force microscopy, together with measurements of water contact angles, indicates that the air trapped in the cavity enhances the water repellency similarly to the lotus leaf effect. Moreover, this new coating is stable under UVC irradiation and water pouring. The production of this nanoscale coating film being simple and low cost, it can be considered as a suitable candidate for water protection of different outdoor structures.     

Fabrication of a superhydrophobic ZnO nanorod array film on cotton fabrics via a wet chemical route and hydrophobic modification

A superhydrophobic ZnO nanorod array film on cotton substrate was fabricated via a wet chemical route and subsequent modification with a layer of n-dodecyltrimethoxysilane (DTMS). The as-obtained cotton sample was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), scanning probe microscope (SPM) and X-ray photoelectron spectroscopy (XPS), respectively. The wettability of the cotton fabric sample was also studied by contact angle measurements. The modified cotton fabrics exhibited superhydrophobicity with a contact angle of 161° for 8 μL water droplet and a roll-off angle of 9° for 40 μL water droplet. It was shown that the proper surface roughness and the lower surface energy both played important roles in creating the superhydrophobic surface, in which the Cassie state dominated.     

Fabrication of a superhydrophobic surface on a wood substrate

A layer of lamellar superhydrophobic coating was fabricated on a wood surface through a wet chemical process. The superhydrophobic property of the wood surface was measured by contact angle (CA) measurements. The microstructure and chemical composition of the superhydrophobic coating were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). An analytical characterization revealed that the microscale roughness of the lamellar particles was uniformly distributed on the wood surface and that a zinc stearate monolayer (with the hydrophobic groups oriented outward) formed on the ZnO surface as the result of the reaction between stearic acid and ZnO. This process transformed the wood surface from hydrophilic to superhydrophobic: the water contact angle of the surface was 151°, and the sliding angle was less than 5°.     

Superhydrophobic iron material surface with flower-like structures obtained by a facile self-assembled monolayer

A simple and economical route based on a K₂CO₃ mediated process was developed to synthesize three-dimensional (3D) flower-like Fe₃O₄ micro/nanoflakes on the surface of iron plates by a direct in-situ hydrothermal synthesis method. The prepared micro/nanoflakes were characterized by X-ray diffraction and scanning electron microscopy. It was found that the width of the nanoflakes ranges from 50 to 100 nm, and the length of the flakes is about 3 μm. The morphology of Fe₃O₄ nanostructures can be tuned from simple isolated nanoflakes to the ordered 3D flower-like shape by increasing the reaction temperature. The wettability of the surface with 3D flower-like micro/nanoflakes was changed from hydrophilicity to superhydrophobicity by chemical modification with vinyl tirethoxy-silane. The static contact angles for water on both of the modified surfaces were larger than 150°, which was closely related to the chemical modification and hierarchical structure. Furthermore, the surfaces retained good superhydrophobic stability in long-term storage as well, which should be critical to the application of iron materials in engineering.     

Field-emission enhancement of molybdenum oxide nanowires with nanoprotrusions

The field-emission properties of molybdenum oxide nanowires grown on a silicon substrate and its emission performance in various vacuum gaps are reported in this article. A new kind of molybdenum oxides named nanowires with nanoscale protrusions on their surfaces were grown by thermal vapor deposition with a length of ~1 μm and an average diameter of ~50 nm. The morphology, structure, composition and chemical states of the prepared nanostructures were characterized by scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). According to XRD, XPS, and TEM analyses, the synthesized samples were composed of MoO₂ nanowires formed over a thin layer of crystalline Mo₄O₁₁. TEM observation revealed that these nanowires have some nanoscale protrusion on their surface. These nanoprotrusions resulted in enhancement of field-emission properties of nanowires comprising nanoprotrusions. The turn-on emission field and the enhancement factor of this type of nanostructures were measured 0.2 V/μm and 42991 at the vacuum gap of 300 μm, respectively. These excellent emission properties are attributed to the special structure of the nanowires that have potential for utilizing in vacuum nanoelectronic and microelectronic applications.