Spin-wave resonances in Eu<Subscript>0.8</Subscript>Ce<Subscript>0.2</Subscript>Mn<Subscript>2</Subscript>O<Subscript>5</Subscript> and EuMn<Subscript>2</Subscript>O<Subscript>5</Subscript> multiferroics

Spin-wave resonances have been observed in superlattices arising due to the phase separation and self-organization of charge carriers in Eu_0.8Ce_0.2Mn₂O₅ single crystals. The resonances are found within the 5–80 K temperature range at frequencies close to 30 GHz. Similar resonances with intensities about an order of magnitude lower are also observed in EuMn₂O₅. The latter suggests the existence of charge transfer processes between the manganese ions of different valences in EuMn₂O₅.     

Phase transition in Bi<Subscript>8</Subscript>Fe<Subscript>6</Subscript>Ti<Subscript>3</Subscript>O<Subscript>27</Subscript> multiferroic ceramics

The polycrystalline Bi₈Fe₆Ti₃O₂₇ compound was prepared by a high-temperature solid-state reaction technique. Preliminary structural analysis by X-ray diffraction (XRD) confirms the formation of a single-phase compound in an orthorhombic crystal system at room temperature. The elemental content of the compound was analyzed by EDAX microanalysis. Microstructural analysis by scanning electron microscopy (SEM) shows that the compound has well defined grains, which are distributed uniformly throughout the surface of the pellet sample. Detailed studies of temperature-dependent dielectric response at various frequencies show dielectric anomalies at 380, 389 and 403°C for 10 kHz, 100 kHz, and 1 MHz respectively. The hysteresis loop observed by applying an electric field of 12 kV/cm on the poled sample with smaller remanent polarization supports the existence of ferroelectricity in this material. The value of d₃₃ of the compound was found to be 19 pC/N.      

Integrated investigation of the Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> phase stability

The Li₄Ti₅O₁₂ is applied in lithium ion batteries as anode material, which can be synthesized by various synthesis techniques. In this study, the molten salt synthesis technique at low temperatures, i.e. 350 °C, was applied to synthesize Li₄Ti₅O₁₂. Surprisingly, the Li₄Ti₅O₁₂ was not formed according to XRD analysis, which raised question about the stability range of Li₄Ti₅O₁₂. To investigate the stability of Li₄Ti₅O₁₂ at low temperatures, the high-temperature calcined Li₄Ti₅O₁₂ powder was equilibrated in the LiCl-KCl eutectic salt at 350 °C. The result of experiment revealed that the Li₄Ti₅O₁₂ is not decomposed. Results of ab initio calculations also indicated that the Li₄Ti₅O₁₂ phase is a stable phase at 0 K. The products of molten salt synthesis technique were then annealed at 900 °C, which resulted in the Li₄Ti₅O₁₂ formation. It was concluded that the Li₄Ti₅O₁₂ is a stable phase at low temperatures and the reasons for not forming the Li₄Ti₅O₁₂ by molten salt technique at low temperature are possibly related to activation energy and kinetic barriers. The Li₄Ti₅O₁₂ formation energy is also very small, due to the results of ab initio calculations.     

Ferroelectric and dielectric properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> thin films grown on Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> film layer

Ferroelectric and dielectric properties of bilayered ferroelectric thin films, SrBi₄Ti₄O₁₅ grown on Bi₄Ti₃O₁₂, were investigated. The thin films were annealed at 700°C under oxygen atmosphere. The bilayered thin films were prepared on a Pt(111)/Ti/SiO₂/Si substrate by a chemical solution deposition method. The dielectric constant and dielectric loss of the bilayered thin films were 645 and 0.09, respectively, at 100 kHz. The value of remnant polarization (2P _r) measured from the ferroelectric thin film capacitors was 60.5 μC/cm² at electric field of 200 kV/cm. The remnant polarization was reduced by 22% of the initial value after 10¹⁰ switching cycles. The results showed that the ferroelectric and dielectric properties of the SrBi₄Ti₄O₁₅ on Bi₄Ti₃O₁₂ ferroelectric thin films were better than those of the SrBi₄Ti₄O₁₅ grown on a Pt-coated Si substrate suggesting that the improved properties may be due to the different nucleation and growth kinetics of SrBi₄Ti₄O₁₅ on the c-axis-oriented Bi₄Ti₃O₁₂ layer or on the Pt-coated Si substrate.     

Multiple magnetic transitions in single crystals of Ce<Subscript>12</Subscript>Fe<Subscript>57.5</Subscript>As<Subscript>41</Subscript> and La<Subscript>12</Subscript>Fe<Subscript>57.5</Subscript>As<Subscript>41</Subscript>

Measurements of magnetic and transport properties were performed on needle-shaped single crystals of Ce₁₂Fe_57.5As₄₁ and La₁₂Fe_57.5As₄₁. The availability of a complete set of data enabled a side-by-side comparison between these two rare earth compounds. Both compounds exhibited multiple magnetic orders within 2–300 K and metamagnetic transitions at various fields. Ferromagnetic transitions with Curie temperatures of 100 and 125 K were found for Ce₁₂Fe_57.5As₄₁ and La₁₂Fe_57.5As₄₁, respectively, followed by antiferromagnetic type spin reorientations near Curie temperatures. The magnetic properties underwent complex evolution in the magnetic field for both compounds. An antiferromagnetic phase transition at about 60 K and 0.2 T was observed merely for Ce₁₂Fe_57.5As₄₁. The field-induced magnetic phase transition occurred from antiferromagnetic to ferromagnetic structure. A strong magnetocrystalline anisotropy was evident from magnetization measurements of Ce₁₂Fe_57.5As₄₁. A temperature-field phase diagram was present for these two rare earth systems. In addition, a logarithmic temperature dependence of electrical resistivity was observed in the two compounds within a large temperature range of 150–300 K, which is rarely found in 3D-based compounds. It may be related to Kondo scattering described by independent localized Fe 3d moments interacting with conduction electrons.     

AlF<Subscript>3</Subscript> coating of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> for high-performance Li-ion batteries

AlF₃-coating is attempted to improve the performance of LiNi_0.5Mn_1.5O₄ cathode materials for Li-ion batteries. The prepared powders are characterized by scanning electron microscope, powder X-ray diffraction, charge/discharge, and impedance. The coated LiNi_0.5Mn_1.5O₄ samples show higher discharge capacity, better rate capability, and higher capacity retention than the uncoated samples. Among the coated samples, 1.0 mol% AlF₃-coated sample shows highest capacity after charge–discharged at 30 mA/g for 3 cycles, but 4.0 mol% coated sample exhibits the highest capacity and cycling stability when cycled at high rate of 150 and 300 mA/g. The 40th cycle discharge capacity at 300 mA/g current still remains 114.8 mAh/g for 4.0 mol% AlF₃-coated LiNi_0.5Mn_1.5O₄, while only 84.3 mAh/g for the uncoated sample.     

Modification research of LiAlO<Subscript>2</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> as a cathode material for lithium-ion battery

The LiNi_0.8Co_0.1Mn_0.1O₂ with LiAlO₂ coating was obtained by hydrolysis–hydrothermal method. The morphology of the composite was characterized by SEM, TEM, and EDS. The results showed that the LiAlO₂ layer was almost completely covered on the surface of particle, and the thickness of coating was about 8–12 nm. The LiAlO₂ coating suppressed side reaction between composite and electrolyte; thus, the electrochemical performance of the LiAlO₂-coated LiNi_0.8Co_0.1Mn_0.1O₂ was improved at 40 °C. The LiAlO₂-coated sample delivered a high discharge capacity of 181.2 mAh g^?1 (1 C) with 93.5% capacity retention after 100 cycles at room temperature and 87.4% capacity retention after 100 cycles at 40 °C. LiAlO₂-coated material exhibited an excellent cycling stability and thermal stability compared with the pristine material. These works will contribute to the battery structure optimization and design.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Giant positive magnetoresistance in heterostructure (La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript>) coated with YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7</Subscript> composites

(La_0.7Sr_0.3MnO₃) _x /(YBa₂Cu₃O₇) _y composites were prepared by mixing La_0.7Sr_0.3MnO₃ powders and the sol–gel-derived YBa₂Cu₃O₇ matrix, followed by high-temperature calcinations. Their structural, magnetic properties and magnetoresistance effect have been investigated systematically. A giant positive magnetoresistance (PMR) at low magnetic field is observed at low temperatures. In the case of (La_0.7Sr_0.3MnO₃)₁/(YBa₂Cu₃O₇)₉ composite, the PMR achieves 260% under a magnetic field of 5800 Oe. However, the PMR value sharply decreases with increasing temperature and no magnetoresistance effects are found above metal-insulator transition temperature. The enhancement of spin-dependent scattering at the grain boundaries should be responsible for the observed PMR. In addition, the temperature dependence of resistance under magnetic field could be explained by the competition between diamagnetism and paramagnetism in YBCO phase. At low temperature, the diamagnetism is predominant over paramagnetism and the interface scattering between LSMO grains is enhanced correspondingly. As a result, the low-temperature resistance increases and large PMR appears.     

Magnetocaloric effect in (La<Subscript>0.6</Subscript>Ca<Subscript>0.4</Subscript>)<Subscript>0.9</Subscript>Mn<Subscript>1.1</Subscript>O<Subscript>3</Subscript>

The results of investigations of the magnetization, susceptibility, and magnetic-field-induced changes in the entropy of polycrystalline manganite (La_0.6Ca_0.4)_0.9Mn_1.1O₃ near the magnetic phase transition have been presented. Magnetic measurements have been carried out at temperatures in the range from 210 to 310 K in magnetic fields of up to 9 T. The magnetocaloric effect has been revealed by measuring the magnetic-field dependences of magnetization. The magnitude of the magnetocaloric effect is compared with similar results obtained for other manganites.     

Two-dimensional antiferromagnetic correlations in an La<Subscript>1.4</Subscript>Sr<Subscript>1.6</Subscript>(Mn<Subscript>0.9</Subscript>Co<Subscript>0.1</Subscript>)<Subscript>2</Subscript>O<Subscript>7</Subscript> single crystal

The temperature and field dependences of the magnetization, the electrical resistivity, and the magnetostriction of bilayer lanthanum manganite La_1.4Sr_1.6Mn₂O₇ single crystals and cobalt-doped La_1.4Sr_1.6(Mn_0.9Cu_0.1)₂O₇ are measured. The magnetostriction of the cobalt-doped compound increases as compared to the initial La_1.4Sr_1.6Mn₂O₇ compound, and the magnetization and the magnetoresistance of the former compound change substantially. Powder and single-crystal neutron diffraction patterns are used to detect ferromagnetic ordering in La_1.4Sr_1.6(Mn_0.9Co_0.1)₂O₇ at a temperature below T _C ~ 45(2) K, and this ordering coexists with antiferromagnetic correlations, which develop at temperatures below T _C ~ 80(5) K.     

Low-temperature structural anomalies in Pr<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>CoO<Subscript>3</Subscript>

The magnetic and crystal structures of the Pr_0.5Sr_0.5CoO₃ metallic ferromagnet have been studied by the neutron diffraction technique. It is demonstrated that below 150 K, the compound is mesoscopically separated into two crystalline phases with different spatial symmetries and with different directions of the magnetic anisotropy. The phase separation exists down to 1.5 K, and at temperatures below 90 K, the low-symmetry phase occupies about 80% of the sample volume. The main structural difference between the phases is the configuration of oxygen atoms around praseodymium and, to a certain extent, around cobalt. The ferromagnetic structure with the magnetic moment lying in the basal plane of the structure (μ_Co ≈ 1.7 μ _B at 1.5 K) arises at 234 K, whereas the component directed along the long axis of the unit cell appears at 130 K. The formation of the new structural phase and change in the orientation of the magnetic moment give rise to the anomalies of the physical and magnetic characteristics of this compound observed earlier at temperatures about 120 K.     

Current-voltage characteristics of polycrystalline (La<Subscript>0.5</Subscript>Eu<Subscript>0.5</Subscript>)<Subscript>0.7</Subscript>Pb<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> at low temperatures

The current-voltage characteristics of the polycrystalline substituted lanthanum manganite (La_0.5Eu_0.5)_0.7Pb_0.3MnO₃ have been measured at temperatures close to the metal-insulator transition temperature and at low temperatures. In both cases, the current-voltage characteristics exhibit nonlinear properties that are strongly dependent on the strength of an applied magnetic field. The mechanisms responsible for the nonlinear properties at these temperatures are found to be different: near the metal-insulator transition, the current-voltage characteristics are determined by the phase layering inside granules, while at low temperatures, they are determined by tunneling of carriers through insulating interlayers of the granules.     

Magnetic and electric properties of Eu<Subscript>0.62</Subscript>Bi<Subscript>0.38</Subscript>MnO<Subscript>3</Subscript> and Eu<Subscript>0.53</Subscript>Bi<Subscript>0.32</Subscript>Sr<Subscript>0.15</Subscript>MnO<Subscript>3</Subscript> crystals

Single crystals of Eu_0.62Bi_0.38MnO₃ and Eu_0.53Bi_0.32Sr_0.15MnO₃ solid solutions crystallizing in an orthorhombically distorted perovskite structure were prepared. At temperatures above 120 K, Eu_0.62Bi_0.38MnO₃ exhibits the properties of structural glass while remaining a dielectric at all temperatures. There is no long-range magnetic order in this compound. Eu_0.53Bi_0.32Sr_0.15MnO₃ behaves as a semiconductor above 120 K and exhibits a jump in conductivity at T = 175 K associated with a metal-insulator transition occurring within limited regions of the crystal. In these regions, there appears a ferromagnetic moment (due to double exchange mediated by charge carriers) and local electric polarization.     

Nanosecond photoelectric effects in all-oxide p-n junction of La<Subscript>0.9</Subscript>Sr<Subscript>0.1</Subscript>MnO<Subscript>3</Subscript>/SrNb<Subscript>0.01</Subscript>Ti<Subscript>0.99</Subscript>O<Subscript>3</Subscript>

Nanosecond (ns) photoelectric effects have been observed in all-oxide p-n junctions of La_0.9Sr_0.1MnO₃/SrNb_0.01Ti_0.99O₃ for the first time. The rise time was about 23 ns and the full width at half maximum was about 125 ns for the open-circuit photovoltaic pulse when the La_0.9Sr_0.1MnO₃ thin film in the p-n junction was irradiated by a laser of ≈20 ns pulse duration and 308 nm wavelength. The photovoltaic sensitivity was 80 mV/MJ for a 308 nm laser pulse.     

All-solid-state intracavity frequency-doubled Nd:Y<Subscript>0.36</Subscript>Gd<Subscript>0.64</Subscript>VO<Subscript>4</Subscript>-GdCa<Subscript>4</Subscript>O(BO<Subscript>3</Subscript>)<Subscript>3</Subscript> green laser under direct 880 nm pumping

We report a green laser at 532 nm generation by intracavity frequency doubling of a continuous wave (CW) laser operation of a 1064 nm Nd:Y_0.36Gd_0.64VO₄ laser under in-band diode pumping at 880 nm. An GdCa₄O(BO₃)₃ (GdCOB) crystal, cut for critical type I phase matching at room temperature is used for second harmonic generation of the laser. At an incident pump power of 17.8 W, as high as 2.92 W of CW output power at 532 nm is achieved. The optical-to-optical conversion efficiency is up to 16.4%, and the fluctuation of the green output power was better than 2.5% in the given 30 min.     

Synthesis and electrochemical properties of Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion battery

The layered Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ lithium-rich manganese-based solid solution cathode material has been synthesized by a simple solid-state method. The as-prepared material has a typical layered structure with R-3m and C2/m space group. The synthesized Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has an irregular shape with the size range from 200 to 500 nm, and the primary particle of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has regular sphere morphology with a diameter of 320 nm. Electrochemical performances also have been investigated. The results show that the cathode material Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ prepared at 900 °C for 12 h has a good electrochemical performance, which can deliver a high initial discharge capacity of 233.5, 214.2, 199.3, and 168.1 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. After 50 cycles, the capacity retains 178.0, 166.3, 162.1, and 155.9 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. The results indicate that the simple method has a great potential in synthesizing manganese-based cathode materials for Li-ion batteries.     

Superconductivity in Ti-doped iron-arsenide compound Sr<Subscript>4</Subscript>Cr<Subscript>0.8</Subscript>Ti<Subscript>1.2</Subscript>O<Subscript>6</Subscript>Fe<Subscript>2</Subscript>As<Subscript>2</Subscript>

Superconductivity was achieved in Ti-doped iron-arsenide compound Sr₄Cr_0.8Ti_1.2O₆Fe₂As₂ (abbreviated as Cr-FeAs-42622). The X-ray diffraction measurement shows that this material has a layered structure with the space group of P4/nmm, and with the lattice constants a = b = 3.9003 Å and c = 15.8376 Å. Clear diamagnetic signals in ac susceptibility data and zero-resistance in resistivity data were detected at about 6 K, confirming the occurrence of bulk superconductivity. Meanwhile we observed a superconducting transition in the resistive data with the onset transition temperature at 29.2 K, which may be induced by the nonuniform distribution of the Cr/Ti content in the FeAs-42622 phase.     

Structural transformations in the Al<Subscript>85</Subscript>Ni<Subscript>6.1</Subscript>Co<Subscript>2</Subscript>Gd<Subscript>6</Subscript>Si<Subscript>0.9</Subscript> amorphous alloy during multiple rolling

The effect of multiple rolling at room temperature on the structure and crystallization of the Al₈₅Ni_6.1Co₂Gd₆Si_0.9 amorphous alloy has been studied using transmission electron microscopy, differential scanning calorimetry, and X-ray diffraction. The total plastic strain is 33%. It has been shown that the deformation results in the formation of aluminum nanocrystals with the average size that does not exceed 10–15 nm. The nanocrystals are formed in regions of localization of plastic deformation. The deformation decreases the thermal effect of nanocrystallization (∼15%) as compared to the heat release at the first stage of crystallization of the unstrained sample. The morphology, structure, and distribution of precipitates have been investigated. Possible mechanisms of the formation of nanocrystals during the deformation have been discussed.     

Glass-forming ability and thermal stability of Fe<Subscript>62</Subscript>Nb<Subscript>8−x</Subscript>Zr<Subscript>x</Subscript>B<Subscript>30</Subscript> and Fe<Subscript>72</Subscript>Zr<Subscript>8</Subscript>B<Subscript>20</Subscript> amorphous alloys?

Glass-forming ability (GFA) and thermal stability of Fe₆₂Nb₈B₃₀, Fe₆₂Nb₆Zr₂B₃₀ and Fe₇₂Zr₈B₂₀ at % amorphous alloys were investigated by calorimetric (DSC and DTA) measurements. The crystallization kinetics was studied by DSC in the mode of continuous versus linear heating and it was found that both the glass transition temperature, T _g , and the crystallization peak temperature, T _p , display strong dependence on the heating rate. The partial replacement of Nb by Zr leads to lower T _g and T _x temperatures and causes a decrease of the supercooled liquid region. JMA analysis of isothermal transformation data measured between T _g and T _x suggests that the crystallization of the Fe₆₂Nb₈B₃₀ and Fe₆₂Nb₆Zr₂B₃₀ amorphous alloys take place by three-dimensional growth with constant nucleation rate. Nb enhances the precipitation of the metastable Fe₂₃B₆ phase and stabilizes it up to the third crystallization stage. Zr addition increases the lattice constant of Fe₂₃B₆ and, at the same time, decreases the grain size.