Size effects in the vibrational and electronic properties of Cu-Pb nanocomposites

Composites of Cu and Pb (immiscible in solid state) were prepared by melt spinning onto a copper disc. X-ray diffraction measurements showed the Cu-Pb composites thus obtained to consist of Pb nanoparticles of a certain size embedded in a copper matrix. The average size of the nanocrystalline Pb blocks was determined along the normals to the (111) and (200) reflecting planes, and their size distribution was measured. The vibrational, electronic, and superconducting properties of the Cu₈₅Pb₁₅ and Cu₅₀Pb₅₀ composites were derived from low-temperature heat-capacity, magnetic-susceptibility, and resistance measurements, and the contribution of Pb nanoparticles to the heat capacity was separated. The low-frequency excitation density in Pb nanocrystals was found to increase as compared to that in crystalline Pb. The observed decrease of T _c correlates with the variation of Pb nanoparticles in size, which is a consequence of the size effect in the properties of Pb nanocrystals.     

In situ investigation of morphological and phase changes during thermal annealing and oxidation of carbon-encapsulated copper nanoparticles

In situ electron microscope and X-ray investigations of the morphological and phase characteristics of copper nanoparticles encapsulated in a carbon shell were carried out. It was found that oxidation of the copper nanoparticles starts at a temperature of 200 °C. The formation of oxide phases occurs on the surface of the carbon shells, with the Cu₂O phase appearing first followed by the formation of the CuO phase. Upon heating to just below its melting point, the copper sublimes resulting in the formation of hollow carbon nanocapsules. Treatment of the initial or oxidized encapsulated copper nanoparticles with nitric acid and annealing can be used to obtain hollow carbon nanocapsules.     

Oleylamine‐Assisted Phase‐Selective Synthesis of Cu2−xS Nanocrystals and the Mechanism of Phase Control

Environmentally friendly Cu_2?x S compounds exist in many different mixed phases in nature, while their nanoscale counterparts can be pure phase with interesting localized surface plasmon resonance properties. Because of the complexity of composition and phase, controllable synthesis of Cu_2?x S nanocrystals becomes an important scientific issue in colloidal chemistry. In this work, a hot‐injection method is developed to synthesize Cu_2?x S nanocrystals by injecting a sulfur precursor into a copper precursor using oleylamine and octadecene as solvents. By varying the reaction parameters (temperature, volume ratio of oleylamine/octadecene, molar ratio of Cu/S in the precursors), hexagonal CuS, monoclinic Cu_1.75S, and rhombohedral Cu_1.8S, nanocrystals can be selectively synthesized, providing a platform to illustrate the mechanism of crystal phase control. The crystal phase control of Cu_2?x S nanocrystals is oleylamine‐determined by controlling the molar ratio of Cu/S in the reaction precursors as well as the ratio of Cu_2?x S clusters/Cu⁺ in the subsequent reaction. More importantly, temperature plays an important role in varying the molar ratio of Cu/S and Cu_2?x S clusters/Cu⁺ in the reaction system, which significantly influences the crystal phase of the resulting Cu_2?x S nanocrystals. The understanding into crystal control provides a guideline to realize reproducible phase‐selective synthesis and obtain well‐defined high‐quality materials with precise control.     

Copper and copper oxide nanoparticles in a cellulose support studied using anomalous small-angle X-ray scattering

Microcrystalline cellulose is a porous natural material which can be used both as a support for nanoparticles and as a reducer of metal ions. Cellulose supported nanoparticles can act as catalysts in many reactions. Cu, CuO, and Cu₂O particles were prepared in microcrystalline cellulose by adding a solution of copper salt to the insoluble cellulose matrix and by reducing the copper ions with several reducers. The porous nanocomposites were studied using anomalous small angle X-ray scattering (ASAXS), X-ray absorption spectroscopy, and X-ray diffraction. Reduction of Cu²⁺ with cellulose in ammonium hydrate medium yielded crystalline CuO nanoparticles and the crystallite size was about 6–20 nm irrespective of the copper concentration. The size distribution of the CuO particles was determined with ASAXS measurements and coincided with the crystallite sizes. Using sodium borohydrate or hydrazine sulfate as a reducer both metallic Cu and Cu₂O nanoparticles were obtained and the crystallite size and the oxidation state depended on the amount of reducer.     

Optimization of cuprous oxide nanocrystals deposition on multiwalled carbon nanotubes

Cu (I) phenyl acetylide was used as a source of copper to achieve a homogeneous distribution of Cu₂O nanocrystals (10–80 nm) decorated on multiwalled carbon nanotubes (MWCNTs) having an average diameter of 10 nm. Pristine MWCNTs were first oxygen-functionalized by treating them with a mixture of concentrated (H₂SO₄/HNO₃ : 3/1) acids and the products were characterized by X-ray powder diffraction, transmission and scanning electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy and thermogravimetric analysis. An easy, efficient and one-step impregnation method was followed to produce copper-containing nanoparticles on the MWCNTs. The copper-treated MWCNTs dried at room temperature were seen to be well decorated by copper-containing nanoparticles on their outer surface. The MWCNTs were then heat-treated at 400 °C in a nitrogen atmosphere to produce a homogeneous distribution of cuprous oxide nanocrystals on their surface. By varying the ratio of copper to oxygen-functionalized MWCNTs, Cu₂O nanocrystals decorated on MWCNTs with different copper content can be obtained.     

Shape evolution, photoluminescence and degradation properties of novel Cu2O micro/nanostructures

Three kinds of novel cuprous oxide (Cu₂O) micro/nanostructures are synthesized via a facile template-free hydrothermal method. Two factors are critical for the growth process of typical samples: the concentration of copper ions (Cu(II)) and the addition of Polyvinylpyrrolidone (PVP) as surfactant. It is found that the application of ethanol as solvent speeds up the reduction rate of Cu(II), and it promotes the aggregating of Cu₂O nanocrystals at the preliminary stage to form irregular spherical structures. Photoluminescence (PL) properties of the three kinds of samples and their photocatalytic activities for degradation of Methyl Orange (MO) are also measured. The sample with higher concentration of copper vacancy (V _Cu) defects has better photocatalytic ability, indicating that besides the morphology of Cu₂O nano/microcrystals, the defects in crystalline structures can also influence their electrical characteristics, and thus change their photocatalytic activity. This provides a potential method to improve the photocatalytic performances of Cu₂O crystals.     

Photoinduced growth of Cu nanoparticles on ZnO from CuCl<Subscript>2</Subscript> in methanol

Cu nanoparticles were formed on surface of nano-ZnO by UV light induced photoreduction of CuCl₂ in methanol solution suspended with ZnO nanoparticles. By controlling the reaction conditions, the average size of the produced copper nanocrystal can be fine-tuned in the range of 10–200 nm. At constant UV irradiation, the Cu nanocrystals gradually grew up as the initial concentration of copper cation was increased, showing that the in situ formed Cu nanoparticles act as a bridge to facilitate the transferring of photoexcited electrons from ZnO surface to Cu²⁺ in solution. A Redox property was also proved for the Cu nanoparticles.     

Colloidal Cu2ZnSnS4 nanocrystals generated by a facile route using ethylxanthate molecular precursors

We have demonstrated a flexible method for preparing Cu₂ZnSnS₄ (CZTS) nanocrystals by use of zinc ethylxanthate (Zn(ex)₂) and copper ethylxanthate (Cu(ex)₂). TEM, SEM, XRD, UV–vis, EDS, XPS and TG‐DTA indicate that the CZTS nanocrystals have been successfully synthesized. As air‐stable molecular precursors, Zn(ex)₂ and Cu(ex)₂ can optimize the synthesis of quaternary CZTS nanocrystals because Cu(ex)₂ and Zn(ex)₂ facilitate the formation of homogeneous precursor solutions including all precursors and then for the flexible production of CZTS nanocrystals in homogeneous reaction solutions. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A Simple Strategy to Prepare Colloidal Cu‐Doped ZnSe(S) Green Emitter Nanocrystals in Aqueous Media

A novel and simple method is described for preparing colloidal Cu‐doped ZnSe(S) quantum dots (QDs) in aqueous media by introducing copper ions using the same method as to prepare colloidal ZnSe(S). More specifically, the Cu‐doped ZnSe(S) are prepared through the nucleation‐doping method in the presence of 3‐mercaptopropionic acid as stabilizers using zinc perchlorate, copper sulphate, and NaHSe as precursors. Confirmation of the preparation of Cu‐doped ZnSe(S) nanocrystals (NCs) is done with absorption and emission spectroscopies (UV–vis and PL) as the QDs show intensive green emissions. The reduction of ions Cu²⁺ to Cu⁺ is confirmed by using electron paramagnetic resonance (EPR), in which Cu⁺ ions are silent. The size determination is performed by using transmission electron microscopy (TEM) and dynamic light scattering (DLS), resulting in Cu‐doped ZnSe(S) particles with a mean diameter of 4.6 ± 3.5 nm. The excellent stability observed for the nanoparticles overcomes the intrinsic instability of traditional aqueous Cu‐doped ZnSe(S) NCs.     

Preparation and optical properties of Cu2O hollow microsphere film and hollow nanosphere powder via a simple liquid reduction approach

In this work, we report a simple liquid reduction approach to prepare Cu₂O hollow microsphere film and hollow nanosphere powder with Cu(OH)₂ nanorods as precursor and ascorbic acid as the reductant at 60 °C. When Cu(OH)₂ nanorod array film grown on a copper foil is used as the precursor, Cu₂O thin film made up of hollow microspheres with average diameter of 1.2 μm is successfully prepared. When the Cu(OH)₂ nanorods are scraped from the copper foil and then used as the precursor, Cu₂O hollow nanosphere powder with the average diameter of 270 nm is obtained. The samples are characterized by X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and ultraviolet-vis light (UV-vis) absorption spectra. A possible formation mechanism of Cu₂O hollow spheres is discussed.     

High-performance hierarchical cypress-like CuO/Cu<Subscript>2</Subscript>O/Cu anode for lithium ion battery

Composite CuO/Cu₂O/Cu anode for lithium ion battery was designed and synthesized via facile electrodeposition and the subsequent in situ thermal oxidation in air at 300 °C for 1 h. The as-prepared composite CuO/Cu₂O/Cu anode was studied in terms of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), galvanostatic charge/discharge, cyclic voltammetry (CV), and AC impedance. As expected, the composite CuO/Cu₂O/Cu with CuO-rich surface displayed hierarchical cypress-like morphology; furthermore, the hierarchical cypress-like CuO/Cu₂O/Cu anode also delivered satisfactory electrochemical performances. For example, the reversible discharge capacity remained at 534.1 mAh/g even after 100 cycles. The enhanced electrochemical performances were attributed to the hierarchical cypress-like porous structure and the synergistic effect among the composite active copper oxides and highly conductive Cu current collector.     

Initial oxidation kinetics and energetics of Cu0.5Au0.5 (0 0 1) film investigated by in situ ultrahigh vacuum transmission electron microscopy

The initial oxidation behavior of Cu_0.5Au_0.5 (0 0 1) thin film was investigated by in situ ultrahigh vacuum transmission electron microscopy to model nano-oxidation of alloys with one active component and one noble component. The formation of irregular-shaped octahedron Cu₂O islands with cube-on-cube crystallographic orientation to the substrate film was observed at all temperature studied. The energetics of Cu₂O nucleation for Cu and Cu_0.5Au_0.5 oxidation was compared. Cu_0.5Au_0.5 oxidation has lower nucleation activation energy due to the reduced mismatch strain between Cu₂O and Cu_0.5Au_0.5 films. On the other hand, the reaction kinetics for Cu_0.5Au_0.5 alloy oxidation is slower due to the higher diffusion activation energy of Cu.     

Size-selected copper oxide nanoparticles synthesized by laser ablation

Size-tuned copper oxide nanoparticles with sizes of 9, 12, and 15 nm were fabricated by laser ablation and on-line size selection using a differential mobility analyzer at a gas pressure of 666 Pa. The dependence of the particle properties on the in situ annealing temperatures and selection sizes was investigated. The crystalline phases of the nanoparticles fabricated at temperatures below 973 K were assigned to monoclinic cupric oxide (CuO) which converted into cubic cuprous oxide (Cu₂O) when the annealing temperature was above 1,173 K. This indicates that the crystalline phases can be easily controlled by changing the annealing temperature. TEM images confirmed that well-crystallized and well-dispersed CuO and Cu₂O nanoparticles with narrow size distributions were obtained using this method. This fabrication process is useful and promising for the future investigation of the intrinsic size-dependent properties of CuO and Cu₂O.     

Influence of Cu doping on the microstructure,optical properties and photoluminescence features of Cd0.9Zn0.1S nanoparticles

Cd_0.9−xZn_0.1Cu_xS (0≤x≤0.06) nanoparticles were successfully synthesized by a conventional chemical co-precipitation method at room temperature. Crystalline phases and optical absorption of the nanoparticles have been studied by X-ray diffraction (XRD) and UV–visible spectrophotometer. XRD confirms the phase singularity of the synthesized material, which also confirmed the formation of Cd–Zn–Cu–S alloy nanocrystals rather than separate nucleation or phase formation. Elemental composition was examined by the energy dispersive X-ray analysis and the microstructure was examined by scanning electron microscope. The blue shift of absorption edge below Cu=2% is responsible for dominance of Cu⁺ while at higher Cu concentration dominated Cu²⁺, d–d transition may exist. It is suggested that the addition of third metal ion (Cu²⁺/Cu⁺) is an effective way to improve the optical property and stability of the Cd_0.9Zn_0.1S solid solutions. When Cu is introduced, stretching of Cd–Zn–Cu–S bond is shifted lower wave number side from 678 cm⁻¹ (Cu=0%) to 671 cm⁻¹ (Cu=6%) due to the presence of Cu in Cd–Zn–S lattice and also the size effect. The variation in blue band emission peak from 456 nm (∼2.72 eV) to 482 nm (∼2.58 eV) by Cu-doping is corresponding to the inter-band radiation combination of photo-generated electrons and holes. Intensity of red band emission centered at 656 nm significantly increased up to Cu=4%; beyond 4% it is decreased due to the quenching of Cu concentration.     

Chemical synthesis,characterization and evaluation of antimicrobial properties of Cu and its oxide nanoparticles

Cu nanoparticles were synthesized using low-temperature aqueous reduction method at pH 3, 5, 7, 9 and 11 in presence of ascorbic acid and polyvinylpyrrolidone. The nanoparticles were characterized using transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction techniques. Results demonstrated a strong dependence of synthesis pH on the size, shape, chemical composition and structure of Cu nanoparticles. While lower pH conditions of 3 and 5 produced Cu⁰, higher pH levels (more than 7) led to the formation of Cu₂O/CuO nanoparticles. The reducing capacity of ascorbic acid, capping efficiency of PVP and the resulting particle sizes were strongly affected by solution pH. The results of in vitro disk diffusion tests showed excellent antimicrobial activity of Cu₂O/CuO nanoparticles against a mixture of bacterial strains (Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa), indicating that the size as well as oxidation state of Cu contributes to the antibacterial efficacy. The results indicate that varying synthesis pH is a strategy to tailor the composition, structure and properties of Cu nanoparticles.     

Preparation of Cu 2 O nanoparticles dispersed in NH 2 -terminated polyethyleneoxide matrix

Small Copper (I) oxide, Cu₂O, nanoparticles dispersed in diamine-terminated polyethyleneoxide (PEO-NH₂) matrix have been successfully prepared by vacuum evaporation of copper onto the molten PEO-NH₂. The obtained composite were characterized by TEM, electron diffraction, TG-DTA and FT-IR spectroscopy. The stable composite, in which the Cu₂O nanoparticles are stabilized through interaction between NH₂ chain end groups of PEO molecules and Cu₂O nanoparticles was obtained when the samples were heat-treated at 110 ^° C. The mean size of the Cu₂O nanoparticles increased from 2.5 to 3.5 nm in diameter upon increasing the amount of initial Cu deposition. The obtained composite material having a waxy texture was soluble in many solvents without aggregation and can be handled as a simple chemical compound for starting material in various applications. Received 29 November 2000     

Synthesis of highly non-stoichiometric Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> nanoparticles with tunable bandgaps

Non-stoichiometric Cu₂ZnSnS₄ nanoparticles with average diameters of 4–15 nm and quasi-polyhedral shape were successfully synthesized by a colloidal method. We found that a non-stoichiometric composition of Zn to Cu in Cu₂ZnSnS₄ nanoparticles yielded a correlation where Zn content increased with a decrease in Cu content, suggesting formation of lattice defects relating to Cu and Zn, such as a Cu vacancy (V_Cu), antisite with Zn replacing Cu (Zn_Cu), and/or defect cluster of V_Cu and Zn_Cu. The bandgap energy of Cu₂ZnSnS₄ nanoparticles systematically varies between 1.56 and 1.83 eV depending on the composition ratios of Cu and Zn, resulting in a wider bandgap for Cu-deficient Cu₂ZnSnS₄ nanoparticles. These characteristics can be ascribed to the modification in electronic band structures due to formation of V_Cu and Zn_Cu on the analogy of ternary copper chalcogenide, chalcopyrite CuInSe₂, in which the top of the valence band shifts downward with decreasing Cu contents, because much like the structure of CuInSe₂, the top of the valence band is composed of a Cu 3d orbital in Cu₂ZnSnS₄.     

Oxidation of Zr 55 Cu 30 Al 10 Ni 5 bulk metallic glass in the glassy state and the supercooled liquid state

The oxidation behavior of Zr₅₅Cu₃₀Al₁₀Ni₅ bulk metallic glass in air in the glassy state and the supercooled liquid state was studied using a thermogravimetric analyzer, X-ray diffraction and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. It was found that the isothermal oxidation kinetics of the glass in both states follows a two-step parabolic law. The oxidation process is governed by the inward diffusion of oxygen and the outward diffusion of Cu, with the first being dominant. The faster diffusion of atoms in the supercooled liquid state led to a network precipitation of crystalline Cu, and the crystallization that occurred in this state in the later stage of oxidation caused a reduction in the rate of oxidation. Two types of Zr oxides, i.e. t-ZrO₂ and m-ZrO₂, were formed in the oxidation process in both the glassy and supercooled liquid states. t-ZrO₂ mainly formed in the outer layer of the oxide scale, while m-ZrO₂ tended to form in the inner layer. The formation of m-ZrO₂ is possibly activated by the crystallization of the glass near the interface of the oxide scale and the substrate alloy. In addition, oxidation also has a substantial effect on the formation of crystallized phases. The formation of a Cu-rich phase of Cu₁₀Zr₇ occurred in the oxidizing atmosphere. However, the formation of a Zr-rich phase of Zr₂(Ni, Cu) mainly took place in a vacuum environment. PACS 81.05.Kf; 81.65.Mq; 64.60.-i     

Electronic excitations and optical response of metal nanocomposites under heavy ion implantation

The optical transmission and ion-induced luminescence under implantation of copper ions into quartz glass (a-SiO₂) have been measured to study the processes of formation of copper nanoparticles. It is shown that in situ measurements are more informative in comparison with the ordinary approach—investigation of the properties of ion-implanted nanocomposites only after implantation. A series of experiments was performed to prove that the ion-induced luminescence band at 545–550 nm is due to Cu⁺ ions dissolved in a-SiO₂. The combined use of in situ optical techniques makes it possible to monitor the states of implanted copper (metal nanoparticles and dissolved atoms) by the change in the optical absorption near the surface plasmon resonance of nanoparticles and by the intensity of ion-induced luminescence of Cu⁺ states in solid solution. It is shown that the optical bands of defects, dissolved copper, and nanoparticles can be separated within a simple linear approximation. Near the surface plasmon resonance and defect bands, ion-induced transient optical absorption has been revealed. The transient optical absorption near the surface plasmon resonance is explained by the temperature effect. The relationship between the electronic excitation, radiation-induced optical response, and the kinetics of nanoparticle formation is analyzed. Several stages of nanoparticle formation have been established: accumulation of implanted copper in solid solution, nucleation of nanoparticles, coalescence, growth of nanoparticles, and saturation of nanocomposites.     

Optical characterization of thin thermal oxide films on copper by ellipsometry

A complete optical characterization in the visible region of thin copper oxide films has been performed by ellipsometry. Copper oxide films of various thicknesses were grown on thick copper films by low temperature thermal oxidation at 125 °C in air for different time intervals. The thickness and optical constants of the copper oxide films were determined in the visible region by ellipsometric measurements. It was found that a linear time law is valid for the oxide growth in air at 125 °C. The spectral behaviour of the optical constants and the value of the band gap in the oxide films determined by ellipsometry in this study are in agreement with the behaviour of those of Cu₂O, which have been obtained elsewhere through reflectance and transmittance methods. The band gap of copper oxide, determined from the spectral behaviour of the absorption coefficient was about 2 eV, which is the generally accepted value for Cu₂O. It was therefore concluded that the oxide composition of the surface film grown on copper is in the form of Cu₂O (cuprous oxide). It was also shown that the reflectance spectra of the copper oxide–copper structures exhibit behaviour expected from a single layer antireflection coating of Cu₂O on Cu. Received: 19 July 2001 / Accepted: 27 July 2001 / Published online: 17 October 2001