首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 109 毫秒
1.
热电阻与热电偶是常用的测温元件。测量瞬态高温时,由于传感器自身的热惯性,测量结果与真实结果之间存在很大的动态误差,减小动态误差有重要意义。文中主要分析了热电阻与热电偶温度传感器的测温原理,以及封装结构对温度传感器响应时间的影响,并建立裸露敏感元件热传导温度的数学模型,从理论上分析影响温度传感器响应时间的主要因素,并对其加以改进达到实验所需要求。  相似文献   

2.
提出了一种基于石英晶体温度频率特性的石英音叉微谐振式温度传感器。通过理论分析的方法对传感器进行设计,并采用有限元仿真对传感器的结构参数进行优化。采用光刻和蚀刻微加工技术制造石英音叉谐振器,对石英音叉温度传感器样机的频率温度特性进行实验研究。实验结果表明:石英音叉温度传感器的标准谐振频率为36.545 kHz,灵敏度为-1.9 Hz/℃,在-20到100 ℃的温度范围内,其非线性误差小于0.18%,迟滞为0.02%,与理论研究相吻合。该传感器具有高精度、高灵敏度、低功耗和低成本的特点,为高性能温度测量提供较好的解决方案。  相似文献   

3.
杨杰  刘清惓  戴伟  冒晓莉  张加宏  李敏 《物理学报》2016,65(9):94209-094209
传统百叶箱和防辐射罩内部的温度传感器受到太阳辐射会导致其温度高于大气真实温度, 升温量可达0.8 K甚至更高. 为提高大气温度观测精度, 本文设计了一种阵列式温度传感器. 利用计算流体动力学方法分析计算该传感器在不同环境条件下的辐射升温量, 采用遗传算法对计算结果进行拟合, 获得辐射升温量修正方程. 为验证阵列式温度传感器的实际性能, 研制了强制通风温度测量平台. 将阵列式温度传感器、配有传统防辐射罩的温度传感器和强制通风温度测量平台置于相同环境下, 进行大气温度观测比对实验. 配有传统防辐射罩的温度传感器辐射升温量平均值为0.409 K; 与前者相比, 阵列式温度传感器的辐射升温量仅为0.027 K. 这种阵列式温度传感器可将辐射升温引起的误差降低约93%. 辐射升温量实验测量值与修正方程修正值之间的平均偏移量为0.0174 K, 均方根误差为0.0215 K, 该结果验证了计算流体动力学方法与遗传算法的准确性. 如果配合计算流体动力学方法与遗传算法, 温度测量精度有进一步提高的潜力.  相似文献   

4.
为了提高光纤布拉格光栅(FBG)温度传感器的测温精度,提出了一种新型的光纤布拉格光栅(FBG)温度传感器的封装方法,并采用二次多项式拟合的方式标定该温度传感器。新的封装方法可以消除FBG温度传感器存在的应力交叉敏感,新的标定方式可以极大地提高光纤温度传感器的测温精度。通过对比光纤温度传感器的线性拟合和二次多项式拟合测温结果,表明这种封装方法结合二次多项式标定使得光纤温度传感器具有很好的稳定性和重复性。在0℃~80℃的温度范围内,曲线拟合度在0.9999以上,测温误差不超过0.13℃,能够满足实际工程应用的需求。  相似文献   

5.
金属比热容测量的传统方法是冷却法,用此方法通常需要手动控制秒表测量金属的降温时间从而引入较大的误差.为了克服该方法的弊端,采用外设温度传感器通过蓝牙连接智能手机,实时采集金属的降温曲线,实现对降温时间的精确测量.该方法不仅避免了人工控制秒表测量时间的误差,同时还能得到温度随时间下降的连续曲线,方便调入Origin软件对数据进行拟合和计算.实验研究表明:该实验结果与标准值符合得很好.  相似文献   

6.
运载火箭作机动飞行时,陀螺和加速度计输出中引入的与机动状态相关的动态误差项会严重影响冗余捷联惯组故障诊断的效果,增大误警率。本文研究验证了利用卡尔曼滤波估计动态误差以补偿等价向量的方法,滤波补偿能够减弱由于运载火箭机动引起的动态误差项,利用补偿后的等价向量成功检测到未补偿时难以检测的故障。同时也发现了陀螺的补偿效果不如加速度计补偿效果好的现象。深入研究后发现,试验陀螺的随机误差偏大,掩盖了动态误差。得到了当传感器的随机误差项是动态误差项的5倍以上时可不进行误差补偿的有用结论。  相似文献   

7.
针对温度传感器测量误差受温度影响比较大,必须使用温度补偿的方法对测温数据值进行修正。本文介绍了一种温度补偿的方法:主要采用oringin软件利用最小二乘法拟合实验数据的方式,进行系统误差分析处理后再对温度传感器进行温度精确标定,可以有效消除传感器非线性误差。对AD590传感器温度精确标定后实测电压与温度线性关系良好,证实此方法可以很好的修正温度对AD590传感器测量误差的影响,系统测量精度可达±0.02℃。将此实验的温度标定后的AD590传感器直接应用到其它实验中加深学生对温度传感器具体应用的理解。  相似文献   

8.
对采用热电偶测量导热系数的实验进行改进,利用DISLab温度传感器测金属盘达到平衡的温度和散热盘的温度,解决了传统的导热系数测定时误差较大的问题。实验表明,该实验操作简单,精度高,具有明显的优势。  相似文献   

9.
李玮瑶  王启明  吕海莲 《应用声学》2014,22(10):3111-31133125
针对传统的无人机温度检测系统对于无人机机箱温度异变信号的检测实时性和准确较低的问题,设计并实现了基于DS18B20温度传感器关联模型的无人机机箱温度异变信号检测系统,根据温度在不同位置的测量值不同,建立不同位置的关联模型,利用温度传感器之间的关联系数λ,判断不同位置的温度信号是否正常,并对温度异变信号发出警报;硬件设计主要包括温度传感器检测电路、数据处理模块、声光报警模块等;软件设计主要包括工作流程、DS18B20实时温度传感器关联性的程序实现等;最后对无人机100次的飞行提取机箱检测温度进行试验实验,通过温度传感器DS18B20对无人机机箱实际的温度数据进行检测,结果表明:机箱内部模块周围温度变化与散热风扇周围的温度平均温度变化相差在0.5℃以内,在误差允许范围内,相关性很大;另外,与传统系统对比可知,该系统的检测准确率高达95%以上,且稳定性强,能为无人机的安全飞行提供了可靠保障。  相似文献   

10.
提出了一种基于石英晶体温度频率特性的石英音叉微谐振式温度传感器。通过理论分析的方法对传感器进行设计,并采用有限元仿真对传感器的结构参数进行优化。采用光刻和蚀刻微加工技术制造石英音叉谐振器,对石英音叉温度传感器样机的频率温度特性进行实验研究。实验结果表明:石英音叉温度传感器的标准谐振频率为36.545kHz,灵敏度为-1.9Hz/℃,在-20到100℃的温度范围内,其非线性误差小于0.18%,迟滞为0.02%,与理论研究相吻合。该传感器具有高精度、高灵敏度、低功耗和低成本的特点,为高性能温度测量提供较好的解决方案。  相似文献   

11.
电热法测固体比热容实验的改进   总被引:2,自引:0,他引:2  
探讨了电热法测固体的比热容实验装置的改进,并介绍用自补偿方式消除系统误差的方法,用集成温度传感器AD590测量温度,通过模拟电路调零和放大,其温度由数字毫伏表直接显示,用不锈钢真空杜瓦瓶代替量热器。  相似文献   

12.
Two techniques for the integration of temperature sensors in microchannels have been developed and compared. The two designs rely on different measuring principles, the first deriving from integrated circuit silicon microfabrication and the second being based on conventional commercial sensors. The proposed experimental approach offers a broad flexibility of applications, overcoming the material limitations typical of microelectronic integrated sensors. Heat transfer of gases in microchannels was studied to validate and characterize the integrated sensor systems, and the results were also compared with computational fluid dynamics (CFD) simulations. Whereas conventional sensors result as a simpler and robust technology, integrated circuit-based sensors offer higher sensitivities and potentials.  相似文献   

13.
水的比汽化热测量装置的改进   总被引:1,自引:1,他引:0  
对传统的测量水的比汽化热实验中的加热和输气装置进行改进,采用集成电路温度传感器测量量热器中温度,实现了水比汽化热非电量电测,较准确地测量水的比汽化热.  相似文献   

14.
电热法测液体比热容实验的改进   总被引:2,自引:0,他引:2  
分析了电热法测液体比热容实验中误差的主要来源,介绍了一种适用于量热器系统,无论在密闭还是开放条件下,测量液体比热容的新方法。  相似文献   

15.
非轴向力下埋入式光纤传感器应变传递分析   总被引:2,自引:0,他引:2  
李宏男  周广东  任亮 《光学学报》2007,27(5):87-793
利用剪滞法建立了当光纤光栅传感器的轴线和基体主应力的方向成一定角度时,光纤光栅传感器的测量应变与基体结构实际应变之间的关系,进而得出了光纤光栅传感器的平均应变传递率的一般公式。采用裸光纤光栅传感器进行实验,在倾斜角度α为30.72°时,实验所得的波长变化之比分别为:0.727,0.738,0.746;理论计算所得的波长变化之比为0.739,相对误差都在2%以内。同时分析了埋设角度偏差对测量结果的影响。研究结果表明,非轴向力作用下光纤光栅传感器的应变与结构基体应变之间的传递关系与其在轴向力作用下存在明显的区别,埋设角度的偏差会给测量结果造成一定的误差。  相似文献   

16.
对用力敏传感器测量液体表面张力系数仪器进行研究,重新设计了吊环,便于吊环的水平调节,对待侧液体表面均匀下降的方法和实验装置做了重新设计,减小了实验误差,同时增加了待测液体的变温控制,能够精确测量液体表面张力系数与温度的关系,扩充了实验内容.  相似文献   

17.
Willatzen M 《Ultrasonics》2003,41(2):105-114
Ultrasonic flowmeter performance is addressed for the case of cylindrically shaped flowmeters employing two reciprocal ultrasonic transducers A and B so as to measure time-of-flight differences between signals transmitted from transducer A towards B followed by an equivalent signal transmitted from transducer B towards A. In the case where a liquid flows through the flowmeter's measuring section ("spoolpiece"), the arrival times of the two signals differ by an amount related to the flow passing between the two transducers. Firstly, a detailed study of flow measurement errors with mean flow in the laminar flow regime is carried out as a function of the mode index and the transducer diameter/cylinder diameter ratio in the case where no temperature gradients are present in the flowmeter sensor. It is shown that all modes except the fundamental mode overestimate the mean flow by a factor of 33.33% while excitation of the fundamental mode solely give error-free measurements. The immediate consequences are that the flowmeter error decreases as the transducer diameter/cylinder diameter ratio approaches 1 from 0 reflecting the fact that the excitation level of the fundamental mode increases from almost 0 to 1 as this ratio approaches 1 from 0. Secondly, the effect on flowmeter performance due to flow-induced temperature gradients is examined. It is shown that the presence of temperature gradients leads to flowmeter errors at the higher-flow values even in the case where the fundamental mode is the only mode excited. It is also deduced that flowmeter errors in general depend on the distance between transducers A and B whether temperature gradients exist or not. This conclusion is not reflected in the usual definition of flowmeter errors given by the so-called mode-dependent deviation of measurement introduced in earlier works.  相似文献   

18.
研制了混合法测固体比热容的仪器. 该仪器将加热部分与测温部分巧妙的合为一体,并设计了将物体从高温快速过渡到低温的装置,从而减小了热损失,同时温度测量采用了AD590温度传感器的装置,进一步减小了实验中的系统误差.  相似文献   

19.
In this work we present an experimental technique for the estimation of the average temperature on the cutting edge of each insert in a milling tool. The experimental device used thermistors, one per insert, and a rotational collector in order to ensure the transmission of the signals between the rotating tool and the acquisition device. Each thermistor is located at a point in the tool close to the tip of each insert. The average temperature on the cutting edge of each insert is estimated from the temperature at the nearest sensor and a model expressing these two temperatures. This model is achieved from the noninteger system identification method.  相似文献   

20.
Abstract

This article aims to employ a two-dimensional inverse heat conduction technique in designing an experiment for accurately estimating the local convective heat transfer coefficient in slot jet impingement, given temperature measurements at some interior locations in the target plate. The method uses a sequential procedure together with the Beck function specification approach. Solution accuracy and experimental errors are examined using simulated temperature data. It is concluded that a good estimation of the space variable heat transfer coefficient can be made from the knowledge of the transient temperature recordings. The technique is used in a series of numerical experiments to provide the optimum experimental design for a slot jet impingement heat transfer investigation.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号