溶剂对辐射变色膜吸收剂量的影响

本实验室分别选用无水乙醇和丙酮溶液为溶剂制成两种类型的辐射变色膜, 并对这两种辐射变色膜进行了60Co γ射线与紫外线辐照, 研究不同溶剂对辐射变色膜吸收剂量的影响。实验发现, 60Co γ射线与紫外线辐照后, 使用丙酮作溶剂的辐射变色膜变色效果比无水乙醇的更加明显。在相同的辐照剂量下, 使用丙酮作为溶剂的变色膜比用无水乙醇的光谱吸收峰(680 nm)值平均高65.5%。γ射线辐照时, 用丙酮作为溶剂的辐射变色膜变色的辐照剂量下限为0.5 Gy, 而用无水乙醇做为溶剂的为1 Gy; 紫外辐照时, 用丙酮为溶剂的辐射变色膜吸收峰处吸收剂量的线性响应区间为0～6×100 μJ/cm2, 而用无水乙醇做为溶剂的为0～36×100 μJ/cm2。     

变色薄膜的紫外线辐照响应研究

 制备了含多芳氨基甲烷类化合物的高分子变色薄膜，经紫外线辐照后，这种薄膜随吸收剂量的不同由无色透明逐渐变为绿色，在可见光区主要吸收峰位于626 nm附近，光密度响应与辐照时间近似成线性关系。研究表明：该辐射变色薄膜变色响应随紫外线能量密度增加而增加；分次辐照能略微提高光密度响应；辐射变色薄膜响应受温度和湿度影响较大，在20～50 ℃温度范围、40%～60%相对湿度范围，响应基本稳定；卤代物添加剂可以大大提高辐射变色薄膜的响应灵敏度；受后辐照效应影响，辐照结束最初2 h内响应迅速增加，2 h后响应才基本稳定。     

辐射变色薄膜的质子辐照响应

 用J-2.5质子静电加速器提供的质子束,对研制的一种高灵敏度新型辐射变色膜进行质子辐射响应研究。该变色膜以聚乙烯醇缩聚物为基质,以类丁二炔化合物为有机染色材料,质子能量为2.0 MeV,辐照注量为1.0×10¹⁰～1.0×10¹² cm^-2。用光谱响应测试薄膜的辐射效应显示：变色薄膜颜色由粉红渐变为蓝色, 并随着辐照剂量的增加而逐渐加深;用图像分析仪分析辐照后靶材的光密度发现,图像的光密度随聚焦斑距离的增大而减小;用分光光度计测试其吸收光谱发现,主吸收峰值出现在660 nm附近,且吸收峰处的响应吸光度与质子注量具有较好的线性关系;对新型变色薄膜辐照后持续效应的研究表明,变色膜辐照后续效应微弱,辐照后可以立即测量,且对测量环境变化不敏感。     

高感度辐射变色薄膜电子剂量计

 以聚乙烯醇缩聚物为基质,以类丁二炔化合物为有机染色材料,研制了一种高灵敏度新型辐射变色膜。采用JJ-2型范格拉夫静电加速器对变色薄膜进行剂量范围为15～90 Gy的电子束辐照,结果显示:变色薄膜颜色由粉红渐变为蓝色,并随着辐照剂量的增加而逐渐加深;分光光度计测试其吸收光谱,发现主吸收峰值出现在675 nm附近,且吸收峰处的响应吸光度与电子注量具有较好的线性关系;对变色层厚度为20～80 μm的变色膜,吸收峰处的响应吸光度与其变色层厚度也成线性关系;添加不同比例的协同剂,能提高变色薄膜的响应灵敏度;变色膜辐照后续效应微弱,辐照后可以立即测量,且对测量环境变化不敏感。     

锆英石的抗γ射线辐照能力和Rietveld结构精修

为研究放射性核素固化介质备选矿物锆英石的抗γ射线辐照结构稳定性,以澳大利亚锆英石为研究对象,通过⁶⁰Co源γ射线辐照装置对样品施以1728 kGy的γ射线辐照.利用X射线荧光光谱仪、扫描电子显微镜和X射线衍射仪对样品的元素含量、γ射线辐照前后的微观形貌及物相变化进行表征,同时利用Rietveld方法对γ射线辐照前后的样品进行了结构精修.结果表明:澳大利亚锆英石经1728 kGy剂量的γ射线辐照后未发生物相变化,射线辐照前后样品的晶胞参数仅发生了10^-4 量级的变 关键词： 锆英石 γ射线 辐照 Rietveld结构精修     

聚丙烯/抗老化剂复合体系的γ-射线辐照降解研究

研究了聚丙烯(PP)及含有受阻酚类抗氧剂和受阻胺类光稳定剂复合体系的PP复合物经过γ-射线辐照后发生的结构变化及抗老化剂所起作用。实验利用红外光谱(FTIR)和示差扫描量热法(DSC)对PP的结构变化进行了系统表征。研究结果表明,当辐照剂量较小(50 kGy)时,纯PP及其复合物体系均未发生明显降解;当辐照剂量较大(≥50 kGy)时,PP及其复合物的羰基指数迅速提高,二者的结晶温度和熔融温度大幅度降低,说明PP发生了严重降解。在相同γ-射线辐照剂量条件下(≥50 kGy),PP复合物的羰基指数高于纯PP,而结晶温度以及熔融温度低于纯PP,表明高辐照剂量下抗老化剂复合物的存在不但没有阻止聚丙烯的降解,反而加快了降解的速率。     

新型辐射变色凝胶的紫外辐照研究

将类丁二炔化合物自组装成纳米囊泡后,均匀分散于凝胶载体中,研制出一种新型的辐射变色凝胶剂量计。用电镜观测了囊泡形貌,采用CL-1000型紫外交联仪对凝胶进行辐照,测试并研究了凝胶对紫外辐照的变色响应、辐射后效应、扩散效应等剂量学性能。结果表明:该辐射变色凝胶在5~150mJ/cm2能量密度范围内对紫外线辐照具有良好的响应线性,同时克服了扩散效应、辐射后效应、成型能力差等现有凝胶剂量计的不足。该辐射变色凝胶剂量计适于光学扫描方式测量剂量分布。     

利用X射线衍射技术分析黄藤材微纤丝角、结晶度及γ射线的影响

为了解棕榈藤材基本材性、提高我国棕榈藤资源高附加值加工利用水平,以我国特有的黄藤为研究对象,应用X射线衍射法测定黄藤材微纤丝角、结晶度,并就γ射线辐照处理对微纤丝角、结晶度有何影响进行了分析。结果表明:纤维微纤丝角在33.4°～38.7°范围内,平均为36.1°;藤皮处微纤丝角不比藤芯处的大。当标准剂量率为2.5×103Gy.h-1、辐射剂量分别为3,9和15kGy三个水平时,辐照处理前后对应微纤丝角分别为36.2°和35.8°,35.9°和35.4°,36.2°和35.4°,较处理前分别减小了1.10%,1.39%和2.21%。纤维素结晶度在24.8%～32.0%范围内,平均为28.6%,藤皮处结晶度均比藤芯处高。辐照处理前后对应结晶度分别为28.1%和26.0%,28.1%和26.9%,28.5%和27.1%,较处理前分别减小了7.58%,4.34%和4.70%,其中当辐射剂量为3kGy时,辐照导致结晶度差异在0.001水平上极显著。     

傅里叶变换红外光谱法研究核辐照对三七总皂苷粉成分的影响

采用傅里叶变换红外光谱(卷积谱)法对经不同剂量y-射线核辐照的三七总皂苷粉进行了对比研究.辐照剂量不高于9kGy时,三七总皂苷粉样品的化学成分几乎没有发生变化;三七总皂苷粉样品经15kGy及以上的辐照剂量辐照后,可能产生新的化学成分;经21kGy的剂量辐照,三七总皂苷粉产生了人参、三七粉所含的普通成分(非三七总皂苷成分...     

同步辐射（软X射线,紫外）辐照农作物的生物效应研究

同步辐射的紫外辐照萌动麦种子的辐射敏感性为：大麦大于冬麦，大麦大于春麦。在３．５－２２ｈｅＶＸ射线辐照干麦种子的两次重复实验中，其辐射敏感性的次序发生了变化；０．６－３ｋｅＶ超软Ｘ射线辐照干麦种子时，当代幼苗出现了４０－９０％的“条状叶绿素缺失”的变异，这在其他射线辐照中未曾见过，是首次发现的生物效应。     

Leuco crystal violet/poly(vinyl butyral) thin film as a high-dose dosimeter

A polyvinyl butyral film incorporating a radiochromic leuco crystal violet dye (LCV) and a UV-absorber of tinuvin-P has been investigated as a high-dose dosimetry for ⁶⁰Co radiation processing in the dose range of 1–100 kGy. Upon γ-ray exposure, the prepared film undergoes visual color change to deep purple color characterized with an absorption band peaking at 594 nm with a shoulder around 552 nm. The response of films stored in dark place at room temperature overall a period of 55 days exhibited good stability, that the increase in response of irradiated and unirradiated films did not exceed 2% and 4%, respectively overall this storage period. The results indicate that no further protection of films from laboratory fluorescent light during the measurement of irradiated film is required. The effect of temperature and relative humidity on the performance of film during irradiation and the overall uncertainty associated with absorbed dose monitoring were investigated in the present study.     

碳离子束混合LET辐照的EBT3辐射变色胶片剂量修正方法

针对EBT3辐射变色胶片对碳离子束混合LET辐照的剂量欠响应比较了两种剂量修正方法。利用260 MeV/u的碳离子束通过被动降能得到多种剂量平均LET的碳离子束,利用这些碳离子束进行了胶片剂量响应刻度辐照,选择最佳的拟合公式得到了胶片剂量刻度曲线。使用RE(Relative Efficiency)量化了EBT3胶片随LET的剂量欠响应,并使用RE剂量修正法修正了混合LET辐照胶片的剂量。此外,根据剂量刻度曲线公式中拟合参数随不同LET所占剂量比例的变化规律,提出了拟合参数剂量修正法并修正了混合LET辐照胶片的剂量。最后比较了这两种方法的结果,表明拟合参数方法得到的剂量偏差在5%以内,优于RE方法10%以内的剂量偏差。     

用傅立叶变换红外光谱法研究核辐照对人参粉成分的影响

本文采用傅立叶变换红外光谱(吸收光谱、二阶导数谱及差谱)法对经不同剂量核辐照的人参粉进行了对比研究.辐照剂量不高于9 kGy时,人参粉样品的化学成分几乎没有发生变化;人参粉样品经15kGy及以上的辐照剂量辐照后,可能产生新的化学成分,表明采用辐照剂量不高于9 kGy的核辐照杀灭人参粉污染的微生物和各种寄生虫卵是可行的;...     

Characterization and optimization of EBT2 radiochromic films dosimetry system for precise measurements of output factors in small fields used in radiotherapy

The accurate determination of absorbed dose in small photon beams, especially for stereotactic radiation therapy, is a difficult task with commercially available detectors. As these small fields are characterized by high dose gradients, a lack of lateral particle equilibrium and a variation of energy spectra with beam sizes, a dosimeter with high resolution, tissue-equivalence and high precision is required. The new radiochromic film EBT2, which meets these criteria, was fully characterized in Institut de Radioprotection et Sûreté Nucléaire (IRSN) for this application. This type of film was tested with the reading system EPSON Dual Lens Perfection V700 flatbed scanner in transmission mode. Warm-up effects of the scanner were studied as well as the influence of the scanner light. Uniformity of unirradiated and irradiated EBT2 films in terms of pixel value was found to be respectively 0.3% (1 SD) and 0.5% (1 SD). An original, accurate and efficient radiochromic film dosimetry protocol was established. The overall uncertainty for dose measurement with EBT2 films using this protocol was estimated at less than 2% (1 SD). Encouraging measurements of output factors were performed on a Novalis system.     

Gafchromic HD-V2 investigations using MeV ion beams in vacuum

ABSTRACT

Gafchromic HD-V2 films are employed to study the response to light ions useful in radiotherapy, such as protons, helium and carbon beams. The effects induced by the ions at an energy within about 300 keV and 16?MeV were investigated in terms of optical absorbance measurements in the irradiated active region of the film. The employed ion doses range between 0.4 Gy and 12?kGy. The results show that the net optical density increases almost exponentially with the absorbed dose and that it becomes saturated after prolonged dose higher than 1?kGy. The optical density produced in the film was measured by light transmission measurements at 700?nm wavelength, at which is observed the highest gafchromic sensitivity. Calibration curves of optical density versus exposure dose and type of ion are given. The dependence on the ion stopping power was presented and discussed.     

电子辐照改性PAN/PEO基体凝胶电解质对染料敏化太阳电池性能的提高

采用电子束（EB）对聚丙烯腈/聚氧化乙烯（PAN/PEO）凝胶电解质进行了剂量为13～260 kGy的辐照, 并对辐照改性的电解质组装的染料敏化太阳电池(DSSC)进行了性能测量。 结果表明, 改性后的DSSC的光电转化效率比改性前的高; 并且随EB辐照剂量的增加, DSSC效率先迅速增加(0～65 kGy), 然后缓慢减小(65～130 kGy)直至趋于一个平衡值(130～260 kGy)。 提升DSSC效率的最佳辐照剂量为65 kGy, 此时效率提高了约36%。 对比DSSC短路电流、 开路电压和填充因子随辐照剂量的变化, 发现DSSC效率的提高主要是由短路电流的提高引起的。 测量表明, 辐照改性后的DSSC时间稳定性得到了改善, 并且辐照剂量越高, 稳定性的改善越明显。 In this work, PAN/PEO (polyacrylonitrile/polyethylene oxide) based gel electrolyte was irradiated by electron beam (EB) with dose from 13 to 260 kGy. Then, DSSC (dye sensitized solar cell) was fabricated by the irradiated electrolyte and characterized. The results show that the efficiency of the DSSC fabricated by irradiated electrolyte is promoted comparing with DSSC fabricated by un irradiated electrolyte. And with irradiation dose increasing, the DSSC efficiency increases rapidly at first (0～65 kGy), then, drops down slowly (65～130 kGy), finally trends to a stable value (130～260 kGy). It indicates that there is an optimal irradiation dose, at which the promotion of DSSC efficiency is the highest, approximate 36%. Observed from the change of short circuit current, open circuit voltage and fill factor, short circuit current promotion by EB irradiation is found to be the main reason of DSSC performance promotion. The time stability measurement of the DSSC indicates that EB irradiation on PAN/PEO electrolyte reduces the loss of efficiency and the limiting effects become more apparent as the irradiation dose increases.     

A radiochromic film based on leucomalachite green for high-dose dosimetry applications

A colorless polyvinyl butyral film (PVB) based on radiation-sensitive dye of leucomalachite green (LMG) was investigated as a high-dose dosimeter for gamma radiation processing applications in the dose range of 3–150 kGy. The useful applications for such dose range are food irradiation treatment, medical devices sterilization and polymer modification. Gamma irradiation of the film induces a significant intensity of green color, which can be characterized by a main absorption band at 627 nm and a small band at 425 nm. The variation in response of irradiated film stored in the dark and under laboratory light illumination was less than 3% during the first 6 days of storage. The response of film during irradiation was slightly influenced by relative humidity in the range of 12–76%; however, it was significantly affected by temperature in the range of 5–40 °C. The radiation chemical yield was reported to be 6.76 × 10⁻⁶ mol/J at the absorbed dose of 30 kGy for the film containing 6.5% of LMG dye. The overall uncertainty associated with routine dose monitoring would be less than 6% at a 95% confidence level if the dosimeter was being corrected for irradiation conditions and being calibrated with reference standard dosimeter in the production facility.