Fabrication of Zr and Zr-N surface alloying layers and hardness improvement of Ti-6Al-4V alloy by plasma surface alloying technique

Titanium alloys are very attractive materials because they have high specific strength, excellent corrosion and erosion resistance in many active environments. However, their low hardness values and poor tribological properties require improvement of their surface properties. The present study is concerned with the fabrication of Zr and Zr-N alloying layers in the surfaces of Ti-6Al-4V substrates by plasma surface alloying technique. The microstructure, chemical composition and hardness of the surface alloying layers were analyzed to understand the mechanisms of surface alloying and hardness improvement. The Zr and Zr-N surface alloying layers formed were homogeneous and compact, in which the surface alloying elements all displayed gradient distributions. The Zr and Zr-N surface alloying layers all enhanced the surface hardness of Ti-6Al-4V alloy. Zr-N surface alloying resulted in greater improvement in hardness and the maximum microhardness of (1.37 ± 0.04) × 10³ HK was obtained at the subsurface, which was much higher than that of the untreated Ti-6Al-4V alloy. The Zr-N surface alloying layer consisted of an outer nitride layer and an inner diffusion zone of Zr and N, and its very high hardness owed to the formation of the nitride layer. The mechanism of hardness improvement of Zr surface alloyed Ti-6Al-4V alloy was solid solution strengthening.     

A study on wear resistance and microcrack of the Ti3Al/TiAl + TiC ceramic layer deposited by laser cladding on Ti-6Al-4V alloy

Laser cladding of the Al + TiC alloy powder on Ti-6Al-4V alloy can form the Ti₃Al/TiAl + TiC ceramic layer. In this study, TiC particle-dispersed Ti₃Al/TiAl matrix ceramic layer on the Ti-6Al-4V alloy by laser cladding has been researched by means of X-ray diffraction, scanning electron microscope, electron probe micro-analyzer, energy dispersive spectrometer. The main difference from the earlier reports is that Ti₃Al/TiAl has been chosen as the matrix of the composite coating. The wear resistance of the Al + 30 wt.% TiC and the Al + 40 wt.% TiC cladding layer was approximately 2 times greater than that of the Ti-6Al-4V substrate due to the reinforcement of the Ti₃Al/TiAl + TiC hard phases. However, when the TiC mass percent was above 40 wt.%, the thermal stress value was greater than the materials yield strength limit in the ceramic layer, the microcrack was present and its wear resistance decreased.     

The effect of thermal aging on the strength and the thermoelectric power of the Ti-6Al-4V alloy

When the Ti-6Al-4V alloy is overaged at 500-600°C, nanometer-sized α₂ (Ti₃Al) particles can be homogeneously precipitated inside a phases, thereby leading to strength improvement. Widmanstätten and equiaxed microstructures containing fine α₂ (Ti₃Al) particles were obtained by overaging the Ti-6Al-4V alloy. Precipitation of α₂ (Ti₃Al) particles was monitored using thermoelectric power measurements for different aging conditions in the Ti-6Al-4V alloy. Overaging heat treatments were conducted at 515, 545 and 575°C for different aging times. In addition, overaging samples were examined by optical microscopy, scanning electron microscopy and hardness measurements. It was found that the thermoelectric power is very sensitive to the aging process in the two studied Ti-6Al-4V structures.     

Combining wire and coaxial powder feeding in laser direct metal deposition for rapid prototyping

Powder and wire deposition have been used separately in many laser-cladding, rapid prototyping and other additive manufacturing applications. In this paper, a new approach is investigated by simultaneously feeding powder from a coaxial nozzle and wire from an off-axis nozzle into the deposition melt pool. Multilayer parts are built from 316L steel using a 1.5 kW diode laser and different configurations of the powder and wire nozzles are compared in terms of surface roughness, deposition rate, porosity and microstructure. The parts are analysed using scanning electron microscopy (SEM), X-ray diffraction (XRD) and optical microscopy techniques. Results show that deposition efficiency increased and surface roughness decreased with the combined process; some porosity was present in samples produced by this method, but it was 20-30% less than in samples produced by powder alone. Wire injection angles into the melt pool in both horizontal and vertical planes were found to be significant for attaining high deposition efficiency and good surface quality. Reasons for the final sample characteristics and differences between the combined process and the separate powder and wire feeding techniques are discussed.     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

Combination of laser keyhole and conduction welding: Dissimilar laser welding of niobium and Ti-6Al-4V

Pulsed Nd:YAG laser welding of pure niobium plate to titanium alloy Ti-6Al-4V sheet in butt joint is studied regarding the laser/metal interaction modes. To obtain the optimized process parameters in dissimilar welding of Ti-6Al-4V/Nb, the melting ratio of laser beam energy for each weld counterpart is evaluated experimentally. Different laser welding modes of keyhole and conduction are predicted regarding the absorbed energy from the similar laser pulses on each weld counterpart. Laser keyhole and conduction welding were observed simultaneously through direct visualization of laser interaction with dissimilar metals using High Speed Imaging (HSI) system.     

Effect of solution temperature and cooling rate on microstructure and mechanical properties of laser solid forming Ti-6Al-4V alloy

The effect of solution temperature and cooling rate on microstructure and mechanical properties of laser solid forming (LSF) Ti-6Al-4V alloy is investigated.The samples are solutions treated at 900,950,and 1000°C,followed by water quenching,air cooling,and furnace cooling,respectively.It is found that the cooling rate of solution treatment has a more important effect on the microstructure in comparison with the solution temperature.The martensite α'formed during water quenching results in the higher hardnes...     

Microstructure and osteoblast response of gradient bioceramic coating on titanium alloy fabricated by laser cladding

To construct a bioactive interface between metal implant and the surrounding bone tissue, the gradient calcium phosphate bioceramic coating on titanium alloy (Ti-6Al-4V) was designed and fabricated by laser cladding. The results demonstrated that the gradient bioceramic coating was metallurgically bonded to the titanium alloy substrate. The appearance of hydroxyapatite and β-tricalcium phosphate indicated that the bioactive phases were synthesized on the surface of coating. The microhardness gradually decreased from the coating to substrate, which could help stress relaxation between coating and bone tissue. Furthermore, the methyl thiazolyl tetrazolium (MTT) assay of cell proliferation revealed that the laser-cladded bioceramic coating had more favorable osteoblast response compared with the surface of untreated titanium alloy substrate.     

Hydrogen peroxide treatment on Ti-6Al-4V alloy: A promising surface modification technique for orthopaedic application

Ti-6Al-4V alloy was treated with various concentrations (5 wt.%, 15 wt.% and 25 wt.%) of hydrogen peroxide (H₂O₂) and then heat treated to produce an anatase titania layer. The surface modified substrates were immersed in simulated body fluid (SBF) solution for the growth of an apatite layer on the surface and the formed apatite layer was characterized using various surface characterization techniques. The results revealed that titania layer with anatase nature was observed for all H₂O₂ treated Ti-6Al-4V alloy, irrespective of the H₂O₂ concentrations. Ti-6Al-4V alloy treated with 15 wt.% and 25 wt.% of H₂O₂ induced apatite formation, however 5 wt.% of H₂O₂ treated Ti-6Al-4V failed to form apatite layer on the surface. The electrochemical behaviour of H₂O₂ treated specimens in SBF solution was studied using potentiodynamic polarization and electrochemical impedance spectroscopy. Ti-6Al-4V alloy treated with 25 wt.% of H₂O₂ solution exhibited low current density and high charge transfer resistance values compared to specimens treated with other concentrations of H₂O₂ and untreated Ti-6Al-4V alloy.     

Single-step laser deposition of functionally graded coating by dual ‘wire-powder’ or ‘powder-powder’ feeding—A comparative study

The creation of iron-copper (Fe-Cu) alloys has practical application in improving the surface heat conduction and corrosion resistance of, for example, conformal cooling channels in steel moulds, but is difficult to achieve because the elements have got low inter-solubility and are prone to solidification cracking. Previous work by these authors has reported a method to produce a graded iron-nickel-copper coating in a single-step by direct diode laser deposition (DLD) of nickel wire and copper powder as a combined feedstock. This work investigates whether dual powder feeds can be used in that process to afford greater geometric flexibility and compares attributes of the ‘nickel wire and copper powder’ and ‘nickel powder and copper powder’ processes for deposition on a H13 tool steel substrate.In wire-powder deposition, a higher temperature developed in the melt pool causing a clad with a smooth gradient structure. The nickel powder in powder-powder deposition did not impart much heat into the melt pool so the melt pool solidified with sharp composition boundaries due to single metal melting in some parts. In wire-powder experiments, a graded structure was obtained by varying the flow rates of wire and powder. However, a graded structure was not realised in powder-powder experiments by varying either the feed or the directions. Reasons for the differences and flow patterns in the melt pools and their effect on final part properties of parts produced are discussed.     

Hydrogen storage in sonicated carbon materials

The hydrogen storage in purified single-wall carbon nanotubes (SWNTs), graphite and diamond powder was investigated at room temperature and ambient pressure. The samples were sonicated in 5 M HNO₃ for various periods of time using an ultrasonic probe of the alloy Ti-6Al-4V. The goal of this treatment was to open the carbon nanotubes. The maximum value of overall hydrogen storage was found to be 1.5 wt %, as determined by thermal desorption spectroscopy. The storage capacity increases with sonication time. The sonication treatment introduces particles of the Ti alloy into the samples, as shown by X-ray diffraction, transmission electron microscopy, and chemical analysis. All of the hydrogen uptake can be explained by the assumption that the hydrogen is only stored in the Ti-alloy particles. The presence of Ti-alloy particles does not allow the determination of whether a small amount of hydrogen possibly is stored in the SWNTs themselves, and the fraction of nanotubes opened by the sonication treatment is unknown. Received: 18 December 2000 / Accepted: 18 December 2000 / Published online: 9 February 2001     

Features of the plasma saturation of nanocrystalline and coarse-crystalline titanium samples with hydrogen and deuterium

We investigate the laws governing the saturation of nano- and coarse-crystalline Ti-6Al-4V alloy samples with hydrogen from high-frequency and glow discharge plasmas with a view to finding materials suitable for making hydrogen accumulators. We conclude that nanocrystalline Ti-6Al-4V alloy holds promise for creating hydrogen accumulators, and hydrogen plasma of high-frequency discharge origin is a cleaner hydrogen saturation medium than that of non-self-sustained discharge origin.     

Combined laser/sol-gel synthesis of calcium silicate coating on Ti-6Al-4V substrates for improved cell integration

New studies have shown that tricalcium silicate powder is a bioactive material and can encourage bone-implant integration. This paper reports the synthesis of Ca₂SiO₄ coating on Ti-6Al-4V samples by laser irradiation under submerged conditions. The results of using a 160-1500 LDL 1.5 kW diode laser (rectangular spot = 2.5 mm × 3.5 mm, λ = 808 and 940 nm with equal intensities) is reported. A number of experiments were carried out varying laser parameters, such as scanning speed and laser power. Coatings are evaluated in terms of microstructure, elemental composition (XRD), SEM and wettability. The in vitro biocompatibility of the samples is investigated by monitoring 2T3 osteoblast cell growth on the samples.     

Optimization of weld bead geometry in laser welding with filler wire process using Taguchi’s approach

In the present work, laser welding with filler wire was successfully applied to joining a new-type Al–Mg alloy. Welding parameters of laser power, welding speed and wire feed rate were carefully selected with the objective of producing a weld joint with the minimum weld bead width and the fusion zone area. Taguchi approach was used as a statistical design of experimental technique for optimizing the selected welding parameters. From the experimental results, it is found that the effect of welding parameters on the welding quality decreased in the order of welding speed, wire feed rate, and laser power. The optimal combination of welding parameters is the laser power of 2.4 kW, welding speed of 3 m/min and the wire feed rate of 2 m/min. Verification experiments have also been conducted to validate the optimized parameters.     

Laser processing of bulk Al–12Si alloy: influence of microstructure on thermal properties

The feasibility of enhancing the thermal conductivity of an alloy via microstructural refinement was examined using Al–12%Si alloy as a model material. Al–12Si alloy samples were fabricated at different process parameters using laser engineered net shaping (LENS?) and the effect of microstructural features on the thermal conductivity was studied and compared with conventionally cast alloy. The large difference in melting points and laser light absorptivities of Si and Al as well as the low melt viscosity of Al–12Si alloy resulted in a very small process window to successfully fabricate bulk Al–12Si alloy samples using LENS?. Comparison of microstructural features of laser-processed samples with cast Al–12Si alloy showed significant refinement in eutectic Si for laser processed samples. Microstructural refinement not only improved the thermal conductivity of Al–12Si alloy but also compensated the detrimental effect of porosity on thermal conductivity. The thermal conductivity of cast alloy varied between 82 and 93?W/mK, which is ～21–76% lower than the values exhibited by laser-processed samples in the range 103–153?W/mK. The results of LENS? fabrication, microstructural evolution and thermal properties of Al–12Si alloy bulk structures can be extended to other immiscible alloys and metal matrix composites for a variety of engineering applications.     

Assessment of precipitates of aged Ti-6Al-4V alloy by ultrasonic attenuation

Abstract

Ti-6Al-4V alloy with different microstructures was investigated by means of ultrasonic attenuation measurements. Widmanstätten and equiaxed microstructures were obtaining by heat treating a Ti-6Al-4V alloy. These two microstructures were over-aged at 545 °C at different ageing times. In order to find out the factors affecting the variation in the ultrasonic attenuation, the heat-treated samples were examined by optical microscopy and scanning electron microscopy. Based on the theory of ultrasonic attenuation in a solid media, the mechanisms of ultrasonic attenuation in the Ti-6Al-4V alloy with different microstructures were analysed. It was found that in both cases with Widmanstätten and equiaxed microstructures, the ultrasonic attenuation increased with frequency. After ageing, the ultrasonic attenuation was mainly attributed to the scattering loss which included the stochastic and the Rayleigh scattering due to the precipitation of Ti₃Al particles homogeneously distributed in the α phase. Data analysis presented in the study showed that ultrasonic attenuation yields more accurate area fractions of precipitates predictions when a polynomial fit is performed.     

Laser surface remelting of plasma sprayed nanostructured Al2O3-13wt%TiO2 coatings on titanium alloy

Plasma sprayed nanostructured coatings were successfully fabricated on a titanium alloy (Ti-6Al-4V) substrate using the as-prepared nanostructured Al₂O₃-13wt%TiO₂ feedstock. A CO₂ laser was used to remelt the plasma sprayed coatings. The effects of laser remelting on the phase constituents, microstructure and properties of the ceramic coatings were investigated. The laser remelted coatings (LRmC) possessed a much denser and more homogenous structure and excellent metallurgical bonding to the substrate. The average porosity of the LRmC was reduced to 0.9%, compared with 6.2% of the as-sprayed coatings. The net-like structure in the as-prepared feedstock remained in the coatings before and after laser remelting. The metastable γ-Al₂O₃ phase in the as-sprayed coatings transformed to stable α-Al₂O₃ during laser remelting. The LRmC could remain nanostructure. The microhardness of the coatings was enhanced to 1000-1400 HV_0.3 after laser remelting, which was much higher than that of the plasma sprayed coatings and 2-3 times higher that of the substrate. Significant decreases in surface roughness were also found in the LRmC.     

Superplastic Deformation of Titanium Alloy with Different Structure and Phase Composition

Russian Physics Journal - The α+β titanium alloy Ti-6Al-4V having different structure and phase composition is investigated in this paper under the tensile deformation in the temperature...     

XPS study of porous dental implants fabricated by electro-discharge-sintering of spherical Ti-6Al-4V powders in a vacuum atmosphere

A single electro-discharge-sintering (EDS) pulse (0.7-2.0 kJ/0.7 g), from a 300 μF capacitor, was applied to atomized spherical Ti-6Al-4V powder in a vacuum to produce a porous-surfaced implant compact. A solid core surrounded by a porous layer was formed by a discharge in the middle of the compact. X-ray photoelectron spectroscopy was used to study the surface characteristics of the implant material. C, O, and Ti were the main constituents, with smaller amounts of Al, V, and N. The implant surface was lightly oxidized and was primarily in the form of TiO₂ with a small amount of metallic Ti. A lightly etched EDS implant sample showed the surface form of metallic Ti, indicating that EDS breaks down the oxide film of the as-received Ti-6Al-4V powder during the discharge process. The EDS Ti-6Al-4V implant surface also contained small amounts of aluminum oxide in addition to TiO₂. However, V detected in the EDS Ti-6Al-4V implant surface did not contribute to the formation of the oxide film. The small amount of N in the implant surface resulted from nitride material that was also found in the as-received Ti-6Al-4V powders.     

光纤激光气体氮化钛合金发射光谱及等离子体研究

激光气体氮化工艺可在钛合金表面快速生成氮化层,提高钛合金表面硬度和耐磨性,促进钛合金应用.采用光纤激光气体氮化Ti-6Al-4V合金,为了明确氮化过程光谱发射区是否形成等离子体,采用探针法检测了光谱发射区导电性;为了研究工艺参数对光谱特性、光谱发射区温度及等离子数量的影响,采用光谱仪采集了氮化过程发射光谱,并采用高速摄...