Thermal properties of continuously spun carbon nanotube fibres

As indicated by theory and experimental measurements individual carbon nanotubes (CNTs) have very high values of thermal conductivity. One of the challenges is to achieve high thermal conductivity in macroscopic assemblies of CNTs such as fibres, films and composites, paving the way to a wide range of applications. CNT fibres have tremendous potential in succeeding as the future materials for a variety of applications when properties at the nanoscale are translated to their macroscopic assemblies. In this paper we report the measurements of thermal conductivity of continuously spun CNT fibres and its dependence on temperature. Thermal conductivity measurements were performed using in-house built temperature sensing microscope probe. Specific thermal conductivity of CNT fibres showed an order of magnitude advantage over the traditional materials used for heat dissipation.     

The effect of particle size on the thermal conductivity of alumina nanofluids

We present new data for the thermal conductivity enhancement in seven nanofluids containing 8–282 nm diameter alumina nanoparticles in water or ethylene glycol. Our results show that the thermal conductivity enhancement in these nanofluids decreases as the particle size decreases below about 50 nm. This finding is consistent with a decrease in the thermal conductivity of alumina nanoparticles with decreasing particle size, which can be attributed to phonon scattering at the solid–liquid interface. The limiting value of the enhancement for nanofluids containing large particles is greater than that predicted by the Maxwell equation, but is predicted well by the volume fraction weighted geometric mean of the bulk thermal conductivities of the solid and liquid. This observation was used to develop a simple relationship for the thermal conductivity of alumina nanofluids in both water and ethylene glycol.     

Effect of Nanoparticles on Thermal Properties Enhancement in Different Oils – A Review

The development of stable dispersion of nanoparticles in different oils is gaining momentum for close circuit applications as most of the mineral oils used are not very good thermal conductors. The enhancement of thermal conductivity with optimum enhancement of viscosity of oil with nanoparticles poses a serious challenge for use of such fluids in cooling. Transformer oil, mineral oil, silicon oil, hydrocarbon fuels, biodiesel, and some organic solutions have been used as the base fluids for studying the effect of nanoparticles for improving thermal efficiency. Innovative heat transfer fluids are produced by suspending metallic or nonmetallic nanometer-sized solid particles. Although a large number of sources are available on water-based nanofluids, the number of such reports on oil-based nanofluids is rather limited. The aim of this article is to summarize recent developments on the preparation methods of nanofluids based on oil, its stability, thermal conductivity enhancement, nanoparticle effect on viscosity, heat transfer characteristics, breakdown voltage, dielectric properties, and applications of such nanofluids.     

Study of ionic solvent-free carbon nanotube nanofluids and its composites with epoxy matrix

A facile way to synthesis ionic solvent-free multi-walled carbon nanotubes (CNTs) (MWNTs) nanofluids has been introduced. Fourier transform infrared spectra and transmission electron microscope (TEM) were employed to study the surface structure of MWNTs in the nanofluids. The thermal property of the nanofluids was characterized by thermogravimetric analysis and differential scanning calorimetry. The stability of the nanofluids in the deionized water was obtained through UV–Vis absorption spectrum. Rotary rheometer was used to test the flow feature of the nanofluids. The results of conductivity indicate that the seepage threshold value of solvent-free nanofluids in water is about 0.408 vol.% (volume fraction). Meanwhile, it is found that the ionic nanofluids dispersed well in epoxy matrix. The mechanical properties, such as bend modulus, strength and impact toughness have been improved at the same time. TEM images can tell the great dispersion of solvent-free CNTs nanofluids in the epoxy matrix. It means that this kind of nanofluids will be excellent nanofiller in the nanocomposites.     

Influence of the particle size distribution on the thermal conductivity of nanofluids

In a previous study, we have obtained an equation to predict the thermal conductivity of nanofluids containing nanoparticles with conductive interface. The model is maximal particle packing dependent. In this study, the maximal packing is obtained as a function of the particle size distribution, which is the Gamma distribution. The thermal conductivity enhancement depends on the averaged particle size. Discussion concerning the influence of the suspension pH on the particle packing is made. The proposed model is evaluated using number of sets from the published experimental data to the thermal conductivity enhancement for different nanofluids.     

A thermal conductivity model for nanofluids including effect of the temperature-dependent interfacial layer

The interfacial layer of nanoparticles has been recently shown to have an effect on the thermal conductivity of nanofluids. There is, however, still no thermal conductivity model that includes the effects of temperature and nanoparticle size variations on the thickness and consequently on the thermal conductivity of the interfacial layer. In the present work, the stationary model developed by Leong et al. (J Nanopart Res 8:245–254, 2006) is initially modified to include the thermal dispersion effect due to the Brownian motion of nanoparticles. This model is called the ‘Leong et al.’s dynamic model’. However, the Leong et al.’s dynamic model over-predicts the thermal conductivity of nanofluids in the case of the flowing fluid. This suggests that the enhancement in the thermal conductivity of the flowing nanofluids due to the increase in temperature does not come from the thermal dispersion effect. It is more likely that the enhancement in heat transfer of the flowing nanofluids comes from the temperature-dependent interfacial layer effect. Therefore, the Leong et al.’s stationary model is again modified to include the effect of temperature variation on the thermal conductivity of the interfacial layer for different sizes of nanoparticles. This present model is then evaluated and compared with the other thermal conductivity models for the turbulent convective heat transfer in nanofluids along a uniformly heated tube. The results show that the present model is more general than the other models in the sense that it can predict both the temperature and the volume fraction dependence of the thermal conductivity of nanofluids for both non-flowing and flowing fluids. Also, it is found to be more accurate than the other models due to the inclusion of the effect of the temperature-dependent interfacial layer. In conclusion, the present model can accurately predict the changes in thermal conductivity of nanofluids due to the changes in volume fraction and temperature for various nanoparticle sizes.     

Comments on the effect of liquid layering on the thermal conductivity of nanofluids

This article provides critical examinations of two mathematical models that have been developed in recent years to describe the impact of nano-layering on the enhancement of the effective thermal conductivity of nanofluids. Discrepancy between the two models is found to be an artefact of an incorrect derivation used in one of the models. With correct formulation, both models predict effective thermal conductivity enhancements that are not significantly greater than those predicted by classical Maxwell theory. This study indicates that nano-layering by itself is unable to account for the effective thermal conductivity enhancements observed in nanofluids.     

Investigation on characteristics of thermal conductivity enhancement of nanofluids

It has been shown that a nanofluid consisting of nanoparticles dispersed in base fluid has much higher effective thermal conductivity than pure fluid. In this study, four kinds of nanofluids such as multiwalled carbon nanotube (MWCNT) in water, CuO in water, SiO₂ in water, and CuO in ethylene glycol, are produced. Their thermal conductivities are measured by a transient hot-wire method. The thermal conductivity enhancement of water-based MWCNT nanofluid is increased up to 11.3% at a volume fraction of 0.01. The measured thermal conductivities of MWCNT nanofluids are higher than those calculated with Hamilton–Crosser model due to neglecting solid–liquid interaction at the interface. The results show that the thermal conductivity enhancement of nanofluids depends on the thermal conductivities of both particles and the base fluid.     

Model for heat conduction in nanofluids

A comprehensive model has been proposed to account for the large enhancement of thermal conductivity in nanofluids and its strong temperature dependence, which the classical Maxwellian theory has been unable to explain. The dependence of thermal conductivity on particle size, concentration, and temperature has been taken care of simultaneously in our treatment. While the geometrical effect of an increase in surface area with a decrease in particle size, rationalized using a stationary particle model, accounts for the conductivity enhancement, a moving particle model developed from the Stokes-Einstein formula explains the temperature effect. Predictions from the combined model agree with the experimentally observed values of conductivity enhancement of nanofluids.     

Investigation of Laminar Convective Heat Transfer of a Novel Tio2–Carbon Nanotube Hybrid Water-Based Nanofluid

The current study was conducted to investigate the convective heat transfer coefficient of a novel TiO₂–CNT hybrid nanofluid through the shell-and-tube heat exchanger under a laminar flow and the effects of temperature and mass fraction on it. TiO₂–CNT hybrid nanofluids were prepared using a new and modified hydrolysis technique. The thermal conductivity of the TiO₂–CNT hybrid nanofluid and other thermo-physical properties were assessed. Results indicate that the effective thermal conductivity and heat transfer coefficient of the base fluid was influenced significantly and increased by the 0.2 wt% of this novel hybrid nanofluid in distilled water.     

Overview of Hybrid Nanofluids Development and Benefits

Conventional fluids have poor heat transfer properties, but their vast applications in power generation, chemical processes, heating and cooling processes, electronics and other microsized applications make the reprocessing of those thermofluids to have better heat transfer properties quite essential. Recently, it has been shown that the addition of solid nanoparticles to various fluids can increase the thermal conductivity and can influence the viscosity of the suspensions by tens of percent. Thermophysical properties of nanofluids were shown dependent on the particle material, shape, size, concentration, the type of the base fluid, and other additives. In spite of some inconsistency in the reported results and insufficient understanding of the mechanism of the heat transfer in nanofluids, it has been emerged as a promising heat transfer fluid. In the continuation of nanofluids research, the researchers have also tried to use hybrid nanofluid recently, which is engineered by suspending dissimilar nanoparticles either in mixture or composite form. The idea of using hybrid nanofluids is to further improve the heat transfer and pressure drop characteristics by trade-off between advantages and disadvantages of individual suspension, attributed to good aspect ratio, better thermal network and synergistic effect of nanomaterials. As a conclusion, the hybrid nanofluids containing composite nanoparticles yield significant enhancement of thermal conductivity. However, the long-term stability, production process, selection of suitable nanomaterials combination to get synergistic effect and cost of nanofluids may be major challenges behind the practical applications.     

Theory for anisotropic thermal conductivity of magnetic nanofluids

Effective thermal conductivity tensor for magnetic nanofluids containing magnetizable nanoparticles suspended in a base liquid is theoretically investigated with a two-step homogenization method. First, we adopt differential effective medium theory to determine the equivalent thermal conductivity of magnetizable nanoparticle chains. Second, we generalize self-consistent anisotropic effective medium theory to study the effective thermal conductivity tensors of magnetic nanofluids. Numerical results show that the aspect ratio of chain-like aggregated clusters plays an important role in enhancement of anisotropic thermal conductivity. In addition, our theoretical results on the elements of thermal conductivity parallel to the fields Kez and perpendicular to the fields Kex are in good agreement with experimental data. Furthermore, we predict the nonmonotonic dependence of effective thermal conductivity on magnetic field strength, in accordance with experimental reports.     

Analytical prediction of forced convective heat transfer of fluids embedded with nanostructured materials (nanofluids)

Nanofluids are a new class of heat transfer fluids developed by suspending nanosized solid particles in liquids. Larger thermal conductivity of solid particles compared to the base fluid such as water, ethylene glycol, engine oil etc. significantly enhances their thermal properties. Several phenomenological models have been proposed to explain the anomalous heat transfer enhancement in nanofluids. This paper presents a systematic literature survey to exploit the characteristics of nanofluids, viz., thermal conductivity, specific heat and other thermal properties. An empirical correlation for the thermal conductivity of Al₂O₃ + water and Cu + water nanofluids, considering the effects of temperature, volume fraction and size of the nanoparticle is developed and presented. A correlation for the evaluation of Nusselt number is also developed and presented and compared in graphical form. This enhanced thermophysical and heat transfer characteristics make fluids embedded with nanomaterials as excellent candidates for future applications.      

Investigation of thermal conductivity and rheological properties of vegetable oil based hybrid nanofluids containing Cu–Zn hybrid nanoparticles

Vegetable oils (Ground nut) are being investigated to serve as a possible substitute for non-biodegradable mineral oils, which are currently being used as metal-cutting fluids in machining processes. In this study, thermophysical properties of hybrid nanofluids (vegetable oil) to be used as metalworking cutting fluids are investigated. In-situ synthesis of copper (Cu) and zinc (Zn) combined hybrid particles is performed by mechanical alloying with compositions of 50:50, 75:25, and 25:75 by weight. Characterizations of the synthesized powder were carried out using X-ray diffraction, a particle size analyzer, FE-SEM, and TEM. Hybrid nanofluids with all the three combinations of hybrid nanoparticles were prepared by dispersing them into a base fluid (vegetable oil). The thermophysical properties, such as thermal conductivity and viscosity, were studied for various volume concentrations and at a range of temperatures. Experimental results have shown enhancement in thermal conductivity in all cases and also an increase in viscosity. The enhancement in viscosity is similar in all three combinations, as the particle size and shape are almost identical. The enhancement in thermal conductivity is higher in Cu–Zn (50:50), resulting in better enhancement in thermal conductivity due to the Brownian motion of the particles and higher thermal conductivity of the nanoparticles incorporated.     

On the thermal expansion of CNT/Cu composites for electronic packaging applications

Carbon nanotubes (CNTs) exhibit both excellent high thermal conductivity and low coefficient of thermal expansion (CTE), which are an ideal reinforcement in composite materials for high performance electronic packaging applications. In the present study, CNT/Cu composites containing CNTs varying from 0 vol.% to 15 vol.% are prepared, and their CTE behavior is studied in detail. The results indicate that the CTE of 0–10 vol.% CNT/Cu composites is significantly decreased with increasing CNT content. However, as the CNT content increases to 15 vol.%, the decrease in CTE of the composites is pronouncedly reduced. Possible mechanisms are discussed in combination with CTE model predictions.     

Investigation of thermal transport in colloidal silica dispersions (nanofluids)

Thermal conductivity enhancement in colloidal silica dispersions (nanofluids) is investigated experimentally using a novel optical technique. The effects of nanoparticle size, concentration, and state of aggregation are examined. New data on well dispersed systems are compared to published data obtained using the more conventional transient hot-wire technique and good agreement was found. Experimental results are also compared with model predictions for relative thermal conductivity based on effective medium theory. For systems composed of larger diameter nanoparticles (~30 nm), good agreement was found between the measured thermal conductivity enhancement and that predicted by the classical Maxwell-Garnett model. For systems composed of smaller nanoparticles (∼10 and 20 nm), thermal conductivity enhancement was reduced by as much as 10%, presumably because interfacial thermal resistance effects become important. Measurements on two systems that were induced to form gels exhibited an increase in thermal conductivity of approximately 5% relative to the well-dispersed systems. The observed increase in thermal conductivity is larger than that predicted by a recently proposed model for aggregated nanofluids.     

Enhanced field emission characteristics of zinc oxide mixed carbon nano-tubes films

A composite material of Zinc oxide and carbon nano-tubes (ZnO-CNTs) paste was synthesized by mixing multi-wall CNTs, ZnO nano-grains and organic vehicles. The microstructures and the morphologies of screen-printed films were characterized by field-emission scanning electron microscope. Results show that ZnO flakes geometrically matched with CNTs by filling into the interspaces of CNTs or directly covering upon CNTs. The field emission characteristics of films are found to be greatly effected by ZnO nano-grains. Especially, the turn-on electric field of ZnO-CNT film (1.17 V/μm) which is far lower than that of usual CNT films (1.70 V/μm). Furthermore, except that better emission stability is achieved, brightness and emission uniformity are notably enhanced as well. It can be speculated that the special microstructures of ZnO mixed CNT films dominate the enhanced electrical conductivity, thermal conductivity, and effective emitters.     

Fabrication, characterization and measurement of thermal conductivity of Fe3O4 nanofluids

Magnetite Fe₃O₄ nanoparticles were synthesized by a co-precipitation method at different pH values. The products were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and transmission electronic microscopy. Their magnetic properties were evaluated on a vibrating sample magnetometer. The results show that the shape of the particles is cubic and they are superparamagnetic at room temperature. Magnetic nanofluids were prepared by dispersing the Fe₃O₄ nanoparticles in water as a base fluid in the presence of tetramethyl ammonium hydroxide as a dispersant. The thermal conductivity of the nanofluids was measured as a function of volume fraction and temperature. The results show that the thermal conductivity ratio of the nanofluids increases with increase in temperature and volume fraction. The highest enhancement of thermal conductivity was 11.5% in the nanofluid of 3 vol% of nanoparticles at 40 °C. The experimental results were also compared with the theoretical models.     

碳纳米流体强化传热研究

在去离子水中分别添加了单壁、多壁碳纳米管材料,通过配比一定质量的亲水性分散剂,经超声波振荡试制了水基碳纳米流体。测试分析了不同碳纳米管材料质量分数下的纳米流体热导率和动力粘度等重要热物性参数。测试结果表明:碳纳米管粒子能够强化基液工质导热性能,随着其质量分数的增加,水基单壁、多壁碳纳米流体热导率均明显提高;单壁碳纳米流体粘度显著增加,多壁碳纳米流体粘度无明显变化,多壁碳管更适用于纳米流体强化传热。     

Novel Cu–Cr alloy matrix CNT composites with enhanced thermal conductivity

Carbon nanotubes (CNTs) are incorporated into the Cu–Cr matrix to fabricate bulk CNT/Cu–Cr composites by means of a powder metallurgy method, and their thermal conductivity behavior is investigated. It is found that the formation of Cr₃C₂ interfacial layer improves the interfacial bonding between CNTs and Cu–Cr matrix, producing a reduction of interfacial thermal resistance, and subsequently enhancing the thermal conductivity of the composites. The thermal conductivity of the composites increases by 12 % and 17 % with addition of 5 vol.% and 10 vol.% CNTs, respectively. The experimental results are also theoretically analyzed using an effective medium approximation (EMA) model, and it is found that the EMA model combined with a Debye model can provide a satisfactory agreement to the experimental data.