Q-switched pulse generation from an all-fiber distributed Bragg reflector laser using graphene as saturable absorber

A Q-switched distributed Bragg reflector fiber laser using a graphene passive saturable absorber is proposed in a cavity consisting of a fiber Bragg grating and Faraday rotator mirror as end mirrors, together with a highly doped erbium-doped fiber as a gain source. The laser has a Q-switched threshold of about 28 mW and a tunable repetition rate of 10.4-18.0 kHz with varying pump power. The shortest pulse width obtained from the system is 3.7 its, with a maximum pulse energy and peak power of 22.2 nJ and 3.4 mW, respectively.     

Synchronization and Coherent Combining of Two Pulsed Fiber Ring Lasers Based on Direct Phase Modulation

We demonstrate a scalable architecture for coherent combining of pulsed fiber ring lasers based on mutual injection and direct phase modulation. By direct phase modulation in the common arm of two ring lasers, synchronous pulsed lasers can be generated and coherent combining of the two synchronous lasers is obtained. Two pulsed fiber ring lasers are coherently combined with 0.55μJ pulse energy and 10 μs pulse duration at a repetition rate of 27.5 kHz. Experimental results show that the two fiber ring lasers are phase locked with an invariable phase difference of π and have good temporal synchronization and spatial coherence. The combining efficiency of the two pulsed fiber laser reaches 90% and the fringe contrast is larger than 40%. Neither active phase control nor polarization control is used in our experiment and this method can be extended to combine more beams and higher repetition rate scaling up to higher power.     

Dark pulse emission in nonlinear polarization rotation-based multiwavelength mode-locked erbium-doped fiber laser

We experimentally show dark pulse generation in all-normal dispersion multiwavelength erbium-doped fiber laser（EDFL） with a long cavity of figure-of-eight configuration. The EDFL generates a stable multiwavelength laser with 0.47 nm spacing at 24 m W threshold pump power, while the number of lines obtained increases with the pump power. A dark pulse emission is observed as the pump power is increased above 137 m W, with fundamental repetition rate of 29 k Hz and pulse width of 2.7 μs. It is observed that the dark pulse train can be shifted to second-, third-, and fourth-order harmonic dark pulses by carefully adjusting the polarization controller. For the fundamental dark pulse, the maximum pulse energy of 32.4 n J is obtained at pump power of 146.0 mW.     

Nonlinear polarization rotation-induced pulse shaping in a stretched-pulse ytterbium-doped fiber laser

We report on controllable pulse shaping in a Yb-doped stretched-pulse fiber laser followed by a high-power chirped pulse amplifier. We demonstrate that the pulses after an extra-cavity grating pair change their intensity profile from Lorentz to Gaussian and then to sech2 shapes by adjusting the intra-cavity polarization through a quarter-wave plate inside the fiber laser cavity. The laser pulses with different pulse shapes exhibit pulse-to-pulse amplitude fluctuation of -- 1.02%, while the sech2-shaped pulse train is provided with a more stable free-running repetition rate as a result of the stronger self-phase modulation in the fiber laser cavity than Lorentz- and Gaussian-shaped pulse trains.     

Q-switched Er-doped fiber laser with low pumping threshold using graphene saturable absorber

We propose a Q-switched Er-doped fiber laser(EDFL) with a threshold pumping power as low as 7.4 mW, and demonstrate using graphene polyvinyl alcohol(PVA) thin film as a passive saturable absorber(SA). The SA is fabricated from graphene flakes, which is synthesized by electrochemical exfoliation of graphite at room temperature in 1% sodium dodecyl sulfate aqueous solution. The flakes are mixed with PVA solution to produce a thin film, which is then sandwiched between two ferrules to form a SA and integrated in the EDFL ring cavity to generate a stable Q-switched pulse train. The pulse train operates at 1560 nm with a threshold pump power of 7.4 mW. At maximum 1480 nm pump power of 33.0 mW, the EDFL generates an optical pulse train with a repetition rate of 27.0 kHz and pulse width of 3.56 μs. The maximum pulse energy of 39.4 nJ is obtained at a pump power of 14.9 mW. This laser can be used as a simple and low-cost light source for metrology, environmental sensing, and biomedical diagnostics.     

325 MHz and near transform-limited pulse output directly from an Er：fiber ring laser

A compact Er:fiber ring laser operated at a fundamental repetition rate of 325 MHz is reported.Two gain fibers with opposite dispersion are employed to shorten the fiber laser cavity for high repetition rate and soliton-like pulse generation without losing gain and compactness.The spectral bandwidth of the output pulse is 24 nm and the direct pulse duration is 123 fs without extra-cavity compression,which are values near the transform-limited range.     

Dual-wavelength fiber grating laser in linear overlapping cavity

We report a switchable dual-wavelength fiber grating laser in linear overlapping cavity. The laser features two overlapping cavities sharing a single Yb-doped gain medium fiber and two sets of fiber Bragg gratings. A coiling fiber setup is inserted into the 1035 nm laser cavity. Given that the bending loss is inversely related to the bending radius, the cavity loss of 1035-nm can be modulated. Modulating the bending loss facilitates the switching of the fiber grating laser to a single-or dual-wavelength output at 1030 or 1035 nm and convenient tuning of the power ratio of the two wavelengths. An approximately 152.6-mW output power and up to 38-dB polarization extinction ratio are observed. The simultaneous lasing at I030 and 1035 nm is a qualified seeder source for amplification to high power scale and can be applied to difference frequency generation of a terahertz signal. This dual-wavelength fiber grating laser is a potential pump source for generating terahertz radiation using a novel approach.     

Q-Switched Raman Fiber Laser with Molybdenum Disulfide-Based Passive Saturable Absorber

We demonstrate a Q-switched Raman fiber laser using molybdenum disulfide(MoS_2) as a saturable absorber(SA).The SA is assembled by depositing a mechanically exfoliated MoS_2 onto a fiber ferrule facet before it is matched with another clean ferrule via a connector.It is inserted in a Raman fiber laser cavity with a total cavity length of about 8 km to generate a Q-switching pulse train operating at 1560.2 nm.A 7.7-km-long dispersion compensating fiber with 584 ps·nm~(-1)km~(-1) of dispersion is used as a nonlinear gain medium.As the pump power is increased from 395 mW to 422 mW,the repetition rate of the Q-switching pulses can be increased from 132.7 to137.4kHz while the pulse width is concurrently decreased from 3.35μs to 3.03μs.The maximum pulse energy of 54.3nJ is obtained at the maximum pump power of 422 mW.These results show that the mechanically exfoliated MoS_2 SA has a great potential to be used for puise generation in Raman fiber laser systems.     

Eye-safe,single-frequency pulsed all-fiber laser for Doppler wind lidar

A single-frequency pulsed erbium-doped fiber(EDF) laser with master-oscillator power-amplifier configuration at 1 533 nm is developed. A short-cavity,erbium-doped phosphate glass fiber laser is utilized as a seeder laser with a linewidth of 5 kHz and power of 40 mW. The seeder laser is modulated to be a pulse laser with a repetition rate of 10 kHz and pulse duration of 500 ns. The amplifier consists of two pre-amplifiers and one main amplifier. The detailed characteristics of the spectrum and linewidth of the amplifiers are presented. A pulse energy of 116 μJ and a linewidth of 1.1 MHz are obtained. This laser can be a candidate transmitter for an all-fiber Doppler wind lidar in the boundary layer.     

Simulation of nanosecond square pulse fiber laser based on nonlinear amplifying loop mirror

A nanosecond square pulse fiber laser based on the nonlinear amplifying loop mirror(NALM) is numeri-cally analyzed by the nonlinear Schrdinger equation. The fiber cavity with a NALM has a tendency to provide pulse shaping effect with nonlinearity increasing in the NALM,and the nanosecond square pulse is generated by the pulse shaping effect. The numerical results show that the stable square pulse can be obtained when the parameters of the NALM are chosen appropriately. The generated square pulses have flat top and no internal structure.     

Generation of dual-wavelength domain-wall rectangular-shape pulses in HNLF-based fiber ring laser

The generation of dual-wavelength domain-wall rectangular-shape pulses in a highly nonlinear fiber (HNLF)-based fiber ring laser is experimentally demonstrated. The dual-wavelength lasing operation is realized by employing the intracavity birefringence-induced spectral filtering effect. An 85 m long HNLF is introduced into the fiber ring laser to enhance the nonlinear effect, which is favorable for the cross coupling between the two lasing beams. Experimentally, it was found that the interval of two domain walls in the time domain could be adjusted by simply tuning the linear cavity phase delay, which results in the achievement of different output pulse shapes. By properly rotating the polarization controller (PC), the dual-wavelength rectangular-shape pulses could be efficiently obtained. The proposed fiber laser provides a simple and efficient way to generate rectangular-shape pulse.     

Fourier domain mode locking pulse fiber laser

A novel pulse fiber laser is proposed based on the modulation of the lasing wavelength. Different from conventional amplitude or phase modulated mode-locking fiber lasers, the proposed fiber laser is with a so-called Fourier domain mode locking (FDML) operation (i.e., the cavity round-trip time of the optical pulse should match the period that the open time window of the tunable filter appears for the lasing wavelength or its harmonics). An FDML pulse fiber laser with a cavity round-trip frequency of 19.46 kHz is demonstrated and optical pulses with repetition rate of 19.46 kHz are achieved when the wavelength modulation frequency is 9.73 kHz.     

Modulation instability induced by cross-phase modulation in a dual-wavelength dispersion-managed soliton fiber ring laser

We report on the observation of the modulation instability induced by cross-phase modulation in a dual-wavelength operation dispersion-managed soliton fiber ring laser with net negative cavity dispersion. The passively mode-locked operation is achieved by using a nonlinear polarization rotation technique. A new type of dual-wavelength operation, where one is femtosecond pulse and the other is picosecond pulse operation, is obtained by properly rotating the polarization controllers. When the dual-wavelength pulses are simultaneously circulating in the laser ring cavity, a series of stable modulation sidebands appears in the picosecond pulse spectrum at longer wavelength with lower peak power due to modulation instability induced by cross-phase modulation between the two lasing wavelengths. Moreover, the intensities and wavelength shifts of the modulation sidebands can be tuned by varying the power of the femtosecond pulse or the lasing central wavelengths of the dual-wavelength pulses. The theoretical analysis of the modulation instability induced by cross-phase modulation in our fiber laser is also presented.     

LD端面抽运Nd:YAG 1319nm/1338nm双波长激光器研究

从LD端面抽运固体激光器的激光阈值公式出发，建立了双波长激光同时振荡的阈值条件，理论计算了腔镜对于两个波长的透过率关系，实现了LD端面抽运Nd:YAG 1319nm/1338nm双波长激光连续和准连续输出.双波长激光连续输出功率可达6W，斜效率为30%；准连续输出功率在重复频率50kHz时可达4.75W，斜效率为24.73%，脉冲宽度为55.05ns；腔内插入布儒斯特片，在重复频率为50kHz时，双波长激光准连续线偏振输出功率可达2.22W，不稳定性小于0.52%，M²     

LD端面抽运Nd:YAG 1319/1338nm双波长激光器研究

从LD端面抽运固体激光器的激光阈值公式出发,建立了双波长激光同时振荡的阈值条件,理论计算了腔镜对于两个波长的透过率关系,实现了LD端面抽运Nd:YAG 1319nm/1338nm双波长激光连续和准连续输出.双波长激光连续输出功率可达6W,斜效率为30%;准连续输出功率在重复频率50kHz时可达4.75W,斜效率为24.73%,脉冲宽度为55.05ns;腔内插入布儒斯特片,在重复频率为50kHz时,双波长激光准连续线偏振输出功率可达2.22W,不稳定性小于0.52%,M² 关键词： 端泵Nd:YAG激光器 1319nm/1338nm双波长 声光调Q 太赫兹波     

Tunable and switchable dual-wavelength passively mode-locked fiber ring laser with high-energy pulses at a sub-100 kHz repetition rate

We demonstrate a tunable and switchable dual-wavelength passively mode-locked fiber ring laser in the anomalous dispersion regime that generates high-energy pulses at a sub-100 kHz repetition rate. The nonlinear polarization rotation (NPR) technique is employed in this configuration to allow for passively mode-locked operation. By exploiting the intensity-dependent loss caused by NPR, the mode competition could be efficiently alleviated. Moreover, taking advantage of the intrinsic spectral filter induced by the intracavity birefringence, the dual-wavelength separations as well as the wavelength lasing locations could be flexibly tuned by properly rotating the polarization controller. With a repetition rate of 85.8 kHz, the laser delivers the single pulse energy of 198 nJ at a pump power of 250 mW. The combination of high per-pulse energy and flexible tunability in this fiber laser is useful for practical applications.     

Observation of stable bound soliton with dual-wavelength in a passively mode-locked Er-doped fiber laser

A phase-locked bound state soliton with dual-wavelength is observed experimentally in a passively mode-locked Erdoped fiber(EDF) laser with a fiber loop mirror(FLM). The pulse duration of the soliton is 15 ps and the peak-to-peak separation is 125 ps. The repetition rate of the pulse sequence is 3.47 MHz. The output power is 11.8 mW at the pump power of 128 mW, corresponding to the pulse energy of 1.52 nJ. The FLM with a polarization controller can produce a comb spectrum, which acts as a filter. By adjusting the polarization controller or varying the pump power, the central wavelength of the comb spectrum can be tuned. When it combines with the reflective spectrum of the fiber Bragg grating, the total spectrum of the cavity can be cleaved into two parts, then the bound state soliton with dual-wavelength at 1549.7 nm and 1550.4 nm is obtained.     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

Dark pulses with tunable repetition rate emission from fiber ring laser

We demonstrated the experimental observation of the dark pulses with tunable repetition rate from an erbium-doped fiber ring laser. A considerable length of high nonlinear fiber is incorporated into the fiber ring laser to enhance the nonlinear intensity. In our experiment, both bright and dark pulses can be observed under the conditions of appropriately setting of the device in the cavity. Further study showed that the dark pulse is formed due to the cross coupling between two different lasing wavelengths. Particularly, dark pulse-train with multiple repetition rates was observed from the laser cavity and the repetition rate switchable operation can be realized by simply adjusting the polarization controller (PC) in the cavity. The operation of multiple repetition rates of dark pulses was further experimentally investigated and detected as a result of pulse splitting of each component with different wavelength.     

Sub-100 kHz repetition rate erbium-doped fiber laser in anomalous dispersion regime

We propose and demonstrate a simple but efficient way to generate low repetition rate pulses in an erbium-doped fiber ring laser by using self-pulsing technique. About 2.25 km long single mode fiber is used to elongate in the cavity, providing large anomalous cavity dispersion in the wavelength region around 1550 nm. Self pulses at a repetition rate of 85.3 kHz with single pulse energy as high as 110 nJ are efficiently obtained on the nanosecond time scale. The experimental results demonstrate that the self-pulse fiber laser operating in the anomalous dispersion regime can also realize high-energy pulses at a very low pulse repetition rate.