Nickel deposition on γ-Al2O3 model catalysts: An experimental and theoretical investigation

Recently, surface modifications on a commercial Ni/γ-Al₂O₃ catalyst during the production of methane from synthesis gas were investigated by quasi insitu X-ray photoelectron spectroscopy (XPS) [I. Czekaj, F. Loviat, F. Raimondi, J. Wambach, S. Biollaz, A. Wokaun, Appl. Catal. A: Gen. 329 (2007) 68]. The conclusion was that the reactivity and the observed reaction mechanisms on the different Ni particles are influenced directly by both the size and the composition of the particles on the γ-Al₂O₃ support.In this investigation, Ni deposition and cluster growth on model catalyst samples (10 nm thick, polycrystalline γ-Al₂O₃ on Si(100)) were investigated by XPS. Several steps in the binding energy during Ni deposition indicate changes in the cluster growth. The molecular structure of the catalyst was investigated using Density Functional Theory calculations (StoBe) with a cluster model and non-local functional (RPBE) approach. An Al₁₅O₄₀H₃₅ cluster was selected to represent the γ-Al₂O₃(100) surface. Ni clusters of different size were cut from a Ni(100) surface and deposited on the Al₁₅O₄₀H₃₅ cluster in order to validate the deposition model determined by XPS.     

Influence of hydrothermally modified γ-Al2O3 on the properties of NiMo/γ-Al2O3 catalyst

The influence of hydrothermal modification of γ-Al₂O₃ on the properties of NiMo/γ-Al₂O₃ catalyst was investigated in this paper. The experimental results showed that the use of the modified γ-Al₂O₃ in the preparation of the NiMo/γ-Al₂O₃ catalyst led to the increase of the dispersion of the surface Mo and Ni oxides, favored the formation of the poly-molybdates and promoted the reduction of the active Mo oxides owing to the increase of the surface acidity of the modified γ-Al₂O₃. Therefore, the NiMo/γ-Al₂O₃ catalyst supported on the modified γ-Al₂O₃ exhibited a higher hydrodenitrogenation (HDN) activity than that supported on the untreated γ-Al₂O₃ in the temperature range of 300-340 °C.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Effect of hydrothermal treatment on the acidity distribution of γ-Al2O3 support

The influence of hydrothermal treatment on the total acidity and the acidity distribution of γ-Al₂O₃ were studied in this paper. The experimental results indicated that the hydrothermal treatment of γ-Al₂O₃ at moderate condition (140 °C, 1.0-24.0 h) led to the formation of the plate-like γ-AlOOH crystallites with different morphologies, which resulted in the change of the surface acidity of the corresponding γ-Al₂O₃ supports. The increase of the reaction time in the period of 1.0-2.0 h led to the increase of the specific surface area, the surface OH, the total acidity and the ratio of the weak acidity in the acidity distribution of γ-Al₂O₃. The further prolongation of reaction time caused the overgrowth of γ-AlOOH crystallites, leading to the decrease of the specific surface area, the surface OH and the total acidity of the corresponding γ-Al₂O₃.     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.     

Effect of Li2O and CoO-doping of CuO/Fe2O3 system on its surface and catalytic properties

Physicochemical, surface and catalytic properties of pure and doped CuO/Fe₂O₃ system were investigated using X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX), nitrogen adsorption at −196 °C and CO-oxidation by O₂ at 80-220 °C using a static method. The dopants were Li₂O (2.5 mol%) and CoO (2.5 and 5 mol%). The results revealed that the increase in precalcination temperature from 400 to 600 °C and Li₂O-doping of CuO/Fe₂O₃ system enhanced CuFe₂O₄ formation. However, heating both pure and doped solids at 600 °C did not lead to complete conversion of reacting oxides into CuFe₂O₄. The promotion effect of Li₂O dopant was attributed to dissolution of some of dopant ions in the lattices of CuO and Fe₂O₃ with subsequent increase in the mobility of reacting cations. CoO-doping led also to the formation of mixed ferrite Co_xCu_1−xFe₂O₄. The doping process of the system investigated decreased to a large extent the crystallite size of unreacted portion of Fe₂O₃ in mixed solids calcined at 600 °C. This process led to a significant increase in the S_BET of the treated solids. Doping CuO/Fe₂O₃ system with either Li₂O or CoO, followed by calcination at 400 and 600 °C decreased its catalytic activity in CO-oxidation by O₂. However, the activation energy of the catalyzed reaction was not much affected by doping.     

The surface properties and the activities in catalytic wet air oxidation over CeO2-TiO2 catalysts

No-noble metal CeO₂-TiO₂ catalysts prepared by sol-gel method were developed and examined for catalytic wet air oxidation (CWAO) of acetic acid. The structure of the catalysts was measured by BET, SEM, XRD, XPS and DTA-TG. We investigated the effect of the interactions of Ce and Ti on the structure of CeO₂-TiO₂ catalysts. The mechanisms of the relationships between the different content of Ti and the activity of CeO₂-TiO₂ catalysts were discussed. The results showed that the average crystal size of CeO₂ decreased and the surface areas increased; the low valence of Ce³⁺ increase, and the chemisorbed oxygen slightly decreased with the increase of Ti content on the surface of CeO₂-TiO₂ catalysts. The order of the activity in CWAO of acetic acid followed: Ce/Ti 1/1 > Ce/Ti 3/1 > Ce/Ti 1/3 > Ce/Ti 5/1 > CeO₂ > TiO₂ > no catalyst. In CWAO of acetic acid, the optimal atomic ratio of Ce and Ti was 1, and the highest COD removal was over 64% at 230 °C, 5 MPa and 180 min reaction time over Ce/Ti 1/1 catalyst. The excellent activity and stability of CeO₂-TiO₂ catalysts was observed in our study.     

Highly active Ce1−xCuxO2 nanocomposite catalysts for the low temperature oxidation of CO

A series of Ce_1−xCu_xO₂ nanocomposite catalysts with various copper contents were synthesized by a simple hydrothermal method at low temperature without any surfactants, using mixed solutions of Cu(II) and Ce(III) nitrates as metal sources. These bimetal oxide nanocomposites were characterized by means of XRD, TEM, HRTEM, EDS, N₂ adsorption, H₂-TPR and XPS. The influence of Cu loading (5-25 mol%) and calcination temperature on the surface area, particle size and catalytic behavior of the nanocomposites have been discussed. The catalytic activity of Ce_1−xCu_xO₂ nanocomposites was investigated using the test of CO oxidation reaction. The optimized performance was achieved for the Ce_0.80Cu_0.20O₂ nanocomposite catalyst, which exhibited superior reaction rate of 11.2 × 10⁻⁴ mmol g⁻¹ s⁻¹ and high turnover frequency of 7.53 × 10⁻² s⁻¹ (1% CO balanced with air at a rate of 40 mL min⁻¹, at 90 °C). No obvious deactivation was observed after six times of catalytic reactions for Ce_0.80Cu_0.20O₂ nanocomposite catalyst.     

Microstructure and corrosion resistance behavior of ceramic coatings on biomedical NiTi alloy prepared by micro-arc oxidation

In this paper, ceramic coatings were prepared on biomedical NiTi alloys by micro-arc oxidation (MAO) in constant voltage mode. The current density-time response was recorded during the MAO process. The microstructure, element distribution and phase composition of the coatings prepared at different MAO treatment times were investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), thin-film X-ray diffraction (TF-XRD) and X-ray photoelectron spectroscopy (XPS). The corrosion behavior of the coatings in 0.9% NaCl solution was evaluated by the potentiodynamic polarization test. It is found that the coatings become more compact with increasing the MAO treatment time, and the growth rate of coating decreases. The results of TF-XRD, EDS and XPS indicate that the coatings are composed of a large amount of γ-Al₂O₃ and a little α-Al₂O₃, TiO₂ and Ni₂O₃. The Ni content of the coatings is about 3 at.%, which is greatly lower than that of NiTi substrate. The bonding strength of coating-substrate is higher than 40 MPa for all the samples in this study. The corrosion resistance of the coatings is about two orders of magnitude higher than that of the uncoated NiTi alloy.     

Effect of O-vacancy defects on the Schottky barrier heights in Ni/SiO2 and Ni/HfO2 interfaces

We perform first-principles density functional calculations to study the electronic structure of Ni/HfO₂ and Ni/SiO₂ interfaces and the effect of O-vacancy (V_O) defects on the Schottky barrier height and the effective work function. We generate two interface models in which Ni is placed on O-terminated HfO₂ (1 0 0) and α-quartz (1 0 0) surfaces. As the concentration of V_O defects at the interface increases, the p-type Schottky barrier height tends to increase in the Ni/HfO₂ interface, due to the reduction of interface dipoles, whereas it is less affected in the Ni/SiO₂ interface.     

Hydrogenolysis of methylcyclopentane over the bimetallic Ir-Au/γ-Al2O3 catalysts

The gas-phase hydrogenolysis of methylcyclopentane (MCP) was investigated over the bimetallic Ir-Au/γ-Al₂O₃ catalysts. The bimetallic systems containing the atomic Au/Ir ratios in the range of 0.125-8 and a fixed total metal content of 8 wt.%, were prepared by the sequential impregnation (SI) and co-impregnation (CI) methods. The corresponding monometallic Ir/γ-Al₂O₃ and Au/γ-Al₂O₃ catalysts were also prepared. The materials were characterized by ICP, XRD, N₂ adsorption, TEM, and H₂ chemisorption. Highly dispersed Ir nanoparticles were obtained in all cases, while the size of Au nanoparticles increased (up to 50 nm) upon the increasing Au content in the catalyst. The monometallic gold catalyst did not adsorb H₂. The incorporation of Au increased the amount of irreversible adsorbed H₂ in the Ir-Au/γ-Al₂O₃ catalysts with respect to the monometallic ones. The products obtained in the MCP hydrogenolysis were 2-methylpentane (2-MP), 3-methylpentane (3-MP) and n-hexane (n-H). The initial rate (molecules of MCP reacted s⁻¹ g_Ir⁻¹) increased with the Au content. The deactivation was lower for bimetallic catalysts, particularly for the CI ones. The addition of Au played a significant effect on chemisorption and catalytic properties of Ir.     

Ni与Co掺杂Fe2O3（0001）表面增强析氧反应活性

Fe based oxides are considered as a promising catalyst for the oxygen evolution reaction (OER) due to their low cost and high stability. Here, based on density functional theory calculations, the electrocatalytic behaviors of pure and metal (Ni, Co) doped Fe-terminated Fe₂O₃(0001) are investigated. The potential-limiting step for OER is determined as the formation of O^* by dehydrogenating surface hydroxyl and it is suggested that the doping enhances the catalytic activity of Fe₂O₃(0001) by reducing the free energy change of rate limiting step on doped Ni or Co atom. Especially, the calculated over-potential of Co-doped Fe₂O₃ (0001) surface is about 0.63 eV on Co site, which is comparable with the theoretical over-potential of 0.56 eV for RuO₂.     

The effect of P2O5 on the ultra broadband near-infrared luminescence from bismuth-doped SiO2-Al2O3-CaO glass

The effect of P₂O₅ on infrared luminescence properties of bismuth-doped SiO₂-Al₂O₃-CaO (SAC) glass was investigated. Under excitation of 690 and 808 nm LD, two infrared emissions from bismuth ions central at 1100 and 1300 nm were observed, respectively. The addition of P₂O₅ was not only found to lead to the increase of full width at half maximum (FWHM) of two infrared emissions, but also result in intensity variety of the infrared emissions. The intensity of the infrared emission located at 1300 nm is reduced by a factor of 2, while the luminescence at 1110 nm is increased by a factor of 5. We propose that the infrared emissions at 1100 and 1300 nm may originate from different valence Bi ion in glasses. Compared with emission at 1300 nm, the infrared emissions at 1100 nm is more possibly from the transition of lower valent Bi ion.     

Characterization of Y2O3 gate dielectric on n-GaAs substrates

Physical and electrical properties of sputtered deposited Y₂O₃ films on NH₄OH treated n-GaAs substrate are investigated. The as-deposited films and interfacial layer formation have been analyzed by using X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). It is found that directly deposited Y₂O₃ on n-GaAs exhibits excellent electrical properties with low frequency dispersion (<5%), hysteresis voltage (0.24 V), and interface trap density (3 × 10¹² eV⁻¹ cm⁻²). The results show that the deposition of Y₂O₃ on n-GaAs can be an effective way to improve the interface quality by the suppression on native oxides formation, especially arsenic oxide which causes Fermi level pinning at high-k/GaAs interface. The Al/Y₂O₃/n-GaAs stack with an equivalent oxide thickness (EOT) of 2.1 nm shows a leakage current density of 3.6 × 10⁻⁶ A cm⁻² at a V_FB of 1 V. While the low-field leakage current conduction mechanism has been found to be dominated by the Schottky emission, Poole-Frenkel emission takes over at high electric fields. The energy band alignment of Y₂O₃ films on n-GaAs substrate is extracted from detailed XPS measurements. The valence and conduction band offsets at Y₂O₃/n-GaAs interfaces are found to be 2.14 and 2.21 eV, respectively.     

Acid-base properties of Ni-MgO-Al2O3 materials

Ni-MgO-Al₂O₃ materials of different Ni/Mg ratios were prepared by the co-precipitation method. Acid-base properties of the samples after calcination and reduction were examined by the temperature programmed desorption of ammonia and carbon dioxide. Thermal treatment of the materials in air at 400 °C led to the formation of hydrotalcite-like phases. The increase of Ni/Mg ratio decreased the stability of the hydrotalcite structure. The number and the strength of acid and base sites were related to the Ni/Mg ratio and thermal treatment conditions of materials. It was found that the replacement of Ni with Mg decreased the acidity and increased basicity of the surface of oxide materials. Thermal treatment of the samples in hydrogen led to the structural changes. The presence of magnesia improved thermal stability. The ratio of the number of acid to base sites in the reduced samples gradually increased with the increase of magnesia content.     

Al2O3 supported Ru catalysts prepared by thermolysis of Ru3(CO)12 for catalytic wet air oxidation

Low loading catalysts Ru/γ-Al₂O₃ and Ru-Ce/γ-Al₂O₃ were prepared by thermolysis of Ru₃(CO)₁₂ on γ-Al₂O_3. The catalysts were characterized by XPS, XRD and SEM. Two new Ru species (Ru_A and Ru_B) were detected during the Ru₃(CO)₁₂ decomposition process due to chemical interaction with the active OH groups on the surface of Al₂O₃ support, and the reduction of them can lead to more dispersed metallic phases. The sample was completely decomposed at 673 K in H₂, and RuO₂ was formed with minor amounts of Ru⁰. When the temperature was increased to 773 K to heat the sample, the ratio of Ru⁰ to RuO₂ increased. However, after the addition of CeO₂, only RuO₂ was detected on surface. The catalysts exhibited high activities in Catalytic Wet Air Oxidation (CWAO) of different organic compounds at high concentration such as isopropyl alcohol, phenol, acetic acids and N,N-dimethylformamide, which is attributed to the better dispersion of Ru particles and the addition of CeO₂ further enhanced number of effectively active sites on the cluster-derived catalyst surface.     

X-ray diffraction and photoelectron spectroscopy studies of MoO2 as catalyst for the partial oxidation of isooctane

X-ray diffraction (XRD), X-ray photoemission (XPS) as well as ultraviolet photoemission (UPS) spectroscopy experiments on MoO₂ powders were carried out to examine the bulk, the core level energies, and the electronic structure of MoO₂ samples that were employed as catalysts for the partial oxidation of isooctane. Five fresh 0.5-g MoO₂ samples were exposed for 0, 0.5, 9, 20, and 43 h to identical reforming environments and their spent samples were analyzed using the techniques mentioned above. Our results indicate the rapid appearance of an intermediate Mo phase with a binding energy of 228.5 eV and whose concentration progressively increases with time. The oxidation state for this new phase was graphically estimated to approximately +2.6 and assigned to the compound Mo₂O₃, which forms on the catalyst surface as a result of its exposure to the reforming environment. The electronic structure probed by UPS reveals two bands, one at 1.62 eV and another at 0.55 eV below the Fermi level, that decrease with the increasing time on stream. These results correlate very well with the drop in the catalytic performance of MoO₂ for the partial oxidation of isooctane and with the decline in the concentration of dioxide (Mo⁴⁺) detected not only on the catalyst surface, but also in the bulk structure, as confirmed by our XRD analysis.     

Synthesis and characterization of pure and ZrO2-doped nanocrystalline CuO-NiO system

The physicochemical, surface and catalytic properties of pure and doped 0.25CuO-NiO solids prepared by sol-gel method were investigated. The dopant concentration was 2, 4 and 6 mol% ZrO₂. The solids investigated were calcined at 400 and 600 °C. The techniques employed were XRD, EDX, TEM, surface excess oxygen, nitrogen adsorption at −196 °C and catalytic oxidation of CO by O₂ using both static and flow methods. The results revealed that the investigated system dissolved 4 mol% ZrO₂ by heating at 400 °C. This process was accompanied by a significant increase in the S_BET and V_p with subsequent decrease in the (r) values of the doped adsorbent. ZrO₂-doping of the system investigated followed by calcination at 400 and 600 °C led to a considerable increase in its catalytic activity in CO oxidation by O₂ using static and flow methods. The doping process was not accompanied by any change in the activation energy of the catalyzed reaction.     

Roles of γ-Fe2O3 in fly ash for mercury removal: Results of density functional theory study

First-principle calculations based on density function theory (DFT) are used to clarify the roles of γ-Fe₂O₃ in fly ash for removing mercury from coal-fired flue gases. In this study, the structure of key surface of γ-Fe₂O₃ is modeled and spin-polarized periodic boundary conditions with the partial relaxation of atom positions are employed. Binding energies of Hg on γ-Fe₂O₃ (0 0 1) perfect and defective surfaces are calculated for different adsorption sites and the potential adsorption sites are predicted. Additionally, electronic structure is examined to better understand the binding mechanism. It is found that mercury is preferably adsorbed on the bridge site of γ-Fe₂O₃ (0 0 1) perfect surface, with binding energy of −54.3 kJ/mol. The much stronger binding occurs at oxygen vacancy surface with binding energy of −134.6 kJ/mol. The calculations also show that the formation of hybridized orbital between Hg and Fe atom of γ-Fe₂O₃ (0 0 1) is responsible for the relatively strong interaction of mercury with the solid surface, which suggests that the presently described processes are all noncatalytic in nature. However, this is a reflection more of mercury's amalgamation ability.     

Surface characterization of the Zn-Ni-Al2O3 nanocomposite coating fabricated under ultrasound condition

Zn-Ni-Al₂O₃ nanocomposite coating, which was fabricated by eletrodeposition technique with the aid of ultrasound, was investigated by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis and X-ray photoelectron spectroscopy (XPS). The results reveal that 7.2 wt.% nano-alumina particles uniformly dispersed in the matrix of the composite coating. The XPS analyses demonstrate that the outermost layer of Zn-Ni-Al₂O₃ coating was composed of nano-alumina and Zn(OH)₂, while the transition layer between the outermost layer and the Zn-Ni matrix consisted of nano-alumina, metallic Zn, ZnO and metallic Ni. In order to investigate the influences of ultrasonic agitation and the incorporation of nano-alumina on the composition and surface structure of Zn-Ni matrix, the comparison studies of Zn-Ni-Al₂O₃ nanocomposite coating with Zn-Ni coatings fabricated with and without ultrasound were conducted. The results indicate that ultrasonic agitation resulted in a decrease of Ni content in the Zn-Ni matrix and an increase of the thickness of surface oxide layer; while the incorporation of nano-α-Al₂O₃ increased the Ni content in the Zn-Ni matrix.