Liquid petroleum gas sensing performance of polyaniline-carboxymethyl cellulose composite at room temperature

In the present research, liquid petroleum gas (LPG) sensing properties of polyaniline-carboxymethyl cellulose (PANI-CMC) composite have been investigated. For the purpose of investigation, PANI and PANI-CMC composite are synthesized at room temperature by chemical polymerization of aniline without/with CMC. The prepared materials are characterized by X-ray diffraction (XRD) and Scanning electron microscopy (SEM) techniques. Shift in d-space of PANI in the composite as confirmed by its XRD analysis suggests ordered PANI chain arrangement in the composite. Surface morphology and size of the particles are studied by SEM technique. Nature of the material and mechanism of conduction of both PANI and PANI-CMC composite are investigated by studying complex plane impedance plot in the frequency range of 10²–10⁶ Hz. Based on structural characterizations and impedance studies, sensitivity of PANI and PANI-CMC composite to LPG at room temperature are tested and compared. Further, to examine the efficiency of the composite as a sensor, its stability, recovery and response time have also been studied with a special focus on its ability to work at room temperature.     

Preparation and characterization of reduced graphene oxide supported nickel oxide nanoparticle-based platform for sensor applications

A nanostructured composite film comprising reduced graphene oxide (rGO) and nickel oxide (NiO) nanoparticles (NPs) has been prepared and utilized for development of a simple yet efficient sensor for detection of dopamine and epinephrine in a single run. The hybrid material rGO-NiO nanocomposite was synthesized chemically, and the formation of nanocomposite was confirmed via X-ray diffraction (XRD), transmission electron microscopy (TEM), Raman, UV-Vis, and Fourier transform infrared (FTIR) spectroscopic techniques. The incorporation of NiO NPs on rGO support was found to provide improved sensing characteristics at electrode interface due to enhanced electron mobility on rGO sheet and high catalytic activity of NiO NPs. Subsequently, the synthesized rGO-NiO nanocomposite was deposited onto indium tin oxide (ITO)-coated glass substrate by simple drop-casting method, and the electrode was characterized through atomic force microscopy (AFM) and scanning electron microscopic (SEM) studies. After optimization of experimental conditions electrochemically for its high sensitivity, the fabricated rGO-NiO/ITO electrode was used for simultaneous detection of dopamine and epinephrine by square wave voltammetry (SWV) method. The results showed high sensitivity of 0.545 and 0.638 μA/μM for dopamine and epinephrine respectively in a broad linear range of 0.5–50 μM. Moreover, remarkable detection limits of 0.495 and 0.423 μM were found for dopamine and epinephrine, and the developed sensor exhibited a wide separation of 380 mV between the respective detection peaks of dopamine and epinephrine. Beside this, the proposed sensor was successfully applied in presence of high concentration of interfering agents, ascorbic acid and uric acid, and validated with real serum samples.     

Nanonails structured ferric oxide thick film as room temperature liquefied petroleum gas (LPG) sensor

In the present work, ferric oxide nanonails were prepared by screen printing method on borosilicate glass substrate and their electrical and LPG sensing properties were investigated. The structural and morphological characterizations of the material were analyzed by means of X-ray diffraction (XRD) and Scanning electron microscopy (SEM). XRD pattern revealed crystalline α-phase and rhombohedral crystal structure. SEM images show nanonails type of morphology throughout the surface. Optical characterization of the film was carried out by UV-visible spectrophotometer. By Tauc plot the estimated value of band gap of film was found 3.85 eV. The LPG sensing properties of the ferric oxide film were investigated at room temperature for different vol.% of LPG. The variations in electrical resistance of the film were measured with the exposure of LPG as a function of time. The maximum values of sensitivity and sensor response factors were found 51 and 50 respectively for 2 vol.% of LPG. The activation energy calculated from Arrhenius plot was found 0.95 eV. The response and recovery time of sensing film were found ∼120 s and 150 s respectively. These experimental results show that nanonails structured ferric oxide is a promising material as LPG sensor.     

Synthesis and elevated temperature performance of a polypyrrole-sulfur-multi-walled carbon nanotube composite cathode for lithium sulfur batteries

A sulfur-multi-walled carbon nanotube composite (S/MWCNT) was prepared using a two-step procedure of liquid-phase infiltration and melt diffusion. Polypyrrole (PPy) conductive polymer was coated on the surface of the as-prepared S/MWCNT composite by in situ polymerization of pyrrole monomer to obtain PPy/S/MWCNT composite. The composite materials were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The electrochemical performance of the as-prepared cathode material was investigated at 25, 40, and 70 °C at various rates. It was found that temperature has dual effects on the performance of Li/S cells. Increasing the temperature, on one hand, facilitates the lithium ion transport through the cathode and, on the other hand, leads to faster dissolution of active material into the electrolyte. The PPy coating can effectively trap polysulfides in its porous structure, even at elevated temperatures, leading to the improvement of the discharge capacity, the cycle stability, and the coulombic efficiency. The electrochemical impedance spectroscopy (EIS) results reveal that the PPy coating reduces the formation of passive layer on the cathode surface, even at high temperatures, resulting in a better elevated temperature performance. A high reversible capacity of 945 mAh g^?1 was maintained after 50 cycles for the PPy/S/MWCNT composite at 70 °C at a rate of 0.5 C.     

One‐Dimensional Magnetic Composite of Polypyrrole‐Containing Carbon Nanotubes/Ni0.75Zn0.25Fe2O4

A novel one‐dimensional electromagnetic nanocomposite of polypyrrole (PPY) containing carbon nanotubes (CNTs)/Ni_0.75Zn_0.25Fe₂O₄ was synthesized by an in‐situ polymerization method. The composite was characterized by x‐ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and Fourier transform infrared. The XRD results confirmed that PPY, CNTs, and Ni_0.75Zn_0.25Fe₂O₄ coexisted in the composite. The TEM and HRTEM results indicated that PPY coated the surface of the CNTs/Ni_0.75Zn_0.25Fe₂O₄ with a thickness of 15–30 nm. The lattice spacings, according to the first main peak of the CNTs, Ni_0.75Zn_0.25Fe₂O₄, and PPY, was about 0.34 nm, 0.25 nm, and 0.42 nm, respectively. The FTIR result also indicated that the PPY formed in the composite. A test of magnetic properties indicated that the composite was ferromagnetic with the saturated magnetization of 12.86 electromagnetic units (emu)/g, and the coercive of 127.18 Oersted (Oe).     

Study of alternating current conduction mechanism in polypyrrole-magnesium ferrite hybrid nanocomposite through correlated barrier hopping model

In the present work, both polypyrrole (PPy) and optimized polypyrrole–magnesium ferrite (PPy-MgFe₂O₄) hybrid nanocomposite were synthesized separately by simple oxidative chemical polymerization method and then structurally characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The FTIR spectrum of the composite showed the presence of characteristic absorption bands of both PPy and MgFe₂O₄ in the composite confirming interfacial interaction of PPy with MgFe₂O₄. That this interaction is not affected by crystalline behaviour of predominant MgFe₂O₄ particles but that MgFe₂O₄ has embedded in PPy matrix was confirmed by XRD studies. Agglomerated granular spherical morphology of the composite was confirmed by SEM studies. Decrease in AC conductivity of the composite as compared to PPy due to the formation of interfacial heterojunction barrier between p-type PPy and n-type MgFe₂O₄ was confirmed experimentally and well supported theoretically by calculating binding energy, hopping distance and density of states at Fermi level of PPy and the composite as per CBH model.     

Novel silicon–oxygen–carbon composite with excellent cycling steady performance as anode for lithium-ion batteries

The novel anode material for lithium-ion batteries, silicon–oxygen–carbon (Si–O–C) composite, is prepared by a liquid solidification combined with following pyrolysis process, in which silicon dioxide (SiO₂) is used as an additive agent to enhance the electrochemical performance of the composite. While the structure of the composite is confirmed by X-ray diffraction (XRD) and Fourier transform infrared spectra (FT-IR), the morphology and microstructure were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. SEM and TEM observations reveal that the Si–O–C powders are about 1 μm in diameter, and there is a homogenous pyrolyzed carbon layer about 5 nm thick on the surface of the particle. The Si–O–C sample as anode material can deliver a high initial charge capacity of 753.4 mAh g^?1, and the capacity keeps above 500.0 mAh g^?1 after 40 cycles at 100.0 mA g^?1. The electrochemical impedance spectroscopy results show that the composite exhibits lower charge transfer resistance and higher lithium-ion diffusion rate compared with the Si–C anode, which indicates that the composite Si–O–C could be used as a promising anode material for lithium-ion batteries.

Open image in new window

Graphical Abstract SEM images of the Si-C (a) and Si-O-C (b) samples and the TEM (c) and HRTEM (d) image of the Si-O-C sample

     

Electrocatalytic oxidation of formaldehyde on platinum well-dispersed into single-wall carbon nanotube/polyaniline composite film

Single-walled carbon nanotubes (SWNTs)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dissolved SWNTs. The composite films were dispersed Pt by electrodeposition technique. The presence of SWNTs and platinum in the composite film was confirmed by XRD analysis and scanning electron microscopy (SEM). Four-point probe investigation and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI coated SWNTs in these films enhanced electric conductivity and facilitated the charge-transfer of the composite films. Cyclic voltammogram (CV) and chronoamperogram showed that Pt-modified SWNT/PANI composite film performs higher electrocatalytic activity and better long-term stability than Pt-modified pure PANI film toward formaldehyde oxidation. The results imply that the SWNT/PANI composite film as a promising support material improves the electrocatalytic activity for formaldehyde oxidation greatly.     

SEM and TEM analysis of composite of ZrO2-Ti system

3Y-ZrO₂-Ti composites obtained by slip casting method were studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Moreover, the Vickers hardness was measured. The experiments show the complex microstructure of composites. The tetragonal zirconium dioxide (t-ZrO₂) and monoclinic zirconium dioxide (m-ZrO₂) as a composite matrix were detected at XRD analysis. SEM observations revealed that Ti -rich phase are uniform distributed in composites. Moreover, the large and very fine precipitations were found. The very fine Ti rich precipitations were located at ZrO₂ grain boundaries as well as in the triple-points. TEM experiments confirmed that in the sintered composites 3Y-ZrO₂ – 10%Ti the uniaxial ZrO₂ grains (100–600 nm), fine monoclinic martensitic plates and fine round monoclinic particles (20–40 nm) of ZrTiO₂ phase were exist. The complex microstructures of 3Y-ZrO₂-Ti composites have a high hardness as a result of existing fine ZrTiO₂ and other Ti oxides precipitations.     

Hollow polypyrrole nanosphere embedded in nitrogen-doped graphene layers to obtain a three-dimensional nanostructure as electrode material for electrochemical supercapacitor

A novel approach was developed to prepare hollow polypyrrole (PPy) nanospheres and nitrogen-doped graphene/hollow PPy nanospheres (NG/H-PPy) composites. In this process, uniform poly (methyl methacrylate-butyl methacrylate-methacrylic acid) (PMMA-PBMA-PMAA) latex microspheres as sacrificial templates were synthesized by using an emulsion polymerization method. Then, hollow PPy nanospheres were obtained on the surface of PMMA-PBMA-PMAA microspheres by in situ chemical oxidative polymerization. Finally, H-PPy was embedded in NG layers successfully through a simple approach. The nanobeads have been characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectra, and Fourier transform infrared spectra (FTIR). Different electrochemical methods including cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), and electrochemical impedance spectroscopy (EIS) have been applied to study the electrochemical properties. The specific capacitance of NG/H-PPy composites based on the three-electrode system is as high as 575 F g^?1 at a current density of 1 A g^?1 and enhanced stability about 90.1 % after 500 cycles, indicating that the composite has an impressive capacitance and excellent cycling performance.     

Functional multi-walled carbon nanotube/polyaniline composite films as supports of platinum for formic acid electrooxidation

Embedding of carbon nanotubes in conducting polymeric matrices for various nanocomposites material is now a popular area. In this article, a concise chemical method has been described for the preparation of homogeneous nanocomposite of multi-walled carbon nanotube (MWNT)/polyaniline (PANI) by electrochemical codeposition. For this we functionalized the MWNTs via the diazotization reaction. This helped to disperse the nanotubes in aniline. The composite films were dispersed Pt by electrodeposition technique. The presence of MWNTs and platinum in the composite films was confirmed by XRD analysis and transmission electron microscopy (TEM). Four-point probe investigations revealed that the MWNT/PANI composite films exhibited a good conductivity. Cyclic voltammograms (CV) showed that Pt-modified MWNT/PANI composite films perform higher electrocatalytic activity and better long-term stability than Pt-modified pure PANI film toward formic acid oxidation. The results imply that the MWNT/PANI composite films as a promising support material improves the electrocatalytic activity for formic acid oxidation greatly.     

Degradation of magnetite nanoparticles in biomimetic media

Magnetic nanoparticles (NPs) of magnetite Fe₃O₄ obtained by coprecipitation (COP), thermal decomposition (DT), and commercial sample (CM) have been degraded in similar conditions to physiological medium at pH 4.7 and in simulated body fluid (SBF) at pH 7.4. The formation of the nanoparticles was confirmed by FTIR spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). In view of medical and environmental applications, the stability of the particles was measured with dynamic light scattering. The degradation processes were followed with atomic absorption spectroscopy (EAA) and TEM. Magnetic measurements were carried out using vibrating sample magnetometry (VSM). Our results revealed that the structural and magnetic properties of the remaining nanoparticles after the degradation process were significantly different to those of the initial suspension. The degradation kinetics is affected by the pH, the coating, and the average particle size of the nanoparticles.     

Synthesis and Characterization of La‐Doped Fe3O4‐Polyaniline Magnetic Response Nanocomposites

Lanathum (La)‐doped Fe₃O₄ magnetic nanoparticles were prepared in aqueous solution at room temperature, then La‐doped Fe₃O₄‐polyaniline (PANI) nanocomposites containing a dispersion of La‐doped Fe₃O₄ nanoparticles were synthesized via in‐situ polymerization of aniline monomer. The structure and properties of the synthesized samples were characterized with X‐ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FTIR), thermogravimetric analysis (TGA), inductively coupled plasma atomic emission spectrometry (ICPAES), and a vibrating sample magnetometer (VSM). The resulting particles of La‐doped Fe₃O₄ and La‐doped Fe₃O₄‐PANI were almost spherical with diameters ranging from 15 to 25 nm and 25 to 85 nm, respectively. The La‐doped Fe₃O₄‐PANI composite presented core‐shell structures; polyaniline covered the La‐doped Fe₃O₄ completely. The specific saturation magnetization of La‐doped Fe₃O₄‐PANI depended on the starting material of La‐doped Fe₃O_4. It increased with increasing amounts of La and Fe₃O₄ content.     

Investigation of hydrogen storage in MWCNT–TiO2 composite

The hydrogen storage capacity of MWCNT–TiO₂ composite has been evaluated in the present work. The composite has been prepared by means of ultrasonication followed by drop casting on substrates. Morphology, structural and functional group studies of the prepared samples are carried out by transmission electron microscopy (TEM), scanning electron microscopy (SEM), powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. Then, the samples are hydrogenated in the hydrogenation chamber as a function of time. Hydrogen storage capacity of the composite sample is found to be 0.9 wt% at 100 °C. Hydrogen uptake of the composite is accounted for the spillover mechanism in CNTs–metal oxide composite. Desorption temperature range, activation energy of desorption, binding energy of hydrogen are determined from thermogravimetric (TG) analysis.     

Effect of heat treatment on the mechanical and microstructural characterization of Mg-AZ91E/TiC composites

Mg-AZ91E/TiC_p composite was fabricated using a spontaneous infiltration technique at 950 °C under an argon atmosphere. The composites produced have 37 vol.% of metal matrix and 63 vol.% of TiC-like reinforcement. The obtained composites were subsequently solution heat-treated at 413 °C during 24 h, cold water quenched, and subsequently artificially aged at 168 and 216 °C during 16 h in an argon atmosphere. Effect of heat treatment on the microstructure and mechanical properties was evaluated. Microstructural characterization was analyzed using different techniques such as X-ray diffraction (XRD) and scanning electron microscopy (SEM). Interface between matrix and reinforcement was examined using transmission electron microscopy (TEM), and mechanical properties were evaluated by measuring the elastic modulus and hardness. Mg, TiC, Al, and Mg₁₇Al₁₂ phases through XRD were detected. Meanwhile, using TEM analysis in heat-treated composites MgAl₂O₄, MgO, and Al₂O₃ were identified. The as-fabricated composite have elastic modulus and hardness of 162 GPa and 316 Hv, respectively. After solution heat treatment and aging at 168 °C during 12 h, the composites reaches values of 178 GPa and 362 Hv for the elastic modulus and hardness, respectively. Time of aging was correlated with measures of elastic modulus and hardness.     

Synthesis, characterization and infrared emissivity study of polyurethane/TiO2 nanocomposites

In this study, polyurethane/titania (PU/TiO₂) nanocomposites were prepared in ultrasonic process and characterized by fourier transform IR spectroscopy (FT-IR), powder X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and infrared emissivity analysis. The TEM and SEM results indicated that the nanoparticles were dispersed homogeneously in PU matrix on nanoscale. TGA-DSC confirmed that the heat stability of the composite was improved. Infrared emissivity study showed that the nanocomposite possessed lower emissivity value than those values of pure polymer and nanoparticles.     

Nanoparticles of nickel oxide: growth and organization on zinc-substituted anionic clay matrix by one-pot route at room temperature

A room temperature nanocarving strategy is developed for the fabrication of nanoparticles of nickel oxide on zinc-substituted anionic clay matrix (Ni/ZnLDH). It is based on the growth and organization of nanoparticles of nickel oxide which occur during the structural reconstruction of the layered structure of the anionic clay in NiSO₄ aqueous solution. No organic compounds are used during the fabrication. The described material was characterized by X-ray diffraction (XRD), IR spectroscopy (FTIR), transmission electron microscopy (TEM), field-emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) spectroscopy, and X-ray photoelectron spectroscopy (XPS). Results show that the nickel-clay nanoarchitecture consists of small nanoparticles of nickel oxide (average size 7 nm) deposited on the larger nanoparticles (average size 90 nm) of zinc-substituted clay. The optical properties of the new nickel-zinc formulation are studied by UV–Vis.     

Sonochemical synthesis of polyaniline nanofibers

Conventionally, micro-sized irregular polyaniline (PANI) particles were synthesized by dropwise addition of the ammonium persulfate (APS) solution into the aniline (ANI) solution with mechanical stirring. By replacing the mechanical stirring with an ultrasonic irradiation, PANI nanofibers in diameters of approximately 50 nm and lengths of 200 nm to several micrometers were prepared. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) showed that at the early stage of polymerization, the polymers formed in both the mechanical stirred and ultrasonicated systems are in the form of nanofiber. However, with continuing of the reaction, these primary nanofibers grow and agglomerate into irregular shaped PANI particles in the mechanical stirred system, while in the case of the ultrasonic irradiation, the growth and agglomeration are effectively prevented, preserving thus the PANI nanofibers in the final product. By increasing the APS/ANI molar ratio from 0.5 to 2.5, the aspect ratios of the PANI nanofibers decreased. The PANI nanofibers exhibit higher solubility than the irregular shaped PANI particles. Although the yield, as well as the conductivity of the ultrasonic synthesized PANI nanofibers, was slightly lower than the irregular shaped PANI particles, the ultrasonic synthesis approach is one of the facile and scalable approaches in synthesizing PANI nanofibers in comparison with other ones without use of templates (e.g., the interfacial polymerization and rapid mixing polymerization). UV-Vis and Fourier transformed infrared (FTIR) spectra indicated ultrasound had no significant effect on the chemical structure of the PANI.     

Interphase analysis of hierarchical composites via transmission electron microscopy

Observation and analysis of the interphase are essential for a detailed understanding of the global composite properties when nanofillers are incorporated as interfacial agents. Techniques such as atomic force microscopy and nano-indentation provide valuable information on interfacial properties associated with the viscoelastic behavior of each phase. However, when the morphology of this region is observed in detail, instrumental errors may regularly appear, decreasing the accuracy of measurements. In this work, the use of transmission electron microscopy (TEM) was explored to image the glass fiber-reinforced polymer GFRP interphase containing interfacial nanocellulose. TEM lamellas were prepared via a focused ion beam to observe the phases disposed within the composite arrangement. Energy dispersive X-ray spectroscopy was also performed to determine the elemental composition in each sample phase. Interphase sizes between 25 and 50 nm thick were found, highlighting the ability of this characterization route to give accurate interfacial measurements. This kind of measurement will open new routes for getting rich information on hierarchically structured composites containing a nanostructure as an interfacial agent.     

Preparation and characterization of hexagonal boron nitride and PAMPS-NMPA-based thin composite films and investigation of their membrane properties

The preparation, thermal, morphological, and ion-conducting properties of new composite membranes based on poly(2-acrylamido-2-methyl-1-propanesulfonic acid) (PAMPS) and nitrilotri(methylphosphonic acid) (NMPA)/hexagonal boron nitride (hBN) were carried out throughout this work. Fourier transform infrared (FTIR) spectroscopy was used to characterize the interactions between host polymer, NMPA, and inorganic additive, hBN. Thermal properties of the materials were examined by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) tests. TGA results illustrated that all composite membranes are thermally stable up to 200 °C. The surface topography of the films was investigated by scanning electron microscopy (SEM) and verified that hBN uniformly dispersed into the PAMPS-NMPA matrix. The crystallinity of the membranes was characterized by using X-ray diffraction (XRD). X-ray patterns support semicrystalline nature of the composite materials. At anhydrous conditions, the maximum proton conductivity was found as 3.2?×?10^?5 S cm^?1 at 150 °C for PAMPS-NMPA-3hBN via impedance analyzer.