LD泵浦Nd:YAG 946 nm/1 064 nm双波长运转及腔内和频

用国产半导体激光二极管(LD)端面泵浦NdYAG晶体, 通过优化激光谐振腔反射膜系,调节1 064 nm谱线的线性损耗以达到与弱谱线946 nm的增益匹配,在室温下实现1 064 nm和946 nm双波长连续运转,并通过I类临界相位匹配LBO晶体腔内和频在国内首次实现500.8 nm青色激光连续输出.当泵浦注入功率为1.4W时和频青色激光最大输出达20 mW,光-光转换效率为1.4%,功率稳定性24 h内优于±3%.     

BIBO腔内和频593 nm激光器

采用激光二极管纵向泵浦Nd∶YVO4晶体，用一个线性平凹腔实现了1064 nm和1342 nm双波长连续波振荡，经BIBO腔内和频得到了593 nm的激光输出.当泵浦输入功率为1.4 W时593 nm激光输出功率为48.5 mW. 593 nm激光功率的均方根稳定性＜2.0%，光斑椭圆度为0.90，峰-峰值噪音小于0.5%.     

LD抽运Nd:YVO4/KTP复合腔和频黄光激光器

在LD抽运的三镜复合腔Nd:YVO4激光器中,采用Ⅱ类临界相位匹配的KTP晶体对1064 nm和1342 nm两种波长激光进行和频,获得593 nm黄光连续输出.理论上从速率方程出发,导出1064 nm激光谐振腔和1342 nm激光谐振腔腔长之间的关系以及两个腔的腔镜透过率之间的关系.实验中,当808 nm抽运光的功率为12 W时,和频输出的黄光功率为340 Mw.光-光转换效率为2.8%.结果表明,采用三镜复合腔结构进行腔内和频是实现593 nm黄光输出的一种有效方法.     

LD泵浦Nd:YVO_4双波长运转腔内和频491nm激光器

分析了Nd:YVO4激光器实现双波长运转及腔内和频的条件,利用一种LD泵浦Nd:YVO4晶体产生1 064 nm和914 nm双波长激光束,采用一个线性平凹腔结构,利用腔内Ⅰ类临界相位匹配LBO和频,获得了连续波输出的全固态激光器。实验采用端面结构,在5.0 W的808 nm泵浦功率下,获得了最高功率为2.5 mW连续波TEM00的激光输出,光-光转换效率为0.05%。     

LDA抽运Nd∶YAG/KTP腔内和频589nm连续波激光器

报道了一种激光二极管阵列(LDA)抽运Nd∶YAG双波长和频黄光激光器.黄激光是由Nd∶YAG晶体的1064 nm和1319 nm谱线腔内和频产生.以KTP为和频晶体,采用Ⅱ类临界相位匹配,在12 W的808 nm抽运功率下,获得了最高功率为430 mW连续波基横模的589 nm黄激光输出,光光转换效率为3.6%,光束质量因子M2<1.2.实验结果表明采用激光二极管阵列抽运Nd∶YAG/KTP腔内和频技术是获得黄激光的高效方法,并可以应用到其它激光增益介质的两条谱线进行腔内和频,获得更多不同颜色的单谱线激光输出.     

LDA抽运Nd:YAG/KTP腔内和频589 nm连续波激光器

报道了一种激光二极管阵列（LDA）抽运Nd:YAG双波长和频黄光激光器黄激光是由Nd:YAG晶体的1064 nm和1319 nm谱线腔内和频产生以KTP为和频晶体,采用Ⅱ类临界相位匹配,在12 W的808 nm抽运功率下,获得了最高功率为430 mW连续波基横模的589 nm黄激光输出,光光转换效率为3.6%,光束质量因子M2<1.2实验结果表明采用激光二极管阵列抽运Nd:YAG/KTP腔内和频技术是获得黄激光的高效方法,并可以应用到其它激光增益介质的两条谱线进行腔内和频,获得更多不同颜色的单谱线激光输出     

500.8 nmNd∶YAG青光激光器光学薄膜的设计与制备

从双波长激光运转及和频的机理出发，对LD泵浦Nd∶YAG，LBO腔内和频500.8 nm〖JP2〗青光激光器所使用的光学薄膜进行了设计和制备.在激光反射镜的设计上，为了达到最佳的和频输出，对膜系要求进行了深入分析.采用对谐振腔一端面反射率固定不变并通过对另一腔镜基频光的透射率进行调谐的方法, 在给出合理初始结构后，利用计算机对膜厚进行了优化.并采用双离子束溅射沉积的方法，通过时间监控膜厚法成功制备出青光激光器所使用的全介质激光反射膜, 在室温下实现946 nm和1064 nm双波长连续运转，并通过Ⅰ类临界相位匹配LBO晶体腔内和频在国内首次实现500.8 nm青色激光连续输出.当泵浦注入功率为1.4 W时和频青光最大输出达20 mW.     

500.8nm Nd∶YAG青光激光器光学薄膜的设计与制备

从双波长激光运转及和频的机理出发,对LD泵浦Nd∶YAG,LBO腔内和频500.8nm青光激光器所使用的光学薄膜进行了设计和制备·在激光反射镜的设计上,为了达到最佳的和频输出,对膜系要求进行了深入分析.采用对谐振腔一端面反射率固定不变并通过对另一腔镜基频光的透射率进行调谐的方法,在给出合理初始结构后,利用计算机对膜厚进行了优化.并采用双离子束溅射沉积的方法,通过时间监控膜厚法成功制备出青光激光器所使用的全介质激光反射膜,在室温下实现946nm和1064nm双波长连续运转,并通过Ⅰ类临界相位匹配LBO晶体腔内和频在国内首次实现500.8nm青色激光连续输出.当泵浦注入功率为1.4W时和频青光最大输出达20mW.     

LBO Ⅰ类临界相位匹配内腔和频555 nm激光器

报道了全固态连续波555 nm激光器.555 nm激光是分别由Nd:YAG和Nd:YVO4晶体的946 nm和1342 nm谱线非线性和频产生,两条谱线在各自晶体对应能级跃迁分别为4F3/2-4Ⅰ9/2和4F3/2-4Ⅰ13/2.实验中采用复合折叠腔结构,利用LBOI类临界相位进行腔内和频,当注入Nd:YAG和Nd:YVO4晶体的泵浦功率分别为20 W和10 W时,获得1.06 W的TEM00连续波555 nm激光输出.4小时功率稳定度优于±3.3%.实验结果表明采用两种激光晶体进行腔内和频是获得激光的高效方法,并可以应用到其它两种激光晶体进行腔内非线性和频,获得更多不同波长激光输出.     

LD泵浦355nm准连续紫外激光器

报道了一台LD侧面泵浦Nd:YAG晶体的内腔三次谐波转换的全固态准连续紫外激光器。在谐振腔内,1064nm的基频波通过对Ⅱ类相位匹配KTP晶体进行二倍频来产生532nm波长激光,二者再通过对Ⅱ类相位匹配LBO晶体进行和频来获得355nm紫外激光输出。355nm全固态紫外激光器在声光调Q重复频率为2.8kHz下,当输入电流为18A时可得到503mW的激光输出。     

Diode-pumped 593.5 nm cw yellow laser by type-I CPM LBO intracavity sum-frequency-mixing

A design of LD-pumped Nd:YVO₄ laser that generates simultaneous laser action at wavelengths 1064 and 1342 nm by optimizing film design is presented. An optimized continuous-wave (cw) yellow laser at 593.5 nm in room temperature is obtained for the first time. Using type-I critical phase-matching (CPM)LBO crystal, a yellow laser at 593.5 nm is obtained by 1064 and 1342 nm intracavity sum-frequency mixing. The maximum laser output power of 85 mW is obtained when an incident pump laser of 1.8 W is used. The optical-to-optical conversion is up to 4.7%, and the power stability in 24 h is better than ±2.8%.     

All-solid-state continuous wave doubly linear resonator sum-frequency mixing yellow laser

We report a continuous-wave (CW) yellow laser emission by sum-frequency mixing in Nd:YVO4 crystal. Using type-II critical phase-matching KTP crystal, a yellow laser at 593.5 nm is obtained by 1064 and 1342 nm intracavity sum-frequency mixing. The maximum laser output power of 2.1 W is obtained when an incident pump laser of 18.2 W is used. At the output power level of 2.1 W, the output stability is better than 3.2%.     

3.62 W of continuous-wave orange-yellow light generated by intra-cavity sum-frequency mixing of Nd:YVO4

A design of laser-diode array (LDA) end-pumped Nd:YVO₄ laser that generates simultaneous laser action at wavelengths 1064 and 1342 nm is presented. Using type-I critical phase matching (CPM) BiB₃O₆, 593.5 nm continuous-wave (cw) Orange-yellow laser is obtained by 1064 nm and 1342 nm in an intra-cavity sum-frequency mixing. The maximum laser output power of 3.62 W is obtained when an incident pump laser of 27.5 W is used. The optical-to-optical conversion is up to 13.2%. To the best of our knowledge, this is the highest conversion efficiency at 593.5 nm in an intra-cavity sum-frequency Nd:YVO₄ laser.     

All-solid-state doubly resonant intracavity frequency sum mixing orange yellow laser with 3.2 W output power at 593.5 nm

A compact and efficient 593.5 nm orange-yellow laser is realized using doubly resonant intracavity sum frequency mixing. Two Nd: YVO₄ crystals are employed as the gain crystals. In two sub-cavities, 1064 nm radiation from one Nd: YVO₄ and 1342 nm radiation from the other Nd: YVO₄ are mixed to generate 593.5 nm orange-yellow laser. In the overlapping of the two cavities, sum frequency mixing is achieved in a type I critical phase matching (CPM) LBO crystal. An output power of 3.2 W at the wavelength of 593.5 nm is obtained with total incident pump power of 38 W. The optical to optical conversion efficiency is up to 8.4% and the stability of the output power is better than 2.48% in 8 h. To the best knowledge, this it the highest watt-level laser at 593.5 nm generated by diode end pump all-solid-state technology.     

Continuous-wave simultaneous dual-wavelength and power-ratio-tunable operation at 1064 and 1342 nm in an Nd:LuVO<Subscript>4</Subscript> laser

This study demonstrates continuous-wave simultaneous dual-wavelength emission at 1064 and 1342 nm in an Nd:LuVO₄ laser by using a T-type cavity configuration. The output powers indicating a function of pump power had two evolutions depending on the strength of the completion of two wavelength emissions. One is that the output power increased linearly with the pump power in weak competition, and the output power and slope efficiency of 1064 and 1342 nm were 1.17 W and 13%, and 0.213 W and 2.8%, respectively. The other is that the extracting-energy capabilities of two wavelength emissions were close, and the evolution was not linear and the variations demonstrated multiple stages depending on the pump power. Moreover, the ratio of output power, defined as the output power at 1064 nm divided by that at 1342 nm, is tuned from 0 to 5.5 by varying the 1064 nm cavity, and equal output powers of 1064 and 1342 nm can be obtained at each pump power.     

Dual-wavelength oscillation at 1064 and 1342 nm in a passively Q-switched Nd:YVO<Subscript>4</Subscript> laser with V<Superscript>3+</Superscript>:YAG as saturable absorber

The efficient dual-wavelength oscillation at 1064 and 1342 nm in the passively Q-switched laser based on Nd:YVO₄/V³⁺:YAG is successfully obtained, as demonstrated in this paper. A total average output power of 2.2 W is obtained with 1.3 W for 1064 nm and 0.9 W for 1342 nm under the incident pump power of 7.7 W, corresponding to a total optical-optical conversion efficiency of 28.2%. The pulse widths are 58 and 54 ns for 1064 and 1342 nm, respectively, with the repetition rate of 89 kHz. Moreover, a rate equation model considering the Gaussian spatial distributions of the intracavity photon density and the initial population-inversion density is presented to characterize the dual-wavelength passive Q-switching operation.     

Red, yellow, green and blue – four-color light from a single, aperiodically poled LiTaO3 crystal

We demonstrate simultaneous quasi-continuous wave generation of red, yellow, green and blue coherent radiation based on quadruple quasi-phase matching (QPM) frequency upconversion from a single, aperiodically poled LiTaO₃ (APPLT) crystal with a diode-pumped Nd:YVO₄ dual-wavelength laser oscillating at 1342 and 1064 nm. We designed and prepared an APPLT crystal, which can provide four pertinent reciprocals for simultaneous quadruple QPM processes. Namely, frequency doubling of 1342 nm generates red light at 671 nm, sum-frequency mixing of 1342 nm and 1064 nm produces yellow light at 593 nm, frequency doubling of 1064 nm achieves green light at 532 nm and sum-frequency mixing of 1342 nm and 671 nm obtains blue light at 447 nm. PACS 42.65.Ky; 42.79.Nv; 42.55.Xi; 42.72.Bj     

Efficient generation of continuous-wave yellow light by single-pass sum-frequency mixing of a diode-pumped Nd:YVO(4) dual-wavelength laser with periodically poled lithium niobate

We report efficient generation of cw yellow light by use of single-pass sum-frequency mixing from a diode-pumped Nd:YVO(4) dual-wavelength laser with periodically poled lithium niobate. A diode-pumped Nd:YVO(4) dual-wavelength laser is implemented with a three-mirror cavity, and the optimum oscillation condition is obtained from theoretical analysis. We extracted 78 mW of power at 593 nm from 1.2 W at 1064 nm and from 1.0 W at 1342 nm in a beam with excellent quality. The output power could probably be increased to ~92 mW by antireflection coating of the crystal.     

Noise characteristic of sum-frequency mixing orange solid-state laser

A laser-diode-pumped Nd:YVO₄ orange solid-state laser is described in this paper. The fundamental wavelengths at 1064 and 1342 nm oscillate simultaneously and generate the 593.5 nm wavelength by intracavity sum-frequency mixing in a KTP crystal using type II phase matching. The noise characteristic of laser output has been measured and analyzed at different pumping powers. The relationship between the amplitude noise of sum-frequency mixing output and the longitudinal modes of fundamental frequency has been investigated. The results show that the sum-frequency mixing output has low noise if one of the fundamental wavelengths is single longitudinal mode. The experiment shows that amplitude noise of the intracavity sum-frequency mixing laser is lower than that of intracavity frequency doubled laser with the same structure.