光子晶体四信道波分复用器的研究

提出了一种由2-D光子晶体构成的四信道波分复用系统。该系统包括利用光子晶体的线缺陷实现的波导部分和利用光子晶体微腔实现的频率选择部分。采用时域有限差分(FDTD)方法,研究了光在含点缺陷(即微腔)和线缺陷(即波导)的光子晶体中的传输特性,并给出了仿真结果。计算结果表明,该结构可以实现波长为λ=1550nm附近的四信道波分复用。     

二维异质结光子晶体中含近邻点缺陷的弯曲波导的可调谐滤波特性

应用时域有限差分(FDTD)法,对光在二维异质结光子晶体中含两个近邻点缺陷直角弯曲波导的传输特性进行了数值模拟研究。计算结果表明,具有特定本征共振频率的光子晶体微腔(点缺陷),可将在其邻近波导中传播的相同频率成分的光波"引入"到微腔中。"引入"的频率依赖于异质结光子晶体弯曲波导和微腔的参量,从而能够实现调变"引入"频率。通过改变点缺陷周围介质材料(液晶)的折射率或相关介质柱半径,可分别实现约31 nm或12 nm的波长调谐范围。计算结果为光通信中的调谐、上/下载滤波器,提供了一条新的设计思路和依据。     

一种紧凑的、可调的、基于缺陷共振的光开关

采用平面波展开法(PWM)和时域有限差分(FDTD)法,研究光在含点缺陷的光子晶体波导中的传输特性.计算结果表明,通过引入两共振腔(点缺陷),处于共振频率附近的光波将被完全反射回光子晶体波导.由于共振频率随点缺陷的折射率的变化而改变,这种现象可用来设计可调光开关. 关键词： 光子晶体波导 缺陷共振 光开关 透射率     

光子晶体耦合腔光波导慢光结构特性研究

研究了用于光缓存的光子晶体耦合腔光波导的结构对慢光传输特性的影响.详细讨论了微腔间距关于波导禁带、导模带宽、导模传输群速度的具体关系.计算发现,随着微腔之间距离的增加导模显著平坦化,群速度急剧减小.当相邻微腔之间距离为7个晶格常数时,获得了小于2×10~(-4)c的超小群速度.通过长度为13.23 μm的7×7超胞构成的光子晶体耦合腔光波导,产生的最大光延迟超过了400 ps,这比相同长度传统光波导产生光延迟大四个数量级.     

高透射率慢光速的光子晶体耦合腔波导的研究

将二维三角晶格光子晶体波导和微腔结构结合,优化设计了一种二维三角晶格光子晶体共振耦合腔波导,运用时域有限差分法(FDTD)模拟共振耦合腔波导TE偏振光的透射谱,通过透射谱得到传输光的透射率和群速度。结果表明,合适参数的二维三角晶格共振耦合腔波导在波长1.551μm处的群速度为c/130、透射率为20.1%,在波长1.502μm处的群速度为c/50、透射率为29.2%。运用平面波展开法(PWE)计算的该波导的能带结构对慢光特性进行了分析。这种慢光特性的光子晶体波导将在光存储、光延迟及光子集成等方面有潜在的应用价值。     

基于环形微腔的多频段三角晶格光子晶体耦合腔波导光学传输特性

本文理论研究了近红外波段硅基三角晶格光子晶体环形微腔的光场局域特性,通过将微腔在空间周期性排列组成耦合腔光波导,研究了多个导带区域内光束传输时的群速度,最大和最小值分别为0.0028c和0.00028c.将环形微腔在垂直于光传输方向上进行交错排列,通过改变相邻微腔之间的耦合区域,可以大幅降低多频段范围内光束在耦合腔波导中传输时群速度之间的差异,并提高部分频段的透过率数值.在不改变介质柱半径条件下,通过去掉三角晶格光子晶体中距中心介质柱距离分别为2a和√3a的六个介质柱构成了两种微腔,研究了两种微腔所支持的谐振波长之间的差异,在此基础上构造了两种耦合腔波导,进而将这两种耦合腔光波导与W1型输入/输出波导相连,最终实现了在多个不同频率范围内降低群速度的同时实现频段选择和频段分束功能,其导模群速度可降低到0.00047c.     

液晶调制光子晶体微腔光衰减器

设计了一种二维液晶调制光子晶体微腔光衰减器。两条二维三角晶格空气孔光子晶体波导由一个光子晶体微腔连接,在微腔的点缺陷中填充苯乙炔类液晶。通过施加不同电压,电场诱导液晶取向以改变液晶的折射率,从而改变光子晶体微腔的谐振波长,进而实现光传播强度调节。运用时域有限差分方法和平面波展开法分析了二维液晶调制光子晶体微腔光衰减器的光学特性。数值计算结果表明:对于1.55μm通信波段,通过外界电场控制所填充的向列相液晶的方向可以对这种二维液晶调制光子晶体微腔光衰减器实现3.40%～99.58%的可调谐光输出。     

平行光子晶体波导的传输特性及应用

采用时域有限差分法研究两平行光子晶体波导的传输特性及模场分布,利用耦合模理论计算光子晶体波导的耦合系数。计算结果表明,在不同的频率范围内两平行光子晶体波导之间表现出不同的耦合特性:在高频段(0.32~0.44)(ωa/2πc)的范围内两直波导表现出相互的能量交换,实现光耦合,耦合系数随入射波 频率增加而减小;而在低频段(0.29~0.32)(ωa/2πc)的范围内,两波导的传输谱图几乎重合。最后,提出一种采用固定波导耦合长度同时实现光分束及光均分器的方案,当耦合长度取34a时,可将频率为0.333 (ωa/2πc)和 0.357(ωa/2πc)的两入射波分束传播,同时将低频段中的任意频率波进行能量均分。     

光控液晶光子晶体微腔全光开关

设计了一种缺陷模迁移光子晶体微腔全光开关. 两条二维三角晶格空气孔光子晶体波导由一个光子晶体微腔连接, 在微腔的点缺陷中填充掺有少量偶氮聚合物的苯乙炔类液晶. 通过调节控制光的偏振态, 使偶氮聚合物发生顺-反异构化反应, 带动液晶分子重新取向, 从而改变光子晶体微腔的谐振波长, 进而实现光的通过与截止. 运用时域有限差分法和平面波展开法分析 了二维光控液晶光子晶体微腔全光开关的光学特性. 数值计算结果表明: 对于1.55 μ通信波段通过外界偏振光控制所填充的向列相液晶 的折射率可以实现对光波的导通与截止. 分析结果显示, 此开关具有阈值低, 消光比较大, 体积小等优点. 关键词： 二维光子晶体微腔 波导 时域有限差分(FDTD) 液晶     

二维光子晶体六通道波分复用器的透射谱

设计了一种由微米尺度二维光子晶体构成的六通道波分复用系统。该系统包括利用光子晶体线缺陷实现的波导部分和利用光子晶体微腔实现的频率选择部分。采用时域有限差分方法（FDTD）,研究光在该系统中的传输特性。     

Single-longitudinal-mode fiber laser with a passive multiple-ring cavity and its application for video transmission

A single-longitudinal-mode erbium-doped fiber laser with a passive multiple-ring cavity (MRC) is proposed for the first time to the authors' knowledge. The laser is fundamentally structured by insertion of three different short ring cavities, which serve as mode filters, into the main cavity. When it is combined with a mode-restricting intracavity fiber Bragg grating, the MRC resonator ensures single-longitundinal-mode laser oscillation. The laser can successfully suppress side-mode frequencies of as much as 1 GHz and provide an output power of 23 mW with a side-mode suppression ratio of 51 dB at 1533 nm. The short-term linewidth of the laser output measured is ~2 kHz . The ability of this fiber laser to act as an AM transmitter source is also demonstrated.     

角度调谐滤光片特性分析及膜系设计

对窄带滤光片的倾斜入射特性作了分析.斜入射时其透射通带和峰值会向短波方向移动,透射曲线的稳定性跟滤光片的间隔层结构相关,多腔间使用相同的间隔层可以保证斜入射时有稳定的峰值透射率和带宽,利用该特点可以制备角度调谐窄带滤光片.透射光S和P偏振分量的中心波长随入射角度的增大出现分离现象,产生较大的偏振相关损耗.通过搭配不同厚度的高低折射率材料作为间隔层,改变其有效折射率,使其两个偏振分量的中心波长实现重合.设计了符合密集波分复用(Dense Wavelength Division Multiplexing,DWDM)系统要求的低偏振相关损耗四腔窄带角度调谐滤光片膜系,其可调谐范围达20 nm以上,并评估了所设计角度调谐滤光片的调谐性能.     

Non-linear behaviour and stability of trapped micron-sized cylindrical gas bubbles in an ultrasonic field

Stable arrays of cylindrical bubbles with diameters 3 and 4 μm were produced by trapping air in the pores of hydrophobic Nuclepore filters. These bubble arrays were irradiated by beams of cw and pulsed ultrasound at carrier frequencies near the resonance frequencies of the trapped bubbles. By examining the frequency spectrum of the field scattered by the arrays it was found that the bubbles may oscillate as non-linear stable cavities of long duration. Using short pulses, the bubbles remain stable up to excitation pressure amplitudes of several bars. Mechanisms for the eventual growth and decay of the bubbles are discussed in light of the observations.     

Terahertz bandpass filters using double-stacked metamaterial layers

Bandpass filters are reported based on double-stacked metamaterial layers separated by an air gap for operation at terahertz frequencies. Several stacking configurations were investigated designed for a ~0.5 THz center frequency. The filters exhibited improved spectral transmission properties when compared with conventional ones based on single metamaterial layers. 3 dB bandwidth of ~78 GHz and sidelobe suppression ratio >16 dB were determined when symmetric or asymmetric double layers were stacked. We demonstrate that superior frequency selectivity can be achieved when metamaterial layers with different unit cells are used. Good agreement was found between measured and simulated transmission response.     

Optical properties of the direct-coupled Y-branch filtersby using photonic crystal slabs

We fabricated a new type of two-dimensional photonic crystal slab filter. The resonant cavities were directly put into the waveguide arms. The optical transmissions of the filters were measured and the results show that the optimized two-channel filters give good intensity distribution at the output ports of the waveguide. A minimum wavelength spacing of 5~nm of the filter outputs isrealized by accurately controlling the size of the resonant cavities.     

Scattering of focused ultrasonic beams by cavities in a solid half-space

The ultrasonic field generated by a point focused acoustic lens placed in a fluid medium adjacent to a solid half-space, containing one or more spherical cavities, is modeled. The semi-analytical distributed point source method (DPSM) is followed for the modeling. This technique properly takes into account the interaction effect between the cavities placed in the focused ultrasonic field, fluid-solid interface and the lens surface. The approximate analytical solution that is available in the literature for the single cavity geometry is very restrictive and cannot handle multiple cavity problems. Finite element solutions for such problems are also prohibitively time consuming at high frequencies. Solution of this problem is necessary to predict when two cavities placed in close proximity inside a solid can be distinguished by an acoustic lens placed outside the solid medium and when such distinction is not possible.     

Optical properties of the two-port resonant tunneling filters in two-dimensional photonic crystal slabs

We have designed and fabricated two types of two-port resonant tunneling filters with a triangular air-hole lattice in two-dimensional photonic crystal slabs.In order to improve the filtering efficiency,a feedback method is introduced by closing the waveguide.It is found that the relative position between the closed waveguide boundary and the resonator has an important impact on the dropping efficiency.Based on our analyses,two different types of filters are designed.The transmission spectra and scattering-light far-field patterns are measured,which agree well with theoretical prediction.In addition,the resonant filters are highly sensitive to the size of the resonant cavities,which are useful for practical applications.     

Resonant waveguide device with vertical gratings

Transmission resonant filters in a waveguide with vertical gratings have been realized in silicon on insulator wafers. Experimental studies of fabricated devices show a broad stopband of approximately 19 nm in the center of which exists a narrow transmission band of approximately 0.5 nm with a quality factor of approximately 3000. These resonant cavities are useful for laser cavities, switches, modulators, detectors, and tunable filters.     

Design and model of wideband absorber made of ultrathin metamaterial structures

A planar microwave ultrathin broadband absorber is proposed. It is composed of metallic patterns arranged on a dielectric material which is backed by a copper plate. The patterns of different dimensions allow to judiciously design absorption peaks at specific frequencies of interest. These peaks are due to the mode resonances of the cavities formed by the metallic patches, the dielectric substrate and the copper plate. In order to widen the absorption bandwidth, patterns of different dimensions are used, together with the different modes of these cavities. Numerical and experimental results are presented to validate the proposed method at microwave frequencies. It is also shown that the use of a composite air dielectric substrate supporting the metallic patterns helps to increase the absorption level.