基于偏振门的动态光散射颗粒测量法的研究

为了解决动态光散射纳米颗粒测量技术无法测量高浓度颗粒粒径的难题,提出了一种基于偏振门的动态光散射测量法。从动态光散射和Mie理论出发,理论分析了在高浓度溶液下多重散射效应对散射光偏振态和颗粒粒度测量结果的影响。根据散射光偏振特点,结合偏振门检测技术,改进了传统的动态光散射光学系统。实验研究了在低浓度和高浓度溶液时,不同偏振角度下的散射光强和粒度测量值,完善了散射光的偏振理论。采用90°偏振门检偏,通过各种浓度下的实验,证明了方法的可行性。该方法较之目前同类方法具有原理和结构简单,系统易于维护的特点。     

单光束互相关法测量高浓度纳米颗粒粒径

针对光子相关光谱法不能测量高浓度纳米颗粒粒径和双光束互相关测量法装置结构过于复杂等问题,提出了一种基于范西特-泽尼克定理的单光束互相关法。首先分析了传统双光束互相关法存在的问题,然后根据范西特-泽尼克定理建立了单光束互相关测量法的模型,设计完成了单光束互相关颗粒粒度测量装置,最后对各种浓度不同粒径的颗粒进行了测量。实验证明,单光束互相关法能有效抑制多重散射的影响,适用于测量高浓度纳米颗粒粒径。     

光全散射法颗粒测量中的一种自适应非独立模式算法

光全散射颗粒测量法中需求解第一类Ｆｒｅｄｈｏｌｍ积分方程。在不知道被测颗粒的尺寸范围的情况下如何确定积分方程的上下限、即测量范围，迄今仍是个问题。本文针对此问题提出了一种自适应非独立模式算法。该算法可根据双参数颗粒分布函数的分布参数Ｋ自动确定积分的上下限．数值模拟和实验都证实了此算法。     

双峰分布颗粒体系的多角度动态光散射数据反演

采用多角度动态光散射和加权正则化反演方法,对4组模拟的双峰分布颗粒体系(100/600 nm,200/600 nm,300/600 nm和350/600 nm)分别选取1、3、6和10个散射角进行测量.粒度反演结果表明,采用加权正则化方法反演双峰颗粒体系的多角度动态光散射测量数据,可获得峰值位置比小于2∶1且含有大粒径(＞350 nm)颗粒的双峰颗粒粒度分布.采用标准聚苯乙烯乳胶颗粒进行实测的结果验证了这一结论.得到含大粒径颗粒的双峰粒度分布反演结果的原因在于,多角度动态光散射能提供更多的大粒径颗粒的粒度信息,加权正则化反演方法能减少测量数据中的噪声,因而多角度动态光散射测量数据的加权反演能实现峰值位置比小于2∶1且含有大粒径颗粒的双峰颗粒体系的测量.     

基于后向散射的高浓度纳米颗粒粒度分布测量方法研究

传统的动态光散射法通常采集侧向散射进行纳米颗粒粒度分布的测量,由于多次散射的影响,利用侧向散射不能准确测量高浓度样品的颗粒粒度分布。针对该问题,对后向散射测量方法进行了研究,在实验基础上提出了后向散射最佳光程的判断准则。在不同样品浓度下,用侧向散射和后向散射方法对标称粒径分别为110 nm、220 nm的聚苯乙烯乳胶球颗粒进行了测量。实验结果表明,对于高浓度的待测样品,后向散射测量方法通过自适应调整光程,在最优光程处进行测量,能够有效得到高浓度纳米颗粒的粒径及粒度分布,测量结果相对误差为2.72%。     

双峰分布颗粒体系的多角度动态光散射数据反演（英文）

采用多角度动态光散射和加权正则化反演方法,对4组模拟的双峰分布颗粒体系(100/600nm,200/600nm,300/600nm和350/600nm)分别选取1、3、6和10个散射角进行测量.粒度反演结果表明,采用加权正则化方法反演双峰颗粒体系的多角度动态光散射测量数据,可获得峰值位置比小于2∶1且含有大粒径(350nm)颗粒的双峰颗粒粒度分布.采用标准聚苯乙烯乳胶颗粒进行实测的结果验证了这一结论.得到含大粒径颗粒的双峰粒度分布反演结果的原因在于,多角度动态光散射能提供更多的大粒径颗粒的粒度信息,加权正则化反演方法能减少测量数据中的噪声,因而多角度动态光散射测量数据的加权反演能实现峰值位置比小于2∶1且含有大粒径颗粒的双峰颗粒体系的测量.     

光栅参数测量技术研究进展

光栅参数测量技术是衡量光栅制作水平的重要标准。本文从直接测量法和间接测量法两个角度对现阶段较成熟的光栅参数测量技术进行了研究。重点介绍了原子力显微镜（AFM）测量法、扫描电子显微镜（SEM）测量法、激光衍射（LD）测量法以及散射测量术的测量原理和研究进展,指出了这些方法各自的优缺点和适用范围。AFM测量法和SEM测量法均可测得光栅的局部形貌信息,可用于检测光栅表面形貌缺陷;LD测量法和散射测量术反映的是激光照射区域的平均结果,其中LD测量法能得到光栅周期参数,而椭偏测量术能得到光栅周期以外的其他形貌参数。这些方法测得的光栅参数结果比较吻合,其中LD测量法不确定度最小,AFM次之,SEM最大。文章最后对未来光栅参数测量技术的发展方向进行了论述。     

夫琅和费衍射颗粒粒度测量中的改进Chin-Shifrin反演算法

在基于线阵CCD的夫琅和费衍射颗粒粒度测量中,采用Chin-Shifrin积分变换反演算法使得反演的粒度分布出现假峰现象.为解决此问题,提出在该Chin-Shifrin积分变换反演算法中引入矩形窗函数,并在分析颗粒粒径与衍射光强导数最小值之间关系的基础上,确定矩形窗函数中心点位置及左右边界,利用该矩形窗函数对粒度分布进行截断处理,消除虚假峰,提高反演颗粒粒度分布的准确性.分别对两种标准颗粒进行了测量,并对不同算法的反演结果进行了对比.实验结果表明:引入矩形窗函数的改进Chin-Shifrin算法,能够有效排除粒度分布中的多假峰;粒度分布测量相对误差小于3%,重复性小于4%.     

生物组织的可见光与近红外光散射模型

对生物组织光学模型尤其是光散射特性进行了研究, 发现可以利用等效粒子数密度的粒度分布更精确地了解生物组织的光散射性质。在夫琅和费衍射近似下, 散射系数和散射相函数可以由等效粒子数密度的粒度分布得到。基于粒子粒度光散射测量技术, 所得结果可给出一种新的可行的测量生物组织光学性质参数的方法。     

基于Mie散射光强的多角度动态光散射复合角度加权方法

针对多角度动态光散射测量技术中通过Mie散射光强计算的角度权重估计方法存在信息利用率与抗噪性之间的矛盾,提出利用每一角度所有粒度的整体Mie散射空间特征进行角度加权和利用每一粒度对应Mie散射光的细节特征对核矩阵做元素加权的复合角度加权方法,并结合正则化方法进行了模拟和实测的多角度动态光散射数据反演.与采用光强比值法和光强均值法的反演结果比较表明,多角度动态光散射反演结果与角度加权方法密切相关.无噪声影响时,光强比值法和复合角度加权法都能得到准确的颗粒粒度分布,但光强均值法信息利用率不高;随着噪声水平的提高,光强比值法反演结果急剧变差,表现出较低的抗噪性能.复合角度加权方法通过兼顾信息利用率和抗噪性能,使得增加散射角时信息增多的优势得以更好地显现,并且有效地抑制了角度增多带来的噪声影响.该加权方法显著提高了多角度动态光散射进行颗粒测量,特别是对多峰分布颗粒体系测量的准确性.     

A Theoretical and Experimental Study of the Total Light Scattering Technique for particle size analysis

The total light scattering method for particle size measurement has a series of outstanding features, e.g. very simple instrumental arrangement, no serious requirements for its optical, photodetecting and electronic systems and its ease of use. Nevertheless, some problems still remain unsolved which should be dealt with to improve its further applications. An improvement has been made in this work. Comprehensive theoretical studies showed that this method is applicable to particle size analysis in the range 0.1–10 μm, i.e. for those particles whose diameter lies between the lower limit of the diffraction method and the upper limit of photon correlation spectroscopic (PCS) technique. Experimental studies with different monodisperse polystyrene latex spheres as standard reference material give good agreement with their nominal values.     

用于飞秒激光纳米加工的TiO_2粒子阵列诱导多种基底表面近场增强

利用纳米粒子辅助对飞秒激光能量进行空间局域化,使其在基底表面诱导产生纳米尺度的近场增强,这对超衍射极限微结构加工具有重要意义.目前对于粒子阵列诱导飞秒激光纳米孔加工的研究仅限于金属Au粒子及低折射率聚苯乙烯介电粒子等,本文提出并开展了应用高折射率TiO_2介电粒子阵列作为辅助诱导激光近场增强从而进行飞秒激光超衍射纳米孔加工的研究.对TiO_2介电粒子阵列在Si,Pt及SiO_2表面的近场强度分布进行了数值模拟,研究其基底表面近场增强的规律及物理过程.研究结果发现,使用硅基底时,阵列与单一TiO_2球形粒子相比其近场增强仅下降约30%;相对于入射激光强度而言,在直径约为100nm的空间范围内获得140倍的近场增强,这一现象可用于百纳米孔的激光加工.同时在其他典型基底的理论计算结果中也表明,几乎在所有金属及介电材料表面均可以实现良好的百纳米空间范围内的近场增强,并且具有近场随着基底折射率变大而增强的规律.这些现象的产生归因于TiO_2粒子中磁四极振荡产生的激光前向场增强及粒子与基底的耦合作用.进一步引入镜像电荷模型对基底光学参数对其表面近场增强的影响规律进行了分析和解释.本文的模拟结果对飞秒激光近场超衍射极限纳米加工的应用有着重要的意义.     

面向近原子尺度制造的光学测量精度极限分析

纳米级乃至更高精度的测量是原子及近原子尺度制造技术发展的基础和保障.光学测量具有精度高、测量范围广、测量直观等优点,其对单个成像光斑中心的定位可达远超衍射极限的精度.但由于光本身散粒噪声、探测器暗电流噪声等随机性的存在,光学测量存在精度极限.本文基于克拉美罗下界理论发展了可适用于任意强度分布像斑的精度极限计算方法,并以典型艾里斑为例,分析了成像过程中反映信噪比、能量集中度、计算方式的参数对定位精度极限的影响规律并给出提高精度的建议和结论.对实验所得像斑进行了精度极限计算,验证了所得结论对类似艾里斑的像斑的适用性.研究为原子及近原子尺度制造过程中光学测量的应用和优化提供了分析方法和理论指导.     

Theoretical analysis of stack gas emission velocity measurement by optical scintillation

Theoretical analysis for an online measurement of the stack gas flow velocity based on the optical scintillation method with a structure of two parallel optical paths is performed. The causes of optical scintillation in a stack are first introduced. Then, the principle of flow velocity measurement and its mathematical expression based on cross correlation of the optical scintillation are presented. The field test results show that the flow velocity measured by the proposed technique in this article is consistent with the value tested by the Pitot tube. It verifies the effectiveness of this method. Finally, by use of the structure function of logarithmic light intensity fluctuations, the theoretical explanation of optical scintillation spec- tral characteristic in low frequency is given. The analysis of the optical scintillation spectrum provides the basis for the measurement of the stack gas flow velocity and particle concentration simultaneously.     

利用消光起伏信号测量颗粒平均粒径

窄光束照射流动颗粒系时,透过率会产生起伏.起伏的透过率信号可用来测量颗粒平均粒径和浓度.由于在测量原理和结构上非常简单,这种方法可用来实现在线、实时测量.Gregory提出的数据处理模型要求光束直径较小而且远大于颗粒直径,本文提出一种新的模型,可在光束直径接近甚至小于颗粒直径情况下对透过率起伏信号进行处理,模拟分析和实验测试表明,该方法可得到较满意的测量结果.     

Particle sizing and velocity measurement of microspheres from the analysis of polarization of the scattered light

A brief review of the existing particle sizing methods is presented. An optical method under development is introduced from the analysis of the polarization ratio of the light scattered by the particles based on Lorenz-Mie theory. The theoretical background is summarized with the numerical calculation presented. A photogrammteric system has been set up to perform the measurements. Calibration of the experimental setup has been carried out on polystyrene microspheres of different size. The experimental values of the polarization ratio have been obtained by analyzing the particle images taken by the CCD to render the particle size under investigation. Several experiments and their results are demonstrated to illustrate the application fields of the optical method presented in the current study.     

Monte Carlo Simulations of Reflected Spectra Derived from Tissue Phantom with Double-Peak Particle Size Distribution

We made a tissue phantom with double-peak particle size distribution, which has polystyrene particles of cell nuclear size and mitochondrial size, and measured the spectrum from the tissue phantom using a single optical fiber. In this paper we investigate the characterization method for the tissue phantom with double-peak particle size distribution by comparing the measured spectra with the calculated ones using the Monte Carlo (MC) method. It is first shown that the Mie phase function characterizes better than the Henyey-Greenstein (H-G) phase function in MC calculation. Next, we compare the measurement spectra with those obtained by modeling as single-peak, conventional modeling for particle size distribution, and for double-peak particle size distribution. The single-peak modeling is found to cause considerable error for the tissue phantom with double-peak particle size distribution, which seems to simulate a biological tissue. We suggest that if one simulates the particle size distribution of a biological tissue by conventional modeling, the accuracy of estimation will be lower.     

差分吸收光谱仪测量上下限的确定

给出差分吸收光谱仪（DOAS）系统对测量上下限的确定方法,由于测量原理Beer-Lambert的线性适用范围限制了系统的测量上限,系统的噪声,被测气体的差分吸收截面以及测量的数据点数共同决定了系统的测量下限,通过理论分析与实际测量确定了DOAS系统的测量上下限。     

Multi-lognormal soot particle size distribution for time-resolved laser induced incandescence in diesel engines

In-cylinder and exhaust soot particle size measurements were carried out using time-resolved laser induced incandescence and electrical mobility spectrometer techniques in a single cylinder optical diesel engine and multi-cylinder high-speed diesel engine. The temporal decay of the laser induced incandescence signal from a polydisperse nanoparticle ensemble of soot during transient diesel combustion is shown to be described by both a single-lognormal distribution as well as multi-lognormal size distribution. However, a multi-lognormal particle size distribution is introduced in the existing model for a comprehensive characterisation and realistic reconstruction of the size distribution. Detailed theoretical analysis of multi-lognormal size distribution along with its application to the experimentally measured soot particle size is validated in this work. These results were also qualitatively compared and independently verified by the experimental results obtained by the electrical mobility spectrometer and published transmission electron microscopy data. These findings reveal that the in-cylinder and the exhaust soot particle size distributions in engines are better represented by a multi-lognormal size distribution.