LD泵浦环形单频Nd∶YVO4激光器的频率调谐特性研究

利用激光谐振腔内标准具的选模调谐特性和激光晶体自身的标准具作用 ,通过调节插入标准具和激光晶体的倾斜度及微调谐振腔长度 ,在 L D泵浦 Nd∶ YVO4 单频激光器上实现了精确调谐 ,最大可调谐范围约 1 0 0 GHz     

LD泵浦环形单频Nd：YVO4激光器的频率调谐特性研究

利用激光谐振腔内标准具的选模调谐特性和激光晶体自身的标准具作用,通过调节插入标准具和激光晶体的倾斜度及微调谐振腔长度,在LD泵浦Nd:YVO4单频激光器上实现了精确调谐,最大可调谐范围约100GHz。     

向列相液晶染料可调谐激光器的研究

对向列相液晶染料的可调谐激光器进行了光学特性研究. 以650 nm为中 心波长设计了SiO₂和TiO₂多层膜的一维光子晶体, 以激光染料与向列相液晶的混合物作为增益介质层, 制备了波长可调谐激光器.用Nd: YAG倍频脉冲激光器输出的532 nm激光抽运所制备的激光器样品得出如下光学特性: 激光发射波长随温度调谐范围为605.5---639.8 nm, 达到34.3 nm, 随电压调谐范围为634.5---619.5 nm, 达到15 nm. 发射激光每脉冲的阈值能量为12.3 μJ, 激光线宽小于1 nm.     

420mW全固态连续单频可调谐1542nm激光器

设计并研制了一台激光二极管端面泵浦的全固态连续单频可调谐1 542nm激光器。通过设计谐振腔的镀膜参数调控Er,Yb:YAB激光器的增益谱,实现了1 542nm波段的激光振荡。在此基础上,通过优化激光晶体的厚度和谐振腔的输出耦合镜透射率等参数,并利用扭摆模腔选择单纵模技术,获得了最大输出功率为420mW的连续单频1 541.9nm激光运转。输出激光在3小时内的功率稳定性优于±3%,激光强度噪声在分析频率3 MHz处即达到散粒噪声极限。通过内腔电光晶体和电光标准具调控谐振腔的腔长,实现了激光器在1 541.959nm～1 542.014nm的波长范围内的准连续波长调谐。     

全固态单纵模脉冲Nd:YVO_4环形激光器

设计并研制了全固态调Q脉冲单纵模Nd:YVO4环形激光器。利用880nm激光二极管端面抽运Nd:YVO4晶体,通过四镜环形谐振腔中插入声光调Q晶体、标准具,并优化激光谐振腔的结构,获得了重复频率为200Hz、脉宽为26.6ns的单纵模脉冲1.064μm激光输出。当泵浦功率为15 W时,单纵模激光输出的单脉冲能量为570μJ、脉冲能量稳定性优于3%。     

二极管泵浦全固态589 nm脉冲激光器

 报道了一台二极管激光器(DL)泵浦的全固态Nd:YAG和频激光器,激光是由Nd:YAG晶体的1 064 nm 和1 319 nm 谱线外腔和频产生,以6 mm×6 mm×12 mm KTP为和频晶体,采用Ⅱ类临界相位匹配, 在400 Hz重复频率下,当分别注入3.05 W和2.46 W的1 064 nm和1 319 nm调Q脉冲到KTP晶体时,和频最大输出达到了1.3 W,脉宽为35 ns,线宽优于3 GHz,和频效率达到了23.5％, 光束质量因子分别为1.84和1.93。实验结果表明采用激光二极管阵列泵浦Nd:YAG/ KTP 腔外和频技术是获得黄激光的高效方法, 并通过精确控制谐振腔内标准具的倾角与温度,和频输出波长可精确调谐到Na D2线。     

电光晶体调谐的外腔反馈半导体激光器

报道一种用电光晶体实现快速调谐和凋制激光频率的方法.在Littrow型外腔反馈半导体激光中插入LiNbO3晶体,利用LiNbO3晶体的电光效应,通过改变晶体电压来调节激光器的有效腔长,可以对激光频率进行快速的调谐和调制.采用该方法,自制外腔反馈半导体激光器的调谐频率可达到2 kHz,它的调谐范围为350 MHz,激光频率调谐系数约为1.06 MHz/V,用饱和吸收光谱观测频率调谐的效果.快速激光频率调制可以应用在稳频技术上,将外腔反馈半导体激光器调制在5～100 kHz频率下,均获得了87Rb原子D2线的饱和吸收光谱的色散信号,并实现了激光频率在饱和吸收峰上的长期稳定.     

LD泵浦Nd:YAG/LBO结构660 nm红光激光器

采用国产LD泵浦Nd:YAG晶体,通过谐振腔镜的膜系选择获得了Nd³⁺离子中波长为1319 nm的受激辐射振荡,首次用I类临界位相匹配LBO进行腔内倍频,实现了660 nm红色激光的高效倍频输出.当泵浦注入功率为800 mW时,660 nm激光基横模(TEM₀₀)输出功率为46 mW,光光转换效率高达5.75%.     

扭转模结构双腔双频Nd∶YAG激光器

为了产生频差可调谐1 064nm双频激光输出,设计了一种扭转模结构双腔双频Nd∶YAG激光器,其两个驻波谐振腔共用相同的Nd∶YAG增益介质,以扭转模结构消弱增益空间烧孔效应,使Nd∶YAG激光器的两个驻波腔均以单纵模振荡,从而获得正交线偏振1 064nm双频激光输出.理论分析了扭转模结构激光单纵模选择原理和双频激光同时振荡原理,实验研究了双频激光振荡特性和频差调谐特性.研究结果表明:双频Nd∶YAG激光器的两个谐振腔能够同时以线偏振单纵模稳定振荡输出,其频差大小可随激光腔长的改变而调谐,频差调谐范围可达1个纵模间隔,实验观察到的频差调谐范围为0.3GHz~3GHz.     

全固态紫外激光器研究

本文报道了具有增强谐振倍频腔的全固态紫外激光器研究半导体激光二极管(LD)泵浦的Nd:YVO₄激光晶体产生波长为1064nm的近红外光,腔内倍频输出波长为532nm的绿光,再送入增强谐振腔进行四倍频,输出波长为266nm的深紫外激光产生深紫外激光的基频绿光输入阈值可低到2.5mW据我们所知,这是国内首次报道的全固态紫外激光器.     

Single longitudinal mode pulse from a TEA CO<Subscript>2</Subscript> laser by using a three-mirror resonator with a Fabry–Pérot etalon

We present a single longitudinal mode (SLM) TEA CO₂ laser oscillation by using a three-mirror resonator with a Fabry–Pérot etalon. The etalon was inserted in the optical path taken out from the main resonator of the CO₂ laser for protecting the etalon from damage on the surface. A modified numerical model of the three- mirror resonator was investigated for design the laser. SLM pulse from the TEA CO₂ laser was achieved, and the experimentally measure values were found to have good agreement with the numerical model. The maximum pulse energy of reliable SLM emission is obtained in excess of 200 mJ at 9.57 μm. The reliability of producing SLM pulses was higher than 90%, and there was no damage on the etalon PACS  42.55.Lt; 42.60.Fc     

激光二极管抽运频差可调谐双频固体激光器的研究

研究了激光二极管抽运的可调频差的双频固体激光器，激光增益介质为2mm厚的1at%掺杂Nd:YAG薄片.对谐振腔产生稳定双频激光的条件作了分析，用琼斯矩阵计算了谐振腔内各处电场矢量的偏振态，证明了双频激光两个电场矢量偏振态之间总是正交的.两个偏振激光频率间隔由改变λ/4波片快轴之间的夹角实现调谐.实验中使用腔内标准具实现单频运转，然后插入双λ/4波片使单纵模激光频率分裂，实现了激光器的双频输出.实验中得到双频激光稳定运转时频差的上限约为1.3GHz；由于强模竞争现象的存在，实验中所观察到的频差下限为50MHz. 100MHz拍频时得到的双频激光输出功率为85mW. 关键词： 激光技术 固体激光器 双频激光     

多纵模激光F-P标准具双边缘测风可行性分析

讨论采用多纵模激光器作探测光源用于双边缘多普勒激光雷达测风的可行性。给出了多纵模激光器谐振腔腔长与边缘滤波器F-P标准具腔长之间的关系。分析了多纵模双边缘测风的主要特性,计算灵敏度、信噪比和径向测速误差,并与单纵模测风性能进行对比。可用类似单纵模测风中动态频率跟踪技术解决多纵模激光器频率漂移问题。     

A stable submillimeter laser local oscillator for heterodyne radiometry and spectroscopy

A submillimeter laser with off-axis pump beam injection is described. This design concept achieves complete isolation of the pump laser with respect to the pump radiation reflected from the smm resonator. Active line independent stabilization of the pump laser is obtained by the use of an external tunable etalon as a frequency reference. The smm output power is constant to within 4% over periods of hours. Mean frequency drifts of less than 2 parts in 10⁸ per minute were measured by mixing with very high harmonics of an X-band synthesizer in a planar Schottky diode.Supported in part by NSF     

60 W yellow laser at 561 nm by intracavity frequency doubling of a diode-pumped Q-switched Nd:YAG laser

A high-power yellow laser was achieved by intracavity frequency doubling of a diode-pumped Nd:YAG rod laser. A solid etalon was inserted into the resonator to implement efficient operation of the low-gain single line at 1123 nm transition. By using a LBO crystal inside the cavity as the frequency doubler, the maximum output power of the 561 nm yellow laser was obtained to be as high as 60.3 W with a pulse repetition frequency of 6 kHz, corresponding to an optical-to-optical conversion efficiency of about 6.1%. The output power fluctuation of the yellow laser was measured to be better than 3% in half an hour.     

Laser mode selection in reflective multipass optical cavity

The performance of a simple resonator that couples a reflective multipass interferometer cavity and a Fabry-Pérot etalon to obtain high efficiency tunable single-longitudinal mode (SLM) oscillation in a TEA CO₂ laser is reported. A numerical model of the resonator was explained to predict the mode behavior of the laser as well as to optimize the resonator to achieve SLM operation, and the predicted mode characters are experimentally verified.     

Effect of an internal Fabry-Pérot etalon on the modes of a resonator

The effect of an internal Fabry-Pérot etalon on the modes of a resonator has been calculated. It is found that the modes are pulled towards the peak of the etalon transmission and are no longer equidistant. This has been verified by observing the modes of a N₂ laser pumped dye laser.     

Single mode oscillation of TEA CO2 laser with an interference resonator

An effective single-longitudinal mode (SLM) pulse TEA CO₂ laser operation was demonstrated using a Michelson’s type resonator with a tilting Fabry-Perot etalon. A modified numerical model of the interference resonator was investigated for designing the laser. The experimentally measured values were found to have good agreement with the numerical model. A pulse width of about 90 ns and the maximum pulse energy of about 300 mJ were achieved at 10.59 μm in SLM and TEM₀₀ mode. The reliability of producing SLM pulses was 100% and there was no damage on the etalon. By turning the interference resonator, the SLM output was tuned 44 lines of the CO₂ spectrum.     

Multiplication of spectral lines generated by two-color stimulated raman effect

A dye laser emitting at four different frequencies separated by 293.5 (=587/2) cm^-1 is made by inserting an etalon in the resonator cavity of the laser. This laser beam is focused into molecular hydrogen (rotational Raman shift frequency, 587 cm^-1) to generate a multicolor laser beam consisting of more than 10 rotational lines in the vicinity of the fundamental lines by four-wave Raman mixing. Such rotational lines also occur in the vicinity of the vibrational Raman lines. Thus more than 25 emission lines appear simultaneously. This approach is useful to multiply the line density, i.e., the emission lines within a specified wavelength region.