Synthesis,phase stability and oxide ion conductivity of Ce(IV)–Cd(II) double substituted bismuth vanadate

Bi₄V₂O_11-δ has been doped with Ce and Cd to study double substitution. The system with various dopant concentrations (0.07 ≤ x ≤ 0.30) was prepared by the standard solid-state reaction method. The correlation between the polymorphism and oxide ion performance was well investigated as a function of temperature and composition with the help of thermal analysis, X-ray diffraction (XRD) and AC impedance spectroscopy. From XRD results it is seen that the high oxide ion conducting tetragonal γ-phase is stabilized for x = 0.17. For the compositions x ≤ 0.10, monoclinic α-phase is retained at room temperature with clear evidence for two successive phase transitions α ? β and β ? γ. For x = 0.13, β ? γ phase transition is seen. However, the existence of order–disorder, γ' ? γ transition was confirmed for x = 0.17. It is seen that the highest low-temperature ionic conductivity at 320 °C is 3.19 × 10^?4 S cm^?1 which was observed for x = 0.17.     

Study on electrical conductivity and phase transition in singly doped BIPBVOX (Bi2V1−xPbxO5.5−x/2) solid electrolyte

Samples of bismuth lead vanadium oxide (BIPBVOX) (Bi₂V_1–xPb_xO_5.5–x/2) singly substituted system in the composition range 0.05 ≤ x ≤ 0.20 were prepared by sol–gel synthesis route. Structural investigations were carried out by using a combination of differential thermal analysis (DTA) and powder X-ray diffraction (PXRD) technique. Energy dispersive X-ray spectroscopy analysis (EDXA) of doped samples was carried out to predict the sample purity and doping concentration. Transitions, α?β, β?γ and γ′?γ were detected by XRD, DTA and variation in the Arrhenius plots of conductivity. The ionic conductivity was measured by AC impedance spectroscopy. The solid solutions with composition x ≤ 0.07 undergo α?β phase transition, at 329 °C and β?γ phase transition at 419 °C. The highly conducting γ′-phase was effectively stabilized at room temperature for compositions with x ≥ 0.17 whose thermal stability increases with Pb content. At 300 °C, the highest value of conductivity 6.234 × 10^?5 S cm^?1 was obtained for composition x = 0.15 and at 600 °C the highest value of conductivity 0.65 S cm^?1 is observed for x = 0.17. AC impedance plots reveal that the conductivity is mainly due to the grain contribution to oxide ion conductivity.     

Correlation between phase structure and electrical conduction in BISNVOX system for intermediate temperature solid oxide fuel cells (IT-SOFC)

Samples of Sn⁴⁺-substituted bismuth vanadate, formulated as Bi₄Sn _x V_{2? x} O_{11?( x /2)? δ} in the composition range 0.07 ≤ x ≤ 0.30, were prepared by standard solid-state reactions. Sample characterization and the principal phase transitions (α ? β, β ? γ and γ′ ? γ) were investigated by FT-IR spectroscopy, X-ray powder diffraction, differential thermal analysis (DTA) and AC impedance spectroscopy. For composition x = 0.07, the α ? β and β ? γ phase transitions were observed at temperatures of 451 and 536°C, respectively. DTA thermograms and Arrhenius plots of conductivities revealed the γ′ ? γ phase transition at 411 and 423°C for x = 0.20 and 0.30, respectively. AC impedance plots showed that conductivity is mainly due to the grain contribution, which is evident in the enhanced short-range diffusion of oxide ion vacancy in the grains with increasing temperature. The highest ionic conductivity (5.03 × 10^?5 S cm^?1 at 300°C) was observed for the x = 0.17 solid solution with less pronounced thermal hysteresis.     

Study on phase stabilization and electrical performance of BICO0.20−xNIxVOX solid electrolyte

BICO_0.20?xNI_xVOX solid electrolyte in the composition range 0 ≤ x ≤ 0.20 was synthesized by standard solid-state reactions. The influence of Ni substitution for Co on the relationship between the phase stabilization and electrical performance was investigated by means of X-ray powder diffraction (XRPD), differential thermal analysis (DTA) and AC impedance spectroscopy. The highly conductive γ′-phase was effectively stabilized at room temperature for compositions with x ≥ 0.13 whose thermal stability increases with Ni content. On the other hand, complex plane plots of impedance suggested a major contribution of polycrystalline grain interiors to the overall electrical conductivity and the fastest oxygen-vacancy diffusion in the perovskite vanadate layers at x = 0.13. The dielectric permittivity measurements revealed the fact that suppression of the ferroelectric transition is compositionally dependent. However, a maximum ionic conductivity at lower temperatures (～2.56 × 10^?4 S cm^?1 at 300 °C) was observed for the composition with x = 0.13.     

Effect of Cu–Al double substitution on the electrical properties of Bi4V2O11

Bi₂Cu_0.1?xAl_xV_0.9O_5.35?x/2?δ, 0.02 ≤ x ≤ 0.08, were synthesized by standard solid-state reaction route. Structural and electrical properties of samples are characterized by X-ray diffraction (XRD), differential thermal analysis (DTA), Fourier transform infrared (FT-IR) and alternating current (AC) impedance spectroscopy. The tetragonal γ′ phase structure is preserved to room temperature with compound x = 0.02. The stabilization of β orthorhombic phase is observed for compositions 0.04 ≤ x ≤ 0.05. As the Al content increases, the monoclinic α phase is evidenced for materials 0.06 ≤ x ≤ 0.08. The electrical investigation of Bi₂Cu_0.1?xAl_xV_0.9O_5.35?x/2?δ system has been performed in the frequency range from 20 Hz to 1 MHz using AC impedance spectroscopy. The impedance spectra indicate the two semicircle arcs associated with the bulk and grain boundary resistances at temperature below ～450 ^○C. The conductivity generally changes when Al is substituted. The highest conductivity at 300 ^○C (σ = 2.55 × 10^?4 S cm^?1) is shown for x = 0.02.     

Effect of Zn–Ti double substitution on the electrical properties of Bi4V2O11

New samples of the Bi₂Zn_0.1–xTi_xV_0.9O_5.35+x; 0.02 ≤ x ≤ 0.08 system have been synthesized through a standard solid-state reaction route. XRD analysis and differential thermal analysis have been used to characterize the phase structure of samples. The γ′ phase is stabilized to room temperature in all investigated samples. The electrical properties of the BIZNTIVOX system have been studied by using AC impedance spectroscopy. An AC impedance response as a function of frequency (20 Hz–1 MHz) has been used to investigate the electrical conductivity and the dielectric permittivity in the temperature range of 150 °C–700 °C. In this temperature range, the phase transition γ′ to γ has been observed in all the compositions studied. AC impedance spectroscopy indicates that the resistance of samples decreases with increase of temperature. The ionic conductivity of samples appeared as a two-line region in Arrhenius dependence. At 300 °C, the highest ionic conductivity is shown by the composition x = 0.05 (σ₃₀₀ = 1.35 × 10^?4 S cm^?1).     

Effect of Zn substitution on the electrical properties of Bi2Co0.1V0.9O5.35 synthesized by sol-gel method

Samples of Bi₂V_0.9Co_0.1-xZn_xO_5.35, 0.02 ≤ x ≤ 0.08 with layered Aurivillius structure were synthesized successfully by sol-gel citrate method. Structural and electrical characterization of compositions has been investigated by X-ray diffraction, thermogravimetric analysis–differential scanning calorimetric (TGA–DSC) analysis and AC impedance spectroscopy. The tetragonal γ phase has been observed for all investigated samples. The AC impedance response of samples has been measured in the frequency range of 20 Hz to 1 MHz. The impedance for pellets decreases as thermal energy increases. The contribution of grain to the conduction process is more than that of grain boundary. The ionic conductivity and dielectric permittivity are found to be composition-dependent and increase with increasing Zn concentration. The maximum electrical conductivity observed for the composition x = 0.08 is σ = 4.51 × 10^?4 S cm^?1 at 300 °C.     

Effect of Ni(II) substitution on phase stabilization electrical properties of BICo(III)VOX.20 oxide-ion conductor

The BICO_0.20–xNI_xVOX solid electrolyte was synthesized by the standard solid-state reaction. The effect of Ni(II) substitution for Co(III) on phase stabilization and oxide-ion performance has been investigated in the compositional range 0?≤?x?≤?0.20 using X-ray powder diffraction, differential thermal analysis and AC impedance spectroscopy. The highly conductive γ′-phase was effectively stabilized at room temperature for compositions with x?≥?0.13 whose thermal stability increases with Ni content. The complex plane plots of impedance were typically represented at temperatures below 380?°C, suggesting a major contribution of polycrystalline grains to the overall electrical conductivity. The dielectric permittivity measurements revealed the fact that suppression of the ferroelectric transition is compositionally dependent. Interestingly, the maximum ionic conductivity at lower temperatures (~2.56?×?10^?4?S^?cm^?1 at 300?°C) was observed for the composition with x?=?0.13. The variation of low-temperature conductivity with Ni content was accompanied with a general drop in the corresponding values of ΔE_LT. However, the local minimum high-temperature conductivity, σ₆₀₀?°C?~?2.26?×?10^?2?S^?cm^?1 for x?=?0.10, coupled with a local maximum value of ΔE_HT?~?0.48?eV was attributed to an increased defect trapping effect correlated with the V(V)?→?V(IV) reduction at elevated temperatures.     

CO(III)–NI(II) double substituted bismuth vanadate: synthesis,phase stabilization,and structural and electrical characterization

Samples of Co–Ni double substituted bismuth vanadate, BICO_0.20?x NI _x VOX (Bi₄Co_0.20???x ^(III)Ni _x ^(II)V_1.8O_{10.8???(x/2)???δ} ;0?≤?x?≤?0.20) were synthesized by standard solid state reactions. The influence of Ni substitution for Co on phase stabilization and oxide-ion performance have been investigated using X-ray powder diffraction, differential thermal analysis, and AC impedance spectroscopy. The high conducting γ′-phase was effectively stabilized at room temperature for compositions with x?≥?0.13 whose thermal stability increases with Ni content. The complex plane plots of impedance were typically represented at temperatures below 380 °C, suggesting a major contribution of polycrystalline grains to the overall electrical conductivity. The dielectric permittivity measurements revealed the fact that suppression of the ferroelectric transition is compositionally dependent. Interestingly, the maximum ionic conductivity at lower temperatures (～2.56?×?10^?4 S cm^?1 at 300 °C) was observed for the composition with x?=?0.13. However, a good agreement was generally found between the values of electrical conductivity and corresponding activation energies of conduction.     

Study on phase stability and oxide ion conductivity in the BIAGVOX system

A novel oxide ion conductor, BIAGVOX formulated as Bi₄Ag_xV_2?xO_11?(2x)?δ is obtained by substituting a fraction (x) of V⁵⁺ by Ag⁺ in Bi₄V₂O₁₁ samples of the BIAGVOX system in the composition range, 0.05≤x≤0.30 were synthesized using the standard solid-state reaction. XRPD, FT-IR, DTA and AC impedance spectroscopy were used for the investigation of the correlation between the structural phase stability and oxide ion performance of the BIAGVOX materials. It has been found that orthorhombic, β, and incommensurate tetragonal, γ′ were stabilized at room temperature for compositions with x≤0.15 and x≥0.20, respectively. The enthalpy of β→γ and γ→γ transition exhibited a general drop with increasing Ag content and a minimum transition temperature was observed for x=0.20. However, the oxide ion conductivity at lower temperatures remarkably increased in composition stability ranges of β- and γ-phase, while a maximum conductivity was reported for the high temperature γ-phase at x=0.15. However, the low temperature conductivity, σ₃₀₀°c measured for x=0.30 was found to be comparable with the maximum ionic conductivity of the BICUVOX system reported for x=0.20 at the same temperature.     

Effect of iron doping at Mn-site on complex impedance spectroscopy properties of Nd0.67Ba0.33MnO3 perovskite

The effect of Fe-doping at Mn-site on the structural and electrical properties of Nd_0.67Ba_0.33Mn_1?xFe_xO₃ (0 ≤ x ≤ 0.05) perovskites has been investigated. X-ray diffraction patterns show that the structural parameters change slightly due to the fact that the Fe³⁺ ions replacing the Mn³⁺ have similar ionic radius. The electrical properties of these samples have been investigated using complex impedance spectroscopy technique. a function of the frequency at different temperatures. When increasing the Fe-content, a decrease of dc conductivity was observed throughout the whole explored temperature range and the deduced activation energy values are found to increase from 128 meV for x = 0 to 166 meV for x = 0.05. The curves of the imaginary part of impedance (Z″) show the presence of relaxation phenomenon in our samples. The complex impedance spectra show semicircle arcs at different temperatures and an equivalent circuit of the type of R_g + (R_gb//C_gb) has been proposed to explain the impedance results.     

Electrical conductivity and dielectric relaxation behavior of AgFeP2O7 compound

In the present study, AgFeP₂O₇ was prepared by a solid-state reaction method. Rietveld refinement of the X-ray diffraction pattern suggests the formation of the single phase desired compound with monoclinic structure at room temperature. Not only were the impedance spectroscopy measurements of our compound carried out from 209 Hz to 5 MHz over the temperature range of 553 K–698 K but its AC conductivity as well as the dielectric relaxation were evaluated. Impedance measurements show AgFeP₂O₇ an ionic conductor being the conductivity 1.04?×?10^–?5(Ω^–?1cm^–?1) at 573 K. The conductivity and modulus formalisms provide nearly the same activation energies for electrical relaxation of mobile ions revealing that transport properties in this material appear to be due to an ionic hopping mechanism dominated by the motion of the Ag⁺ ions along tunnels presented in the structure of the investigated material.     

The determination of Li+ mobility in solid electrolyte Li1.3Al0.1Zn0.1Ti1.8P3O12 in view of ionic diffusivity and conductivity

Nasicon-type solid electrolyte Li_1.3Al_0.1Zn_0.1Ti_1.8P₃O₁₂ was prepared by citric acid-assisted acrylamide polymerisation gel method. X-ray diffraction pattern showed that the introduction of Zn²⁺ in the parent matrix Li_1+x Al _x Ti_2?x P₃O₁₂ made it easier to get high-purity rhombohedral structure (space group $ R\overline 3 C $ ) Li_1.3Al_0.1Zn_0.1Ti_1.8P₃O₁₂ without the evidence of impurity secondary phase. The Li⁺ kinetics were investigated by complex impedance in bulk pellet and ionic conductivity in battery-type composite cathode, respectively. Grain-interior resistance measured by galvanostatic intermittent titration technique, potential step chronoamperometry, and AC impedance spectroscopy at 20 °C varies in the range 1.2–1.95?×?10^?4?S?cm^?1, which is in good agreement with that obtained by complex impedance method 1.5?×?10^?4?S?cm^?1.     

Ionic conductivity and structural properties of MnO-doped Bi4V2O11 system

Bi₄V₂O₁₁ exists in three phases viz. α, β, and γ. High temperature γ-phase can be stabilized to room temperature owing to its higher conductivity by the partial substitution of metallic cations for vanadium in Bi₄V₂O₁₁. Phase transitions from α → β and β → γ are composition and temperature-dependent. Mn²⁺-doped compounds Bi₄V_2−x Mn _x O_{11− δ} (0 ≤ x ≤ 0.4) have been synthesized by solid state reaction technique and investigated by X-ray diffraction and ionic conductivity measurement. High ionic conducting γ-phase is stabilized for x ≥ 0.2. The ionic conductivity of the series of Bi₄V_2−x Mn _x O_{11− δ} samples has been measured by using ac impedance spectroscopy technique. The conductivity data do show departure from its simple Arrhenius behavior for all of the compositions. The highest conductivity observed for x = 0.2 sample can be attributed to lower activation energy.     

Investigation on (EC/DMC)(70−x)wt% to LiBETI(x)wt% impact on PVdF-co-HFP/octadecylamine-MMT(montmorillonite) nano clay composite electrolytes

The composition dependence of plasticizer (ethylenecarbonate(EC)/dimethyl carbonate(DMC))_(70?x)wt% to Lithium bis(perfluoroethanesulfonyl)imide(LIBETI)_(x)wt% salt (where x?=?1.5, 3.0, 4.5, 6.0 wt%) on PVdF-co-HFP (25 wt%)/surface modified octadecylamine containing montmorrillonite (ODA-MMT) nano clay (5 wt%) matrix has been investigated by AC impedance, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dielectric and cyclic voltammetry studies. The enhanced conductivity 2.1?×?10^?5 Scm^?1 is noted in salt rich phase (EC/DMC)_(70–6)wt% /LiBETI_(x=6)wt% (VK4). In XRD, 2θ at 20.9° confirms β-phase. In FTIR studies, vibrational bands 838, 522 and 611 cm^?1 confirm β-phase of PVdF due to clay intercalation. In DSC studies, the melting of α-phase crystallites is noted between 140–150 °C. In SEM studies, one of the membranes presents fern leaf texture confirming swelling of clay. The increase in dielectric constant and dielectric loss with decrease in frequency is attributed to high contribution of charge accumulation at the electrode–electrolyte interface. In cyclic voltammetry studies, salt-rich phase membrane (VK4) shows good cyclability than other membranes.     

PVA-assisted synthesis and characterization of nano-crystalline La3+ and Mg2+ co-doped CeO2 electrolyte for intermediate-temperature solid oxide fuel cells

A series of nano-crystalline ceria-based solid solution electrolyte, Ce_0.8La_0.2?x Mg_xO_2?δ (x?=?0.0, 0.05, 0.10, 0.15, and 0.2), were synthesized via the polyvinyl alcohol (PVA) assisted combustion method, and then characterized to the crystalline structure, powder morphology, sintering micro-structure, and electrical properties. Present study showed that Ce_0.8La_0.2?x Mg _x O_2?δ was exceedingly stable as a cubic phase in all temperature range and exhibited fine crystals ranging from 15 to 20 nm. After sintering at 1,400 °C, the as-prepared pellets exhibited a dense micro-structure with 96 % of theoretical density. The electrical conductivity was studied using AC impedance spectroscopy and it was observed that the composition Ce_0.8La_0.1?Mg_0.1O_2?δ showed higher electrical conductivity of 0.020 S?cm^?1 at 700 °C. The thermal expansion was measured using dilatometer technique in the temperature range 30–1,000 °C. The average thermal expansion coefficient of Ce_0.8La_0.1?Mg_0.1O_2?δ was 12.37?×?10^?6 K^?1, which was higher than that of the commonly used SOFC electrolyte YSZ (~10.8?×?10^?6 K^?1).     

Structural and electrical properties of hexavalent-substituted BIMEVOX synthesized by a microwave-assisted route

The microwave (MW)-assisted solid synthesis route was employed to prepare a new Aurivillius-type compound with the general formula Bi₂Cr _x V_1?x O_5.5+x?δ; 0≤x≤0.20 (BICRVOX). This novel synthesis method revealed that polycrystalline products of the BICRVOX system can effectively be obtained after being irradiated for 25 min rather than for the many hours of high-temperature heating needed in other conventional routes. The phase structure of MW-prepared samples was characterized by comparison with those obtained from the conventional solid-state reaction, using powder X-ray diffraction, FT-IR and differential thermal analysis techniques. Importantly, the substitution of Cr(VI) for V(V) in the parent compound resulted in stabilization of only the α - and β -phases. AC impedance spectroscopy confirmed that the MW-prepared samples possess slightly lower oxide-ion performance compared with the conventionally-prepared ones; it did, however, evidence the significant role of powerful dielectric heating of MWs in lowering the charge carrier accumulation.     

Ionic conductivity of Zr1−xIn2xO2−x

As x in Zr(In)O_2?x is increased from 0.08 to 0.16 (9–19 mole per cent In₂O₃) the activation energy E(x) for ionic conduction increases from 1.05 to 1.51 eV; the concuctivity decreases from 2 × 10^?5 to 3 × 10^?6Ω^?1cm^?1at 400°C, is composition-independent at about 580°C, and increases from 1 × 10^?2 to 4 × 10^?2Ω^?1cm^?1 at 800°C. The pre-exponential term of the Boltzmann-type conductivity equation depends exponentially on E(x), a much stronger dependence on x than theoretically expected with a model for ionic conductivity that includes nearest-neighbor defect interactions. Analysis of reported conductivity data for Zr(M)O_2?x (M = Sc, Y, Ca and rare earth metals) and other doped oxide electrolytes with fluorite-type structure reveals that the same relationship is observed with these materials when x γ0.08. It is shown that ionic conduction in these oxides is consistent with nearest neighbor vacancy-cation defect interaction forx < 0.08 but that an additional complex interaction with composition-dependent free energy ΔG(x) occurs when xγ 0.08.The lattice constant of Zr(In)O_2?x with the cubic fluorite-type structure is independent of composition, 5.114 ± 0.002 Å, in agreement with ionic size considerations.     

Effect of Sn-doping at Mo-site on the conductivity of La2Mo2O9 series of compounds

Taking oxygen ion conductor La₂Mo₂O₉, as a base compound, a series of Sn-doped La₂Mo_2−x Sn _x O_9−δ, x = 0, 0.01, 0.02, 0.03, 0.05, 0.1, 0.15, 0.2 specimens were prepared and characterized by XRD for phase and crystal structure determination and ac impedance spectroscopy for ac and dc conductivity measurement. We have found that there is slight improvement in overall conductivity of the specimen with x = 0.03 at 800°C compared to the undoped compound at the same temperature. The value of conductivity when extrapolated to 800°C is found to be 0.055 S cm-1 for the specimen with x = 0.03, whereas conductivity of undoped specimen at the same temperature is found to be 0.033 Scm⁻¹.