α-Sexithiophene on Cu(1 1 0) and Cu(1 1 0)-(2 × 1)O: An STM and NEXAFS study

The adsorption of α-sexithiophene (6T) on Cu(1 1 0), Cu(1 1 0)-(2 × 1)O and the mesoscopically patterned Cu-O striped surface have been studied by STM (scanning tunnelling microscopy), XPS (X-ray photoelectron spectroscopy) and NEXAFS (near edge X-ray absorption fine structure). The molecular resolution of the STM allowed to determine the orientation and local order of the molecules in the submonolayer and monolayer regime. It is shown that the 6T molecules align with their long molecular axis along the densely packed copper rows on Cu(1 1 0) and along the Cu-O rows on the Cu(1 1 0)-(2 × 1)O surface. On the striped phase with alternating copper and Cu-O regions the molecules adsorb first on the Cu regions and after complete filling of these regions, on the Cu-O. The orientation is the same on both areas as on the respective pristine surfaces with the only exception that the molecules reorient by 90° if the width of the copper regions is smaller than the molecular length. The NEXAFS measurements allowed for a determination of the adsorption geometry of the molecules: while 6T lies flat on the surface on clean copper, the molecular planes are inclined with an angle as high as 39° with respect to the substrate on (2 × 1)O. For the latter, this inclination angle is 4° higher than in the bulk crystal structure of 6T observed for thicker films to release stress and allow commensurability with the substrate lattice, while for the former it is a result of the aromatic system bonding to the Cu(1 1 0) surface, as confirmed by XPS.     

Indentation studies on 〈1 0 0〉, 〈0 0 1〉 and 〈1 0 1〉 face of ammonium dihydrogen phosphate (ADP) single crystals: A novel nonlinear optical material

In the present work, Vickers microhardness measurements were carried out on different faces i.e. (1 0 0), (0 0 1) and (1 0 1) of ammonium dihydrogen phosphate (ADP) single crystals grown by slow evaporation solution technique at room temperature in the load ranging from 0.2 to 2 N. The obtained results show that the load independent hardness values are 0.8, 0.7 and 0.66 GPa, respectively at different faces of ADP crystal. From the crack length measurements, the fracture toughness values (K_c) was estimated using Evans and Anstis model and the present studies suggest that Evans model is more relevant when compared to Anstis model. The load variation of some mechanical properties viz. brittle index number (B_i) and yield strength (σ_y) for ADP have also been calculated for the first time.     

Phase coexistence between the (√3 × √3)R30° - β and (1 × 1) phases on Pb/Ge(1 1 1)

We have characterized the phase transition between the (1 × 1) and (√3 × √3)R30° - β phases on Pb/Ge(1 1 1) using low energy electron microscopy (LEEM). We show that the transition is first-order and that, in the coexistence region of the two phases, the dominant mechanism for phase separation changes critically with Pb coverage, from nucleation and growth at 1.33 ML (saturation coverage of the β phase) to spontaneous domain switching due to thermal fluctuations of the local Pb density for slightly smaller coverage. As the Pb coverage decreases, the concentration of vacancies in the β phase increases, making additional possible Pb adsorption sites available. The larger resulting local density fluctuation of Pb becomes comparable to the density difference of the two phases, manifesting itself in the observed domain switching.     

Adsorption and decomposition of γ-butyrolactone on Pd(1 1 1) and Pt(1 1 1)

The adsorption and thermal chemistry of γ-butyrolactone (GBL) on the (1 1 1) surface of Pd and Pt has been investigated using a combination of high resolution electron energy loss spectroscopy (HREELS) and temperature programmed desorption (TPD). HREELS results indicate that GBL adsorbs at 160 K on both surfaces through its oxygenate functionality. On Pd(1 1 1), adsorbed GBL undergoes ring-opening and decarbonylation by 273 K to produce adsorbed CO and surface hydrocarbon species. On Pt(1 1 1), very little dissociation is observed using HREELS, with almost all of the GBL simply desorbing. TPD results are consistent with decarbonylation and subsequent dehydrogenation reactions on Pd(1 1 1), although small amounts of CO₂ are also detected. TPD results from Pt(1 1 1) indicate that a small proportion of adsorbed GBL (perhaps on defect sites) does undergo ring-opening to produce CO, CO₂, and H₂. These results suggest that the primary dissociation pathway for GBL on Pd(1 1 1) is through O-C scission at the carbonyl position. Through comparisons with previously published studies of cyclic oxygenates, these results also demonstrate how ring strain and functionality affect the ring-opening rate and mechanism.     

Influence of cold-rolling texture and heating rate on {1 1 0}〈0 0 1〉 development in inhibitor-free 3%Si–Fe sheets

This paper presents cold-rolling and annealing methods to obtain a high-magnetic induction in inhibitor-free 0.1-mm-thick 3% silicon–iron sheets containing 18 or 150 ppm sulfur. In case of the two-step cold-rolling, the sheets containing 150 ppm sulfur showed a strong {1 0 0} final texture at 400 °C/h, and some fraction of {1 1 0} component was observed at 25 °C/h. However, three-step cold-rolling resulted in a sharp {1 1 0}〈0 0 1〉 final texture at 25 °C/h. This is due to the difference in intensity ratio of {1 0 0}〈0 1 1〉 to {1 1 1}〈1 1 2〉 in the cold-rolling texture which influences the nucleation of {1 1 0}〈0 0 1〉 component and the selective growth kinetics of various grains. In case of 18 ppm sulfur, the final texture was mainly composed of a sharp {1 1 0}〈0 0 1〉 component even at 400 °C/h, due to the relatively low segregation concentration.     

Growth process and structure of Fe/Si(1 1 1) ultrathin film: Transition from single-domain Fe(1 1 1)/Si(1 1 1) to β-FeSi2

The growth processes and structures of Fe/Si(1 1 1) ultrathin films grown by solid-phase reactive epitaxy were investigated by coaxial impact-collision ion scattering spectroscopy (CAICISS). It has been revealed that the Fe(1 1 1) thin films with a bcc-type structure were epitaxially grown on a Si(1 1 1) crystal, even at room temperature, and formed a single-domain structure: Fe(1 1 1)∥Si(1 1 1). After annealing at above 600 °C, the Fe(1 1 1) films were transformed into β-FeSi₂ via the collapse of the bcc-type structure to an amorphous or polycrystalline structure. On the basis of the thickness dependences of the growth processes, this phenomenon was discussed in terms of the diffusion of Si into Fe thin films.     

Photoemission from α and β phases of the GaAs(0 0 1)-c(4 × 4) surface

We prepared α- and β surface phases of GaAs(0 0 1)-c(4 × 4) reconstruction by molecular beam epitaxy (MBE) using As₄ and As₂ molecular beams, respectively, and examined them by angle-resolved ultraviolet photoelectron spectroscopy (UPS) and X-ray photoelectron spectroscopy (XPS) with synchrotron radiation as an excitation source. The UPS valence band spectra and the XPS 3d core level data show pronounced differences corresponding to the surface composition and the atomic structure of the two phases, as proposed in the literature. In UPS, the β phase is characterized by an intensive surface state 0.5 eV below the top of the valence band at low photon energy, while an analogous peak in the α phase spectra is missing. The surface state is interpreted in terms of dangling bonds on As dimers. The As3d and Ga3d core level photoelectron lines exhibit phase-specific shapes as well as differences in the number, position and intensity of their deconvoluted components. The location of various atoms in the surface and subsurface layers is discussed; our photoemission results support models of the β phase and the α phase with As-As dimers and Ga-As heterodimers, respectively.     

A study on the magnetic properties of carbon-doped (1 1 2? 0) ZnO thin films

By using the first principle method based on density functional theory (DFT), a study on the electronic structure and the ferromagnetic stability in C-doped (1 1 2¯ 0) ZnO thin films was conducted. It was found that the thin films have a FM ground state for a majority of configurations. It was also found that C atoms in the thin films have a clear clustering tendency. The ferromagnetism (FM) can be attributed to the coupling between C energy levels. The results showed that oxygen vacancies cannot stabilize the FM coupling of C-doped ZnO thin films. However, zinc vacancies can stabilize the FM coupling of the thin films, which indicates that hole-carriers play a crucial role in the observed FM behavior. In addition, the strain effect on the FM of C-doped ZnO thin films was also analyzed.     

The γ-Fe formation in epitaxial Cu(0 0 1)/Fe(0 0 1) thin films by the solid-state synthesis: Structural and magnetic features

The γ-Fe formation in epitaxial Cu(0 0 1)/Fe(0 0 1) bilayers with the annealing temperature increasing has been studied. Using Mössbauer spectroscopy, X-ray diffraction, and magnetic analysis, structural and chemical characterization of the interface between cooper and iron layers has been performed. After annealing at 850 °C and subsequent cooling to room temperature, paramagnetic γ-Fe(0 0 1) precipitates with an average size of 30 nm coherent to a Cu(0 0 1) matrix form. Conditions of intermixing and the γ-Fe formation at the Cu/Fe interface are explained in terms of the solid-state synthesis in thin films. Specific features of the martensitic transition γ↔α are discussed.     

An ab initio-based approach to phase diagram calculations for GaAs(0 0 1)-(2 × 4)γ surfaces

Surface phase diagram of recently proposed GaAs(0 0 1)-(2 × 4)γ is systematically investigated by using our ab initio-based approach. We focus on the (4 × 7) domain consisting of c(4 × 4)-like and (2 × 4)-like regions to clarify surface dimer constituents as functions of temperature T and As (As₂ and As₄) pressure p_As by comparing chemical potentials of surface dimers in the vapor phase with that on the surface. The calculated results under As₄ imply that Ga dimers in the c(4 × 4)-like region tend to become stable with increase of temperature and appear at the conventional growth condition such as T ∼ 800 K and p_As ∼ 10⁻⁶ Torr, while the (2 × 4)-like region favors As dimers. This is consistent with temperature dependence of change in surface dimer constituents on the c(4 × 4) and (2 × 4)β2 clarified in our previous study. Furthermore, the surface phase transition from the c(4 × 4) to (2 × 4)β2 via (2 × 4)γ is discussed on the basis of the phase diagram obtained in this study.     

Local bond rupture of Si atoms on Si(1 1 1)-(2 × 1) induced by the surface π-π∗ excitation

A scanning tunneling microscopy study has revealed that threefold-coordinated Si atoms at intrinsic sites of reconstructed (2 × 1) structure on the Si(1 1 1) surface are removed to form a surface monovacancy by an electronic mechanism under surface-specific optical transitions at 0.45 eV. This result provides direct evidence for the relaxation of excited surface electronic states as the origin of excitation-induced structural instability on semiconductor surfaces.     

Adsorption of molecular oxygen on the reconstructed β2(2 × 4)-GaAs(0 0 1) surface: A first-principles study

In this work, first-principles modeling techniques are used to investigate the mechanism(s) of adsorption of molecular oxygen on the GaAs(0 0 1)-(2 × 4) surface. The reaction of adsorption was modeled using ab-initio molecular dynamics at constant temperature for two thermal regimes, i.e. 300 K and 680 K, respectively. The resulting adsorbate configurations were relaxed using density functional theory and the adsorption energies were subsequently computed. Our results suggest a dominant mechanism of adsorption described by molecular dissociation, followed by oxygen insertion in the Ga-As bonds, bridging Ga-O-As chemical bonds. The electronic properties of the clean reconstructed GaAs(0 0 1) surface and the ones obtained after O₂ adsorption were computed. It is found that for the most stable adsorbate configuration, where oxygen is incorporated in a Ga-O-As unit, the associated density of electronic states is free of defect levels within the GaAs band gap region.     

Surface studies of 2,4-pentanedione on γ-Al2O3/NiAl (1 0 0) and NiAl (1 0 0)

The chemical compound 2,4-pentanedione (Hacac) has been shown to etch the oxidized metal surfaces metals such as copper and nickel, but not their unoxidized surfaces. Here it is shown that on the γ-Al₂O₃/NiAl (1 0 0) surface (oxidized NiAl (1 0 0)) etching of aluminum occurs at 170 K and 750 K. Reflection-absorption infrared spectroscopy (RAIRS) is used to show that Hacac binds to both the clean, metallic and oxidized surfaces, but decomposition and combustion products dominate on the metallic surface and no etching occurs. The binding process that involves a deprotonation reaction of the enol species was identified by redshift in the carbonyl peaks and the appearance of an Al-H peak observed in the IR spectrum. The implication of these results is that there is both an unusual low temperature and high temperature etching of the alumina by bound acac.     

Synthesis of azo benzothiazole polymer and its application of 1 × 2 Y-branched and 2 × 2 Mach–Zehnder interferometer switch

The azo benzothiazole polyurethane–urea (ABPUU) was synthesized from chromophore molecule 4-[(6-nitrobenzothiazole-2-yl)diazenyl]phenyl-1,3-diamine NBDPD, polyether polyol (NJ-210) and isophorone diisocyanate (IPDI). The structure, thermal property, mechanical property and physical property were characterized and investigated. The refractive index (n) and thermo-optic coefficient (dn/dT) of ABPUU was determined at different temperature and wavelength (532 nm, 650 nm and 850 nm) using attenuated total reflection (ATR) technique. Using the CCD digital imaging devices, transmission loss of ABPUU was measured. A 1 × 2 Y-branched and 2 × 2 Mach–Zehnder interferometer (MZI) switch with two rib waveguides, dual driving electrodes and two critical 3-dB couplers polymeric thermo-optic switches based on thermo-optic effect of prepared ABPUU were designed and simulation. The power consumption of the Y-branched switch is less than 0.84 mW. The Y-branched and MZI switching rising and falling times obtained are 0.8 ms and 0.2 ms, respectively.     

Catalysis of the hydrogen oxidation reactions by Sr-doped LaMn1 − yCryO3 ± δ oxides

Sr-doped and Sr-free La_1 − xSr_xMn_1 − yCr_yO_3 ± δ (LSMC, x(Sr) = 0-0.2, y(Cr) = 0.4-0.6) perovskite-type oxides were synthesized and evaluated as single phase anodes for use in intermediate temperature solid oxide fuel cell applications. Their thermo-chemical and chemical stabilities were investigated in hydrogen at high temperatures and correlated with their oxygen non-stoichiometry (3 ± δ), determined by permanganate titration. The catalytic activity towards hydrogen oxidation was examined as a function of oxide sintering time, operating temperature, and the Sr and Cr contents, using a Pt mesh current collector. While all of the perovskite oxides studied here showed some irreversible performance degradation with time under both open circuit and anodically polarized conditions, La_0.9Sr_0.1Mn_0.6Cr_0.4O_3.03 (LSMC9164), sintered at 1200 °C for 10 h, was found to be the most catalytically active and also the most stable.     

First-principles study of thiophene on β-SiC (0 0 1)-(2×1) surface

In this work, we performed density functional calculations to examine the molecular adsorption states of thiophene on β-SiC(0 0 1)-2×1 surface. A number of possible adsorption geometries are considered into two groups as the polymeric thiophene chain and the individual molecules covalently bonded onto the surface. The results show that the polymeric chain on the surface is the less stable adsorption case and individual arch like adsorption case structure is more stable than others. In all adsorption cases, the adsorbed SiC surfaces are characterized as different semiconductors.     

Current–voltage temperature characteristics of Au/n-Ge (1 0 0) Schottky diodes

The variation in electrical characteristics of Au/n-Ge (1 0 0) Schottky contacts have been systematically investigated as a function of temperature using current–voltage (I−V) measurements in the temperature range 140–300 K. The I–V characteristics of the diodes indicate very strong temperature dependence. While the ideality factor n decreases, the zero-bias Schottky barrier height (SBH) (Φ_B) increases with the increasing temperature. The I–V characteristics are analyzed using the thermionic emission (TE) model and the assumption of a Gaussian distribution of the barrier heights due to barrier inhomogeneities at the metal–semiconductor interface. The zero-bias barrier height Φ_B vs. 1/2 kT plot has been used to show the evidence of a Gaussian distribution of barrier heights and values of Φ_B=0.615 eV and standard deviation σ_s0=0.0858 eV for the mean barrier height and zero-bias standard deviation have been obtained from this plot, respectively. The Richardson constant and the mean barrier height from the modified Richardson plot were obtained as 1.37 A cm⁻² K⁻² and 0.639 eV, respectively. This Richardson constant is much smaller than the reported of 50 A cm⁻² K⁻². This may be due to greater inhomogeneities at the interface.     

Oxidation mechanism and ferryl domain formation on the α-Fe2O3 (0 0 0 1) surface

Recent experimental evidence calls for a reinterpretation of the oxidized structure in chemically distinct domains of the hematite (0 0 0 1) surface as the ferryl (FeO) termination rather than the bulk terminated O₃-Fe-Fe-R structure. Although this interpretation is consistent with experimental data and ab initio thermodynamics calculations, it raises serious questions about how molecular oxygen can be dissociated on a surface where reactive iron centers are slightly more than 5 Å apart. Here, we propose a novel cooperative bimolecular mechanism that provides a reasonable pathway for the formation of the unusual ferryl surface termination and should be readily reversible, which is important for understanding the function of hematite surfaces as an oxidation catalyst.     

Interaction of H2S with α-Fe2O3(0 0 0 1) surface

The atomic-scale structural changes in an α-Fe₂O₃ (hematite) (0 0 0 1) surface induced by sulfidation and subsequent oxidation processes were studied by X-ray photoemission spectroscopy, LEED, and X-ray standing wave (XSW) measurements. Annealing the α-Fe₂O₃(0 0 0 1) with a H₂S partial pressure of 1 × 10⁻⁷ Torr produced iron sulfides on the surface as the sulfur atoms reacted with the substrate Fe ions. The oxidation state of the substrate Fe changed from 3+ to 2+ as a result of the sulfidation. The XSW measured distance of the sulfur atomic-layer from the unrelaxed substrate oxygen layer was 3.16 Å. The sulfide phase consisted of three surface domains identified by LEED. Formation of the two-dimensional FeS₂ phase with structural parameters consistent with an outermost layer of (1 1 1) pyrite has been proposed. Atomic oxygen exposure oxidized the surface sulfide to a sulfate () and regenerated the α-Fe₂O₃(0 0 0 1) substrate, which was indicated by a (1 × 1) LEED pattern and the re-oxidization of Fe to 3+.     

Surface and redox chemistry of Sm0.95Ce0.05Fe1 − xNixO3 − δ perovskites

A new series of perovskite materials with formula Sm_0.95Ce_0.05Fe_1 − xNi_xO_3 − δ (0 ≤ x ≤ 0.10) has been prepared by sol-gel combustion via a citrate precursor route. X-ray diffraction data showed that materials prepared by this method had a single orthorhombic phase belonging to the Pnma (62) space group. The study of powders sintered in air and in reducing atmospheres reveals that these materials do not show phase separation in air (up to 1350 °C) nor under 5% v/v H₂/N₂ (up to 700 °C), but a phase separation of Sm₂O₃ does occur at and above 800 °C under 5% v/v H₂/N₂ without deterioration of the perovskite phase. The surfaces of all the powders (fresh, in-situ reduced and ex-situ reduced) were Sm rich, and multiple oxidation states for Fe were observed. XP analysis of in-situ reduced samples (800 °C and above) shows that metallic Fe forms in all nickel doped materials except x = 0.07. The surface oxygen vacancies and percentages of lattice and adsorbed oxygen for this series of Ni doped materials were determined and the oxygen recapturing ability is explained in terms of the multiple oxidation states of Fe.