Magnetic,electronic and structural properties of ZnxFe3−xO4

A series of samples Zn_xFe_3−xO₄ have been prepared by the chemical coprecipitation technique and characterized by X-ray diffraction (XRD), vibrating sample magnetometry (VSM) and X-ray photoelectron spectroscopy (XPS). XRD demonstrates all the samples of Zn_xFe_3−xO₄ have a spinel structure same as Fe₃O₄. The magnetic hysteresis loops of Zn_xFe_3−xO₄ obtained from VSM indicate that the saturation magnetization has a maximum when x is ∼1/3. The chemical states of Fe atoms and Zn atoms in zinc ferrites have been measured using XPS and Auger electron spectroscopy (AES). The Fe 2p core-level XPS spectra and Zn L₃M₄₅M₄₅ Auger peaks have been analyzed and the results have been discussed in correlation with the samples’ magnetic properties. These results suggest most of Zn atoms occupy the tetrahedral sites and a small amount of them occupy the octahedral sites.     

Dual behaviors of magnetic CoxFe1−x (0≤x≤1) nanowires embedded in nanoporous with different diameters

Co_xFe_1−x nanowire arrays with various diameters and different composition were fabricated by ac electrodeposition using porous alumina template. Coercivity along the easy axis reaches to a maximum at 2330 Oe, for Co_xFe_1−x nanowires containing about 40 at% Co. The crystalline structure of the nanowires was concentration-independent and shows a bcc structure. The critical diameter for transition from coherent rotation to curling mode is 35 nm for CoFe containing less than 40 at% Co while it is 30 nm for those with more than 40 at% Co. Optimizing the magnetic properties of CoFe with different Co content was seen to be dependent on the diameter of nanowires. For 25 nm diameter, the optimum was shown below 50 at% Co while it was seen above 50 at% for nanowires with 50 nm diameter. The angular dependence of the coercivity with nanowires diameter were also studied.     

Site preference and magnetism of Fe3−xCrxAl0.5Si0.5

In order to gain better insight into the origin of the observed differences between Fe_3−xCr_xAl and Fe_3−xCr_xSi, alloys of Fe_3−xCr_xAl_0.5Si_0.5 (x=0, 0.125, 0.250, 0.375 and 0.5) were prepared and studied by means of X-ray and neutron diffraction as well as by magnetization measurements. Electronic structure calculations of these alloys have been performed by means of TB-LMTO-ASA method. It was expected, and experimentally verified, that the presence of silicon and aluminum atoms in 1:1 proportion will result in the independence of the lattice parameter on the iron/chromium concentration. All samples have been proved to be a single phase of the DO₃-type of structure. Theoretical and experimental results indicate that chromium atoms locate preferentially in B sublattice. Cr magnetic moments are oriented antiparallel to Fe magnetic moments. Neutron measurements show a linear dependence of the magnetic moments of Fe(A,C), Fe(B) and Cr(B) as a function of Cr concentration. However the calculated total magnetic moment decreases faster with chromium content than indicated by the experiment.     

Magnetic properties of R2Fe17−xGax (R=Y and Gd) compounds

The magnetic properties of Y₂Fe_17−xGa_x for 3≤x≤7 and Gd₂Fe_17−xGa_x for 5≤x≤7 have been investigated using ⁵⁷Fe Mössbauer spectroscopy. These compounds have the rhombohedral Th₂Zn₁₇ structure. X-ray diffraction analysis of aligned powders shows that the easy direction of magnetization is parallel to the c-axis in Y₂Fe₁₀Ga₇ and Gd₂Fe₁₀Ga₇ and is perpendicular to the c-axis in Y₂Fe₁₄Ga₃, Y₂Fe₁₂Ga₅, Gd₂Fe₁₂Ga₅ and Gd₂Fe₁₁Ga₆. Mössbauer studies indicate that those samples are ordered ferromagnetically. The ⁵⁷Fe hyperfine field decreases with increasing Ga content. This decrease results from the decreased magnetic exchange interactions resulting from Ga substitution. The average isomer shift, δ, for R₂Fe_17−xGa_x (R=Y and Gd) at room temperature is positive and the magnitude of δ increases with increasing Ga content.     

High temperature ferromagnetism of the vacuum-annealed (In1−xFex)2O3 powders

(In_1−xFe_x)₂O₃ (x = 0.02, 0.05, 0.2) powders were prepared by a solid state reaction method and a vacuum annealing process. A systematic study was done on the structural and magnetic properties of (In_1−xFe_x)₂O₃ powders as a function of Fe concentration and annealing temperature. The X-ray diffraction and high-resolution transmission electron microscopy results confirmed that there were not any Fe or Fe oxide secondary phases in vacuum-annealed (In_1−xFe_x)₂O₃ samples and the Fe element was incorporated into the indium oxide lattice by substituting the position of indium atoms. The X-ray photoelectron spectroscopy revealed that both Fe²⁺ and Fe³⁺ ions existed in the samples. Magnetic measurements indicated that all samples were ferromagnetic with the magnetic moment of 0.49-1.73 μ_B/Fe and the Curie temperature around 783 K. The appearance of ferromagnetism was attributed to the ferromagnetic coupling of Fe²⁺ and Fe³⁺ ions via an electron trapped in a bridging oxygen vacancy.     

Study of Zn1−xCoxO (0.02≤x≤0.08) dilute magnetic semiconductor prepared by mechanosynthesis route

Single-phase Zn_1−xCo_xO (0.02≤x≤0.08) dilute magnetic semiconductor is prepared by mechanical milling process. The shift of XRD peaks towards the higher angle and a redshift in the band gap compared to the undoped ZnO ensure the incorporation of Co²⁺ ions in the semiconductor host lattice. Pure Zn_xCo_1−xO phases show the paramagnetic behavior in the temperature range 80 K≤T≤300 K. The room temperature volume magnetic susceptibility (χ_v) estimated in case of Zn_0.96Co_0.04O is ∼10⁻⁵ emu/Oe cm³. The temperature dependence of susceptibility χ_v can be fitted well with Curie law confirming the paramagnetic interaction. The observed crystal-field splitting of 3d levels of Co²⁺ ions inside Zn_1−xCo_xO has been successfully interpreted using Curie law.     

The effect of Fe doping on structural, magnetic and electrical transport properties of CaMn1−xFexO3 (x=0-0.35)

A comprehensive study of the effect of Fe doping on CaMnO₃ is carried out by means of experiments on the structural, transport conduction, and magnetic properties of CaMn_1−xFe_xO₃ (0≤x≤0.35). With a sol-gel process for sample preparation, Fe is substituted for Mn up to x=0.35. This substitution substantially brings out the lattice expansion and gradually suppresses the antiferromagnetism. For x=0.08 and 0.10 in particular, the magnetization curves with a field-cooled mode under the field of 1 kOe behave as those of a ferrimagnetic-like system and present low-temperature negative magnetization. For x≥0.15, the negative magnetization phenomenon disappears, and a ferromagnetic component coexists with an antiferromagnetic one, but the antiferromagnetic interaction still dominates in these compounds. Electrical transport measurements show insulating behavior for all compositions. Fe doping, even at a level as low as x=0.02, can cause a marked resistivity increase in the temperature range studied. Further increasing the Fe content causes the resistivity to gradually decrease due to the increasing carrier presence.     

Electronic structure and ferromagnetism of polycrystalline Zn1−xCoxO (0≤x≤0.15)

The electronic structure of polycrystalline ferromagnetic Zn_1−xCo_xO (0.05≤x≤0.15) and the oxidation state of Co in it, have been investigated. The Co-doped polycrystalline samples are synthesized by a combustion method and are ferromagnetic at room temperature. XPS and optical absorption studies show evidence for Co²⁺ ions in the tetrahedral symmetry, indicating substitution of Co²⁺ in the ZnO lattice. However, powder XRD and electron diffraction data show the presence of Co metal in the samples. This give evidence to the fact that some Co²⁺ ion are incorporated in the ZnO lattice which gives changes in the electronic structure whereas ferromagnetism comes from the Co metal impurities present in the samples.     

Spin polarization of Fe-rich ferromagnetic compounds in Ru2−xFexCrSi Heusler alloys

We report spin polarization P of Ru_2−xFe_xCrSi Heusler alloys by the Andreev reflection technique. Ru_2−xFe_xCrSi with L2₁-type structure and saturation magnetic moment of per formula unit is theoretically predicted to be half-metals in the wide range of the composition x. We had clarified that the experimental results of saturation magnetic moment in Fe-rich compounds had coincided with the theoretical prediction. Therefore, we have measured the differential conductance of Ru_2−xFe_xCrSi/Pb planar-type junctions. The P value of Ru_2−xFe_xCrSi was determined by fitting the differential conductance with the modified Blonder-Tinkham-Klapwijk theory. We have found that the behavior of P for Ru_2−xFe_xCrSi was independent of the composition x in the Fe-rich region; P=0.53 for both of x=1.5 and 1.7. The spin polarization is the similar value to Co-based Heusler alloys.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

Structure and superconductivity in FexCu1−xBa2YCu2O7+y superconductors synthesized by high pressure

Comprehensive studies of X-ray diffraction, oxygen content, superconductivity and Mössbauer effect have been made on Fe_xCu_1−xBa₂YCu₂O_7+y superconductors (0.00≤x≤0.70) synthesized by ambient (AM) and high pressure (HP). Results indicate that all the HP-samples have tetragonal structure, smaller lattice parameter c and unit-cell volume than the AM-samples. The studies of oxygen content, and Mössbauer spectroscopy indicate that the HP-samples have higher oxygen content, carrier concentration and average valence of Fe than the AM-samples. Moreover, for the HP-samples more Fe atoms located in CuO_x chains have fivefold-oxygen coordination. These are important reasons for the enhancement of T_c in the HP-samples.     

Magnetic properties of the Ce2Fe17−xMnx helical magnets up to high magnetic fields

Magnetic properties of the Ce₂Fe_17−xMn_x, x=0–2, alloys in magnetic fields up to 40 T are reported. The compounds with x=0.5–1 are helical antiferromagnets and those with 1<x?2 are helical ferromagnets or helical antiferromagnets at low and high T, respectively. Mn ions in the system carry average magnetic moment of 3.0±0.2 μ_B that couple antiparallelly to the Fe moments. Easy-plane magnetic anisotropy in the Ce₂Fe_17−xMn_x compounds weakens upon substitution of Mn for Fe. The absolute value of the first anisotropy constant in the Ce₂Fe_17−xMn_x helical ferromagnets decreases slower with increasing temperature than that calculated from the third power of the spontaneous magnetization. Noticeable magnetic hysteresis in the Ce₂Fe_17−xMn_x, x=0.5–2, helical magnets over the whole range of magnetic fields reflects mainly irreversible deformation of the helical magnetic structure during the magnetization of the compounds. A contribution from short-range order (SRO) magnetic clusters to the magnetic hysteresis of the helical magnets has been also estimated.     

Magnetic field induced order–order phase transition in magnetocaloric systems Mn2−xFexAs0.5P0.5 and MnFeAsyP1−y

An analysis is presented of experimental and theoretical results of the MnFeAs_yP_1−y (0.15≤y≤0.66) and Mn_2−xFe_xAs_0.5P_0.5 (0.5≤x≤1.0) systems to identify main traits that underlie the mechanism of formation of different antiferromagnetic (AF) phases in the two systems. The discrepancy between the calculated from first principles and experimental values of the magnetic moment in the ferromagnetic phase with cation substitution in the system Mn_2−xFe_xAs_0.5P_0.5 is due to the appearance of a canted magnetic structure. In this case, the emergence of an AF phase with decreasing iron concentration precedes a significant change in the electronic d-band filling. In the model of the spiral structure in the system of itinerant electrons it is shown that the stabilization of the AF phase with decreasing arsenic concentration, while maintaining the number of d-electrons, is a consequence of changes in the shape of the density of electronic states that occur with a decrease in unit-cell volume.     

Structural, magnetic properties and magnetostriction studies of Sm1−xNdxFe1.55 alloys

Structural, magnetic properties and magnetostriction studies of Sm_1−xNd_xFe_1.55 (0≤x≤0.56) alloys have been performed. X-ray diffraction analysis confirms the presence of single cubic Laves phase in Sm_1-xNd_xFe_1.55 alloys with 0≤x≤0.48. The lattice parameter of alloys increases linearly with increase in Nd content while the Curie temperature behaves in the opposite way. The alloy x=0.08 exhibits a giant magnetostriction value (λ_∥-λ_⊥) of −2187 ppm at a magnetic field of 12 kOe due to the anisotropy compensation between Sm³⁺ and Nd³⁺ ions.     

Synthesis, characterization and electromagnetic properties of Fe1−xCox alloy flower-like microparticles

Fe_1−xCo_x alloy microparticles with size 3-5 μm and novel flower-like shapes were prepared by a simple low temperature reduction method. The electromagnetic properties for the paraffin matrix composites containing Fe_1−xCo_x alloy microparticles were measured using a vector network analyzer in the 2-18 GHz frequency range. As a consequence of large surface- and shape-anisotropy energy for the flower-like shaped 3D microstructures, the strong natural resonance around 8-12 GHz and remarkable dielectric relaxation were observed in the complex permittivity and permeability spectrum, which are dominant in the enhanced electromagnetic wave absorption (EMA) performance. It was found that both the electromagnetic parameters of complex permittivity and permeability and the intensity and location of absorption band were remarkably dependent on the Co/Fe molar ratio. The enhanced EMA performance was obtained in these Fe_1−xCo_x-paraffin (x=0.4, 0.5, and 0.6) composites system. For the Fe_0.5Co_0.5 alloy, the reflection loss (RL) exceeding −20 dB was obtained in the broad frequency range of 5.4-18 GHz with a thin sample thickness of between 1.0 and 2.9 mm. In particular, an optimal RL of −59 dB was obtained at 3.61 GHz with a thin thickness of 3.6 mm for the Fe_0.4Co_0.6 sample. The Fe_1−xCo_x alloy microparticles may be attractive candidates for applications of microwave absorption materials with a wide frequency range and strong absorption in the high frequency region.     

Structure, transport and magnetic properties in La2xSr2−2xCo2xRu2−2xO6

The perovskite solid solutions of the type La_2xSr_2−2xCo_2xRu_2−2xO₆ with 0.25≤x≤0.75 have been investigated for their structural, magnetic and transport properties. All the compounds crystallize in double perovskite structure. The magnetization measurements indicate a complex magnetic ground state with strong competition between ferromagnetic and antiferromagnetic interactions. Resistivity of the compounds is in confirmation with hopping conduction behaviour though differences are noted especially for x=0.4 and 0.6. Most importantly, low field (50 Oe) magnetization measurements display negative magnetization during the zero field cooled cycle. X-ray photoelectron spectroscopy measurements indicate the presence of Co²⁺/Co³⁺ and Ru⁴⁺/Ru⁵⁺ redox couples in all compositions except x=0.5. Presence of magnetic ions like Ru⁴⁺ and Co³⁺ gives rise to additional ferromagnetic (Ru-rich) and antiferromagnetic sublattices and also explains the observed negative magnetization.     

Magnetoresistance in La1−xCaxMnO3 (0≤x<0.4)

The magnetic and transport properties of La_1−xCa_xMnO₃ (0≤x<0.4) have been systematically studied. The magnetoresistance (MR) maximum appears at x=0.2-0.25 and the temperature dependence of MR for x>0.25 shows a much broader profile than that of samples for x=0.2-0.25. Based on a scenario in which there is a short-range charge ordering (CO) state coexisting in the ferromagnetic state matrix for x>0.25, and the least or even no short-range CO state exists in samples for x=0.2-0.25, the above observations can be understood.     

Magnetic transitions and magnetostrictive properties of Laves compounds Sm0.88Nd0.12(Fe1−xCox)1.93

The structure, magnetic and magnetostrictive properties of Sm_0.88Nd_0.12(Fe_1−xCo_x)_1.93 (0≤x≤1.0) alloys have been investigated. The alloys have the cubic MgCu₂ structure over the whole composition range and the lattice parameter a decreases with increasing x. For 0≤x≤0.2, substitution of Co for Fe slightly increases the saturation magnetization M_s and Curie temperature T_c, while further substitution causes a decrease in both M_s and T_c. The spin reorientation is observed, and a phase diagram for the spin configurations of the Sm_0.88Nd_0.12(Fe_1−xCo_x)_1.93 system is determined. The spontaneous magnetostriction λ₁₁₁ increases as x is increased, while a monotonic decrease of the saturation magnetostriction λ_s with x originates from the increase of λ₁₀₀ with opposite sign to that of λ₁₁₁, which may be caused by the filling of the d band due to Co substitution.     

Critical behavior in Co-doped manganites La0.67Pb0.33Mn1−xCoxO3 (0≤x≤0.08)

The critical properties of perovskite manganite La_0.67Pb_0.33Mn_1−xCo_xO₃ (0≤x≤0.08) around the paramagnetic-ferromagnetic phase transition are investigated through various techniques such as the modified Arrott plot, Kouvel-Fisher method and critical isotherm analysis. Though the nature of this transition was found to be in second order, the estimated critical exponents β (0.233≤β≤0.368), γ (1.03≤γ≤1.40) and δ (4.32≤δ≤5.54) are in between the theoretically predicted values for three-dimensional Heisenberg and tricritical mean-field model. This model suggests the coexistence of the short-range and long-range ferromagnetic orders around the critical temperature. The values of the critical exponents obtained from different methods and the well-obeyed scaling behavior confirm that the calculated exponents are unambiguous and purely intrinsic to the system.     

Li0.5Fe2.5−xMnxO4 ferrite sintered from microwave-induced combustion

Li_0.5Fe_2.5−xMn_xO₄ (0≦x≦1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, ferric nitrate, manganese nitrate and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Mn-substituted lithium ferrite powders. The resultant powders annealed at 650 ^°C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the Mn content were strongly influenced the magnetic properties and Curie temperature of Mn-substituted lithium ferrite powder. As for sintered Li_0.5Fe_2.5−xMn_xO₄ specimens, substituting an appropriate amount of Mn for Fe in the Li_0.5Fe_2.5−xMn_xO₄ specimens markedly improved the complex permeability and loss tangent.